COMPLETION OF LEFT OVER WORK IN RESPECT OF CA NO GE/EM/LKO/HOSP/72 OF 2024-2025 REPAIR / MAINT TO ROOF SHEET ROOF TREATMENT JOINERY FLOORING BOUNDARY WALL FENCING DRAIN MECHANIZED PERIODICAL SERVICES AND SEWAGE DISPOSAL AND MISC B/R WORKS AT

Demolition of brick work or stone / boulder masonry built in cement mortar or cement lime mortar including all quions, arches, pillars etc but excluding ashlar facings, dressed stone work and pre cast concrete articles complete all as specified and directed.

M&L for Brick work with Fly ash brick designation 100 Kg / Sqcm, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6, using bricks of size 230 mm x 110 mm x 70 mm confirming to IS 12894, complete all as specified and as directed by Engineer-in-Charge.

M&L for Brick work in half brick thick wall with Fly ash brick designation 100 Kg / Sqcm, straight or curved on plan exc 6 m mean radius built in cement mortar 1:4, using bricks of size 230 mm x 110 mm x 70 mm confirming to IS 12894, complete all as specified and as directed by Engineer-in-Charge.

M&L for 15mm thick rendering on brick work or concrete surfaces in CM 1:6 finished fair & even without extra cement, cement mortar complete all as specified.

M&L Preparation of newly plastered or unplastered surfaces of walls and applying two coats of cement base paint complete all as specified and directed by Engineer-in-Charge

Demolition of cement concrete (un-reinforced) in ground floors and paving n. exc 15 cm thickness (below or above ground level) including removal of debris up to 1.50 Km complete all as specified and directed by Engineer-in-Charge

M&L for 40 mm thick PCC type B-1 1:2:4 ( 20mm graded agg) as in flooring, finished even and smooth with using extra cement all as specified and as directed.

M&L 75 mm thick cement concrete 1:3:6 type C2 (using 40 mm graded stone aggregate) as plinth protection/path and the like complete all as specified and directed by Engineer-in-Charge

M&L for filling joints between two panels with mix of 85/25 bitumen and sand in 1:3 complete all as specified and directed by Engineer-in-Charge

M&L for plain cement concrete 1:2:4, type B-1 using 20 mm graded stone aggregate as in coping, and bed block, wall through and the like including weathering slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed.

M&L for Hardcore of broken stone or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

Taking down cement plaster on brick wall, racking out joints hacking for key scrubbing down with water complete all as specified and directed by Engineer-in-Charge

M&L for rendering 10 mm thick on brick work/ concrete surfaces in cement mortar 1:6 on fair faces finished fair & even complete all as specified and directed by Engineer-in-Charge

M&L for 15 mm thick rendering in CM 1:4 on fair faces of brick work surface finished even and fair without using extra cement complete all as specified and directed by Engineer-in-Charge (Note : Integral WPC shall be measured and paid seprately )

M&L rendering 5 mm thick on concrete surfaces in ceiling , in cement and sand mortar 1:3 complete all as specified and directed by Engineer-in-Charge

Supply only Liquid water proofing compound.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper (first Quality) over one coat of primer over and including 2 mm to 3 mm thick cement base wall care putty complete all as specified and directed by Engineer-in-charge.

M&L for preparation of new plastered surface of walls and applying two coats 100% Premium acrylic emulsion exterior paint over one coat primer including 1 mm thick exterior grade wall care putty complete all as specified and directed. Make Apex (Asian Paint) / Weather coat (Berger) / Excel Top Guard (Nerolac)

M&L for preparing surfaces, plastered or unplastered new surfaces of ceiling and applying three coats white wash complete all as specified and directed by Engineer-in-Charge

Demolition of existing roof treatment of any type, including screed bed etc complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate, (Avg 50 mm thickness) in roof for padding to achieve the 1:40 slope complete all as specified and as directed.

M&L for 15 mm thick screed bed in cement mortar 1:4 over RCC roof slab including mixing only water proofing compound as per manufacturer instruction complete all as specified and directed by Engineer-in-Charge. (WPC will be measured and paid separately)

M&L for water proofing treatment on roof surfaces in the following manner:- (a) The surfaces shall be painted with hot bitumen grade 30/40 confirming to IS-73 @ 1.20 kg / sqm over a coat of bituminous primer conforming to IS-3384 @ 0.30 ltr /sqm. (b) Supply & lay 3 mm thick APP water proofing membrane reinforced with non woven polyester matt laid using bitumen torch by torch application with a side lap of 10 cm & 15 cm end lap weighing not less than 3.5 kg / sqm. Note: - (i) Work to be carried out through authorised applicators of the manufactures and work will be carried out in complete / in patches in roofs (ii) Contractor shall submit written guarantee of 07 (Seven) years from date of completion & submit security deposit @ 2.5% of executed amount or Rs 6250.00 which ever is more.

M&L for preparation of untreated surface of APP membrane of any description over 10 cm in width or girth, not otherwise described and applying two coat of aluminium paints over one coat primer complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M&L for premium / 1st quality non skid ceramic coloured tiles of size 300 mm x 300 mm x 7-8 mm thick as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles laid over and including 15 mm thick screed in CM 1:6 complete all as specified and directed by Engineer-in-Charge. Note : Quoted rate shall be deemed to include cast of screed bed.

M&L premium / 1st quality coloured glazed ceramic tiles (digital printed) in vertical surfaces of size 300 mm x 450 mm x 7-8 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the tiles, laid over and including 10 mm thick backing coat in CM 1:3 complete all as specified and directed by Engineer-in-Charge. Note : Quoted rate shall be deemed to include cast of backing coat.

M&L for 18-20 mm thick machine cut Kota stone slab flooring with marble stone strips / slab / tiles as per design approved, laid over and including cement screed bed 20 mm thick in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, & polishing complete all as specified and directed.

M&L for 18-20 mm thick machine cut Kota stone slab as in skirting /riser laid over and including backing coat 10 mm thick in CM 1:3, and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified and directed.

Deployment of man power & floor grinding machine for grinding and polishing of existing Kota stone / terrazzo tiles flooring, polished up to mirror finish complete all as specified and directed

M&L for 75 mm thick plain cement concrete type D- 2, 1:4:8 (40 mm graded aggregate) complete all as specified and directed.

M&L For chequered cement concrete tiles 30 cm x 30 cm x 25 mm thick with white cement and pigment, set, jointed and pointed in neat cement slurry laid over and including 20 mm thick screed bed in CM 1:4 as in floors / path complete all as specified. Note : Screed bed will not be measured and paid separately)

Demolition of interlocking paver block of any description or thickness in path / hardstanding etc laid, bedded and pointed dry, including removal of sand screed all as specified.

Fixing / Laying only 60 mm thick PCC paver block of any description / pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., laid over and including 20 mm thick compacted bed of fine sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, using paver block retrieved from demolition, complete all as specified and directed.

M&L for Providing and laying 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., made by table vibratory method using PU mould, laid in required pattern over and including 20 mm thick compacted bed of fine sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

Taking down chowkhat or frames (wooden / aluminium / iron) with shutters (without taking off shutters from the frames) not exc 1.50 Sqm each complete all as specified and as directed by the Engineer-in-Charge

Taking down chowkhat or frames (wooden / aluminium / iron) with shutters (without taking off shutters from the frames) exc 1.50 Sqm but n exc 4.00 Sqm each complete all as specified and as directed by the Engineer-in-Charge.

Taking down shutters of any description area n exc 1 Sqm each complete all as specified and directed.

Taking down shutters of any description area exc 1 Sqm and n exc 2 Sqm each complete all as specified and directed.

S&F plain solid, straight chowkhat & frames of 2nd class HW (Hollock) wrought, framed rebated on the solid, rounded or chamfered, put together with glue & pinned at joints including preparation of back of chowkats & treated with coal tar complete all as specified and directed.

S&F Mild steel work Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 as in small articles like angle iron framing work for manhole, rungs/steps in man hole, complete all as specified and directed.

M&L for plain cement concrete 1:3:6, type C-1 (using 20 mm graded stone aggregate) for embedding holdfast, bed block, cills, etc including necessary formwork complete all as specified and directed by Engineer-in-Charge

M&L for preparing new steel surfaces of small articles like MS rungs etc and treating with coal tar black paint, area tarred not exc 0.1 sqm, each complete all as specified and directed.

S&F 30 mm thick flush door shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as directed.

S&F 30 mm thick 2nd class hard wood Glazed and Skelton shutter, open rebated and prepared to receive glass, gauge etc. divided into squares with plain chamfered or rounded, mitred and rebated sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.23(b) complete all as specified and directed.

S&F 25 mm thick second class hardwood glazed shutters as in windows/vertilators open rebateed and prepared to received mitred aand secured sash bars any numbers edges of fsdraming plain chamfered of rounded in SSR Part I Section 8 caluse 8.24 (b).complete all as specified and directed by Engineer-in-Charge

M&L for preparation of new wood and wood based surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint (first Quality) over a coat of pink primer complete all as specified and directed.

S&F steel windows with side hung shutters including hinges with steel handle, and steel peg stay, complete with and including both glazing and gauge shutters to receive glass and wire mesh, dovetailed or welded complete all as specified and directed.

S&F Steel windows or ventilators, fixed type, with glazing bars complete all as specified and directed.

S&F for anodised aluminium frame for doors, windows, ventilators, partition section with one or more rebates including joining cleat for fixing etc. complete all as specified.

S&F for anodised aluminium work for doors, windows any type sliding or fixed, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. complete all as specified.

S&F in repairs aluminium anodized grill weight of 3.13 Kg per Sqm (min) with suitable aluminium anodized frame of F/H section of 0.297 Kg per Meter (min) with suitable fixing screws / attachment etc complete all as specified and directed.

S&F PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing in opening complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as shown in drawing of relevant item in MES, schedule Part-II , 2020 as specified and as directed by Engineer-in-Charge.

S&F for Steel rolling shutters, thickness of laths 1.25mm, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type including taking down of old rolling shutters complete all as specified and directed by Engineer-in-Charge

S&F 75 mm size butt hinges medium weight cold rolled mild steel complete all as specified and directed by Engineer-in-Charge

S&F 100 mm size butt hinges medium weight cold rolled mild steel complete all as specified and directed by Engineer-in-Charge

S&F 100 mm size Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed by Engineer-in-Charge

S&F 150 mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engineer-in-Charge

S&F Aluminium anodised sliding door bolt 300 m long, with hasp, staple (bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, 300 mm long, mild steel, rat tail rod pattern springs including roller and roller plates complete all as specified and directed by Engineer-in-Charge

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm in steel window clips and wooden beading in wooden joinery complete all as specified and directed.

S&F in repair galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm in steel window clips and wooden beading in wooden joinery complete all as specified and directed.

Hacking out old broken glass (any thickness size, quality or description) from wooden frames or stone, concrete or bricks round, glazed with putty or fixed with bedds complete all as specified and directed by Engineer-in-Charge

S&F 3 mm thick sheet glass , ordinary quality and glzing with oil putty/timber bedds in square n. exc. 0.50 sqm in each pane complete all as specified and directed by Engineer-in-Charge

S&F for 3.0 mm thick figured glass ordinary quality and glazing with oil putty n.exc 0.5 Sqm each pane

S&f for 4.8 mm thick sheet glass odinary qulity and glazing with neosprene beading n.exc 0.5 Sqm in each pane

Taking up or down steel tubing and connections of 15 mm bore complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connections of 20 mm bore complete all as specified and directed by Engineer-in-Charge.

M&L 15 mm nominal bore Mild steel galvanised water tubing , medium grade , with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge.

M&L 20 mm nominal bore Mild steel galvanised water tubing , medium grade , with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge.

Dismantling water tank capacity exc 250 & n.exc 500 ltr and taken as credit

Supply and fix 500 litres capacity double layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc complete.

S&F in repair ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball , suitable for 20 mm bore pipe, screwed for iron pipe and fixed. .(Minimum weight 20mm-210gms) complete all as specified.

S&F in repairs cast copper alloy, chromium plated, fancy type long body Bib taps with with capston handle, screwed for 15 mm bore dia. iron pipe or for brass ferrule and fixed complete all as specified.

S&F in repair 15 mm size Angle valve, cast copper alloy, chromium plated, fancy type with capstan head, with screwed down, screwed both end for iron pipes complete.

S&F in repair 15 mm size pillar taps, cast copper alloy, chromium plated, fancy type, with capstan heads, screwed down high pressure, with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-charge.

S&F in repairs PTMT( Polytetra Methyllene Terephthalate ) Bib taps suitable for 15 mm bore pipe standard of PTMT any colour screwed, for iron pipe and fixed ( Minimum weight 15 mm-90 gms complete all as specified .Make : Prayag or Shakti

S&F in repairs stainless steel chromium plated gratings suitable for 75 / 100 mm dia NT/ FT complete all as specified.

Supply and fix in repairs white vitreous china squatting pan ‘ORISSA’ pattern of size 580 mm x 450 mm white with integral foot rests with ‘P’ or ‘S’ trap, front or back inlet including all connection and provision of lime concrete base complete all as specified and as directed.

Supply and fix in repairs 10 Litre capacity PVC symphonic action type flushing cistern (ISI Marked) low level with inlet ball valve, float and handle & PVC flush pipe, fixed in position and connecting complete.

S&F in repair PVC connection 15 mm size with PTMT nut, length 450 mm complete.

S&F in repair vitreous china wash basin (WHB) , white , flat back , size 550mmx400mm including brackets, waste fittings , brass Chromium plated for glazed basins etc. embedded in red lead cement, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified.

S&F 32mm bore flexible pipe of PVC fixed to WHB/ urinals as waste pipe ( not less than 600mm) including PVC coupling complete all as specified.

S&F in repair cast iron floor trap with chromium plated grating including jointing to waste pipe wih cement mortar (75 mm bore of pipe).

Taking down pipes (any sizes) including all fittings, complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, or fixed to wall

Dismantling post or struts (wood/steel or RCC) any section incl taking out embedded portion and making good distrubed on normal ground in concrete, brick works masonary complete all as specified and directed.

Excavating in post holes each not exc. 0.5 cum getting out in soft / loose soil, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exc. 25 cm, watering and removing surplus soil to a distance not exc. 50 m and depositing where directed

S&F for angle iron as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing ire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165, complete all as specified and directed.

M&L for PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

S&F steel work in tubular trusses, posts, purlins & rafter including special washers etc complete using ERW or induction butt welded tubes conforming to I.S. 1161-1998 grade St-240, complete all as specified and directed.

S&F Framed work such as grills, gratings, etc. with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290, Gde-E-165

Dismantling of roof sheet (any descriptions) including ridges in roof covering complete all as specified and directed.

S&F for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof overing/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for dismantling fencing wire mesh any type complete all as specified and directed.

Fixing only chain link fencing of description fixed to steel post with mild steel flat & nut bolt etc. Note: (i) Supply only fencing, will be measured and paid separately. (ii) Supply and fix mild steel nut bolt, line wire and flat will be measured and paid separately.

Supply only chain link fencing made out of mild steel galvanised wire of size & aperture approved by the Engineer - in - Charge, conforming to IS 2721 all as specified & directed. Note:- Fixing only fencing will be measured and paid separately.

M&L for preparing new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint (first Quality) over one coat of red oxide primer complete all as specified.

Taking down Galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs complete all as directed.

S&F for Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. complete all as specified and directed. (Note :- Each line wire to be measured)

Restraining / resecuring including making good staples galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2 mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossings with and provn of galvanised mild steel wire, staples or steel pins etc. complete all as specified and directed. NOTE: Each line wire to be measured.

Preparation of old decorated plastered or unplastered surfaces of walls by brooming down or steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts, trading oil and greasy spots and applying one coat of white wash complete all as specified and directed by Engineer-in-Charge

M&L for Preparation of Old decorated surfaces of ceiling including cleaning brooming down or with steel wire brushing, scrapping down smooke soot, moulds, moss and efflorescent salts cleaning oil and geasy spots, trading oil, greasy spots etc and applying one coat of white wash complete all as specified and as directed.

Preparation of old plastered or unplastered surfaces of walls by washing, rubbing down & stopping etc, and applying one coat of cement base paint of any tint/shade complete all as specified and directed by Engineer-in-Charge

M&L preparation of old painted surface of walls and applying one coat 100% Premium acrylic emulsion exterior paint of any tint / shade complete all as specified and directed. Make: Apex (Asian Paint) / Weather coat (Berger) / Excel Top Guard (Nerolac)

M&L for complete removal of existing treatment of wall / roof projections including facia, cornices etc by scrapping with mechanical sander (having mechanical vacuum mechanism) with sanding pad of appropriate grit to make surface clean, free from dust, loose paint etc by skilled labour and applying 2 mm thick wall care putty, two coats of oil bound distemper (first Quality) of any tint / shade over one coat primer complete all as specified and directed.

M&L for preparation of old painted wood and wood based surfaces of any description, not otherwise described over 10 cm width or girth, including knotting and stopping holes and applying one coat of synthetic enamel paint (first Quality) complete all as specified and directed by Engineer-in-Charge

M&L for preparation of old painted surfaces of steel of any description, not otherwise described over 10 cm width or girth,and applying one coat of synthetic enamel paint (first Quality) complete all as specified and directed.

Deployment of manpower & tools etc for Complete removal of existing treatment on wall / roof projections including facia, cornices etc by scrapping with mechanical sander (having mechanical vacuum mechanism) with sanding pad of appropriate grit to make surface clean, free from dust, loose paint etc by skilled labour complete all as specified and directed. (Rate included for necessary scaffolding and arrangement for working up to 15 mtrs height).

M&L for applying minimum 1 mm thick exterior grade wall care putty over prepared plastered wall surface to achieve the surface even and smooth for application of painting complete all as specified and directed. Note:- Rate included for necessary scaffolding and arrangements for working up to 15 m height and working on any type of roof like AC sheet, Galvalume sheet with necessary safety measures.

M&L for applying two coats of 100% Premium acrylic emulsion, exterior paint on wall surfaces, having VOC less than 50 gm / litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of approved shade (Company Depot tinted) with silicon additives over and including priming coat of exterior primer complete all as specified and directed.