Creation of facility for disabled person wash room at Dr YSP University of Horticulture and Forestry Nauni, Solan SH Civil Work.

Amount

Excavation in foundation trenches etc. in all kinds of soil such as pick work, jumper work including chiseling / wedging etc. with all lifts stacking the excavated soil not more than 3 metres clear from the edge of excavation and then returning the stacked soil in 15 cm layers, when required into plinth sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed with all leads and lifts of material as directed by the Engineer-in-Charge.

Filling in plinth with sand under floors including watering ramming consolidating and dressing complete including all leads and lifts of material as directed by the Engineer-in-Charge.

Form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies height of propping and centring below supporting floor to ceiling not exceeding 4 metres and removal of the same for insitu-reinforced concrete complete and plain concrete work including all leads and lifts of material as directed by the Engineer-in-Charge.

a) Foundation footings, bases of column etc. and mass concrete.

b) Flat surface such as soffits of suspended floors, roofs landing and the like Floor etc. upto 200mm in thickness.

c) Beams, cantilever, girders and lintel : Sides and soffits of beams, beam haunchings, cantilevers, girders bressurmers and lintels not exceeding metre in depth.

Providing and laying cement concrete 1:6:12 (one cement: six sand and twelve graded stone crushed aggregate 40mm (forty milimetre nominal size) curing complete excluding cost of form work in foundation and plinth in all leads and lifts of material as directed by the Engineer-in-Charge.

Providing and laying damp proof course to horizontal / vertical surfaces with cement mortar 1:2 (one cement : two sand) and curing complete in all respect as per satisfaction of Engineer-in-charge. a) 20mm thick

Providing and laying cement concrete work mix 1:2:4 (one cement : two sand: four graded stone crushed aggregate 20mm (twenty millimetre nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in all leads and lifts as directed by the Engineer-in-charge.

a) Foundations, footings bases of column and the like and mass concrete.

b) Suspended floor roofs, landings and shelves and their supports balconies, beams girders, bressurmers and cantilevers upto all floor level.

Providing TMT steel reinforcement for R.C.C. work including bending binding and placing in position complete upto all floor level including all leads and lifts of material as directed by the Engineer-in-Charge.

2nd class brick work using common burnt clay building bricks in foundation and plinth in cement mortar 1:6 (one cement : six sand) including all leads and lifts of material as directed by the Engineer-in-Charge.

2nd class brick work using common burnt clay building bricks in superstructure in cement mortar 1:6 (one cement: six sand) including all leads and lifts of material as directed by the Engineer-in-Charge.

2nd class half brick masonry using common burnt clay building brick in superstructure in cement mortar 1:4 (one cement: four sand) including all leads and lifts of material as directed by the Engineer-in-Charge.

Providing and fixing anodized aluminium and dyed to required shade work for doors, windows, ventilators and partitions with extruded built up standard tubular and other sections of approved make conforming to IS-733 and IS-1285 anodized transparent or dyed to required shade according to IS-1868 (minimum anodic coating of grade AC-15). Fixed with rawl plug and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, wherever required including cleat angles, aluminium snap beading for glazing/paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the direction of Engineer-in-Charge (Jindal / Hindalco make).

a) For doors, windows ventilators & glazed partition frames.

b) For shutters of doors, windows and ventilators including providing and fixing hinges pivots and making provision for fixing of fittings. Where ever required including the cost of PVC/neoprene gasket required (fittings and glazing / paneling shall be paid for separately.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partition etc. with PVC/ neoprene gasket etc. complete as per architectural drawing and the directions of Engineer-in-Charge (cost of aluminium snap beading shall be paid in basic item). a). Glass panes of 5.5mm thickness (weight not less than 13.75 Kg/Sqm).

Providing and fixing anodized aluminium sliding door bolt anodized transparent or dyed to required colour and shade with bolts and nuts screws etc. complete including all leads and lifts as directed by the Engineer-in-Charge. a) 250 x 16mm (two hundred fifty into sixteen milimetre).

Providing and fixing aluminium tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etc. complete including all leads lifts of material as directed by the Engineer-in-Charge.

a). 150x10mm (one hundred fifty into ten milimetre)

b). 100x10mm (one hundred into ten milimetre)

Providing and fixing aluminium handles anodized transparent or dyed to required colour and shade with necessary screws etc. complete including all leads and lifts of material as directed by the Engineer-in- Charge.

a) 125mm (one hundred twenty five milimetre)

b) 100mm (one hundred milimetre)

Providing and laying jointless ceramic tiles 8mm thick in flooring & treads of steps laid on a bed of 12mm thick cement mortar 1:3 (One cement: three sand) finished with flush pointing in white cement complete in all respect (Kazaria / Nitco / johson 1st quality make).

White / coloured glazed jointlesss tiles 8mm (eight milimetre) thick in skirting risers of steps and dado 12mm (twelve milimetre) thick cement plaster 1:3 (one cement : three sand) and jointed with white cement slurry including all leads and lifts of material as directed by the Engineer-in-Charge (Nitco/ Johnson / Kazaria make 1st quality).

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete / stone / plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for metling the surface complete in all respect as per satisfaction of Engineer-in-charge.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after thoroughly cleaning the surface to remove all dirt, dust & other foreign matter etc. including sand paper smooth complete in all respect as per satisfaction of Engineer-in-charge.

6mm (six milimetre) cement plaster to ceiling in cement mortar 1:3 (one cement: three sand) complete in all respect as per satisfaction of Engineer-in-charge

15mm (fifteen milimetre) cement plaster in single coat in fair/rough side on brick concrete/stone walls for interior/exterior plastering with all height including arises internal rounded angles chamfers and/or rounded angles not exceeding 80mm (eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement: six sand) including all leads and lifts and material as directed by the Engineer-in-Charge.

Providing plinth protection 50mm (fifty milimetre) thick in cement concrete 1:3:6 (one cement: three sand: six graded stone aggregate) 20mm nominal size including finishing the top surface of concrete smooth including all leads and lifts of material as directed by the Engineer-in-Charge.

Providing under layer for plinth protection of 75mm (seventy five milimetre) thick unconsolidated bed of dry bricks/ stone aggregate 40mm (forty milimetre) nominal size) well rammed and consolidated and grouted with fine sand including preparation of ground including all leads and lifts of material as directed by the Engineer-in-Charge.

Brick edging (brick laid on edge) to plinth protection with bricks including grouting with cement mortar 1:4 (one cement: four sand) with brick size 22.9 x 11.2 x 7cm (twenty two point nine x eleven point two x seven centimetre) including all leads and lifts of material as directed by the Engineer-in-Charge.

Providing and fixing to wall ceiling and floor galvanized mild steel tube (medium grade) tube fittings and clamps including making good the wall, ceiling and floor complete in all respect as per satisfaction of Engineer-in-charge Jindal / Surya make.

a) 15mm nominal bore

b) 25mm nominal bore

Making connection of galvanized steel distribution branch with galvanized mild steel main 20mm to 40mm nominal bore by providing and fixing tee including cutting and threading the pipe complete including all leads, lifts and carriage of material complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing vitreous china wash down water closet (European type WC pan) with integral ‘P’ or ‘S’ including jointing the trap with soil pipe in cement mortar 1:1 (one cement: one sand) complete in all respect as per satisfaction of Engineer-in-charge (Seat and cover to be measured and paid for separately) Cera / Hindware make. a) Ordinary closet

Providing and fixing plastic seat (Solid/Hollow type) art cover for wash down water closet with C.P. Brass hinges and rubber buffers complete in all respect as per satisfaction of Engineer-in-charge (Cera / Hindware make). a)Solid type Black or white plastic seat and cover

Providing and fixing vitreous China division plate for urinal complete in all respect as per satisfaction of Engineer-in-charge Cera / Hindware make. a) 600mmx330mm size

Providing and fixing vitreous china wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings complete in all respect as per satisfaction of Engineer-in-charge Cera / Hindware make. a) Flat back 550x400mm

Providing and fixing Vitreous china pedestal for wash basin complete recessed at the back for the reception of of pipes and fittongs etc. complete in all respect as per satisfaction of Engineer-in-charge Cera / Hindware make

Providing and fixing C.P. brass waste for wash basin or sink complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing 600x450mm beveled edge mirror of superior glass mounted on 6mm thick A.C. sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screw and washers complete in all respect as per satisfaction of Engineer-in-charge.

Providing & fixing 600mm X 120mm glass/Acrylic shelf with C.P. brass bracket & guard rail complete fixed to wooden plugs with C.P. brass screws complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing C.P. brass bib tap with capstan head complete in all respect as per satisfaction of Engineer-in-charge Smile / Seiko / Spartan make. a) 15mm dia

Providing and fixing C.P. Brass pillar tap with capstan head complete in all respect as per satisfaction of Engineer-in-charge Smile / Seiko / Spartan make. a) 15mm dia

Providing and fixing C.P. brass angle valve without nuts and pipe complete in all respect as per satisfaction of Engineer-in-charge. Smile / Seiko / Spartan make. a) 15mm dia

Providing and fixing PVC connection pipe with brass union complete in all respect as per satisfaction of Engineer-in-charge. a) 45cm length i) 15mm nominal bore.

Providing and fixing brass full way valve with wheel complete in all respect as per satisfaction of Engineer-in-charge. i) 25mm nominal size

Providing and fixing P.V.C. water storage tank of ISI : 12701, GI inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hosting upto all height above ground level complete in all respect as satisfaction of Engineer- in-charge Sintex make Double layer. a) 2000 ltr. net capacity tank

Providing and fixing PVC floor trap with grating ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete in all respect as per satisfaction of Engineer-in-charge (Filolex / Vectus / D-Plast Jindal make). a) 110mmx75mm

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Vectus/D-plast make).

a) 75mm dia

b) 110mm dia

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Vectus/D-plast make).

a) 75mm dia

b) 110mm dia

Providing and fixing PVC plain bend ISI marked complete including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Vectus/D-plast make).

a) 75mm dia

b) 110mm dia

Providing and fixing PTMT coloured/white high density polyethylene/poly propylene 10 litres capacity (full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, siphon, 15mm nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and over flow pipe, 40mm dia CP flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) complete in all respect as per satisfaction of Engineer-in-charge (Cera / Hindware make).

Providing and fixing PTMT jet spray of approved quality and colour with one metre tube etc. complete in all respect as per satisfaction of Engineer-in-charge (Prayag make code No. 521 or Equavalent).

Constructing manhole with R.C.C. top slab in 1:2;4 mix (1cement: 2 sand: 4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 (1cement :4 sand : 8 graded stone 40mm nominal size), inside plastering 15mm thick with cement mortar 1:3 one cement: 3 sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix 1 cement:2sand: 4graded stone aggregate 20mm nominal size finished smooth complete including curing and testing complete in all respect as per satisfaction of Engineer-in-charge. a) Inside size 800x800mm and 500mm deep including 600 X 450mm SFRC Man hole cover with frame. i) With 200mm thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3 (1 cement : 3 sand).

Cutting holes through existing brick work including making good the same in C:M 1:6 (1cement:6 sand) per cms depth of cutting complete in all respect as per satisfaction of Engineer-in-charge.i) holes upto and including 400 Sqcm in area.

Providing & fixing wire gauge using galvanized MS wire gauge designation 85 G with wire of dia 0.56mm in aluminium doors, windows, ventilators, shutters and partitions etc. with PVC / Neoprene gasket etc. complete as per the Architectural drawing and the direction of Engineer-in-charge (cost of aluminium snop beading shall be paid in basic item).

Providing & fixing 6mm thick ACP ( Aluminium composite panels) in aluminium doors, windows, ventilators, shutters and partitions etc. with PVC / Neoprene gasket etc. complete as per the Architectural drawing and the direction of Engineer-in-charge (cost of aluminium snop beading shall be paid in basic item).

Providing and fixing aluminium hooks and eyes etc. complete in all respect as per satisfaction of Engineer-in-charge. a) 150mm (One hundred fifty milimetre)

Providing and fixing vitreous China ½ stall urinal including connecting the urinal with water pipe by means of white lead mixed with chopped hamp (waste to measured and paid separately) complete in all respect as per satisfaction of Engineer-in-charge Cera / Hindware make. a) Half stall urinal flat back size 630x400x420mm

Providing and fixing PVC gully trap with grating brick masonry chamber in cement mortar 1:5 and water tight CI cover with frame of 300mmx300mm size (inside) the weight of cover to be not less than 4.53 kg. and frame to be not less than 2.72 kg. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Vectus/D-plast make).a) 110mm dia P type

Providing and fixing P.V.C. waste pipe 32mm dia for wash basin and sink complete in all respect as satisfaction of Engineer- in-charge.

Providing and fixing wall mounted grab bar 304 stainless steel having a size of 750mm into 80 mm into 70mm strong and easy to grip, ideal for bathroom, toilet and wash room etc. complete in all respect as satisfaction of Engineer- in-charge.

Supplying and installation freedm 5000 wheel chair strong steel frame light weight and foldable heavy duty detachable foot rest quick release rear wheels having a size 109 into 70 into 51 cm with seat width 51-56 cm, modal weight 10-40 kg, hight 90-120 cm and max. user weight 125 kg etc. complete in all respect as per satisfaction of Engineer-in-charge.

Rakesh Saklani