Spl repair to bldg no. P-53 at 550 Acre (Govt Md Accn JCOs/OR 12 Qtrs) under GE (East) Ferozepur Cantt

Dismantling floor, hearth or wall tiling including cement mortar beding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

S&F non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in flooring etc set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match with colour of tiles over and incl screed bedding 15mm thick in cm(1:6), complete all as specified and directed.

M & L Glazed Ceramic coloured tiles in vertical surface 350 x 250 x 7mm/450 x 300 x 7 mm thick primium quality over and incl 10 mm thick rendering in CM 1:4 on vertical surfaces, set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match colour of tiles complete all as specified & directed.

M&L machine cut Prepolished kota stone flooring 18-20 mm thick over & including 20mm thick screed bed in cement mortar 1:6, laid jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and directed.

M&L machine cut Prepolished kota stone 16-18 mm thick as in risers of steps, skirting, dado etc over & including 15mm thick rendering in CM 1:6, jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and directed.

M & L for Granite (of any type) tiles 18 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all specified and directed.

Taking down cement plaster from brick walls of any description, racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M & L Rendering/plastering, 15mm thick in cement mortar (1:4) on any face of brick walls or concrete surfaces, using WPC, surfaces finished even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 , finished fair and even without using extra cement etc including taking down cement plaster on brick or concrete surfaces on wall/ ceilling/ stone/ block etc including racking out joint, hacking for key, scrubbing down with water etc and preparing new plastered surfaces and applying two coats of cement base paint over a coat of alkali resistant primer on surfaces of walls and 2mm thick wall care putty with paint roller complete all as specified and directed by Engineer-in-Charge

M&L for rendering 10 mm thick in CM 1:6 over brick /concrete surfaces finished even and smooth without using extra cement etc including taking down cement plaster on brick or concrete surfaces on wall/ ceilling/ stone/ block etc including racking out joint, hacking for key, scrubbing down with water etc and and preparing new plastered surfaces and applying two coats of oil bound distemper paint on surfaces of walls with paint roller over 2mm wall care putty complete all as specified and directed by Engineer-in-Charge

M&L for rendering 5 mm thick in CM 1:3 on ceillng, finished even and smooth etc including taking down cement plaster on brick or concrete surfaces on wall/ ceilling etc including racking out joint, hacking for key, scrubbing down with water etc and preparing newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed by Engineer-in-Charge

M&L for complete removal of existing treatment on surfaces of walls apply two coat of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification using paint roller technology and providing 2mm thick wall care putty and sanding the surface to prepare the surface even and smooth complete all as specified and directed.

M & L for applying two coats of white wash on old Ceiling surface including preparation of surface complete all as specified and directed.

M&L for complete removal of existing treatment on wall/ roof projections including facia, cornices etc by scrapping and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over 2mm thick cement base putty and sanding the surface to prepare the surface even and smooth complete all as specified and directed at any height incuding necessary scaffolding over new/complete removal surfaces, complete all as specified and directed. Contd...14.01/-

M & L for applying two coat of white wash over old surface of walls including preparation of surfaces complete all as specified and directed.

M & L for White wash in three coats on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size not exc 1.50 Sqm each including cutting holes of appropriate size for insertion blocks of cement concrete for hold fasts complete all as specified and directed.

All as per item No 17 here-in-before but size exceeding 1.5 Sqm & not exceeding 4 Sqm each, complete all as specified and directed.

S&F Pressed steel frames made of 1.25mm thick MS sheet of profile 125x60mm for door and window frames with one or more rebates incl lock strike plate, shock absorbers, 20mm dia 60mm long MS conduit for housing of a drop bolt, butt hinges, hold fasts/lugs etc and treating of internal surfaces of chowkhats and hold fasts/lugs with a coat of coal tar or black paint incl hinges, hold fasts/lugs etc including making good jambs portion by providing plaster in CM 1:4 and finishes as per existing complete all as specified and directed.

M & L Pressed steel frames made of 1.25mm thick MS sheet of profile 105x60mm for door and window frames with one rebate including lock strike plate, shock absorbers, 20mm dia 60mm long MS conduit for housing of a drop bolt, butt hinges, hold fasts/lugs etc and treating of internal surfaces of chowkhats and hold fasts/lugs with a coat of coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified and directed.

M & L Cement concrete (1:3:6), type C-1 using 20mm graded stone aggregate as in bed blocks of hold fasts, coping etc including necessary form work complete all as specified and directed.

S&F 35mm thick, 2nd class hard wood (Hollock), glazed and skelton shutters, open rebated and prepared to receive glass/ gauge etc divided in to squares with plain rounded mitered and rebated sash bars any numbers, fitted with cut and mitered beads for securing glass etc size of members as specified in clause 8.24 (a) of MES Schedule Part-I in Section-8, complete all as specified and directed.

S&F 30mm thick, Flush shutters, solid core construction, with partical board core, commercial type on both sides, one face is covered with deco rative face veneer with lipping/ frame to match complete all as specified and directed.

M & L Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

M & L solid panel PVC door shutters 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement and fixed in the frame at site complete all as specified in clause 8 B.2.1 of MES schedule Part-II (2004).

S&F Anodised aluminium powder coated (minimum thickness of powder coating 50 micron) 2 mm thick frame for doors, windows, ventilators with one or more rebates including joining cleats/aluminium beading for fixing incl hinges etc. complete all as specified and directed.

Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 1.30 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.) hinges type B-21 100mm long (2 no.) suitable handle (1no.) complete all as specified and directed. Note:- (i) Aluminium chowkhat /frame, glass,wiremess and aluminium grill shall be measured and paid separately.

S&F 4.8 mm thick sheet glass ordinary quality and glazing fixing with rubber beads in windows/ventilators in square n. exc 0.5 Sqm in each pane complete all as specified and as directed.

S&F 4.0 mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane fixed to aluminium ventilator complete all as specified and directed.

S & F Framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290. Gde-E-165 complete all as specified and directed.

S & F stainless steel Wire cloth galvanised mild steel, 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified and directed.

M & L Painting to new wooden or wood based surfaces of any description, over 10cm width or girth in two coats with synthetic enamel paint over a coat of pink primer including preparation of surfaces complete all as specified and directed.

M & L Painting to new steel surfaces of any description, over 10cm width or girth two coats with synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified and directed.

Preparation of old treated steel surfaces of any description, over 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

S&F Aluminium Anodised handles 150 mm long fixed to doors/windows, complete all as specified and directed.

S&F Aluminium Anodised tower bolts 200 mm long fixed to doors/windows, complete all as specified and directed.

S & F Aluminium Anodised butt hinges, 125 mm long, fixed with galvanised mild steel hinge pin complete all as specified and directed.

S & F Aluminium Anodised Sliding door bolt, 250 mm long with bright bolt not less than 12mm dia with & including minimum of 6 bolts and nuts, four on bolt plate and two on staple plate fixed with galvanised mild steel hinge pin complete all as specified and directed.

Pre-laminated particle board, 18/19mm thick interior grade, having one side decorative lamination (approved shade) and other side balancing white lamination fixed in pelmet boxes, shelves , rebated or flat edges including 6 mm thick teak wood leaping all-round and continuous piano hinges, fixed as in repairs complete all as specified including dismantling of boarding any description, fixed in any position with nails, complete all as specified and directed.

S & F Continous (piano) hinges of mild steel bright finish or electro galvanised with flap (when open) 30mm,fixed with steel screw complete all as specified and directed.

S&F in repair 100mm long hasp and staple, safety type, aluminium anodised including bolt to hinge plate and fixed with screws and fixed complete all as specified and directed.

S&F in repair Water storage tanks 500 liters capacity rotational moulded, triple layer polythene (cyindrical vertical with closed top) hoisting and fixed in position on roofs including dismantling existing water storage tank complete all as specified and directed.

S & F Ball valve of PVC, 20mm bore, high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and directed.

S & F CI Gate valve, 20mm bore, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union fixed in repairs complete all as specified and directed.

S & F 16 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fixed complete to walls and ceilings or laid in floors including fitting like elbow, reducer, tee, union, nipple etc incl taking up or down existing steel water tubing, 15mm bore alongwith connections fixed/laid in any situation, complete all as specified and directed.

All as per item above 45 herein before but 20 mm bore tubing, complete all as specified and directed.

S & F in repair Stop valve fancy type, cast copper alloy chromium plated, 15mm bore, screwed down, high pressure with crutch or butter fly handle complete all as specified and directed.

Ditto as above item 47 but fancy type, chromium plated with long shank and cup (concelled type), complete all as specified and directed.

S & F in repair Bib tap fancy type, cast copper alloy chromium plated, 15mm bore, with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

Supply & Fix in repairs Squatting pan orrissa pattern vitreous china white of size 580mm x 440 mm with integral foot rests including necessary lime concrete and 100 mm bore sand cast cast iron ‘P’ trap with 550 to 600 mm long neck for connecting WC to branch piece with cement joints etc complete all as specified and directed.

S & F Low level flushing cistern, PVC (white), 10 liters capacity, with inlet ball float valve, PVC flush pipe and necessary fixing accessories and connecting to water pipe and EWC etc and fixed in repairs complete all as specified and directed.

S & F PVC connection 15 mm size PTMT nuts of length 450 mm fixed complete all as specified and directed.

S & F in repair PVC waste pipe of 32 mm dia for Wash Hand basin/Urinals/Sink etc complete all as specified and directed.

S & F Swivel shower of CP brass any colour for fixing with 15mm pipe (Minimum weight 40 gms), complete all as specified and directed.

S & F Shelf of PTMT fixed with & including CP brass screws & wooden/Plastic cleats (min. weight 300 gms), complete all as specified and directed.

S&F tubular towel rail, 20mm dia of 600mm long with fancy type brass chromium plated brackets on both sides and fixed with steel screws and wooden/rawl plugs, complete all as specified and directed.

S&F stainless steel sinks 1 mm thick kitchen or laboratory with plugs, washers, CP coupling and including bedding in cement mortar fixed in RCC cooking platform including fixing cantilever brackets and connecting union to pipe overall size 495 mm x 420mm & bowl size 410mm x 330mm x 160mm, complete all as specified and directed.

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches including dismantling CI pipe/any type alongwith fittings of 75 mm dia, below or above ground level, jointed in cement mortar and taking out complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches including dismantling CI pipe/any type alongwith fittings of 100 mm dia, below or above ground level, jointed in cement mortar and taking out complete all as specified and directed.

PVC (SWR) bend (any radius), 110mm bore, diminishing pieces or tapers (larger bore measured) jointed in cement mortar complete all as specified and directed.

All as per item 61 above here-in-before but 75mm bore, complete all as specified and directed.

PVC (SWR), floor trap, 75mm bore, Plain with grating including jointing with solvent cement complete all as specified and directed.

S & F PVC (SWR) junction single, (single T) or double, (double T) equal or unequal 110 mm, complete all as specified and directed.

S&F PVC rain water pipes 110mm bore including fixing to walls with MS clamps including dismantling pipe any type alongwith fittings of 100 mm dia, below or above ground level, jointed in cement mortar and taking out complete all as specified and directed.

Dismantling brick tiles laid in single layer jointed & pointed in cement mortar complete all as specified and directed.

Demolition of mud phuska in roofs, any thickness, including leeping plaster (whether full thickness removed or only a part thereof) complete all as specified and directed.

M&L for Cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in roof padding complete all as specified and directed.

M & L 10mm plaster in CM(1:4) finished even and smooth without using extra cement on bottom layer of batten roof with water proofing compound (in case of re placement of bottom layer tile) complete all as specified and directed. (WPC shall be measured separately)

M&L for water proofing treatment to roof surface including parapet wall comprising with the following course of treatment/ specifications form bottom to top:- (a) Applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 kg per sqm over a coat of bitumen primer @ 0.30 ltr per sqm including preparation of roof surfaces complete all as specified and as directed. (b) One layer of APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified. Polymeric membrane shall be taken to a height of 60 cm (minimum) and then inserted inside the groove of parapet walls and shall be finished by a membrane flashing. Note: (i) Laying of APP based membranes shall be done by torch on method or as per manufacturer's instructions. (ii) A minimum overlap shall be 75mm length wise and 100 mm width wise of polymeric membranes respectively and sealed all overlaps and joints as manufacturer's instructions.

M&L for two coat of aluminium paint over APP membrane complete all as specified and directed.

Demolition of brick work built in cement mortar of any specification and in any position complete all as specified and directed.

M&L for Brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius complete all as specified and directed.

M&L All as per item 73 above here-in-before but using old bricks retrieved from demolition under item no. 72 above here-in-before including cleaning and removal of mortar from old bricks, complete all as specified and directed.

M&L Brick work in cement mortar 1:4 using sub class ‘B’ old size bricks, straight or curved on plan to any radius in half brick thick walls complete all as specified and directed.

Demolition of reinforced cement concrete in any position not described else where complete all as specified and directed.

Cement concrete (1:2:4), type B-0 using 12.5mm graded stone aggregate as in benching, kerbs, mud stop, rounded or chamfered on edges including form work complete all as specified and directed.

M&L for laying APP based polymeric membrane 3mm thick with minimum weight not less than 3 kg/sqm, reinforced with non woven polyster fabric (wt not less than 160 gms/sqm) torching Joints/overlaps with a propane or a butane gas torch,laid with a minimum overlap of 150mm with thermo fusable finish laid/bonded over a coat of hot blown bitumen 85/[email protected]/sqm,over forced application bitumen primer @0.30 litres per sqm,including preparation of plastered surfaces of Sunken portion, complete all as specified and as directed.

M & L rendering 10mm plaster in CM(1:3) finished even and smooth with using extra cement on vertical surface of sunken portion wall and floor with water proofing compound (in case of re placement of bottom layer tile) complete all as specified and directed. (WPC shall be measured separately).

S&F GI pipe 40 mm bore medium grade including fixing to walls as in spouts of sunken portion complete all as specified and directed.

M & L Cement concrete (1:5:10),type E-2 using 40mm graded stone aggregate in foundation filling or above floor and mass concrete complete all as specified and directed.

M & L for PCC (1:3:6) type C2 (20mm graded stone aggregate) 50mm thick as in plinth protection complete all as specified and directed.

M & L for formwork to chullah, hooks, chajjas, troughs and similar work including edges complete all as specified and directed.

M & L for reinforced cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in chajja, supported on walls, beams, roofs, landing, bolconies, canopies and in shelves and like complete all as specified and directed.

M & L for applying bond coat of epoxy bonding agent & cement in 1:1 ratio for bonding old and new concrete on damaged surfaces applying polymer modified mortar in CM 1:3 including mixing of polymer latex additives upto 60mm thickness (Chajjas fins, border etc) (i) Qty of ploymer to be used 15% by weight of the cement. (ii) Use of electrical mixer to get the homogeneous dough on bond coat surfaces. (iii) To achieve required thickness repear this step after 24 hrs as required.(iv) Keep the surfaces moist using water forg for 5 to 7 days etc complete all as specified and as directed. (v) Rate shall be inclusive of all necessary scaffolding for building height up to 24 meters complete all as specified and directed by Engineer-in-CHarge. Make : - Epoxy bonding agent shall be Krishna, Dr Fixit, MC Bauchemie and M/s Cemistik, Sika as directed.

M & L for mild steel 10 mm dia and over TMT bars as in reinforcement cut to length bend to shape required including cranking, hooking at ends and binding with mild steel wire, (anneled) not less than 0.5 mm dia complete all as specified and directed.

M & L for mild steel 08 mm dia and over TMT bars as in reinforcement cut to length bend to shape required including cranking, hooking at ends and binding with mild steel wire, (anneled) not less than 0.5 mm dia complete all as specified and directed.

Factory made 60mm thick pre-cast coloured interlocking tiles PCC (M-35 Nominal Mix) over 25mm thick layer fine sand and grouted with dry sand over and including 75mm thick brick hard core complete all as specified and directed.

S & F providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement : 3 coarse sand), including making good joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opeing opening wherever required complete @ with two coat of synthetic enamel paint over a coat of primer complete all as specified and as directed.

M & L for repairing the edges of concrete chajjas, facias, column & the like by providing PCC (1:2:4) type B-0 including all necessary formwork and/ or provision of rendering 15 mm thick (average thickness) in cement mortar (1:3) with chiken wire mesh, after applying a coat of cement slurry @ 3 Kg/Sqm of surface finished even and fair, surface area not execeeding 600 mm wide, in patches including taking down swoolen/damaged plaster or concrete complete all as spcified and directed.

Taking down carefully existig copper / alumn point wiring for light / fan / bell / socket 5/15 Amp points complete with fitting and fixtures such as switches, sockets, c/ rosess, holders and bracket fittings with battens / conduits / wires, T/L fittings and making good the disturbed surfaces of walls and roofs etc.and to match with existing colour complete all as specified and directed.

Taking down carefully unserviceable main switches and distribution boards with fuses/ MCB's (single phase or three phase) of any capacity, complete all as specified and directed.

Taking down carefully old unserviceable sub main wiring including meters and making good disturbed surfaces and matching with existing complete all as directed and specified

S&F Point wiring complete with 1100 volts grade PVC FRLS insulated unsheathed cable of copper conductor, multi stranded of size 1.5 Sqmm, single core, drawn through & including PVC rigid concealed conduit, medium grade of suitable size (not less than 20mm dia) duly ISI marked with all accessories such as bends, reducers, spacers, saddles, junction boxes, bakelite sheets, sizes for mounting switch/sockets, fan regulators etc complete with and including continuous earth wire of size 1.5 Sqmm, single core, PVC FRLS copper conductor, insulated, unsheathed, stranded (Green colour) connected to common earth dolly complete all as specified and directed for following : (a) One light/fan/bell/Bldg security light point controlled by one single pole one way switch.

All as per item No. 94 here-in-before but One 3 pin 5 Amp socket outlet point controlled by one switch on Independent board, complete all as specified and directed.

All as per item No. 94 here-in-before but One 3 pin 5 Amp socket outlet point controlled by one switch on same board, complete all as specified and directed.

All as per item No. 94 here-in-before but one 15 Amps socket outlet point controlled by one single pole switch one way and wiring with 2.5 Sqmm PVC FRLS insulated, stranded, unsheated copper conductor on independednt board with continuous earth wire of size 2.5 Sqmm green colours PVC FRLS insulated, unsheathed, stranded copper conductor cable, complete all as specified and directed.

All as per item No. 94 here-in-before but one 15 Amps socket outlet point controlled by one single pole switch one way and wiring with 4.0 Sqmm PVC FRLS insulated, stranded, unsheated copper conductor on independednt board with continuous earth wire of size 4.0 Sqmm green colours PVC FRLS insulated, unsheathed, stranded copper conductor cable, complete all as specified and directed.

S&F 6 amps, single pole, one way switch 240V, 50Hz, white in colour, duly ISI marked complete all as specified and directed. Make- Anchor/ Cona/ Plaza.

S&F Switch piano flush type 16 amps, single pole one way, white in colour, duly ISI marked complete all as specified and directed. Make- Anchor/ Cona/ Plaza.

S&F 6 Amps Socket 2 in 1, white in colour, duly ISI marked complete all as specified and directed. Make- Anchor/ Cona/ Plaza.

S&F Socket outlet, UNI, 2 in one 6 Amps & 16 Amps, white in colour, duly ISI marked complete all as specified and directed. Make- Anchor/ Cona/ Plaza.

S&F Bell push flush, type 6 amp single pole one way, white in colour, duly ISI marked complete all as specified and directed. Make- Anchor/ Cona/ Plaza.

S&F Door Bell, AC, 230 volts, single pole, white in colour, duly ISI marked complete all as specified. Make- Anchor/ Cona/ Plaza.

S&F Ceiling rose surface type, 240 volts, 50 Hz, 6A, Pilot 3 plate, white in colour, bakelite 65 x 50mm, 3 terminals duly ISI marked complete all as specified and directed. Make- Anchor/ Cona/ Plaza.

S&F batten holder, 240 volts, 50 Hz, 6A, white in colour, duly ISI marked complete all as specified and directed. Make- Anchor/ Cona/ Plaza.

S&F rotary stepped type electronic fan regulator compatable for BLDC for ceiling fan 1200/1400mm size, 240 volts, 6 Amps, 100W, deluxe, white in colour, duly ISI markedcomplete all as specified and directed. Make- Anchor/ Cona/ Plaza.

Supply and fixing LED light fitting 1 x 20 Watt, 220V, AC decorative with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F LED bulb of 9/10 watts B-22 CDL 3 star 6500K, complete all as specified and directed.

S&F Factory made three phase and neutral Sheet Steel made out of CRCA 1.2 mm thick, powder coated double door vertical distribution board 4 way, dust and vermin proof, fitted with two cover, one screwed cover for incoming and outgoing MCBs and the second for protection of MCBs fitted with colour bus bar of capacity 200 Amps, neutral link, earth bar and din rail suitable for use on 240/415V, 50Hz supply, VTPN DB, partly immersed in wall, including of MCCB 4 pole adjustable thermal & fixed magnetic type 100 Amps, 50Hz, 415 Volts with rupturing capacity 16 KA and making good distrubbed surfaces with matching colour, complete all as specified and directed.

S&F Factory made single phase and neutral Sheet Steel made out of CRCA 1.2 mm thick, powder coated double door vertical distribution board 8 way, dust and vermin proof, fitted with two cover, one screwed cover for incoming and outgoing MCBs and the second for protection of MCBs fitted with colour bus bar of capacity 200 Amps, neutral link, earth bar and din rail. suitable for use on 240V, 50Hz supply, partly immersed in wall and making good distrubbed surfaces with matching colour, complete all as specified and directed.

S&F MCB SPN, 40A - 63Amps, 240 volts, "C" series, 10KA duly ISI marked, in MCB DB, complete with connection testing and commissioning, complete all as specified and directed.

S&F MCB SP, 6A-32 Amps, 240 volts, "B" series, 10KA duly ISI marked, in the MCB DB, complete with connection testing and commissioning, complete all as specified and directed.

M&L for Sub main wiring with two single core 2x6 sqmm FRLS insulated and unsheathed stranded copper conductor alongwith earth wire 6.0 sqmm drawn in FRLS rigid conduit connected to main board complete all as specified and directed (Two runs cable and one number earth wire and suitable FRLS conduit shall measured together as unit length).

S&F exhaust fan heavy duty copper winding with louvers complete of sweep size 300mm, 900 RPM, single phase, with bolts, nuts and washers, size of the bolt 15 cm long 12mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/00.0076 three core from ceiling rose to exhaust fan max 1.5 mtr for giving connection complete all as specified and directed.

S&F exhaust fan PVC duty with louvers complete of sweep size 250mm, 1200 RPM, single phase, with bolts, nuts and washers, including provision of PVC flexible copper cable of size 23/00.0076 three core from ceiling rose to exhaust fan max 1.5 mtr for giving connection complete all as specified and directed.

Cutting holes making good the distributed surface, grouting nuts for fixing of Exhaust fans complete all as specified and directed.

M&L for disconnecting electric meter of any cap and refixing same after rewiring, in meter box including connection, complete all as specified and directed.

S&F Sheet metal Meter Box single door minimum size 35x50x25cm for electric meter Factory made of MS sheets/CRCA sheet duly painted with powder paint and door hinged locking arrangement conforming to IS 5039 of 1983. The electric meter/switch box shall be suitable for fixing one number of electric meter and knock out holes for incoming and outgoing cable. Before the powder paint process the sheet steel shall go through the anti corrosion conditioning process in not less than seven tank process. Concealed in wall, including making good distrurbed surfaces with matching colour, complete all as specified and directed.

Fixing or hanging only ceiling fans height upto 3mtr to 5 mtrs ceiling height of bldg including three core FR PVC Insulated & overall round sheathed flexible with PVC, colour of cores are Red, Black & Yellow/ Green is for earthing. Sheath colour is Black of cable size 23/0.0076 complete all as specified and directed. Note : Ceiling fans obtained/ taking down from item Sr No. 91 as above

Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc as required 4 mm dia galvanised iron or steel wire, complete all as specified and directed.

Earthing complete with galvanized steel plate elecrode of size 60 cm x 60cm x 6.3 mm thick burried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead GI wire of 4mm dia (8 SWG) by means of bolts , nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI earth wire is connected to main switch board and protected by light grade GI pipe of 15 mm bore. provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shallbe provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. Cement concrete chamber of PCC ( 1:3:6 ) type C-2using 40 mm graded stone aggregate.The chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete (1:2:4) type B-1 using 20 mm graded stone aggregate and MS angle iron 50 x 50 x 6 mm frame including two coats of painting over a red oxide to sxposed steel surfaces. excavation in soft / loose soil, returning filling and removal of surplus soil to a distance of 50 mm as directed and shown in Electrical Plate No- 3 of SSR Part-1 (2009).

S&F LED street light fitting toughened glass 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp incl MS/ GI bracket of suitable size with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/ 66 protection, complete all as specified and directed.

Please Enable Macros to View BoQ information