SPECIAL REPAIR TO BLDG NO JP-30, JP-31 AND JP-145 AND CERTAIN SANCTIONED WORKS UNDER AGE B/R-I AT ALWAR

Amount

Demolition of brick/stone masonry built in cement/lime mortar of any mix including all quoins pillar ashlars masonry and removal complete all as specified and directed by Engineer-in-Charge.

M&L brick work with fly ash bricks (As per IS-13757 (1993) burnt clay fly ash building bricks), (Old size bricks) straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L brick work with fly ash brick straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (un-renforced) in ground floor and paving not exc 15cm thickness (below or above ground level) and removal of rubbish material complete all as specified and directed by Engineer-in-Charge.

M&L for PCC (1:2:4) type B-1 (using 20mm graded stone aggregate), 25mm thick, as in sub base complete all as specified and directed by Engineer-in-Charge.

M&L for coloured non skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L non skid ceramic tiles colored 300mm x 300mm x 7mm thick in floor set and jointed in neat cement slurry and pointed in white or coloure cement and over 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engineer-in-Charge. Make : Somany/ Johnson /Kajaria.

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but ot backing), removing serviceable tiles to store and rubbish off the premises

M&L glazed ceramic coloured tiles in vertical surface 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles and over 10 mm thick rendring in cm 1:4 complete all as specified & directed by Engineer-in-Charge. Make : Somany/Johnson/Kajaria.

M&L machine cut kota stone slab flooring 20-25mm thick over 20 mm thick screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-Charge.

M&L machine cut kota stone slab 20-25mm thick in steps for riser, dado, skirting, wall etc over 20 mm thick screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-Charge.

M&L for granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including cutting and polishing types and over screed bed 20 mm thick CM 1:6 cement concrete complete all as specified and directed by Engineer-in-Charge.

M&L 75 mm thick PCC(1:3:6) type C1 (using 20mm graded stone aggregate ) as in plinth protection finished fair and even complete all as specified & directed by Engineer-in-Charge.

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc all as directed.

M&L rendering 10mm thick in cement mortar 1:6 on fair faces of stone masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified.

M&L rendering 15mm thick in CM 1:4 on stone wall surfaces or other than fair faces of brick work & surfaces finished even and smooth without using extra cement with water proof compound (water proof compound paid seperatly) all as specified.

M&L for rendering 10mm thick in cement mortar 1:4 on fair faces of ceiling finished even & smooth without using extra cement complete all as specified.

Supply only integral water proofing compound.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of 1 mm thick wall care putty of approved tint complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces & applying three coat of white wash on ceiling complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old decorated plastered surfaces of walls and applying one coat of cement base paint of approved shade/tint complete all as specified and directed by Engineer-in-Charge.

M&L complete removal of existing treatment on walls applying two coats of oil bound distemper over a coat of 1mm thick wall care putty complete all as directed.

M&L for preparation of old plastered surfaces of wall and applying one coats of white wash complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old plastered surfaces & applying one coat of white wash on ceiling complete all as specified and directed by Engineer-in-Charge.

M&L for providing precast cement concrete louvres and jallies, 25mm thick (measured solid), including all mouldings but excluding frame set in cement mortar set in cement mortar 1:4 (type B-0, 1:2:4) 12.5mm agregate complete all as specified and directed by Engineer-in-Charge.

Demolition mud in roofs, any thicknes, including plastering, existing tretement and cleaning (whether full thickness removed or only or part there of) etc in all respect and preparing it for further treatment and taking out and disposal of debris & rubbish to a distance exc 1 Km but not exc 1.5 Km complete all as specified and directed by Engineer-in-Charge.

M&L Cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) as in roof padding, laid to a minimum consolidated thickness of 25 mm as leveling course, laid and compacted in min slope 1:30 over roof complete all as specified and directed by Engineer-in-Charge.

M&L rendering 15mm thick in CM 1:4 with water proofing compound over green concrete surface(WPC will be measured and paid seperately) surface finished even and smooth (without using extra lime or cement) complete all as specified and directed by Engineer-in-Charge.

Preparation of roof top surface, providing and applying UV stable single component smart care damp proof ultra is a fibre reinforced elastomeric liquid applied water proofing membrane formulated with PU hybrid polymers and reinforcing acrylics fibre and having SRI of 106 on top of concrete roof surface in three coats incl self primer at ratio of damp proof and water 3:1 and coverage @ 1 Ltr/10 Sqm with a thickness of 650 micron. Note :- 6 Hrs interval between two coats will be maintain & the work will be carried out through company applicator duly get approved from Accepting officer in writing before incorpotion and paid only after receiving of the warrenty certificate from the company. Make:- Dr fixit, Asian paint or equivalent as approved by GE.

Cutting openings through walls for door, window and other openings or enlarging existing openings, etc., or cutting out defective masonry for underpinning including providing, fixing and removing, shoring, cleaning and stacking stone and removing surplus to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Forming jambs, etc., to openings (to foregoing item), with stone supplied by MES including cutting, toothings and properly bonding into old work built in CM 1:6, including facing and pointing (if necessary) to match existing work, complete all as specified and directed by Engineer-in-Charge.

M&L 50mm thick Sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates, etc, n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in cement mortar 1:4,complete all as specified and directed by Engineer-in-Charge.

Cutting holes in stone walls in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 exc half brick wall complete all as specified and directed by Engineer-in-Charge.

Taking down chowkats or frames not exc 1.5 sqm each complete all as specified & directed by Engineer-in-Charge.

Taking down chowkats or frames exc 1.5 sqm but not exc 4 sqm each complete all as specified and directed by Engineer-in-Charge.

M&L solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing in opening as per specification & drawing.

M&L for mild steel angle iron door frame/chowkats of Fe 410-0 (Gde-E-250 ) incl 12mm dia deformed bars for strengthing at bottom of chowkhats incl cutting floor at bottom to accommodated strengthing bars & making good the floor in PCC 1:2:4 type B-0 to match the existing floor complete all as specified and directed by Engineer-in-Charge.

S&F bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintel hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps,plate washers and similar small articles conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed by Engineer-in-Charge.

S&F 35mm thick 2nd class hard wood factory made panelled door shutter(two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. the size of rail and stiles as per IS: 1003 (part-I), kiln seasoned and chemically pressure treated and fixed to chowkats complete all as specified and directed by Engineer-in-Charge. Make : Pioneer, Surbhi metal, A-1 Teak.

S&F 35 mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed by Engineer-in-Charge. Make : Pioneer, Surbhi metal, A-1 Teak.

M&L factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified & directed by Engineer-in-Charge. Make : Rajshree/Engco/Sintex

M&L 25mm thick Prelaminated particle board, interior grade, prelaminated one side with deocrative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new wooden surfaces over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old wooden surfaces over 10cm width or girth and applying one coat of synthetic enamal paint (of approved shade) complete all as specified and directed by Engineer-in-Charge.

S&F butt hinges 100mm long medium weight, colled rolled mild steel complete all as specified and directed by Engineer-in-Charge.

S&F butt hinges 75mm long medium weight, colled rolledmild steel for Prelaminated doors complete all as specified and directed by Engineer-in-Charge.

S&F 150mm aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified & directed by Engineer-in-Charge.

S&F 150mm aluminium handles, cast type, anodised complete all as specified & directed by Engineer-in-Charge.

S&F 300mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified & directed by Engineer-in-Charge.

S&F 300mm helical/rat tail door spring 300mm size with MS sheet wing pattern including roller plate complete as directed by Engineer-in-charge.

S&F in repair stainless steel drapery rod 25mm dia (in lengths directed) of approved colour with and including decorative bowel at both ends and pair of power coated stainless steel brackets fixed at both ends with pvc Rawl plug and steel screwed on walls/beam complete all as specified & directed by Engineer-in-Charge.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanized wire staples complete all as specified and directed.

S&F in repair for pressed steel shutter 1mm thick including pressed steel frame of 1.25 mm thick sheet, 12mm dia MS rod for locking, two Nos chromium plated handle and one Godrej pattern lock including two coat of spray painting over a shop coat of primer, complete, all as shown in Drg No. TD/2004/29 sheet No. 1/3 to 3/3

S&F anodized aluminium frame and other sections for doors, windows, ventilators, partitions, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) with one or more rebates including joining cleat for fixing etc. complete all as specified & as directed.

S&F anodized aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as peg stays 150mm long (1 No.), hinges type B-21 100mm long (2 Nos), suitable handle (1 No.) complete all as specified & as directed.

S&F for powder coated (minimum thickness of powder coating 50 micron) anodised aluminium grill of approved pattern for windows/ ventilators/doors complete all as specified and directed.

S&F sheet glass ordinary quality, in squares not exc. 0.5 sqm each 4.80 mm thick complete as directed by Engineer-in-charge

S&F in repair kitchen sink without draining board made out of stainless steel 1mm thick with plugs, washers and waste pipe including bedding in cement mortar to dwarf wall or including and fixing cast iron cantilever brackets and connecting union to pipe over all size 495x420 mm bowl size 410x330x160 mm including flush pipe of polyethylene of low or high density or PVC 32mm bore with long screwed shanks and fly nuts complete all as specified & directed by Engineer-in-Charge. Make- Prayag/Parryware/Neelkanth

S&F stainless steel plate rack, 1.00mm thick for kitchen size 600mm x 900mm x 230mm complete all as specified & directed by Engineer-in-Charge. Make : Prayag / Parryware /Neelkanth.

S&F in repair PVC connection pipe, 15mm dia & 600mm long with adopter and washer at both end complete all as specified & directed by Engineer-in-Charge. Make : Prayag/Cera/Hindware.

S&F rotational moulded polyethylene water storage tanks of 500 Ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling water tanks complete all as specified and directed by Engineer-in-Charge. Make : Polycon/Sintex/Dhara.

S&F ball valves brass high pressure with polythelene float and fly net complete, screwed , iron pipes 20 mm dia complete all as specified & directed by Engineer-in-Charge. Make : Prayag/Cera/Hindware.

S&F brass gun-metal globe or gate valves 20mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Taking up or down 15mm steel tubing and connections, complete all as specified & directed by Engineer-in-Charge.

Taking up or down 20mm steel tubing and connections, complete all as specified & directed by Engineer-in-Charge.

S&F steel tubing medium grade 15mm bore with all fittings fixed complete to wall and or laid in floor complete all as specified & directed by Engineer-in-Charge. Make : Jindal/TATA/Appolo

S&F 20mm GI tubing medium grade fix to wall/floor complete all as specified & directed by Engineer-in-Charge. Make - Jindal/TATA/Appolo

S&F in repair fancy type 15mm dia bib taps, chromium plated alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule and fixed omplete all as specified & directed by Engineer-in-Charge. Make : Prayag/ Hindware /Cera.

S&F white vitreous china wash hand basin 'Flat back' of size 550x400mm fixed on and including new brackets CP waste coupling and PVC Waste pipe complete all as directed by the Engineer-in-Charge. Make : Cera/Hindware/Johson.

S&F 15mm dia CP pillar tap fancy type cast copper alloy, CP with capstan head, screwed ddown high pressure, with or without lettered 'HOT' or 'COLD' with long screwed shank and fly nuts screwed for iron pipe and fixed complete all as directed by the Engineer-in-Charge. Make : Prayag /Cera/ Hindware.

S&F in repair stop valve, fancy type, chromium plated alloy screwed down high presure, screwed both ends for iron pipe or for unions of 15 mm dia complete all as specified & directed by Engineer-in-Charge. Make :Prayag /Cera /Hindware.

S&F in repair stop valves, fancy type, chromium plated alloy screwed down high presure, screwed both ends for iron pipe or for unions of 15 mm dia long sunk concealed type complete all as specified & directed by Engineer-in-Charge. Make : Prayag /Cera /Hindware.

S&F Towel rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) complete all as directed by the Engineer-in-Charge. Make : Prayag/Cera/Hindware

Cutting holes into or through brick but in brick walls built, in cement mortar or cement lime mortar and stone walls built in lime mortar or walls of lime Ex 150 sq. cm but n exc 400 sq. Cm (not excluding 25CM depth) for cooler stand complete all as specified and directed by Engineer-in-Charge.

S&F in repair vitreous china squatting pan, Orissa pattern, size 580mm x 440mm white with integral foot rests connection to trap and to flushing pipe, etc.complete including making food to floor complete all as specified & directed by Engineer-in-Charge. Make : Parry ware /Hindware /Cera

S&F in repair PVC low level flushing cistern 10 liters capacity (white ISI marked) with inlet ball valve, float and handle, syphonic action type including brackets and flush pipe of polythelene of low or high density of PVC 32mm dia for LLFC complete all as specified. Make : Dolfine/Commander Champion

S&F in repair PVC (SWR) pipes 110 mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified & directed by Engineer-in-Charge.

S&F in repair PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints fixed to walls complete all as specified & directed by Engineer-in-Charge.

S&F in repair PVC (SWR) pipes 75 mm bore single socketed in any length with rubber ring joints fixed to walls complete all as specified & directed by Engineer-in-Charge.

S&F in repair PVC (SWR) bends any radius 110 mm bore complete all as specified & directed by Engineer-in-Charge.

S&F in repair Grating doom 100 mm dia of PTMT (Minimum weight 25 gms) fixed with cement complete all as specified & directed by Engineer-in-Charge.

S&F PVC (SWR) vent cowl 110mm complete all as specified & directed by Engineer-in-Charge.

S&F in repair 75mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified & directed by Engineer-in-Charge.

S&F in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified & directed by Engineer-in-Charge.

S&Fin repair PVC (SWR),110mm junction single, (Single T) equal or unequal complete all as specified & directed by Engineer-in-Charge.

M&L writing letters or figures(Block,roman,Italic or Indian letter n.exc 30cm high) complete as directed by Engineer-in-charge.

S&F brass chromium plated shower rose 125mm size with swivel joint type including fixing to steel pipe of 15mm bore or union complete all as specified.

M&L for angle or other section with gusset plates, rails, braces, stairs (framed) including stringers, treades, landing, balusters, hand rails confirming to FE 290 Gde E -165 etc, including cleats,brackets, etc complete all as specified & directed by Engineer-in-Charge.

S&F M.S. frame work such as grills/guard bars etc. with ends of bars, shouldered and or riveted or forged into spikes and similar works confirming to Fe-410-0 or Fe-310-0 including a coat of red oxide primer after preparation of steel surfaces complete all as specified.

Preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as directed by Engineer-in-charge and all as specified.

Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified & directed by Engineer-in-Charge.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified & directed by Engineer-in-Charge. Make : JSW/Tata Steel/RINL

Excavation in post holes each not exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exc 25cm, watering and removing surplush soil to a distance n exc 50m and making good surface complete all as directed by Engineer-in-charge and all as specified.

Excavation in trenches not exc 1.5m wide and not exc 1.5m deep for foundation or for shafts, walls, manholes etc not exc. 10 Sqm on plan and getting out in soft/loose soil.

M&L for PCC Type D2 1:4:8 (40 mm graded stone aggregate) Cement concrete in foundations, filling and mass-concrete complete all as specified & directed by Engineer-in-Charge.

M&L for PCC 1:3:6 type C1 using 20mm graded stone aggragate as in bed blocks, coping etc including weathering slightly rounded or chamfered angles and throating making grovves for fixing of man hole cover including necessary form work.

Returning filling in incl spreading levelling watering and well ramming in layers n.exc 25 cm in soft/loose soil complete all as specified & directed by Engineer-in-Charge.

Removal of excavated material (soil) to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above or below the starting point complete all as specified and directed by Engineer-in-Charge.

M&L concrete bed to drain pipes 150mm dia including packing under, and haunching against the sides of pipes after they are laid and tested; in PCC(1:4:8) type D2 (using 40 mm graded stone aggregate).

M&L salt-glazed stoneware drain pipes 150 mm dia laid in trenches and jointed as specified

M&L PCC(1:3:6) type C1 (using 20mm graded stone aggregates) in benching to manhole complete all as specified.

S&F for 50mm thick steel fibre reinforced (SFRC) manhole cover with iron frames (medium) complying to the standard specifications as mentioned in the IS 12592 BIS Standard minimum load bearing capacity 3 ton /Sqm in square rectangular or Circular shape complete all as specified and directed by Engineer-in-Charge.

M&L for 100mm thick PCC 1:4:8 type D -2 using 40 mm graded aggregate as in sub base of path/hardstanding complete all as specified & directed by Engineer-in-Charge.

M&L 60mm thick machine pressed precast conctete coloured interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 , M-35 Grade and over 25mm thick sand complete all as specified and as directed by Engineer-in-Charge.

M&L precast cement concrete solid block factory made in PCC 1:2:4 type B-1 using (20 mm graded stone aggregates) set in CM 1:6 (size of precast concrete block complete all as specified & directed by Engineer-in-Charge.

M&L sand for cushioning, interlocking tiles joint to be filled with sand, including spreading and levelling in layers n exc 25 mm thick complete all as specified and as directed by Engineer-in-Charge.

M&L rendering 5mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified.

Preparation of old steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as directed by Engineer-in-charge and all as specified.

Dismantling framed timber scantlings 40 sq. cm and over in section, in any position complete all as specified.

M&L for Roof trusses (framed), trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc. Fe 410 W (Gde E-250) Quality B ,complete all as specified & directed by Engineer-in-Charge.

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete & making good the floor in PCC 1:2:4 type B-0 to match the existing floor.Fe-410 (Gde-E250 quality A).

M&L flat iron hold fast 25mm x 6mm welded to angle iron door frame as directed by Engineer-in-Charge.

M&L plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe 410 W (Gde E-250) Quality B ,complete all as specified & directed by Engineer-in-Charge.

S&F for mild steel screw bolts dia of Neck 5mm to 10mm (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut,exc 5cm but not exc 10cm long compleete all as directed by Engineer-in-Charge.

M&L for cutting holes into or through but in stone walls built in cement mortar or cement lime mortar and walls of cement concrete. and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required superficial area not exc. 150 sqm cm for purlin, rafter compleete all as directed by Engineer-in-Charge.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified.

Surface excavation not exceeding 30 cm deep and averaging 15cm deep in soft/loose soil complete all as specified and directed.

Removing excavated materials (soils) exc 250m but not exceeding 500m and depositing where directed at a level not exceeding 1.50 km above the starting point.

M&L formwork to sides of concrete foundations, footings, bases of columns, sides and soffits (if any) of foundation and plinth beams and similar work; vertical or to batter for rough finished concrete surfaces complete all as specified and directed.

M&L formwork to sides of pillars, posts, struts, piers, columns and stanchions, square, rectangular or circular for rough finished surfaces of concrete complete all as specified and directed.

M&L form work to edges of concrete flats, treads, breaks in floor & roofs n.exc 20cm wide horizontal or sloping and similar works exc 10 cm but not exc 20cm wide for rough finished surfaces of concrete complete all as specified and directed.

M&L form work to chullah hoods, chajjas, troughs and similar items including edges for rough finished surfaces of concrete complete all as specified and directed.

M&L form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, etc for rough finished surfaces of concrete complete all as specified and directed.

M&L form work to soffits of slab, floor slab, landing and similar work etc n.exc 200mm thick (horizontal or sloping) for rough finished surfaces of concrete complete all as specified and directed.

M&L for RCC M-25 design mix using 20mm graded crushed stone aggregate in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc, basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for RCC M-25 design mix using 20mm graded crushed stone aggregate in column/ pillar and similar work complete all as specified and directed.

M&L for RCC design mix M-25 as in chhajjas complete all as specified and directed.

M&L for RCC design mix M-25 as in roof slabs supported on walls, beams & columns in floors etc.

M&L for reinforced cement concrete Design Mix M-25 as in roof beams, cantilevers, breassummers and lintels over 1.5m span complete all as specified and directed.

M&L broken stone hard core of gauge n.exc 63 mm, deposited spread and levelled in layer n.exc 15 cm thick watered and rammed to a true surface complete all as specified and directed.

S&F mild steel TMT bar 10mm dia and over, cut to length bent to shape reqd incl cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

All as per item No 135.00 above but 6 to 8mm dia.

M&L applying two coat of dry distemper tinted over a coat of alkali resistant priming paint on wall surfaces as directed by Engineer-in-Charge.

M&L for applying two coat of weather coat/apex paint (exterior emulision) of approved tint over new plastered surfacess scraping, sand papering or by any other mean and preparing plastered surfaces including one coat of primer on walls etc complete all as directed by Engineer-in-Charge.

M&L for padding & levelling course in 25mm thick PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) on roof & floor finished even & fair all as specified and directed.

M&L for anti-termite treatment to the bottom and sides of excavation at the rate of 5 liters of emulsion per square metre of surface area complete all as specified and directed.

M&L for anti-termite treatment to the top surface of filled earth at the rate of 5 ltrs of emulsion per square metre of surface area complete all as specified and directed.

M&L for anti-termite treatment to the soil under plinth protection at the rate of 5 liters of emulsion per square metre of surface area complete all as specified and directed.

M&L rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:3 surface all as specified and directed.

Supply only liquid water proofing compound.

S&F mild steel work confirming to Fe-290 or E-165 in hold fasts to flat iron cut to length, bend to shape incl preparing surfaces and trated with tar and sanded with clean sharp and complete as in hold fast wind etc complete all as specified and directed.

S&F factory made box type steel windows with side hung shutters incl box type hinges with steel handles & steel peg stay complete with glazing bars/dove talied welded incl fixing of lugs in PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) & marking good walls & cills to match the existing complete all as specified and directed.

All as per item No 146.00 above but without glazing bar.

M&L for 12mm thick perforated particle board/tiles for insulation and accoustic purposes, 60cm x 60cm in size, fixed with screws to iron frame work in ceilings, complete all as specified & as directed.

S&F anodized aluminium snap grid frame work for false ceiling, size of grid 605mm x 605mm including hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified & as directed.

S&F solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing given in SSR. Note :- PVC fillets & PVC strips shall be measured and paid for separately.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specifications and drawing given in SSR.

M&L for vitrified ceramic tiles 10mm thick (square/ rectangular), polished, coloured (light shade as approved) area of each tile not exceeding 0.36, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and directed.

M&L for vitrified ceramic tiles 10mm thick (square/ rectangular) (Ist quality), polished, coloured (light shade as approved), area of each tile exceeding 0.36 sqm , on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement & sand mortar 1:4 complete all as specified and as directed. Make : Kajariz/Johnson/Somany

Excavation over areas not exc 1.5m deep and getting out in soft/loose soil all as specified and as directed.

Excavation over areas exc 1.5m deep but not exc 3.0m and getting out in soft/loose soil all as specified and as directed.

Excavation over areas exc 3.0m deep but not exc 4.5m and getting out in soft/loose soil all as specified and as directed.

M&L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate in bedding to drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe all as specified and as directed.

M&L for 150mm bore reinforced concrete pipe, class NP2, laid and jointed (in CM 1:1) complete with collars,including taking down all as specified & as directed.

S&F salt glazed stone ware drain pipes of 150mm bore, grade `A’, ISI marked, laid to slope in trenches, jointed in CM (1:1) and tested complete all as specified.

M&L for precast cement concrete 1:2:4 type B1, using 20mm graded stone aggregate as in band coping, bed plate, benching etc including weathering, slightly rounded, chamfered angle and throating as directed including use and waste of form work (straight or curved) all exposed surface of concrete finished fair complete all as specified and as directed.

M&L for cement concrete (1:2:4) type B1 using 20 mm graded crushed stone aggregate as in surface channels and drains and benching including finishing the top of benching even and smooth using extra cement. Note : Forming fair finished channel for drain using extra cement shall be measured and paid for separately.

M&L PCC 1:5:10 type E2 using 40 mm graded stone aggregate in sunken filling, foundations, filling and mass concrete.

M&L for 100mm thick PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in flooring of septic tank finished even and smooth with using extra cement complete all as specified & as directed.

M&L precast RCC 1:2:4 type B1 using 20mm graded stone aggregate as in cover slabs of drains, manholes etc. including placing in position and set in CM (1:4) complete all as specified & as directed. Note :- Reinforcement shall be measured and paid for separately.

M&L for reinforced cement concrete 1:2:4 type (nominal mix) B1 using 20mm graded crushed stone aggregate in manhole/sock well/septic tank slabs/covers etc including necessary form work complete set in CM 1:6 complete as specifed.

M&L reinforced cement concrete (nominal mix) 1:2:4 type B1 using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like.

S&F 100 mm bore cast iron, sand cast soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, laid in trenches or floors complete all as specified.

S&F CI cowl for 100 mm bore CI pipe complete all as specified

S&F 75mm bore cast iron vent pipe with or without ears fixed to all complete all as specified

S&F 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified & as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc.

M&L loose filling with broken bricks aggregates of gauge 80 to 150 mm in soakage pits, soakage wells all as directed.

Cutting into existing manholes/septic tank for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required for 100mm bore pipe.

Taking down carefully copper/aluminium point wiring for one light/socket/power point and taking down of teak wood batten/ PVC casing caping and making good disturbed surfaces of walls/ ceiling/ floors etc including dismentling of fittings.

M&L for point wiring for one light point controlled by one, one way switch with 1.50 Sqmm two single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including PVC casing & caping with accessories fixed on surface of walls/ceiling by means of PVC sleeves/dash fasteners with cadmium plated screws, all as per IS and including wooden boxes fixed on wall with and including 3mm thick phenolic laminated sheet top cover for mounting switches, sockets, fan regulators etc complete all as specified.

All as per serial item No 175.00 here-in-before but for one fan/ceiling fan point controlled by one switch and regulator.

All as per serial item No 175.00 here-in-before but for one bell buzzer point controlled by one switch and regulator.

All as per serial item No 175.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board.

All as per serial item No 175.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board.

All as per serial item No 175.00 here-in-before but for one light point controlled by two, two way switches.

All as per serial item No 175.00 here-in-before but for one 3 pin socket outlet 15/16 Amps controlledby one 15/16 Amps switch on independent board with 2.50 Sqmm two single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour.

S&F switch piano flush type, single pole, one way, 5/6 Amp, 230 Volts complete all as specified and directed.

S&F switch piano flush type, single pole, one way, 15 Amp, 230 Volts complete all as specified and directed.

S&F switch piano flush type, single pole, two way, 5 Amp, 230 Volts complete all as specified and directed.

S&F socket outlet for 3 pin (with 2 pin outlet also), 5/6 Amp, flush type 240 Volt complete all as specified and directed.

S&F socket outlet for 2 in 1, 3 pin 5 & 15 Amp, flush type 240 Volt complete all as specified and directed.

S&F bell push flush type, 5 Amp 240 Volts complete all as specified and directed.

S&F bell/buzzer AC 230 Volts single pole complete all as specified and directed.

S&F ceiling rose surface Bakelite 65x50mm two or three terminals complete all as specified and directed.

S&F decorative ultra slim liner LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient suitable for 16 Watt to 20 Watt with LED tube 6000K of model E-LITE LED Pride Plus and connecting up with and including three core, PVC insulated, sheathed copper conductore cable of required size and length from ceiling rose to fitting complete all as specified & directed. Make : Havells Cat Part No LHEXBHP71NW018 or equivalent of Philips/ Crompton Greaves/Bajaj/Wipro.

S&F decorative ultra slim liner LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient suitable for 9 Watt with LED tube 6000K of model E-LITE LED Pride Plus and connecting up with and including three core, PVC insulated, sheathed copper conductore cable of required size and length from ceiling rose to fitting complete all as specified & directed. Make : Havells Cat Part No LUMILINEBS9WLED830SPCWH or equivalent of Philips/ Crompton Greaves/Bajaj/Wipro.

S&F in repair adore LED lamp 9/10 watt complete all as specified and directed. Make : Havell's/Crompton/ Syska.

S&F lamp holder PVC/Polycarbonatetype with back plate suitable forbatten fittings complete all as specified.

S&F stepped type electronic fan regulator, flush type and connecting up ISI marked 240 volts complete all as specified & directed.

S&F sheet metal enclosures, double door type, suitable for fixing MCB SPN with 200 Amps rated bus bar, 8 way, 240 volts complete all as specified and directed.

S&F sheet metal enclosures, double door type, suitable for fixing MCB TPN with 200 Amps rated bus bar, 4 way, 415 volts complete all as specified and directed.

S&F MCB 63 Amps, triple pole & neutral, 415 Volts complete all as specified and directed. Make : Legrand/Havells/ABB

S&F MCB 32 Amps, single pole & neutral, 240 Volts complete all as specified and directed. Make : Legrand/Havells/ABB

S&F MCB 6-32 Amps, single pole, 240 Volts 'C' curve, 10KA, ISI marked as per IS/IEC 60898-1 2002 complete all as specified and directed. Make : Legrand /Havells /ABB

S&F sub main wiring on including passing throuh PVC conduit pipe 1100 volts grade with PVC flexible cable copper conductor unsheathed multistranded single core of size 6 Sqmm and continuous earth with PVC flexible cable copper conductor unsheathed multistranded single core of size 4 sqmm of green colour confirming to IS 694/1990 including taking down existing unserviceable sub main wiring. (Note : Two runs of cable with one run of earth wire and one run of PVC casing caping should measured as one length).

S&F 2nd class hard wood rectangular block open recessed of size 60 x 45 x 5 cm depth with 3mm thick phenolic laminated sheet top cover fixed with suitable steel screws & PVC rawlplug(4 Nos), complete all as specified and directed.

S&F 2nd class hard wood rectangular block open recessed of size 30 x 25 x 5 cm depth with 3mm thick phenolic laminated sheet top cover fixed with suitable steel screws & PVC rawlplug(4 Nos), complete all as specified and directed.

S&F LED type security light luminaire 20 watt 230 V 50 Hz including all necessary fitting accessories and LED complete all as directed. Make Havells Superb Cat part No LHEXAYP7PN6K020 or equivalent of Philips/Crompton Greaves/ Bajaj/ Syska

S&F 1100 Volts grade heavy duty cable PVC insulated aluminium conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connection suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular of aluminium stranded conductors of size 10 Sqmm all as specified & directed.

Supply, laying, jointing and testing XLPE insulated, armoured, heavy duty LT underground electric cable with stranded aluminium conductor 1100 volts grade cross sectional area 25 sqmm 4 core laid in trenches, along poles through pipes etc complete all as specified & as directed. Note : (i) Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately including taking down old unserviceable XLPE cable. (ii) Road cutting/floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall be inclusive of the above provisions.

Supply, laying, jointing and testing XLPE insulated, armoured, heavy duty LT underground electric cable with stranded aluminium conductor 1100 volts grade cross sectional area 16 sqmm 2 core laid in trenches, along poles through pipes etc complete all as specified & as directed. Note : (i) Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately including taking down old unserviceable XLPE cable. (ii) Road cutting/floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall be inclusive of the above provisions.

M&L for brick work with fly ash bricks {As per IS-13757 (1993) burnt clay fly ash building bricks}, (Old size bricks) with width equal to the length of the brick laid dry & flat abutted with each other with gap between adjacent bricks not exc 10 mm over UG cable for protection complete all as specified & directed.

M&L dry sand (Tibba sand) and punning for cushioning to under ground cable all as directed. Note :- For the purpose of payment only punned thickness shall be measured.

M&L 40mm grade GI pipe (light grade) for protection of LT cable fixed to wall /pole /road crossing including clamps complete all as directed.

Disconnecting from elect connection and taking down carefully the existing electric energy meter of any capacity, any make, any size and depositing the same in AGE E/M Store Yard all as specified and directed by the Engineer-in-Charge. Refixing the same inside the old meter inside box carefully including necessary electric connections complete all as directed.

Disconnecting from elect connection and taking down carefully the existing ceiling fan/exhaust fan/geyser of any capacity any make, any size and depositing the same in AGE E/M Store Yard all as specified and directed by the Engineer-in-Charge. Refixing the same ceiling fan/exhaust fan/geyser carefully including necessary electric connections complete all as directed.

M&L for earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/ Test point /panel / equipment and testing on including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 3.00 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, PCC chamber (1:3:6) type C1, 40mm thick precast RCC cover 1:2:4 type B1 shall be provided on CI frame etc complete all as specified & as directed.

S&F exhaust fan 300mm sweep 240 volts AC including provision of hole in wall of suitable size for fixing of exhaust fan all as directed by Engineer-in-Charge. Make : Havells / Crompton / Bajaj/Orient.

S&F ceiling fan 5 star rating complete of 1200mm sweep 240 volts AC including provision of hook in ceiling of suitable size for fixing incl neessary electric connection all as directed by Engineer-in-Charge. Make : Havells / Crompton / Bajaj/Orient

M&L earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron 32mm x 6mm earth lead strip by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part I and connection to machinery/ equipment / main switch board or panel and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, PCC chamber (1:3:6) type C-2, charcoal and salt mixed layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 40 mm bore 3.00 metre long GI pipe light grade for earth lead strip protection, 75 mm thick RCC cover 1:2:4 type B-1 shall be provided on CI frame etc complete all as specified & as directed.

Fixing only Air cooled split unit air conditioner electric driven single phase of capacity 2 TR and connecting up all as per manufacturer’s instructions & as directed. Note :- (i) Air cooled split unit air conditioner electric driven single phase of capacity 2 TR shall be issued under Schedule ‘B’ free for fixing only. (ii) Cost of cutting chases/cutting holes etc in walls/floors including making good in cement mortar 1:4, M&L for covered shed for out door unit of AC made out & fabricated with MS angle iron 40x40x6mm, MS plain black sheet 0.63mm thick, wire mesh etc with provision of front openable shutter and locking arrangement including painting on all steel and iron surfaces with two coat of synthetic enamel paint over a coat of red oxide primer complete including PCC platform, other necessary arrangement for fixing indoor & outdoor unit & other minor extras shall be deemed included in quoted rate of this item.

S&F MCB SPN 40 Amp in the existing DB including making electrical connection and testing complete all as specified and directed. Make : Legrand/Havells/Standard.

M&L sub main wiring with two runs of 4 sqmm (nominal area) size main cable & one run of 2.5 sqmm size earth continuity conductor, single core, PVC insulated, unsheathed, FRLS with multi-stranded copper conductor, 1100 Volts grade, ISI marked (IS: 694) cable, drawn through & including suitable size of PVC casing & capping ISI marked not less than 40mm width & with accessories, fixed on surfaces of wall/ceiling complete. Note:- 02 runs of 4 sqmm size, 01 run of 2.5 sqmm size cable & PVC casing & capping with accessories shall be measured as one run length for payment purpose.

Supply, installation & testing geyser (water storage type) 5 star rated, energy efficient of capacity 25 litre vertical mounting type, suitable for 230V, SP, 50 Hz AC supply fixed with & including ‘Anchor’ type /fastener type bolts & nuts (Set of 4 bolts of 10mm dia 150mm long with nuts & washers) into the wall grouted properly to hold the geyser and making good the disturbed surface as original all as per manufacturer’s instructions & as directed. Make : Bajaj /Crompton Greaves/Usha Lexus/Racold.

S&F metal clad plug and socket board SP&N enclosure with 2 pole and earh metal plug and socket complete with 20 Amp MCB SP 'C' curve complete.

S&F 15mm dia bib tap, cast copper with crtuch or butterfly handle, complete all as specified & directed by Engineer-in-Charge. Make : Prayag/Hindware/Cera

S&F 15mm dia stop valve, cast copper screwed down, high pressure with crtuch or butterfly handle, complete all as specified & directed by Engineer-in-Charge. Make : Prayag /Hindware/Cera

S&F PVC connection, 15mm size with PTMT nuts of length 450mm complete all as specified & directed by Engineer-in-Charge.

M/S Naglot Enterprises

M/s Laxmi Enterprises

shiva construction

AARSINFRATECH

M/s S Amarjit Singh