PROVN OF UNISEX TOILET UNDER GE (CME) KHADKI

Amount

Excavating in trenches, n.exc 1.5 m wide and n exc 1.5m in depth; for foundation, or for shafts, wells, cesspits, manholes, pier holes,or for laying cable , pipe etc and getting out in hard / dense soil complete all as specified and as directed by Engineer-in -Charge.

Excavating over areas n. exc 1.5m deep and getting out in hard / dense soil complete complete all as specified and as directed by Engineer-in -Charge.

M & L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed by Engineer-in -Charge.

M & L Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed by Engineer-in -Charge

M & L Cement concrete M-7.5 grade (Nominal Mix) using 40mm graded stone aggregate in foundations, filling and mass concrete,complete all as specified and as directed by Engineer-in -Charge.

M&L for Brickwork with fly ash bricks old size, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and as directed by Engineer-in -Charge

M&L for use and waste of steel formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides of soffits (if any) of foundation and plinth beams, and similar work, vertical or to batter to rough finished surfaces of concrete flat complete all as specified and as directed by Engineer-in -Charge.

M&L for use and waste of steel formwork to sides of pillars, posts, struts, piers, columns and stanchions square, rectangular or polygonal to rough finished surfaces of concrete flat complete all as specified and as directed by Engineer-in -Charge.

M&L for use and waste of steel formwork to sides and soffits of beams, linels, cantilevers, shelves incl supports, overhangs, etc also splays between floors and beams, etc and similar work,to rough finished surfaces of concrete flat complete all as specified and as directed by Engineer-in -Charge.

M&L for Reinforced cement concrete M-25 (Design mix) using 20mm graded stone aggregate in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed by Engineer-in -Charge.

M&L for Reinforced cement concrete M-25 (Design mix) using 20mm graded stone aggregate as in columns, pillars, piers postsand structs complete all as specified and as directed by Engineer-in -Charge.

M&L for Reinforced cement concrete M-25 (Design mix) using 20mm graded stone aggregate as in Beams, cantilevers, bressumers, lintels over 1.50 span complete all as specified and as directed by Engineer-in -Charge.

M & L for rolled mild steel work in Joist, channel, angle or tee sections, fixed independently without copnnecting plates etc (cut to ordinary lengths confirming to Feb 410W Gde-E-250 quality-A) complete all as specified and as directed by Engineer-in -Charge.

M & L for rolled mild steel work in plates (plain or chequered) channels, square cut or notched (ordinary and counter suck) confirming to Fe 410-W (Gde E-250, Quality-A forming holes without any attached complete all as specified and as directed by Engineer-in -Charge.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in roof covering fixed with self tapping screws complete all as specified & as directed by Engineer-in-Charge.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 as in cladding to wall , ridge, eaves gutters with end stops,drop ends or nozzles etc, fixed with self tapping screws complete all as specified & as directed by Engineer-in-Charge.

M & L TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & as directed by Engineer-in-Charge.

M & L TMT steel bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binder , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & as directed by Engineer-in-Charge.

S & F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed by Engineer-in -Charge.

S & F Steel ventilators with centre hung shutter including two pairs of brass cup pivots, catch spring and pulley wheel, complete all as specified and as directed by Engineer-in -Charge.

S & F 5mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and as directed by Engineer-in -Charge.

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening complete all as specified & as directed by Engineer-in-Charge.

S & F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing and Plain colour PVC sheet fixed or laid on to flush doors by using rubber based adhesive, supplying & fixing at site complete all as specified & as directed by Engineer-in-Charge.

Supply and fix 100mm butt hinges extruded aluminum alloy with mild steel hing pin anodized and fixed type B-22 complete all as specified & as directed by Engineer-in-Charge.

Supply and fix Aluminium anodized barrel tower bolts of extruded section, 125 mm long complete all as specified & as directed by Engineer-in-Charge.

Supply and fix Aluminium handles, cast type, anodized, 150mm size complete all as specified & as directed by Engineer-in-Charge.

S&F MS flat iron as in hold fast complete all as specified & as directed by Engineer-in-Charge.

M & L for 100 mm thick Cement concrete M-15 (Nominal Mix) using 40mm gradedstone aggregate as in floor complete all as specified and as directed by Engineer-in -Charge.

M&L colourd Non Skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or colourd cement to match the shade of the tiles and laid over & including 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engr-in-Charge.

M & L for Glazed ceramic tiles in vertical surface 300X200X7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tile laid over and including cement plaster 10mm thick as in backing coat in CM 1:4 complete all as specified and as directed by Engr-in-Charge.

M & L Granite work 18 to 20 mm thick telephonic black shade table rubbed, polished and edges molded as required at site in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed by Engr-in-Charge.

M & L for Machine cut cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed by Engineer-in -Charge

Supplying & fixing to walls and ceiling 15 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed by Engineer-in -Charge

Supplying & fixing to walls and ceiling 20 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed by Engineer-in -Charge

Supply and fix for 110mm dia PVC (SWR) pipesType B single socketed in any length with rubbing ring joints fixed to walls complete all as specified and as directed by Engineer-in -Charge

Supply and fixing of 110mm dia PVC (SWR) bends for any radius complete all as specified and as directed by Engineer-in -Charge

Supply and fixing of 110 mm dia PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and as directed by Engineer-in -Charge

Supply and fix for 75 mm dia PVC (SWR) pipesType B single socketed in any length with rubbing ring joints fixed to walls complete all as specified and as directed by Engineer-in -Charge

Supply and fixing 75 mm PVC (SWR) vent cowl complete all as specified and as directed by Engineer-in -Charge

Supply and fixing of 75mm dia PVC (SWR) floor trap, plain incl jointing with solvent cement complete all as specified and as directed by Engineer-in -Charge

Supply and fixing of Grating doom 125mm dia with waste hole of PTMT (minimum weight 40 grms) complete all as specified and as directed by Engineer-in -Charge

S&F PVC gully trap square or round mouthed type (P) , size of trap 125x 110mm and jointing to drains with solvent cement in repairs complete all as specified and as directed by Engineer-in -Charge

M&L for PVC (SWR) Reducer 110/75mm diacomplete all as specified and as directed by Engineer-in -Charge

S & F Stop valve 15mm bore, cast copper alloy screwed down, high pressure, with crutch jor butter fly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed by Engineer-in -Charge.

Supply and fix bib tap, chromium plated, cast copper alloy, crutch or butterfly handle, screwed down, screwed for iron pipes or brass ferrule, 15mm bore,complete all as specified and as directed by Engineer-in -Charge.

M & L for CP Pillar taps, with capstan head chromium plated 15 mm bore fancy type complete all as specified and as directed by Engineer-in -Charge

S & F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed by Engineer-in -Charge

M & L for 600mm long Towel Rail of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed by Engineer-in -Charge.

M & L for Ball brass valves for 20mm pipe, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed

Supply and fixing of stainless steel soap dish any type, fixed to with walls and plugs with chromium plated brass screws complete all as specified and as directed by Engineer-in -Charge.

S&F PVC connection 15mm size with PTMT nuts of length 450 mm long complete all as specified.

S&F wash hand basin vitreous china white flat back size 550X400mm including CI bracket, 15mm dia polythene connection, 32mm dia chromium plated (CP) waste coupling chain and plug waste filling union and 32mm dia PVC waste pipe 90cm long, all necessary inlet outlet connections complete all as specified and as directed by Engineer-in -Charge.

S&F 10 ltr capacity PVC valveless, syphonic action type flushing cistern, low level, white, with inlet ball valve, float and handle including brackeet and 32mm dia flush pipe of polyethylene of low or high density for low level cistern complete all as specified and as directed by Engineer-in -Charge.

S&F Vitreous China Urinal, full stall type, white with flush pipe complete all as specified and as directed by Engineer-in -Charge.

S & F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete in all respectcomplete all as specified and as directed by Engineer-in -Charge.

S & F Vitreous china urinal partition white of size 310x700 mm. complete all as specified and as directed by Engineer-in -Charge.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) but including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonage pipe, seat cover complete, all as specified and directed.

M&L for Vitreous china squatting Pan "Orrisa Pattern" size 580 x 440mm white with integral foot rests incl flush pipe of PVC 32mm dia for low level cistern fixed in repair complete all as specified and as directed by Engineer-in -Charge.

Material and labour for providing precast RCC cover slab M-15 grade (Nominal Mix) (for man holes, drain cover etc) using 20mm graded stone aggregates including necessary use and waste of formwork and set in CM (1:6) complte with joints to match complete all as specified and as directed by Engineer-in -Charge.

Supply and fix 500 liters capacity triple layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc complete all as specified and as directed by Engineer-in -Charge.

S&F 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed by Engineer-in -Charge.

M&L rendering 15 mm thick (10mm + 5mm) plaster on fair face of brick work , concrete or PCC block masonry in CM 1:4 and surface finished even and fair by mixing liquid water proofing compound as per manufacturers instructions complete. Note :- Liquid WPC shall be measured & paid seprately under relevant item of this BOQ.

Supply only liquid water proofing compound hydroseal-W+ or eqivalent (for plaster hardening, to control efflorescence & fungal growth) as approved by GE.

M&L Rendering 10 mm thick on fair faces of brick work or concrete surface, in cement mortar 1:4 finished the surface even and smooth without using extra cement ,complete all as specified and as directed by Engineer-in -Charge.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint over one coat of chalk whiting primer on wall including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed by Engineer-in -Charge.

M & L for prepartion of newly plastered surfaces and applying two coat of oil emulsion distemper over a coat of alkali resistant cement primer over wall care putty not less than 1mm thick complete all as specified and as directed by Engineer-in -Charge.

M&L for prepration of new steel surfaces of any description not otherwise described over 10cm width or girth applying two coats of synthetic enamel paint over a coat of red oxide primer all as directed by Engr-in-charge.

M & L for 75mm thick plain cement concrete M-10 grade (Nominal Mix) using 20mm graded crushed stone aggregate laid in alternate bays (not exc 2 sqm each) as in plinth protection, finished the surfaces even and fair, incl making joints 10mm wide and 30mm deep at spacing not more than 2.50 mtr and at corners and as mandatory and filled with 1 part of bitumen mixed with 3 parts of sand along with wall and in between bays complete all as specified and as directed by Engineer-in -Charge

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete.

Removing excavated material exc. 250 m but n exc. 500 m and depositing where directed

M&L for Brickwork with fly ash bricks old size, straight or curved on plan any radius in half brick thick built in CM 1:4 complete all as specified and as directed by Engineer-in -Charge

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc, and cutting chases for concelaed water tubing or concealed conduit wiring etc. and making good, cutting not exc 10 cm girth complete all as specified and directed.

M&L for 75 mm thick PCC M-7.5 grade (Nominal Mix) using 40mm graded stone aggregate) as in sub base complete all as specified and as directed by Engineer-in -Charge.

M&L for Sand filling under floors or in foundation including consolidation. The thickness of sand cushion should not be less than 25mm for laying paver blocks.

M&L Machine pressed precast concrete interlocking pavour block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 grade with glossy finish colour shade as decided by Engr-in-Charge.

M&L Hardcore of gauge exc 63 mm but n exc 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface complete all as specified and as directed by Engineer-in -Charge.

M & L PCC M-15 grade (nominal mix) using 20mm graded stone aggregate as in roof kerbs of mud stops, rounded or chamfered on edges or as in sunken floor complete all as specified & directed

Removing excavated material (soil) not.exceeding 50m and deposited where directed at a level not.exceeding 1.5 m above the starting point complete as specified and directed by Engr-in-Charge.

Excavation in trenches n.exc 1.50m wide and 1.50m depth for foundation, man hole etc and getting out in soft/loose soil

M&L cement concrete M-15 grade (nominal mix) using 40mm graded aggregate as in surface channels and drain complete all as specified and as directed by Engineer-in -Charge.

M & L for Pre-cast cement concrete (design Mix) C-5 block masonry , exc. 10 cm in width buit in CM 1:6 , complete all as specifed and as directed

M & L for rendering 15 mm thick in CM 1:4 on other than fair faces of brick work or concrete surfaces finished even and smooth without using any extra cement complete all as specified & directed.

M&L for RCC drain pipes 150mm , class NP-3 laid in trenches and jointed complete with collar all as specified complete as specified and directed by Engr-in-Charge.

M&L for PCC M-7.5 grade (Nominal mix) 40mm graded stone aggregate as in concrete bed to RCC drain pipes including packing under and hunching against side of pipes with concrete after they are laid and join ted, dia of pipe 150mm complete as specified and directed by Engr-in-Charge.

M&L plain cement concrete M-15 grade (Nominal mix) , using 20mm graded stone aggregates, as in copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, including provn of form work if required as directed.

M&L for Reinforcement Cement concrete M-15 grade (Nominal Mix) using 20mm grades stone aggregate as in cover slab for drain & manholes etc. as directed incl use and waste of necessary form work complete all as spd.

M&L TMT bars 6mm to 8mm dia and over cut to length, bent to shape required including cranking, bending hooking ends, and binding with mild steel wire not less than 0.9 mm dia complete all as specified and as directed.

M & L for Construction of Soakage wells excavation, in any type of soil, foundation in PCC M-10 grade (Nominal Mix) using 40mm graded stone aggregate, walls of honey combed masonry with top ring of M-25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M-25 SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 1.2m dia X 3m effective depth, complete. As per Drg No. CEPZ/2019/TD/03

M & L for On site LLDPE septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC M-7.5 grade (Nominal Mix) using 40mm graded stone aggregate below foundation, Vent shaft, connection etc., complete for 10 User complete all as specified and directed.

S&F two way bib tap 15mm chromium plated complete all as specified and directed. Make : Cera F1020161-chrome

M&L Point wiring complete using 650/1100 Volts grade single core PVC FRLSH insulated, unsheathed having bright annealed multi-stranded copper conductor cables 1.5 Sqmm (22/0.30 mm) (nominal area) conforming to IS-694:2010, two runs of cables for phase, neutral and one run of cable as earth continuity conductor, colour coded as per IS-11353:1985, drawn through and including PVC concealed conduit of suitable dia with accessories and fittings, including cutting chases, factory made sunken enclosure made out MS sheet not less than 1.2mm thick having zinc coating not less than 120 GSM, confirming to IS-14772:2000, having top, bottom, side and back wall knockouts for casing capping entry from any direction for mounting switches, sockets, fan regulators etc and back wall knockouts for conduit entry from any direction for mounting switches, sockets, fan regulators etc with and including suitable hylum sheet cover plates, complete and earth wire connected to luminaries/fans etc; at one end and to common earth dolly at other end, all as specified and directed for the metallic bodies of luminaries/fans etc; at one end and to common earth dolly at other end, all as specified and directed for the following-

One light point controlled by one number one way switch.

One exhaust fan point controlled by one, one way switch

One 3 pin switch socket outlet 6 Amp on independent board

One 3 pin switch socket outlet 6 Amp on the same board with other switches

Ditto- all as per item No 92 here-in before but using 2.5 Sqmm (36/0.30 mm) cables for one 16 Amp, 6-Pin socket outlet point on independent board

S&F Switch piano flush type 5/6 Amp single pole one way 230 voltscomplete all as specified and directed.

S&F Switch piano flush type 16 Amp single pole one way 230 voltscomplete all as specified and directed.

S&F Socket outlet, flush type, multipurpose 230 volts, suitable for 2 in 1, 3 pin 6 Amp plug, complete all as specified and directed

S&F Socket outlet, 2 in 1, flush type, universal, 230 volts, suitable for 3 pin 6 Amp and 3 pin 16 Amp plug complete all as specified and directed.

S&F ceiling rose, PVC/polycarbonate isolated body, ISI Marked, with 3 terminals complete all as specified and directed.

Supply and fix Exhaust fan 300 mm sweep, steel body ,single phase, AC 230 Volt heavy duty, with blade frame and louvers shutter including three core flexible copper conductor cable of required length of size 23/0.0076 from ceiling rose/ connector to fan terminal, fixing the fan with suitable size of nut, bolt washer, complete all as specified and directed

S&F LED lights fitting 1 x 20 W, 220V, AC decorativebox type with driver, holder including LED tube light including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose. complete all as specified and directed.

S&F LED lights fitting mirror type with high out diffuser 2 feet 10 watt 220 v AC decorative type with driver holder and LED lamp 1 x 10 W, 2 feet long, 220V, AC decorative ultra slim Square profile with extruded polycarbonate type with driver, holder including connecting up flexible copper conductor cable of suitable size from ceiling rose. complete all as specified and directed.

S & F Factory made sheet metal enclosure of MCB DB, SPN 230 Volts, double door front openable, protection class IP-43, 8 way with 100 A rated bus bar and neutral bus terminal for mounting MCBs and for 8 way circuits complete, fixed flush with wall in wall nitch, making incoming and outgoing electric connection with lugs / thimbles etc. complete all as specified and directed.

S&F MCB SPN 32 Amp, current rating 240 Volts, 10 KA, 'B' curve provided in the MCB DB complete with connection, testing and commissioning all as specified and directed.

S&F MCB SP 6 to 32 Amp (as directed), current rating 240 Volts, 10 KA, 'B' curve provided in the MCB DB complete with connection, testing and commissioning all as specified and directed.

S & F t LED light fitting 35 watt , 230 V for building security out door type with high ptressure die cast aluminuim housing and heat resistant complete with driver lamp bracket with impact and corrosion resistant including thermal management in multiple optics with IP65/ 66 Protection with three core flexible 1.5sqmm copper wire from connecto to ceiling roseand fifix on wall with clamp and nut bolt and necessary GI bracket made of 32 mm medium grade GI piupe 1m long with necssary bending compete all as specified and directed

Material and labour for earthing complete with GI earth plate 600mm x 600mm x 6 mm thick electrode buried directly in ground (earth pit not less then 2.25 metres deep below ground level ) with top edge of the plate not less then 1.5 metres below normal ground level connected to GI wire 4 mm as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES schedule Part-I and including 15 mm bore light grade GI protection pipe (upto 7.5 metres beyond outer edge of earth pit) PCC M-10 grade (Nominal Mix) using 40mm graded stone aggregate in pit with 40mm thick RCC cover in reinforced cement concrete M-15 grade (Nominal Mix) using 20mm graded stone aggregate, reinforced with 8mm dia bar both way @ 150mm c/c, watering arrangement with funnel and wire mesh and 20 mm bore light grade GI watering pipe, common salt and chaarcoal filling, necessary excavation and earth work complete.

Supplying & fixing to walls or ceiling 20 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 laid in trench complete all as specified and as directed by Engineer-in-Charge.

Cutting 40/50mm bore existing steel tubing for alteration or additions of new pipe connection of 20 mm bore with necessary Tee, bends etc complete all as specified and directed by Engr in charge.

Supply , laying, connecting and testing cable XLPE insulated screened PVC bedded galvanised steel strip or wire armoured , electric power cables ( heavy duty) with stranded aluminium conductor 1100 volts grade in trenches/ passing through pipe/fixing on walls, floors etc incl using suitable clamp of cross sectional area 2 core 10 Sqmm Sqmm all as specified and directed.

Supply and lay double wall corrugated (DWC) high density polythene pipes having corrugation on the outer wall and plain surface on the inner wall confirming to IS 16205 & IS14930 ( Part I and II) for protection of under ground cable of size 40 mm outer dia with all fittings such as clamps. coupler etc laid in trenches / road / nallah or fixed along wall. poles or laid under floor (including cutting floor/Road and making good to match with existing adjoining surface etc) for cable protection complete all as specified Note :- Excavation and earth work shall be measured and paid separately under revant item of Schedule

Horizon Construction (BID ID -3393487)

vishalconstruction (BID ID -3393327)

MAHESH DADAJI BACHHAV (BID ID -3383935)

Decent Decorators (BID ID -3393163)

BSK Construction (BID ID -3393619)

Bidder Name

BSK Construction

Horizon Construction

vishalconstruction

MAHESH DADAJI BACHHAV

ShreHari Civil Enginneering and Contractors

Decent Decorators