SPECIAL REPAIRS TO BLDG NO. P-48 (MES JCOs and EQV LIVING) AND SPECIAL REPAIRS TO BLDG NO. P-75 AT DSC LINE UNDER GE HADDO, PORT BLAIR

Amount

Taking down cement plaster of any description on brick or stone walls etc., including raking out joints, hacking for key, scrubbing down with water etc., and removal of debris to outside MD land complete all as specified and as directed.

M&L for rendering 15mm thick in two coats 5mm thick in CM (1:4) mixed with integral water proofing compound @ 3% by weight of cement over 10mm thick in CM (1:6) on fair faces of brick work or concrete, surfaces finished fair and even complete all as specified and as directed. NOTE: Water proofing compound will be measured and paid separately under relevant item of this schedule.

M&L for rendering 10mm thick in CM (1:6) on fair faces of brick work or concrete, surfaces finished fair and even complete all as specified and as directed.

M&L for applying bonding slurry coat on the wall and ceiling surface upto depth of 20mm using Nito Bond AR manufactured by M/s FOSROC Chemical (India ) Pvt Ltd or equivalent in Dr. Fixit or Harjas Coatings & Polymers (Coverage of 4 to 5 Sqm/Ltrs) complete all as specified and directed

Taking down of damaged, loosened cement concrete/cement mortar in walls and similar structural members up to depth of 20mm to 40mm, cleaning the dismantled portion with wire brush etc remove dust , dirt and other foreign particles etc., and washing with water with pressure and applying bonding agent on old concrete surfaces (wall & ceiling) all as specified and as per manufacturers instructions, Over prepared surfaces provide 20mm thick high build polymer modified cement sand mortar (1:3) mixed with 7 litres (minimum) Nitobond SBR per 50 kilograms of cement of M/s FOSROC Chemical (India ) Pvt Ltd or equivalent in Dr. Fixit or Harjas Coatings & Polymers including necessary scaffolding up to 15 m and including match the existing shade of surface complete all as specified and directed

Demolition of PCC block masonry, built in cement mortar including all quoins, arches, pillars etc., but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

M&L for precast cement concrete block masonry with solid blocks using PCC 1:3:6 type C1 exc.10cm in width and setting in CM 1:4 complete all as specified.

M&L for pre-cast cement concrete solid building blocks or slabs made up of (1:3:6) type C1 (using 20mm graded stone aggregate), 10cm thick (with plain or interlocking joints as directed) and setting in cement mortar 1:4 complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls of any description and applying two coats of distemper oil emulsion over a coat of primer after levelling the undulations if any with cement putty complete all as specified and as directed.

M&L for preparation of newly plastered ceiling surfaces applying two coats of distemper oil emulsion over a coat of primer complete all as specified and as directed.

M&L for preparation of newly plastered surfaces and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and as directed.

M&L for complete removal of existing treatment on wall by scrapping, washing, cleaning etc with 3mm average thick wall care putty and applying two coats of acrylic emulsion distemper over one coat primer including filling of cracks, holes and including leveling the surface which undulation found with wall care putty etc. all as specified.

M&L for complete removal of existing treatment of walls by scraping, washing, cleaning etc, and applying two coats of distemper oil emulsion over a coat of primer complete all as specified and as directed.

M&L for complete removal of existing treatment of ceiling by scraping, washing, cleaning etc, and applying two coats of distemper oil emulsion over a coat of primer complete all as specified and as directed.

M&L for preparation of plastered or unplastered surfaces of walls and applying three coat of white wash after filling the cracks, holes with filler complete all as specified and as directed.

M&L for PCC (1:5:10) type E2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed.

M & L for PCC 1:2:4 type B1 using 20 mm graded crushed stone aggregate as in filling, foundation and mass concrete duly mixed with water proofing compound @ 3% by weight of cement complete all as specified and directed.

Supply only integral water proofing compound.

M&L for complete removal of existing treatment by scraping, washing, cleaning etc., and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and as directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for non-skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floors etc, laid over and including 15mm thick screed bed in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for non-skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, as in floors etc, laid over and including 15mm thick screed bed in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for glazed ceramic designed coloured tiles in vertical surfaces using size of tiles 350x250x7mm / 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with colour of tile with and including 10mm thick backing coat in CM (1:3), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for non-skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors etc, laid over and including 15mm thick screed bed in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for non-skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, for work on vertical surfaces such as skirting, dados and risers to steps etc., including 10mm thick backing coat in CM (1:3), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for cutting out existing cracks in concrete surfaces / masonry wall / slab forming grooves 25mm x 40mm size, cleaning the groove thoroughly with blower, applying primer coat of the mix of IPH CC or Hydroseal Siliconate Epoxy resin & hardner in equal proportion with spray gun suitable brush to form a film on the surface of groove, filling the groove with putty made by mixing IPH CC in equal proportion of make Hajras Coating and polymers or Hydroseal Siliconate Epoxy Resin, hardner and admixture in the proportion of 1:1:2 and finally applying the sealing coat of the same mix and in the manner primer coat is applied following minimum coverage per running meter length of groove complete all as specified and directed.

Taking up or down 15mm dia steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down 20mm dia steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

S&F 20mm bore CPVC pipes SDR 13.5 & Plain CPVC SDR 11 fittings, fixed complete to walls, ceilings or in floors etc., (including concealing, if required) and to any type of pipe complete all as specified and as directed.

S&F 25mm bore CPVC pipes SDR 13.5 & Plain CPVC SDR 11 fittings fittings, fixed complete to walls, ceilings or in floors etc., (including concealing, if required) and to any type of pipe complete all as specified and as directed.

S&F 32mm bore CPVC pipes SDR 13.5 & Plain CPVC SDR 11 fittings fittings, fixed complete to walls, ceilings or in floors etc., (including concealing, if required) and to any type of pipe complete all as specified and as directed.

M&L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring etc., and making good, cutting not exc 10 cm girth in PCC block masonry/RCC complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames), area not exceeding 1.5 Sqm each complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames), area exceeding 1.5 Sqm but not exceeding 4.0 Sqm each complete all as specified and as directed.

Taking down shutters of any description, area not exceeding 1.0 Sqm each complete all as specified and as directed.

Taking down shutters, area exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and as directed.

M&L for anodised aluminium partition, window and door/ventilator with frame and shutters and grill fully or partly glazed, sliding/openable/fixed fully glazed and panels fixed with panels inserts 12 mm thick pre-laminated particle board/sheet glass including necessary jointing cleats, glazing clips, rubber beading, neoprene packing, anodised aluminium snap beading, screws, anodized aluminium fittings such as handles, aluminium butt hinges, aluminium tower bolts etc. The size of aluminium section shall be all as specified in relevant IS Code and SSR Part-I complete all as specified and as directed. NOTES: (i) Supply only floor spring, glass, Imax hinges, SS friction hinges, particle board, aluminium fly proof mesh will be measured and paid separately under relevant items of this BOQ. (ii) Weight of aluminium section only shall be accounted for the purpose of payment. However unit rate quoted shall be deemed to include for cost of rubber beading, neoprene packing, fittings such as handles, butt hinges, tower bolts, rollers for sliding windows, locking arrangement and fixing only of panel inserts of glass/ particle board/aluminium fly proof mesh etc. (iii) Weight of aluminium handle, butt hinges, tower bolts shall not be accounted for payment purpose.

Fixing only in repair for aluminium partition, window and door/ventilator with frame and shutters and grill fully or partly glazed, sliding/openable/fixed fully glazed and panels fixed with panels inserts 12 mm thick pre-laminated particle board/sheet glass including necessary jointing cleats, glazing clips, rubber beading, neoprene packing, anodised aluminium snap beading, screws, anodized aluminium fittings such as handles, aluminium butt hinges, aluminium tower bolts etc. The size of aluminium section shall be all as specified in relevant IS Code and SSR Part-I complete all as specified and as directed. NOTE: (i) Supply only floor spring, glass, Imax hinges, SS friction hinges, particle board, aluminium fly proof mesh will be measured and paid separately under relevant items of this BOQ. (ii) Weight of aluminium section only shall be accounted for the purpose of payment. However unit rate quoted shall be deemed to include for cost of rubber beading, neoprene packing, fittings such as handles, butt hinges, tower bolts, rollers for sliding windows, locking arrangement and fixing only of panel inserts of glass/ particle board/aluminium fly proof mesh etc. (iii) Weight of aluminium handle, butt hinges, tower bolts shall not be accounted for payment purpose.

Supply only 12mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side with balancing white lamination complete all as specified and as directed.

Supply only aluminium expanded metal fly proof mesh, cut to required size and shape, with 0.45mm nominal dia of wire and average width of aperture 1.40mm complete all as specified and as directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing fixed to door frame in repairs complete all as specified and as directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube as per specification & drawing, fixed in opening complete all as specified and as directed.

S&F 100mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised, type B-21 complete all as specified and as directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

S&F 200mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified and as directed.

S&F sliding door bolt, 300mm long, aluminium alloy, anodised, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and as directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm complete all as specified and as directed.

Demolition of cement concrete (un reinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of cement concrete (un reinforced) of any description as in padding (other than ground floors) complete all as specified and as directed.

M&L for 75mm thick PCC (1:3:6) type C1 (using 20mm graded stone aggregate) as in plinth protection, surface of concrete finished even and smooth without using extra cement complete all as specified and as directed.

S&F Harrison rails (curtain rails), 25mm dia, mild steel, chromium plated with fixing brackets, stops, rollers etc., fixed in repairs complete all as specified and as directed.

M&L for PVC valveless, syphonic action type, flushing cistern, 10 litre capacity, low level, white, with inlet, ball valve, float and handle including brackets, fixed in repairs complete all as specified and as directed.

M&L for vitreous China, wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinging device, fixed in repairs complete all as specified and as directed.

M&L for vitreous China wash hand basin, white, flat back, size 550mm x 400mm including cutting for and pinning in ends of brackets or erecting stand, 32mm dia waste coupling brass chromium plated, bottle trap 32mm bore brass chromium plated with necessary packing union and caps, chain and plug, PVC connections 15mm size with PTMT nuts of length 450mm, screwed down for iron pipe or for unions, fixed in repairs complete all as specified and as directed.

M&L for vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests, P or S trap including provision of lime concrete bedding with and including PVC valveless, syphonic action type, flushing cistern 10 litre capacity, low level, white, with inlet, ball valve, float and handle including brackets, flush pipe of polyethylene of low or high density or PVC 32 mm dia, PVC connections 15mm size with PTMT nuts of length 450mm, fixed in repairs complete all as specified and as directed.

S&F vitreous China urinal with top inlet, half stall type coloured complete fixing with suitable fixing arrangements to wall in cement mortar (1:2), securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in white cement with and including 32mm dia waste pipe in low density polyethylene (LDPE) of pressure rating 6 kgf/sqcm of 1.0 metre length, PVC connections 15mm size with PTMT nuts of length 450mm, concussive push button taps 15mm dia or bore, cast copper alloy, screwed for iron pipe, urinal spreader of PTMT any colour for fixing with 15 mm dia pipe (minimum weight 60gms), fixed in repairs complete all as specified and as directed.

M&L for PVC connections 15mm size with PTMT nuts of length 600mm, fixed in repairs complete all as specified and as directed.

S&F bib tap, brass, 15mm dia, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule, fixed in repairs complete all as specified and as directed. MAKE: PRAYAG Cat part No. PIS-08H or equivalent in PARRYWARE/ZOLOTO/JOHNSON

S&F over head shower rose & shower arm with or without swivel joints, brass, chromium plated, fixed to brass ferrule or pipe 125mm dia or bore, complete all as specified and as directed. MAKE: JAQUAR Cat part No. OHS-1985 or equivalent in PARRYWARE/ ZOLOTO/ JOHNSON

S&F stop valves 15mm dia or bore, cast copper alloy, fancy type with long shank and cup (concealed type), chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, fixed in repairs complete all as specified and as directed.

S&F soap dish, fixed in repairs complete all as specified and as directed. MAKE: JAQUAR Cat part No. AQN-7731 or equivalent in PARRYWARE/ PRAYAG/ JOHNSON

S&F angular stop cock, 15mm dia, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, with long shank and cup (concealed type) screwed down, screwed both ends for iron pipe or for unions, fixed in repairs complete all as specified and as directed. MAKE: JAQUAR Cat part No. CON-053KN or equivalent in PARRYWARE/ZOLOTO/JOHNSON

S&F tubular towel rail, brass, chromium plated, 20mm dia, D type, 60cm long between flanges, fixed in repairs complete all as specified and as directed. MAKE: JAQUAR Cat part No. AQN-7711

S&F in repairs stainless steel grating cover 100mm dia fixed with white cement complete all as specified

S&F hand shower (health faucet) with 15mm dia and 1.25 m long flexible tube with wall hook, fixed in repairs complete all as specified and as directed. MAKE: JAQUAR Cat part No. ALD-573

Supply and fix 9mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination fixed with screws to timber framework or wall complete all as specified and as directed.

S&F 100mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

S&F 100mm size Hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed.

S&F stainless steel hinges 75mm, stainless steel pin, anodised and fixed complete all as specified and as directed.

M&L for reinforced cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, cooking platforms and in shelves and the like complete all as specified and as directed.

M&L for plain cement concrete (1:2:4) type B0 (using 12.5mm graded stone aggregate) as in roof padding/sunken floors and similar work complete all as specified and as directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces of concrete flat complete all as specified and as directed.

S&F 75mm bore PVC (SWR) pipes , in any length with rubber ring joints laid in trenches or in floors using synthetic rubber adhesive cement solvent complete all as specified and as directed.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls using synthetic rubber adhesive cement solvent complete all as specified and as directed.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors in weep holes using synthetic rubber adhesive cement solvent complete all as specified and as directed.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls using synthetic rubber adhesive cement solvent complete all as specified and as directed.

S&F PVC (SWR) floor trap with grating including jointing with solvent cement, diameter of outlet 75 mm complete all as specified and as directed.

S&F PVC (SWR) elbow with oval access door, any radius, diameter of outlet 75 mm complete all as specified and as directed.

S&F PVC (SWR) junction single, (Single T) equal or unequal, diameter of outlet 75 mm complete all as specified and as directed.

S&F PVC (SWR) bends any radius, diameter of outlet 110 mm complete all as specified and as directed.

S&F PVC (SWR) junction single, (Single T) equal or unequal, diameter of outlet 110mm complete all as specified and as directed.

Taking down existing roof membrane and removing the debris from site and cleaning the surface with water complete all as specified and as directed.

M&L for screed bed 15mm thick in CM (1:4) on RCC roof slab, surfaces finished even and smooth without using extra cement duly mixed with water proofing compound @ 3% by weight of cement complete all as specified and as directed. NOTE: Water proofing compound will be measured and paid separately under relevant item of this schedule.

M&L for preparing plastered surfaces and applying a coat of cold applied bituminous primer over cleaned roof/ sunken surface @ 0.30 Kg/sqm and applying one coat of hot blown bitumen 85/25 grade @ 1.2 Kg/Sqm over primer followed by 3 mm thick APP modified 5-layered polymeric water proofing membrane weighing not less than 3.0 Kg/sqm reinforced with polyester non-woven fabric weighing not less than 150 grams/sqm laid as per the manufacturer instructions with side over lap of 100mm & end over lap of 150mm & tucked into the chases on roof, sunken slabs, edges and vertical surfaces and finally finishing the APP membrane surface with bituminous aluminium paint @ 0.15 Kg/sqm complete all as specified and directed. MAKE: STP Limited/ PIDILITE INDUSTRIES LIMITED (Dr. FIXIT TORCHSHIELD P3160)/ IWL INDIA LTD

M&L for preparation of old steel surfaces of any description, not otherwise described, over 10cm in width or girth and applying two coats of synthetic enamel paint of first quality over a coat of red oxide zinc chrome primer complete all as specified and as directed.

M&L for preparation of old wooden surfaces of any description, not otherwise described, over 10cm in width or girth and applying one coat of synthetic enamel paint of first quality over a coat of pink primer complete all as specified and as directed.

M&L for preparation of old plastered surfaces of walls and applying one coat of white wash after filling the cracks, holes with filler complete all as specified and as directed.

M&L for preparation of old plastered surfaces of ceilings and applying one coat of white wash after filling the cracks, holes with filler complete all as specified and as directed.

S&F Second class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints including preservative treatment complete all as specified and as directed.

S&F 35mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a), fixed to chowkats complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description, not otherwise described, over 10cm in width or girth and applying two coats of synthetic enamel paint of first quality over a coat of pink primer complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar

M&L for Machine cut kota stone slab flooring 20-25mm thick over 15mm thick cement screed base of CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar over 10mm thick cement screed base of CM 1:3 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for glossy finished heavy duty chequered cement concrete tiles 30cm x 30cm x 25mm thick, made of grey cement and pigments, machine pressed as in flooring, set, jointed and pointed in neat cement slurry laid over and including 20mm thick screed bed in CM (1:4) complete all as specified and as directed.

M&L for 18 to 20mm thick granite slab (of approved shade), machine cut, as in floors, vertical surfaces, steps (treads/risers) and the like laid over cement mortar (1:4) and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding, polishing and rounding (chamfering) the edges complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc., complete all as specified and as directed.

M&L for mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings etc., complete all as specified and as directed.

S&F pre-painted zinc coated aluminum sheet (Galvalume) GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. NOTES: The self tapping screw shall be of adequate length to drive into complete thickness of purlin/rafter etc., and shall be fixed using neoprene and EPDM washers. Penetration and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc., as per SSR Part-I 2009 complete.

S&F aluminum flat iron wind ties of any size and thickness fixed with self tapping screws for fixing roofing sheets complete all as specified and as directed. NOTES: The self tapping screw shall be of adequate length to drive into complete thickness of purlin/rafter etc., and shall be fixed using neoprene and EPDM washers.

M&L for mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-410-W (Gde E-250) Quality 'A' complete all as specified and as directed.

M & L for preparing of new of previously untreated steel surface of any description, not otherwise described, over 10 cm width or girth applyig two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

SUPPLY ONLY 5.5 mm thick sheet glass, ordinary quality and glazing with aluminium glazing clips in square exceeding 0.5 Sqm in each pane complete all as specified and as directed.

SUPPLY ONLY 4mm thick sheet glass, ordinary quality and glazing with aluminium glazing clips in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F kitchen sink with drainage board made of stainless steel 1mm thick with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, fixed in repairs complete all as specified and as directed.

S&F plate rack of stainless steel of size 31"x36"x10" with steel shelves, partitions & hanging arrangements for utensils, fixed in repairs complete all as specified and as directed. MAKE: PRAYAG Cat part No. P-348 or equivalent in JAQUAR/PARRYWARE

Taking down carefully old unserviceable aluminum/ copper point wiring (light, fan, socket or power) complete, including fittings & fixtures such as switches, ceiling roses, lamp holders, pendants, regulators sockets, light fittings, junction/terminal boxes etc; removing from site and making good disturbed surfaces of walls, floors etc., to match with existing surrounding surfaces complete all as specified and as directed.

Taking down existing unserviceable sub main wiring of any description and making good disturbed surfaces to match with existing surrounding finishes complete all as specified and as directed.

Taking down old Unserviceable fuse unit / DBs with MCB/MCCB415 Volt/ 230 volt

Taking down carefully old unserviceable light fittings only and removing from site complete all as specified and as directed.

Taking down carefully old unserviceable light fittings of any type and refixing the same afyter completed the B/R work complete all as specified and as directed.

M&L for Point wiring complete with 1.5 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral), drawn through and including rigid non metallic PVC casing and capping of suitable size (not less than 25mm) and accessories fixed on walls/ceilings etc., including provision of PVC insulated 1.5 Sqmm FRLS cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk in CI boxes/pressed steel terminal boxes 60mm deep made out of 1.6mm thick MS sheet duly painted with two coats of anti-corrosive paint outside and with two coats of aluminium paint inside and laminated sheet cover of 3mm thick on top for housing the switches, socket outlet etc, all as specified and as directed for Make of wire : Polycab / Gloster / Anchor / Havells / Finolex / Anchor Make of PVC Casing & Caping : Modi / Precision / Supreme / Finolex / Polycab

ONE LIGHT/FAN point controlled by one, one way 6 Amps switch.

ONE 6A SOCKET OUTLET point controlled by one, one way 6 Amps switch on independent board.

ONE 6A SOCKET OUTLET point controlled by one, one way 6 Amps switch on same board.

M&L for Point wiring complete with 4.0 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral), drawn through and including rigid non metallic PVC casing and capping of suitable size (not less than 25mm) and accessories fixed on walls/ceilings etc., including provision of PVC insulated 4.0 Sqmm FRLS cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk in CI boxes/pressed steel terminal boxes 60mm deep made out of 1.6mm thick MS sheet duly painted with two coats of anti-corrosive paint outside and with two coats of aluminium paint inside and laminated sheet cover of 3mm thick on top for housing the switches, socket outlet etc, all as specified and as directed for ONE 16A SOCKET OUTLET point controlled by one, one way 16 Amps modular switch on independent board.

S&F switch piano, flush type, single pole, one way, 6 Amps, 240 volts complete all as specified and as directed. Make: Legrand/ Anchor / Cona

S&F switch piano, flush type, single pole, one way, 16 Amps, 240 volts complete all as specified and as directed. Make: Legrand/ Anchor / Cona

S&F switch socket outlet,2 in 1, 3 pin, 6A, flush type, multipurpose, 240 volts complete all as specified and as directed. Make: Legrand/ Anchor / Cona

S&F switch socket outlet,2 in 1, 3 pin, 16A, flush type, multipurpose, 240 volts complete all as specified and as directed. Make: Legrand/ Anchor / Cona

M&L for ceiling rose, three terminal, 65x20mm size, PVC/Polycarbonate, insulated body, 6A, 240 volts complete all as specified and as directed. Make: Legrand/ Anchor / Cona

S&F modular electronic fan regulator for ceiling fan, step type, 5 speed, AC, 2 module, 120 watts, 240 volts complete all as specified and as directed. Make: Legrand/ Anchor / Cona

Taking down carefully ceiling fan of any make or any size from its location and refixing at the same location after necessary repairs works including painting with approved quality of super enamel paint complete all as specified and as directed

Taking down carefully Exhaust fan of any make or any size from its location and refixing at the same location after necessary repairs works including painting with approved quality of super enamel paint complete all as specified and as directed

Taking down burnt winding of ceiling fan motor of 1200 / 1400mm sweep and M&L of rewinding with new copper winding wire of same gauge with approved quality of super enameled copper winding wire including varnishing heating, including painting of existing colour etc complete all as specified and directed.

Taking down burnt winding of exhaust fan motor of 130 / 380 /450 mm sweep and M&L of rewinding with new copper winding wire of same gauge with approved quality of super enameled copper winding wire including varnishing heating, including painting of existing colour etc complete all as specified and directed.

S&F Ball bearing of ceiling fan No. 6201/6202 complete all as specified and as directed.

S&F Ball bearing of ceiling fan shaft suitable for 1200 / 1400mm sweep ceiling fan complete all as specified and as directed.

S&F Ball bearing of fan blade for ceiling 1200 / 1400mm sweep complete all as specified and as directed.

M&L for Sub main wiring complete with two runs (1P+1N) of 6.0 Sqmm single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor and one run of 6.0 Sqmm single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor as earth wire green in colour including lugs, drawn through and including 32mm wide rigid non-metallic PVC casing and capping and its accessories (OR) 20mm dia PVC conduit and conduit accessories fixed on surface of wall/ceiling/roof/ floor complete all as specified and as directed. NOTE: Two runs of 6.0 Sqm copper conductor, One run of 6.0 Sqmm copper conductor as earth wire and one run of PVC casing and capping / PVC conduit shall be measured as one unit length. Make : Polycab / Gloster / Anchor / Havells / Finolex / Anchor

S&F SPN DB sheet metal enclosure double door suitable (IP-43) Protection, 8 Way with 200 Amp rated standard bus bar of suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated complete. Make : Havells/L&T/Legrand/Indo Asian

S&F MCB, SPN, "C" series, 240 volts, 40 Amps, 10 KA rupturing capacity complete all as specified and as directed. Make : Havells/L&T/Indo Asian/Legrand/Schneider

S&F MCB, SP, "C" series, 240 volts, 6-32 Amps, 10 KA rupturing capacity complete all as specified and as directed. Make : Havells/L&T/Indo Asian/Legrand/Schneider

S&F Tube light fittings LED 20 watts 4 feet including all accessories and fixing arrangements complete all as specified and directed Make :CG Cat Part No : CCS-100-20-65-HL2-DP-NWH/ Philips Cat Part No : Astra line plus/C&S/Havells Note : Quoted rate is inclusive of any other misc materials required for fixing new fittings

S&F Tube light fittings 2 feet mirror optical including all accessories and fixing arrangements complete all as specified and directed. Make : Philips Model No LED 48027/65/86 ultron/ CG Cat No LCL-14-CDL/Havells Note : Quoted rate is inclusive of any other misc materials required for fixing new fittings

M&L for earthing complete with GI earth plate electrode of size 600mmx600mmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of the earth plate not less than 1.5m below normal ground level connected to 4mm dia GI earth wire as earth lead connected by means of bolts, nuts, washers and check nuts made out of galvanised iron or steel all as shown on electrical plate No. 3 of SSR Part-I connected to common earth dolly including testing on completion complete all as specified and directed. NOTES: 1) The unit rate shall also include for earth work in any type of soil, PCC (1:3:6) type C1 chamber, pre-cast RCC (1:2:4) type B-1 using 20mm graded stone aggregate cover 50mm thick reinforced with TMT bars 8mm dia @ 100mm c/c both ways, funnel with watering pipe 20mm dia medium grade, GI protection pipe light grade 40mm dia and wire mesh complete in addition to item No. 1(a) to (e) of preamble (notes) under sub-heading earthing, specified on Sl. Page Nos. 422 & 423 of SSR Part-II. 2) Earthing lead and GI protection pipe beyond 7.5m will be measured and paid separately.

M/S TANISHA ENTERPRISES

CHANDER SEKER ENTERPRISE

LOOK UP ENTERPRISES

SHUBHAM SHANKAR GAIKWAD

V KARTHICK

Bismi Builders & Enterprises

CARTWHEEL CONSTRUCTION

Sree Tirumala Enterprises