Special repair of Furniture (Wooden/Steel) at MFFR under GE (N) Bikaner

Amount

Material & Labour for removing carefully existing broken / unserviceable components/members of Table Writing (Steel) (900 x 600 x 760 mm) and supply & fixing following new components/members duly finished complete all as shown on drawing, specified and directed :- Drg No. TP

Table top made of 18mm thick prelaminated particle board (Exterior grade) one side decorative of approved shade of size 900 x 600 mm fixed with screws with & including 4mm thick half round teak wood edging fixed alround to top. Notes : (i) Table top shall be provided in single piece. (ii) French polish with high gloss finish shall be provided to exposed wooden surfaces of teak wood edging. Drg No. TP

PVC shoe of best quality conforming to sample kept in GE’s office. Drg No. TP

Replacing damaged portion of leg with new 25mm square mild steel tube of 1.6mm wall thickness, 10cm in length by cutting the damaged portion with hacksaw & fixing of new tube to leg by gas welding including applying one coat of synthetic enamel paint of approved tint over a coat of red oxide zinc chromate primer on new pipe and one coat of paint on portion disturbed during welding complete all as shown on drawing, specified and directed. Drg No. TP

Repair to drawer of the table by removing deep dents, welding of broken joints etc. complete to make it fully functional with & including applying one coat of synthetic enamel paint over a coat of red oxide zinc chromate primer on welded joints. Drg No. TP

Painting to all steel surfaces of the Table Writing with one coat of synthetic enamel paint of approved tint with spray machine after preparation of old painted surfaces. Drg No. TP

Material & Labour for removing carefully existing broken / unserviceable components/members of Table Writing (1145 x 600 x 760) and supply & fixing following new components/members duly finished complete all as shown on drawing, specified and directed :- Drg No. FD-249 & FD-275

Table top made of 18mm thick prelaminated particle board (Exterior grade) one side decorative of approved shade of size 1145 x 600 mm fixed with screws with & including 4mm thick half round Shisham wood edging fixed alround to top. Notes : (i) Table top shall be provided in single piece. (ii) French polish with high gloss finish shall be provided to exposed wooden surfaces of Shisham wood edging. Drg No. FD-249 & FD-275

Cabinet of table. Drg No. FD-249 & FD-275

Drawers of table. Drg No. FD-249 & FD-275

Shutter of table of size 570mm x 405mm made out of 18mm thick prelaminated particle board including piano type hinges 40mm wide and knob. Drg No. FD-249 & FD-275

Leg of table of 1st class shisham wood of size 45 x 45 x 750mm. Drg No. FD-249 & FD-275

Foot rest of table of 1st class shisham wood of size 50 x 25 x 1025mm. Drg No. FD-249 & FD-275

Aluminium anodized knob 25mm of best quality. Drg No. FD-249 & FD-275

Lock of brass multipurpose 4 lever with duplicate key size 40 mm. Drg No. FD-249 & FD-275

Second class hard wood corner / bracket (L shape) of size 100 x 100 x 25 mm thick and fitted with screws between long rail to legs & short rail to legs. Drg No. FD-249 & FD-275

French polish two coats to achieve high gloss finish to Table Writing including preparation of surfaces by removing old polish by scraping & rubbing with suitable sand paper, filling putty wherever required and making the surfaces smooth complete all as specified, shown on drawings and as directed. Drg No. FD-249 & FD-275

Material & Labour for removing carefully existing broken / unserviceable components/members of Table Dining Steel Frame of size 1800mm x 750mm and supply & fixing following new components/members duly finished complete all as shown on drawing, specified and directed :- Drg No. TP

Table top made of 18mm thick prelaminated particle board (Exterior grade) one side decorative of approved shade of size 1800 x 750 mm fixed with nut & bolts of size of 4mm dia & 50mm long with & including 4mm thick half round teak wood edging fixed alround to top. Notes : (i) Table top shall be provided in single piece. (ii) French polish with high gloss finish shall be provided to exposed wooden surfaces of teak wood edging. Drg No. TP

PVC shoe of best quality conforming to sample kept in GE’s office. Drg No. TP

Replacing damaged portion of leg with new 25mm square mild steel tube of 1.6mm wall thickness, 10cm in length by cutting the damaged portion with hacksaw & fixing of new tube to leg by gas welding including applying one coat of synthetic enamel paint of approved tint over a coat of red oxide zinc chromate primer on new pipe and one coat of paint on portion disturbed during welding complete all as shown on drawing, specified and directed. Drg No. TP

Painting to all steel surfaces of the Table Dining with one coat of synthetic enamel paint of approved tint with spray machine after preparation of old painted surfaces. Drg No. TP

Material & Labour for removing carefully existing broken / unserviceable components/members of Peg Table Steel and supply & fixing following new components/members duly finished complete all as shown on drawing, specified and directed :- Drg No. TP

Table top made of 18mm thick prelaminated particle board (Exterior grade) one side decorative of approved shade of size 450 x 300 mm fixed with screws with & including 4mm thick half round teak wood edging fixed alround to top. Notes : (i) Table top shall be provided in single piece. (ii) French polish with high gloss finish shall be provided to exposed wooden surfaces of teak wood edging. Drg No. TP

PVC shoe of best quality conforming to sample kept in GE’s office. Drg No. TP

Painting to all steel surfaces of the Peg Table with one coat of synthetic enamel paint of approved tint with spray machine after preparation of old painted surfaces. Drg No. TP

Material & Labour for removing carefully existing broken / unserviceable components/members of Peg Table (450 x 300 x 380) and supply & fixing following new components/members duly finished complete all as shown on drawing, specified and directed :- Drg No. FD-277

Table top made of 18mm thick prelaminated particle board (Exterior grade) one side decorative of approved shade of size 450 x 300 mm fixed with screws with & including 4mm thick half round teak wood edging fixed alround to top. Notes : (i) Table top shall be provided in single piece. (ii) French polish with high gloss finish shall be provided to exposed wooden surfaces of teak wood edging. Drg No. FD-277

Front and back rail made of Teak Wood. Drg No. FD-277

Short rail made of Teak Wood. Drg No. FD-277

Legs square / round type made of Teak Wood. Drg No. FD-277

Short/long stiffeners made of Teak Wood. Drg No. FD-277

Second class hard wood corner / bracket (L shape) of size 50 x 50 x 20 mm thick and fitted with screws between long rail to legs and short rail to legs. Drg No. FD-277

French polish two coats to achieve high gloss finish to Peg Table including preparation of surfaces by removing old polish by scraping & rubbing with suitable sand paper, filling putty wherever required and making the surfaces smooth complete all as specified, shown on drawings and as directed. Drg No. FD-277

M&L for opening up and removal of seat, back and shoes of Chair Dining steel, preparation of old painted steel surfaces and painting by applying one coat of synthetic enamel paint of approved tint with spray machine and re-fixing of serviceable seat/back/shoes & replacing the unserviceable seat/back/shoes with & including new steel nut and bolts, welding of frame where required etc complete all as specified, shown on drawings and as directed. Notes : (i) The seat, back & shoes to be replaced shall be paid separately under respective serial item No. 6.01 to 6.03 here-in-after as supply only. (ii) Old steel nut & bolts shall not be used. The cost of new steel nut and bolts shall be deemed to be included in the quoted rates of this item. Drg No. TP

Supply only seat of size 405 x 430 mm made of 18mm thick prelaminated particle board (Exterior grade) with & including beading with 4mm thick half round teak wood alround for repair to chair under serial item No. 6 here-in-before complete all as specified and as directed & conforming to sample kept in GE’s office. Drg No. TP

Supply only back of size 405 x 250 mm made of 18mm thick prelaminated particle board (Exterior grade) with & including beading with 4mm thick half round teak wood alround for repair to chair under serial item No. 6 here-in-before complete all as specified and as directed & conforming to sample kept in GE’s office. Drg No. TP

Supply only PVC shoe of best quality as shown on drawing for repair to chair under serial item No. 6 here-in-before complete all as specified and as directed & conforming to sample kept in GE’s office. Drg No. TP

Material & Labour for removing carefully existing broken / unserviceable components/members of Chair Dining and supply & fixing following new components/members duly finished complete all as shown on drawing, specified and directed :- Drg No. FD-279

Rear leg made of Teak Wood. Drg No. FD-279

Front leg made of Teak Wood. Drg No. FD-279

Front rail made of Teak Wood. Drg No. FD-279

Back rest made of Teak Wood. Drg No. FD-279

Side rail made of Teak Wood. Drg No. FD-279

Back rail made of Teak Wood. Drg No. FD-279

Stiffener (one large piece and two small piece) made of Teak Wood. Drg No. FD-279

French polish two coats to achieve high gloss finish to Chair Dining including preparation of surfaces by removing old polish by scraping & rubbing with suitable sand paper, filling putty wherever required and making the surfaces smooth complete all as specified, shown on drawings and as directed. Drg No. FD-279

M&L for opening up and removal of seat, back, handle and shoes of Chair Writing steel with arms, preparation of old painted steel surfaces and painting by applying one coat of synthetic enamel paint of approved tint with spray machine and re-fixing of serviceable seat/back/handle/shoes & replacing the unserviceable seat/back/handle/shoes with & including new steel nut and bolts, welding of frame where required etc complete all as specified, shown on drawings and as directed. Notes : (i) The seat, back, handle & shoes to be replaced shall be paid separately under respective serial item No. 8.01 to 8.04 here-in-after as supply only. (ii) Old steel nut & bolts shall not be used. The cost of new steel nut and bolts shall be deemed to be included in the quoted rates of this item. Drg No. TP

Supply only seat of size 535 x 470 mm made of 18mm thick prelaminated particle board (Exterior grade) with & including beading with 4mm thick half round teak wood alround for repair to chair under serial item No. 8 here-in-before complete all as specified and as directed & conforming to sample kept in GE’s office. Drg No. TP

Supply only back of size 470 x 250 mm made of 18mm thick prelaminated particle board (Exterior grade) with & including beading with 4mm thick half round teak wood alround for repair to chair under serial item No. 8 here-in-before complete all as specified and as directed & conforming to sample kept in GE’s office. Drg No. TP

Supply only handle of chair writing of size 400 x 60 mm made of 18mm thick plywood with decorative laminated sheet 1.2 mm thick fixed with 4mm dia bolt & nuts with smooth finished edging for repair to chair under serial item No. 8 here-in-before complete all as specified and as directed & conforming to sample kept in GE’s office. Drg No. TP

Supply only PVC shoe of best quality as shown on drawing for repair to chair under serial item No. 8 here-in-before complete all as specified and as directed & conforming to sample kept in GE’s office. Drg No. TP

M&L for opening up and removal of seat, back, handle and shoes of Chair Easy steel, preparation of old painted steel surfaces and painting by applying one coat of synthetic enamel paint of approved tint with spray machine and re-fixing of serviceable seat/back/handle/shoes & replacing the unserviceable seat/back/handle/shoes with & including new steel nut and bolts, welding of frame where required etc complete all as specified, shown on drawings and as directed. Notes : (i) The seat, back, handle & shoes to be replaced shall be paid separately under respective serial item No. 9.01 to 9.04 here-in-after as supply only. (ii) Old steel nut & bolts shall not be used. The cost of new steel nut and bolts shall be deemed to be included in the quoted rates of this item. Drg No. TP

Supply only seat of size 575 x 510 mm made of 18mm thick prelaminated particle board (Exterior grade) with & including beading with 4mm thick half round teak wood alround for replacement to chair under serial item No. 9 here-in-before complete all as specified and as directed & conforming to sample kept in GE’s office. Drg No. TP

Supply only back of size 480 x 300 mm made of 18mm thick prelaminated particle board (Exterior grade) with & including beading with 4mm thick half round teak wood alround for replacement to chair under serial item No. 9 here-in-before complete all as specified and as directed & conforming to sample kept in GE’s office. Drg No. TP

Supply only handle of chair easy of size 610 x 60 mm made of 18mm thick plywood with decorative laminated sheet 1.2 mm thick fixed with 4mm dia bolt & nuts with smooth finished edging for replacement to chair under serial item No. 9 here-in-before complete all as specified and as directed & conforming to sample kept in GE’s office. Drg No. TP

Supply only PVC shoe of best quality as shown on drawing for repair to chair under serial item No. 9 here-in-before complete all as specified and as directed & conforming to sample kept in GE’s office. Drg No. TP

M&L for removal of unserviceable wooden plank from Bench Steel and supply & fixing new wooden plank of size 1800 x 380 x 20 mm made of first class hard wood (shisham) fixed to frame (alround) with nut, bolts and washer of size 4mm dia & 50mm long (Eight Nos nut, bolts and washer for each plank) with & including French Polish of gloss finish to all exposed surfaces of wood work complete all as shown on drawing, as specified and as directed. Drg No. TP

S&F in replacement PVC shoe of best quality for Bench Steel complete all as specified and as directed & conforming to sample kept in GE’s office. Drg No. TP

M&L for painting to all steel surfaces of the Bench Steel with one coat of synthetic enamel paint of approved tint with spray machine after preparation of old painted surfaces complete all as specified and as directed. Drg No. TP

S&F shelf of Rack Steel 3 Tier / 6 Tier made of mild steel sheet 1.25 mm thick duly painted with two coats of synthetic enamel paint of olive green shade over a coat of red oxide zinc chromate primer with & including nuts, bolts of suitable size including taking out old unserviceable shelf complete all as shown on drawings, as specified and as directed. Drg No. TP

M&L for painting to all steel surfaces of the Rack Steel 3 Tier with one coat of synthetic enamel paint of approved tint with spray machine after preparation of old painted surfaces complete all as shown on drawings, as specified and as directed. Drg No. TP

M&L for painting to all steel surfaces of the Rack Steel 6 Tier with one coat of synthetic enamel paint of approved tint with spray machine after preparation of old painted surfaces complete all as shown on drawings, as specified and as directed. Drg No. TP

Material & Labour for removing carefully existing broken / unserviceable components/members of Locker Steel and supply & fixing following new components/members duly finished complete all as shown on drawing, as specified and as directed :- Drg No. FD-1029

Hasp & staple 100 mm long mild steel chromium plated (heavy duty) with & including steel screws complete. Drg No. FD-1029

Leg made out of 1mm thick PBI sheet of size & shape as per drawing. Drg No. FD-1029

Aluminium ‘D’ type handle 100 mm long chromium plated heavy duty handle fixed with suitable size new steel screws. Drg No. FD-1029

Painting to all internal and external steel surfaces of the Locker Steel with one coat of synthetic enamel paint of approved tint with spray machine after preparation of old painted surfaces. Drg No. FD-1029

M&L for removing of existing old unserviceable plastic cane from various type of chairs etc and recanning with new cane of white colour of size 2mm wide & 0.40 mm thick half round and 4mm wide & 0.60 mm thick flat for border portion of seat and back as per Godrej Pattern complete all as shown on drawing, as specified and as directed. Drg No. FD-229, FD-279, FD-280 & FD-282

Material & Labour for removing of unserviceable plywood from Charpoy with Hard Top, tightening of all loose components of complete charpoy such as long rails, short rails, legs, etc and supply and fixing 12mm thick Plywood, 7 Ply, commercial type, BWR, exterior grade (water proof), ISI marked, of size 1980 mm x 900 mm in single piece fixed on top of Charpoy with Hard Top, plywood top fixed with and including mild steel galvanized iron nuts & bolts of size 70mm long x 6mm dia (Nos of bolts to be provided - 12 Nos) with GI washers of suitable size (Heavy weight) in sufficient numbers on top of bolts to maintain the plywood top in true leveled position and one GI washer on underside of each bolt for proper tightening of bolt, embossing word "MES” with height of letters 10cm on four corners of the plywood top with thick black synthetic enamel paint, complete all as specified, shown on drawings and as directed. Notes :- (i) The above mentioned size of plywood is firm and no tolerance in size, thickness etc shall be accepted. (ii) Plywood shall be provided in single piece in each Charpoy. (iii) Purchase voucher of plywood shall be obtained by the contractor from authorised dealer/manufacturer and shall be submitted to Engineer-in-Charge. (iv) The cost of welding of frame where required shall be deemed to be included in the quoted rates of this item. Drg No. FD/MAP-II/01

Material & Labour for removing of unserviceable plywood from Charpoy GI pipe, tightening of all loose components of complete charpoy such as check nuts, elbows, long rails, short rails, legs, etc and supply and fixing 12mm thick Plywood, 7 Ply, commercial type, BWR, exterior grade (water proof), ISI marked, of size 1980 mm x 900 mm in single piece fixed on top of Charpoy GI pipe with & including supplying and fixing three Nos stiffeners made out of mild steel flat iron 35mmx5mm, 880mm long between long rails parallel to short rails with equal spacing and power welding duly painted with two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer, plywood top fixed with and including mild steel galvanized iron nuts & bolts of size 70mm long x 6mm dia (Nos of bolts to be provided - 12 Nos) with GI washers of suitable size (Heavy weight) in sufficient numbers on top of bolts to maintain the plywood top in true leveled position and one GI washer on underside of each bolt for proper tightening of bolt, embossing word "MES” with height of letters 10cm on four corners of the plywood top with thick black synthetic enamel paint, complete all as specified, shown on drawings and as directed. Notes :- (i) The above mentioned size of plywood is firm and no tolerance in size, thickness etc shall be accepted. (ii) Plywood shall be provided in single piece in each Charpoy. (iii) Electric arc welding shall be used to fix stiffeners. (iv) Welding rod shall be ISI marked. (v) Purchase voucher of plywood shall be obtained by the contractor from authorised dealer/manufacturer and shall be submitted to Engineer-in-Charge. FD-220

Supply & fixing in position GI 3 way elbow 32mm bore, medium grade (‘B’ Class), ISI marked in Charpoy GI pipe including dismantling & taking out carefully old unserviceable GI 3 way elbow 32mm bore complete all as specified, shown on drawings and as directed. Drg No. FD-220

Material & labour for electric welding of long rails, short rails, legs of 32mm bore GI tubing by continuous welding around the broken joint duly painted with aluminium paint on welded portion complete all as specified & as directed. Notes :- (i) Unit for measurement of this item is ‘Each’ which shall comprise of welding of each broken joint all as specified above. (ii) Welding rods shall be ISI marked. Drg No. FD-220

Material & Labour for removing carefully following existing unserviceable components/members of Bed Plywood Top and supply & fixing new components/members complete all as shown on drawing, as specified and as directed :- Drg No. FD-246 & FD-247

Top of bed of 12mm thick Plywood, 7 Ply, commercial type, BWR, exterior grade (water proof), ISI marked of size 1950mm x 900mm in single piece fixed with screws. Notes :- (i) The above mentioned size of plywood is firm and no tolerance in size, thickness etc shall be accepted. (ii) Plywood shall be provided in single piece in each Bed. (iii) Purchase voucher of plywood shall be obtained by the contractor from authorised dealer/manufacturer and shall be submitted to Engineer-in-Charge. Drg No. FD-246 & FD-247

Long rail of size 100x50x1980mm made out of 1st class hardwood (Shisham). Drg No. FD-246 & FD-247

Short rail made out of long rail retrieved from serial item No. 22.02 here-in-before. Note : Short rail shall be prepared from old long rail and fixed in position. Drg No. FD-246 & FD-247

Ply wood 3mm thick Teak faced to the direct vision of head rest and plywood 3mm thick commercial face to the other side of head rest with & including 4mm thick 1st class hardwood (Shisham) edging alround. Drg No. FD-246 & FD-247

Ply wood 3mm thick Teak faced to the direct vision of foot rest and plywood 3mm thick commercial face to the other side of foot rest with & including 4mm thick shisham wood edging alround. Drg No. FD-246 & FD-247

Leg to Head Rest made out of 1st class hardwood (Shisham) to the required shape & size. Drg No. FD-246 & FD-247

Leg to Foot Rest made out of 1st class hardwood (Shisham) to the required shape & size. Drg No. FD-246 & FD-247

French polish two coats to achieve high gloss finish to Bed Plywood Top including preparation of surfaces by removing old polish by scraping & rubbing with suitable sand paper, filling putty wherever required and making the surfaces smooth complete all as specified, shown on drawings and as directed. Drg No. FD-246 & FD-247

Material & Labour for removing carefully following existing unserviceable components/members of Bed Hard Steel with Ply Top and supply & fixing new components/members complete all as shown on drawing, as specified and as directed :- Drg No. FD/E6/MAP/08(R)

Removing of unserviceable plywood from Bed Hard, tightening of all loose components of complete Bed Hard including electric welding where required such as broken/loose mild steel long rails, short rails, legs, stiffeners, head rest, foot rest, cleats, etc by continuous welding around the broken joints and supply and fixing 12mm thick Plywood, 7 Ply, commercial type, BWR, exterior grade (water proof), ISI marked, of size 1980 mm x 900 mm in single piece fixed on top of Bed Hard, plywood top fixed with and including mild steel galvanized iron nuts & bolts of size 70mm long x 6mm dia (Nos of bolts to be provided - 12 Nos) with GI washers of suitable size (Heavy weight) in sufficient numbers on top of bolts to maintain the plywood top in true leveled position and one GI washer on underside of each bolt for proper tightening of bolt, embossing word "MES” with height of letters 10cm on four corners of the plywood top with thick black synthetic enamel paint, including painting to complete Bed Hard with one coat of synthetic enamel paint (Black) by spray machine after preparation of steel surfaces and providing new hard rubber shoes at the bottom of all legs after removing of old shoes, complete all as specified, shown on drawings and as directed. Notes :- (i) The above mentioned size of plywood is firm and no tolerance in size, thickness etc shall be accepted. (ii) Plywood shall be provided in single piece in each Bed Hard. (iii) Purchase voucher of plywood shall be obtained by the contractor from authorised dealer/manufacturer and shall be submitted to Engineer-in-Charge. (iv) The cost of welding & minor repairs of frame where required shall be deemed to be included in the quoted rates of this item. Drg No. FD/E6/MAP/08(R)

Head rest made of 18mm thick prelaminated particle board both side teak face of exterior grade with 4mm thick teak wood beading alround fixed with screws and necessary welding of cleats. Drg No. FD/E6/MAP/08(R)

Foot rest made of 18mm thick prelaminated particle board both side teak face of exterior grade with 4mm thick teak wood beading alround fixed with screws and necessary welding of cleats. Drg No. FD/E6/MAP/08(R)

Material & Labour for removing carefully existing broken / unserviceable components/members of Almirah Small Steel and supply & fixing following new components/members duly finished complete all as shown on drawing, as specified and as directed :- Drg No. FD-67 & FD-1032

Three way locking device complete made of standard manufactures like Godrej or its equivalent with & including replacement of steel screws. Drg No. FD-67 & FD-1032

Lock of 3 levers (ISI marked) with double keys with & including replacement of steel screws. Drg No. FD-67 & FD-1032

Leg made out of 1mm thick PBI sheet of size & shape as per drawing. Drg No. FD-67 & FD-1032

MS cleat to support shelf duly painted with two coats of synthetic enamel paint of olive green shade with nuts, bolts of suitable size including welding of broken shutter of almirah. Drg No. FD-67 & FD-1032

Chromium plated MS handle of appropriate size & shape as per existing Godrej pattern heavy duty fixed with suitable size new steel screws. Drg No. FD-67 & FD-1032

Shelf made of mild steel sheet 1mm thick duly painted with two coats of synthetic enamel paint of olive green shade with nuts, bolts of suitable size complete. Drg No. FD-67 & FD-1032

Preparation of steel & iron surfaces of Almirah Small Steel and applying one spray coat of synthetic enamel paint (OG colour) on all steel & iron surfaces (inside & outside including shelves etc.) complete all as specified & as directed. Drg No. FD-67 & FD-1032

Material & Labour for removing carefully existing broken / unserviceable components/members of Almirah Large Steel and supply & fixing following new components/members duly finished complete all as shown on drawing, as specified and as directed :- Drg No. FD-67 & FD-1031

Three way locking device complete made of standard manufactures like Godrej or its equivalent with & including replacement of steel screws. Drg No. FD-67 & FD-1031

Lock of 3 levers (ISI marked) with double keys with & including replacement of steel screws. Drg No. FD-67 & FD-1031

Leg made out of 1mm thick PBI sheet of size & shape as per drawing. Drg No. FD-67 & FD-1031

MS cleat to support shelf duly painted with two coats of synthetic enamel paint of olive green shade with nuts, bolts of suitable size including welding of broken shutter of almirah. Drg No. FD-67 & FD-1031

Chromium plated MS handle of appropriate size & shape as per existing Godrej pattern heavy duty fixed with suitable size new steel screws. Drg No. FD-67 & FD-1031

Shelf made of mild steel sheet 1mm thick duly painted with two coats of synthetic enamel paint of olive green shade with nuts, bolts of suitable size complete. Drg No. FD-67 & FD-1031

Preparation of steel & iron surfaces of Almirah Large Steel and applying one spray coat of synthetic enamel paint (OG colour) on all steel & iron surfaces (inside & outside including shelves etc.) complete all as specified & as directed. Drg No. FD-67 & FD-1031

Material & Labour for removing carefully existing broken / unserviceable components/members of Table Bed Side and supply & fixing following new components/members duly finished complete all as shown on drawing, as specified and as directed :- Drg No. FD-276

18mm thick prelaminated particle board side runner including legs of table with 4mm thick teak wood beading all around. Drg No. FD-276

18mm thick prelaminated particle board top side of the table made out of teak faced with 4mm thick teak wood beading all around. Drg No. FD-276

18mm thick prelaminated particle board top / shelf & bottom shelf of the table made out of teak faced. Drg No. FD-276

Plywood 4mm thick commercial on back side of the table bed side. Drg No. FD-276

Material & Labour for removing carefully existing broken / unserviceable components/members of Table Centre (900 x 450 x 400) and supply & fixing following new components/members duly finished complete all as shown on drawing, as specified and as directed :- Drg No. FD-274

Table top made of 18mm thick prelaminated particle board (Exterior grade) one side decorative of approved shade of size 900 x 450 mm fixed with screws with & including 4mm thick half round teak wood edging fixed alround to top. Notes : (i) Table top shall be provided in single piece. (ii) French polish with high gloss finish shall be provided to exposed wooden surfaces of teak wood edging. Drg No. FD-274

Front and back rail made of 1st Class hardwood (Teak wood). Drg No. FD-274

Short rail made of 1st Class hardwood (Teak wood). Drg No. FD-274

Legs square & round type made of 1st Class hardwood (Teak wood). Drg No. FD-274

Short/long stiffeners made of 1st Class hardwood (Teak wood). Drg No. FD-274

Corner / bracket (L shape) of size 50 x 50 x 20 mm thick made of 1st Class hardwood (Teak wood) and fitted with screws between long rail to legs and short rail to legs. Drg No. FD-274

French polish two coats to achieve high gloss finish to Table Centre (900 x 450 x 400) including preparation of surfaces by removing old polish by scraping & rubbing with suitable sand paper, filling putty wherever required and making the surfaces smooth complete all as specified, shown on drawings and as directed. Drg No. FD-274

Material & Labour for removing carefully existing broken / unserviceable components/members of Chair Writing and supply & fixing following new components/members duly finished complete all as shown on drawing, as specified and as directed :- Drg No. FD/E6/MAP/12

Tapestry/Fabric cloth over & including synthetic foam 25mm thick (as approved), 32 density for seat, 12mm hot pressed plywood of Chair Writing. Note : Tapestry cloth shall be good quality (indigenous make) and costing not less than Rs. 300.00 per metre (width not less than 1.25 metre) as approved by GE. The rate mentioned above shall be considered as rate ex-shop. The shade/ texture shall be approved by the GE. Drg No. FD/E6/MAP/12

Tapestry/Fabric cloth over & including synthetic foam 25mm thick (as approved), 32 density for back, 12mm hot pressed plywood of Chair Writing. Note : Tapestry cloth shall be good quality (indigenous make) and costing not less than Rs. 300.00 per metre (width not less than 1.25 metre) as approved by GE. The rate mentioned above shall be considered as rate ex-shop. The shade/ texture shall be approved by the GE. Drg No. FD/E6/MAP/12

Handle of chair writing including welding of broken joints and painting of steel frame surface of the chair with one coat of synthetic enamel paint of black shade. Notes :- (i) Cost of minor repair and welding to frame where required is deemed to be included in the quoted rate. (ii) Cost of all nut, bolts and screws and painting of the chair deemed to be included in the quoted rate. Drg No. FD/E6/MAP/12

Material & Labour for removing carefully existing broken / unserviceable components/members of Table Office Clerk (Steel) and supply & fixing following new components/members duly finished complete all as shown on drawing, as specified and as directed :- Drg No. FD-1004

Table top made of 18mm thick prelaminated particle board (Exterior grade) one side decorative of approved shade fixed with screws with & including 4mm thick half round teak wood edging fixed alround to top. Note : Table top shall be provided in single piece. Drg No. FD-1004

Taking out old unserviceable drawer from the table and refixing the same after repair by proper welding & denting and making the same fully functional. Drg No. FD-1004

Lock 40 mm size of brass, 4 lever (ISI marked) with 02 keys. Drg No. FD-1004

PVC shoe of best quality conforming to sample kept in GE’s office. Drg No. FD-1004

Replacing damaged portion of leg with new 25mm square mild steel tube of 1.6mm wall thickness, 10cm in length by cutting the damaged portion with hacksaw & fixing of new tube to leg by gas welding including applying one coat of synthetic enamel paint of approved tint over a coat of red oxide zinc chromate primer on new pipe and one coat of paint on portion disturbed during welding complete all as shown on drawing, specified and directed. Drg No. FD-1004

Preparation of steel & iron surfaces of Table Office Clerk (Steel) and applying one spray coat of synthetic enamel paint (OG colour) on all steel & iron surfaces including drawers (inside & outside) etc complete all as specified & as directed. Drg No. FD-1004

Material & Labour for removing carefully existing broken / unserviceable components/members of Table Officers (Steel) and supply & fixing following new components/members duly finished complete all as shown on drawing, as specified and as directed :- Drg No. FD-1003

Table top made of 18mm thick prelaminated particle board (Exterior grade) one side decorative of approved shade fixed with screws with & including 4mm thick half round teak wood edging fixed alround to top. Note : Table top shall be provided in single piece. Drg No. FD-1003

Taking out old unserviceable drawer/shutter from the table and refixing the same after repair by proper welding & denting and making the same fully functional. Drg No. FD-1003

Lock 40 mm size of brass, 4 lever (ISI marked) with 02 keys. Drg No. FD-1003

PVC shoe of best quality conforming to sample kept in GE’s office. Drg No. FD-1003

Replacing damaged portion of leg with new 25mm square mild steel tube of 1.6mm wall thickness, 10cm in length by cutting the damaged portion with hacksaw & fixing of new tube to leg by gas welding including applying one coat of synthetic enamel paint of approved tint over a coat of red oxide zinc chromate primer on new pipe and one coat of paint on portion disturbed during welding complete all as shown on drawing, specified and directed. Drg No. FD-1003

Preparation of steel & iron surfaces of Table Officers (Steel) and applying one spray coat of synthetic enamel paint (OG colour) on all steel & iron surfaces including drawers (inside & outside), shutter etc complete all as specified & as directed. Drg No. FD-1003

Material & Labour for removing carefully existing broken / unserviceable components/members of Table Dining (For 6 Persons) (1500 x 900 x 760) and supply & fixing following new components/ members duly finished complete all as shown on drawing, as specified and as directed :- Drg No. FD-273

Table top made of 18mm thick prelaminated particle board (Exterior grade) one side decorative of approved shade of size 1500 x 900 mm fixed with screws with & including 4mm thick half round teak wood edging fixed alround to top. Notes : (i) Table top shall be provided in single piece. (ii) French polish with high gloss finish shall be provided to exposed wooden surfaces of teak wood edging. Drg No. FD-273

Front and back rail made of 1st Class hardwood (Teak wood). Drg No. FD-273

Short rail made of 1st Class hardwood (Teak wood). Drg No. FD-273

Legs square & round type made of 1st Class hardwood (Teak wood). Drg No. FD-273

Top centre stiffeners of size 100x25mm made of 1st Class hardwood (Teak wood). Drg No. FD-273

Corner / bracket (L shape) of size 100 x 100 x 25 mm thick made of 1st Class hardwood (Teak wood) and fitted with screws between long rail to legs and short rail to legs. Drg No. FD-273

French polish two coats to achieve high gloss finish to Table Dining (For 6 Persons) (1500 x 900 x 760) including preparation of surfaces by removing old polish by scraping & rubbing with suitable sand paper, filling putty wherever required and making the surfaces smooth complete all as specified, shown on drawings and as directed. Drg No. FD-273

Material & Labour for removing carefully existing broken / unserviceable components/members of Table with Drawer (900 x 600 x 760) and supply & fixing following new components/members duly finished complete all as shown on drawing, as specified and as directed :- Drg No FD-283

Table top made of 18mm thick prelaminated particle board (Exterior grade) one side decorative of approved shade of size 900 x 600 mm fixed with screws with & including 4mm thick half round teak wood edging fixed alround to top. Notes : (i) Table top shall be provided in single piece. (ii) French polish with high gloss finish shall be provided to exposed wooden surfaces of teak wood edging. Drg No FD-283

Long rail made of 1st Class hardwood (Teak wood). Drg No FD-283

Short rail made of 1st Class hardwood (Teak wood). Drg No FD-283

Legs made of 1st Class hardwood (Teak wood). Drg No FD-283

Stiffeners made of 1st Class hardwood (Teak wood). Drg No FD-283

Corner / bracket (L shape) of size 100 x 100 x 25 mm thick made of 1st Class hardwood (Teak wood) and fitted with screws between long rail to legs and short rail to legs. Drg No FD-283

Drawer complete as per drg. Drg No FD-283

French polish two coats to achieve high gloss finish to Table with Drawer (900 x 600 x 760) including preparation of surfaces by removing old polish by scraping & rubbing with suitable sand paper, filling putty wherever required and making the surfaces smooth complete all as specified, shown on drawings and as directed. Drg No FD-283

M&L for repair to Double Bed Bunk of size 1980 x 900 x 1750 mm by removing of unserviceable plywood from double bed bunk on both upper and lower top, supply and fixing the 12mm thick Plywood, 7 Ply, commercial type, BWR, exterior grade (water proof), ISI marked, of size 1980 mm x 900 mm in single piece with mild steel galvanized iron nuts & bolts of size 70mm long & 6mm dia with GI washers (heavy weight) and including electric welding of loose upper and lower frame, centre stiffener and cleat tube size of 50mm x 100mm x 6mm of MS pipe by continuous welding around the broken joints and also replacement of old unserviceable above parts with new parts where required and also including painting with one coat of synthetic enamel paint (Black) by spray machine after preparation of old painted steel surfaces complete all as specified and directed. Notes :- (i) Cost of minor repair and welding to frame where required shall deemed to be included in the quoted rate. (ii) Cost of all type of nuts, bolts and washers and painting of the double bed bunk shall deemed to be included in the quoted rate. (iii) The above mentioned size of plywood is firm and no tolerance in size, thickness etc shall be accepted. (iv) Plywood shall be provided in single piece. (v) Purchase voucher of plywood shall be obtained by the contractor from authorised dealer/manufacturer and shall be submitted to Engineer-in-Charge. Drg No TP

Supply and fixing in replacement legs of multi seater chair easy steel including electric welding of loose seat frame, MS pipe by continuous welding around the broken joints and also replacement of old unserviceable parts with new parts where required and painting with one coat of synthetic enamel paint black / silver by spray machine after preparation of old painted steel surfaces complete all as specified and directed. Notes :- (i) Cost of minor repair and welding to frame where required shall deemed to be included in the quoted rate. (ii) Cost of all type of nuts, bolts and washers and painting of the multi seater chair shall deemed to be included in the quoted rate. Drg No TP

B K CONTRACTORS

M/s Rohit Construction Co.