SPECIAL REPAIRS TO CCDT MAINT BLDG NO P A 29 AT ND MBI UNDER GE NW KUNJALI COLABA MUMBAI

Amount

Demolition of cement concrete un reinforced in ground floors and paving not exceeding 15cm thickness below or above GL complete all as specified and directed by Engineer in charge.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for below GL complete all as specified and directed by Engineer in charge.

Taking down chowkats or frames with shutters (w/o taking of shutters from the frame) not exceeding 1.5 Sqm each complete all as specified and directed by Engineer in charge.

Taking down chowkats or frames with shutters (w/o taking of shutters from the frame) exceeding 1.50 but not exceeding 4 Sqm each complete all as specified and directed by Engineer in charge.

Supply & fix 15mm dia tubes medium grade gavanised with all fittings and fixed complete to walls and ceiling or laid in floors complete incl the holes in walls and floors shall be made by drilling with drill or jumper and not by dismantling the brick/concrete and making good with CM (1:3) properly including taking down steel tubing 15 mm bore complete all as specified and directed by Engineer in charge.

Supply & fix 20mm dia tubes medium grade gavanised with all fittings and fixed complete to walls and ceiling or laid in floors complete incl the holes in walls and floors shall be made by drilling with drill or jumper and not by dismantling the brick/concrete and making good with CM (1:3) properly including taking down steel tubing 15 mm bore complete all as specified and directed by Engineer in charge.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed by Engineer in charge.

Material & labour for Applying Polythene film, 50 micron thick, laid on a coat of blown type bitumen of grade 85/25 at the rate of 1.50 Kg per square metre over a coat of bitumen primer @ 0.30 kg per Sqm complete all as specified and directed by Engineer in charge.

Material & labour for 25mm thick cement concrete type B-1, (1:2:4) (20mm graded aggregate) as bed concrete complete all as specified and directed by Engineer in charge.

Dismantling of wall ceiling board (fibre, pulp, insulation, etc) or insulatin board /slab/blankes, any thickness,including cover fillets complete all as specified and directed by Engineer in charge.

Material & labour for false ceiling made out of 600 x 600 x 4 to 6 mm thick ceiling board deep panel suspension system made out of powder coated GI sheet main tee of size 23.50 x 40 x 0.63 mm and cross tee of size 23.50x23.50x0.63 mm and angle size 19 x 19 x 0.63 mm including 3 mm GI wire for suspending both necessary washers nut/cleats/pin hook etc for securing frame work to ceiling to the snap grid including provn of necessary holes/cutting for providing light/fan as required including making necessary recesses/projected pattern complete all as specified and directed by Engineer in charge.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer in charge.

Material & labour for Non skid ceramic coloured tiles 8 to 10 mm thick (Square/rectrangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc over and including 15 mm thick cement screed bed in CM (1:6). set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engineer in charge.

All as per item No 13 above, but as on vertical surface such as skirting, dados and risers over and including 10mm thick backing coat in CM (1:4) complete all as specified and directed by Engineer in charge.

Material & labour for Non skid ceramic coloured tiles 7 to 8mm thick (Square/ rectrangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18Sqm, in floors etc over and including 15 mm thick cement screed bed in CM (1:6). set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engineer in charge.

Material & labour for Glazed ceramic cloured tiles in vertical surface size of each tiles 350 x 250 x 7mm / 450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed in white or cloured cement to match over and including 10mm thick backing coat in CM (1:4) complete all as specified and directed by Engineer in charge.

Material & labour for granite (of any type) 20mm thick machine cut, bedded and jointed with grey cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over and including 15mm thick cement screed bed in CM (1:6) complete all as specified and directed by Engineer in charge.

Rounding to edges of granite one edge, such as in steps, cooking platform and other similar sitution complete all as specified and directed by Engineer in charge.

Demolition of brick work or stone/boulder masonry, built in cement mortar incl all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed by Engineer in charge.

Material & labour for Brick work with old size subclass 'B' bricks, straight or curved on plan exceeding 6m mean radius built in CM (1:6) complete all as specified and directed by Engineer in charge.

Taking down cement plaster on brick work or stone walls, etc incl raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed by Engineer in charge.

Material & labour for rendering 15 mm thick on stone masonry surface or surface other than fair face of brick-work in (1:6) and finished even and smooth with out using extra cement complete all as specified and directed by Engineer in charge.

Material & labour for rendering 20mm thick pre polymer modified readymixed cement based plaster in two coats of 12 mm thick base coat and 8 mm thick finishing/final coat. Polymer modified ready mixed cement based plaster should having minimum composition of cement & sand ((1:4) )using fully treated dry, well graded natural sand confiroming to IS 383 suitable for external plastering having low rebound properties, low water demand for curing properties, mechanical mixing as per with manufacturer and applied over exterior masonry and concrete surfaces incl using richer mix for making corners if necessary incl making grooves of existing size and necessary two legged MS pipe scaffolding as wherever required incl curing required upto Ground plus 4rth floor bldg complete all as specified and directed by Engineer-in-Charge

Supply & fix aluminium window, doors with shutters / frames / partitions made out of extruded powder coated aluminium sections, with sliding or openable shutters including frame & necessary joining cleats, glazing clip, powder coated aluminium snap beading, screws etc complete and also including powder coated aluminium fittings such as cobra hinges, butt hinges, tower bolts hooks and eyes, peg syays and handles including connected items, with and including, making good to the disturbed portion with its original specification, complete all as specified and directed.

Supply & fix in repairs for aluminium anodised Deco grill 7.5 mm size DG-102, fixed to F/H frames, 1.5mm thick, bar size 6.2mm and 7.5mm thick in required sizes complete all as specified and directed.

Supply & fix 12mm thick, glass for door shutters, partitions, shelves etc with and including fitting and fixtures such as glass handles Stainless steel studs, fittings for door pivots etc complete all as specified and directed by Engineer in charge.

Material & labour 100mm thick PCC (1:4:8) type D2 using 40mm graded stone aggregate as in sub base of floors complete all as specified and directed by Engineer in charge.

Material & labour for machine pressed pre-cast concrete interlocking coloured paver block shape and size conforming to IS-15658-2006 of 80mm thickness M-40 grade with grey cement and pigment laid dry over and including sand base 50 mm thick and compacted using vibrator complete all as specified and directed by Engineer in charge.

Supply & fix Solid PVC door frame of size 50mmX47mm made out of 5mm single side prelaminated PVC sheet (edges will be painted to match with prelam sheet) reinforced with MS square tube, suppling & fixing in opening as per specification complete all as specified and directed by Engineer in charge.

Supply & fix factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6mm raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm prelaminated PVC sheet on back face as per specification complete all as specified and directed by Engineer in charge.

Supply & fix 100mm size butt hinges extruded aluminium alloy with galvanized mild steel hinge pin anodised and fixed type C-21 complete all as specified and directed by Engineer-in-Charge

Supply & fix 150mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed on door shutter complete all as specified and directed by Engineer in charge.

Supply & fix 50mm butt hinges meadium weight cold rold, mild steel and fixed complete all as specified and directed by Engineer in charge.

Supply & fix 200mm aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engineer in charge.

Material & labour for 300mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed by Engineer in charge.

Material & labour 5mm thick frosted sheet glass, ordinary quality and glazing with oil putty or beads in square not exceeding 0.50 Sqm in each pane complete all as specified and directed by Engineer in charge.

Supply and fix aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed by Engineer in charge.

S & F Roller/ Venetian Blinds vertical/Horizontal type made out of standard cloth of approved texture with necessary accessories etc. complete all as specified and directed by Engineer in charge.

Material & labour 18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work as in kitchen cabinet boxes complete all as specified and directed by Engineer in charge.

Material & labour for external teak wood lipping, 6mm thick, fixed with nails for 18/19mm thick prelaminated boards complete all as specified and directed by Engineer in charge.

Cutting chases for concealed water tubing or concealed conduit wiring etc. and making good, cutting not exceeding 10cm girth. pinning in, making good to facings where required and pointing in CM (1:3) on brick walls complete all as specified and directed by Engineer in charge.

Supply & fix in repair 15mm bore brass bib taps quarter turn cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed (weight not less than 400gms) complete all as specified and directed by Engineer in charge.

Supply & fix 15mm bore stop cock quarter turn (Concealed type) CP fancy type with, screwed down, high pressure for iron pipes or for unions fixed in repairs (weight not less than 400gms)complete all as specified and directed by Engineer in charge.

Supply & fix CP pillar tap quarter turn cast copper alloy chromium plated fancy type high pressure with or without lettered hot or cold with long screwed shank and fly nut screwed for iron pipe fancy type (weight not less than 400gms) complete all as specified and directed by Engineer in charge.

Supply & fix in repairs vitreous china wash down water closet pan, (pedestal pattern), white, with and including P/S trap, PVC solid type seat & cover etc complete all as specified and directed by Engineer in charge.

Supply & fix in repair vitreous china wash hand basin flat back of size 550x400mm including bracket, brass chromium plated waste coupling of 32 mm bore and padestal complete as fixed. Complete all as specified and directed.

Supply & fix in repair vitreous china squatting pan, 'Orissa' pattern, size 580 x 440 mm, with integral foot rests incl flush pipe, provn of lime concrete bedding complete all as specified and directed by Engineer in charge.

Material & labour sink with drainage board size 915mm x 460mm bowl size 410mm x 160mm made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar or incl fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 160mm complete all as specified and directed by Engineer in charge.

Supply & fix 75mm dia CP shower rose swivel type with & including 460mm long brass CP heavy duty, fixed in repairs complete all as specified and directed by Engineer in charge.

Supply & fix in repair for health faucet (jet) 1 m long PVC tube with wall hook chromium plated fitted to stopcock 15 mm bore complete all as specified and directed by Engineer in charge.

Supply & fix of vitreous china urinal, half stall type complete including providing andfixing plugs bedding urinal against wall in cement mortar in (1:2) securing urinals to plugswith and including 60 mm brass screws, pointing around urinal back in cement , flush pipes, inlet ,outlet etc complete all as specified and directed by Engineer in charge.

Material & labour for 40mm dia waste coupling, PTMT for glazed ware sinks, basin, etc with long shanks and fly, flange end complete all as specified and directed by Engineer in charge.

Supply & fix 10 ltrs capacity PVC low level flushing cistern valve less white or coloured with inlet, bal valve floot and handle incl brackets complete all as specified and directed by Engineer in charge.

Supply & fix PVC connection on pipe 450mm long with brass nut bolt complete all as specified and directed by Engineer in charge.

Supply & fix PVC waste pipe 32mm dia 800mm long with socket suitable for WHB/Sink complete all as specified and directed by Engineer in charge.

Supply & fix 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed by Engineer in charge.

Supply & fix aluminium tubular towel rail 600mm long between flanges, 20mm dia, D type etc complete all as specified and directed by Engineer in charge.

Supply & fix PVC (SWR) Pipe single socketed in any length with rubbering joints laid in trenches or in floor for 110mm dia complete all as specified and directed by Engineer in charge.

All as per item No 59 above but 75mm dia complete all as specified and directed by Engineer in charge.

Supply & fix PVC (SWR) Pipe single socketed in any length with rubber ring joints 110mm dia fixed to walls with clampcomplete all as specified and directed by Engineer in charge.

All as per item No 61 above but 75mm dia complete all as specified and directed by Engineer in charge.

Supply and fixing PVC Bends any radius 110mm dia provided with acess door complete all as specified and directed by Engineer in charge.

All as per item No 63 above but 75mm dia complete all as specified and directed by Engineer in charge.

Supply and fixing PVC (SWR) Junction single T equal or unequal 110mm dia provided with acess door complete all as specified and directed by Engineer in charge.

All as per item No 65 above but 75mm dia complete all as specified and directed by Engineer in charge.

Material & labour for 75mm thick PCC (1:3:6) type C2 using 40mm graded stone aggregate incl finished even and smooth with using extra cement as in plinth protection incl necessary form work to edges complete all as specified and directed by Engineer in charge.

Material & labour for RCC (1:2:4) (nominal mix) type B1 using 20mm graded stone aggregate as in landing, cooking platforms, shelves and the like complete all as specified and directed by Engineer in charge.

Material & labour for RCC (1:2:4) (nominal mix) type B1 using 20mm graded agg as in chajjas complete all as specified and directed by Engineer in charge.

Material & labour for providing precast cement concrete (RCC) nominal mix, (1:2:4) type B1 (using 20mm graded stone aggregate) as in landings, cover slabs (for manholes etc), chullah hoods, chajjas, water troughs hangers, shelves and similar articles with plain faces and setting in cement mortar (1:4) complete with joints to match including necessary form work complete all as specified and directed by Engineer in charge.

Use and waste of formwork to soffits of suspended slabs, landings, shelves and similar work n exc 200mmm thick horizontal or sloping complete all as specified and directed by Engineer in charge.

Material & labour for Mild steel TMT bars 10mm dia and over cut to length bend to shape as required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer in charge.

All as per item No 72 above but 6 to 8mm dia bars complete all as specified and directed by Engineer in charge.

Material & labour for one coat of synthetic enamal paint over old painted wood/wood based surfaces over 10cm width or girth incl preparation of old painted surface complete all as specified and directed by Engineer in charge.

Material & labour for Two coats of synthetic enamal paint over a coat of red oxide primer on steel surfaces over 10cm width or girth incl preparation of new surfaces complete all as specified and directed by Engineer in charge.

Material & labour for one coats of synthetic enamal paint on old painted steel surfaces over 10cm width or girth including preparation of old surfaces complete all as specified and directed by Engineer in charge.

Dismantling of water tanks after removing complete all as specified and directed by Engineer in charge.

Supply and fix Rotational moulded polyethylene water storage loft tanks (cubical in shape close top) capacity 1000 ltrs hoisted and fixed in position complete all as specified and directed by Engineer in charge.

Material & labour for two coat of oil bound distemper over 1mm thick birla white putty including preparation of newly surface etc complete all as specified and directed by Engineer in charge.

Material & labour for one coat of oil bound including preparation of newly surface etc complete all as specified and directed by Engineer in charge.

Material & labour for complete removal of existing treatment and applying one coat of Oil bound distemper over 1mm thick birla white putty including preparation of surface complete all as specified and directed by Engineer in charge.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m deep and getting out in soft/loose soil for shafts, wells, manholes etc not exceeding 10Sqm on plan for sewage line & foundation etc complete all as specified and directed by Engineer-in-Charge

Material & labour for concrete (1:4:8) bed for RCC drain 150mm dia pipe including packing under,and haunchingagainst thesides of pipesafter they are laid and tested complete all as specified and directed by Engineer-in-Charge.

Reinforced concrete pipes 150mm dia, class NP2, laid and jointed complete with collars complete all as specified and directed by Engineer-in-Charge

Material & labour for PCC (1:4:8) type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete in manholes complete all as specified and directed by Engineer-in-Charge.

Material & labour for PCC (1:3:6) type C1 using 20mm graded stone aggregate as in coping, benching and other similar work (location) with weathering slightly rounded edges and throating etc as required with and incl all necessary form work complete all as specified and directed by Engineer-in-Charge.

Material & labour for PCC (1:2:4) type B2 as in mass concrete in surface channel and drain incl forming fair finished cement concrete with using extra cement complete all as specified and directed by Engineer-in-Charge

Returning filling in including, spreading, leveling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed by Engineer-in-Charge.

Removal of surplus soil/excavated materials to a distance n exc 50m and deposited, spreading, levelling where directed by Engineer-in-Charge not exceeding 1.5m above from the starting point complete all as specified and directed by Engineer-in-Charge.

Cutting into existing manholes for connecting new drains,making good to pipe and rendering,cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete (1:2:4) type B-1 smooth finished,and reforming benching as required complete all as specified and directed by Engineer-in-Charge.

Supply & fix mild steel framed work such as in frames gates, grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, framed balusters, walk ways, railings, framework of water tank and similar work con-forming to Fe-290. Gde E-165complete all as specified and directed by Engineer-in-Charge.

Complete removal of existing water proofing treatment of any description in any position including cleaning, wire brushing, watering, removal of debris upto 1500 mtr distance complete all as specified and directed by Engineer-in-Charge.

Material & labour for PCC (1:2:4) type B-1 (Using 20mm graded stone aggregate) as in roof/chajja padding for maintaining roof/chajja slope complete all as specified and directed by Engineer-in-Charge.

M&L for applying a coat of oil based bituminous primer @200gm/Sqm on the prepared plastered roof surface, then apply a coat of blown type bitumen grade 85/25 heated to working temprature @1.20Kg/Sqm as per manufacture instructions . Providing and laying five layered 4 mm thick APP (Atatic poly propylene) modified polyester reinforced water proofing membrane with minimum weight of 4.60 Kg/Sqm as specified here-in-after. The APP membrane shall be laid using LPG torch-on- application of a coat of application with minimum 100 mm side overlap and 150 mm end overlap. The laying of membrane shall be got done through an authorized applicator of manufacturer of the membrane. The APP membrane shall be taken upto minimum 200 mm on vertical surfaces. The edge of the membrane shall be sealed with sealant. The rain water gutter portion shall be finished with cement mortar 1:4 to provide requisite slop towards rain water pipe outlet. A Polypropylene/polyster, Non Woven geotextile fabric of 150 Gsm to be provided over APP Membrane. Notes :- (i) Irrespective of lap the net covered area shall only be measured and paid (ii) The quoted rate shall be deemed to be inclusive of primer for APP membrane and SBR latex complete.

Material & labour for brushing neat cement slurry with 3 Kg of cement per square meter complete all as specified and directed

Material & labour for rendering 20mm thick cement plaster in CM ((1:3)) on roof top surface finished even and fair including WPC by weight of 3% of total cement concrete complete all as specified and as directed. Note :- WPC will be measuerd separately.

Supply only integral water proofing compound.

Material & labour for cement concrete tiles 25Cmx25Cmx22 mm thick, machine pressed, (with grey cement & pigments) set jointed and pointed in neat cement slurry in floors over and including 15mm thick bedding layers in CM (1:3) complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of surface of of walls and applying two coats of acrylic (antifungal) exterior grade paint of over one coat of primer on wall/roof including preparation of newly plastered surface and necessary scaffolding complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of surface of walls and applying one coat of acrylic (antifungal) exterior grade paint of over one coat of primer on wall/roof including preparation of newly plaster surface and necessary scaffolding complete all as specified and directed by Engineer-in-Charge.

Complete removal of existing treatment of walls and applying two coats of acrylic (antifungal) exterior grade paint over one coat of primer on wall/roof including preparation of newly plastered surface and necessary scaffolding complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of Chajjah tops surface clean, free from dust dirt, grease, oil, followed by applying 2 coats of approved Rubberized / polymer water proofing treatment POLY ALK WP or equivalent as approved as per the manufacturer’s specifications complete all as specified and directed by Engineer-in-Charge.

Material & labour for taking down, chipping and removing the loose, split, damaged cement concrete, cement mortor surfaces of RCC Columns, beams, walls, chajjah etc and exposing the reinforced cement, wire brushing and cleaning the exposed steel reinforced bar, applying rust remover over the cleaned re-bar surface wash the re-bar with clean water for removing all rusts from the old re-bar surfaces, fixing new reinforcement for strengthen the members as required, applying two coats of epoxy zinc primer on new and old steel surfaces, saturate the substrate with water applying one coat of polymer modified bond coat on affected concrete surfaces and finally providing polymer modified cement and quartz sand mortor in CM (1:3) mix , 40mm thick in two coats, using polymer as per manufacturer's instructions complete all as specified and directed by Engineer-in-Charge. Make : Dr. Fixit/Sunanda/chemestik/Fosrok Note :- New reinforcement and MS Sections will be measured and paid separately

Material & labour for providing and applying jacketing around columns / beams / other RCC members with Micro concrete (Molith-MC) including all lifts, shuttering, drilling holes and fixing shear anchor / deficient reinforcement as per manufacturer's specification complete all as specified and directed by Engineer-in-Charge. Note: Reinforcement shall be measured and paid separately. Note :- Rates quoted shall be including jacketing, formwork and micro concrete. Make :- Dr. Fixit, STP, Fosroc as approved

Supply & fix welded steel wire fabric, cut to length, fixed to steel members / reinforcement steel, weigh per Sqm not exceeding 4 Kg complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of existing surfaces of roof top, RCC Gutter and parapet wall, crack filling with prime seal chemical and cement @ the ratio of (1:4), applying two coats of water proof chemical (Newcoat of dr. fixit or equivalent) and finally applying a coat of SBR latex and silicon powder paste not less than 2 mm thick complete all as specified and directed by Engineer-in-Charge.

M & L for grouting 12 mm dia holes of 75 mm deep @ 0.6 m c/c Polyurethene injection grouting provided with PVC/MS Nozzles as per manufacturer instructions at junction of beams and columns as co-ordinal points for inserting/pouring by pressure grouting for column, beams and slabs including cutting and sealing with epoxy putty.complete all as specified and directed by Engineer in charge.

Material & labour for micro concrete works in repairs of patches like edges, chajjas, lintels and other RCC members etc complete all as specified and directed by Engineer-in-Charge

Supply only polymer SBR Latex or equivalent as approved. Make:- Dr. Fosrok, Sunanda, Dr. Fixit

Material & labour for erection & dismantling of MS tubular double scaffolding (H frame) upto height of 30m & with necessary brazing, provision of necessary safety equipment to the skilled workers to carry out the work and covering with green cloths for carrying out external face work of walls complete all as specified and directed by Engineer-in-Charge

Taking down carefully old unserviceable point wiring copper/Aluminum (light/ fan /sockets/power) complete with switches, sockets, ceiling roses, lamp holders, brackets, removing material to store for keeping in safe custody and making good to disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

Dismantling/taking down old unserviceable tube light fittings/building light fitting removing from site and making good the distrubed surface matching with existing surface complete all as specified and directed by Engineer-in-Charge.

Taking down old unserviceable MCB DBs complete with MCBs, isolator/earth metal clad box etc of any type and capacity from wall/ceiling etc & making good to the disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

Taking down Submain wiring any size and any run complete and making good the distrubed surface matching with existing surface complete all as specified and directed by Engineer-in-Charge.

Material & labour for hanging ceiling fan/Exhust fan in position & re-comissioning the same including provision of cable from ceiling rose , making electric connection and testing complete all as specified and directed by Engineer-in-Charge.

Supply & fix exhaust fans in metalic body with powder coated paint , Single piece plastic blade AC Single Phase 230 V capacitor run motor of size 300 mm sweep (Heavy duty), including louvers/shutter and connecting up 3 core flexible cord of size 23/0.0076mm from ceiling rose to exhaust fancomplete all as specified and directed by Engineer-in-Charge. Make :- Usha, Bajaj & Crompton

Taking down and overhauling of ceiling fan of any size make dismantling parts,properly cleaning/removing old existing grease,oil and applying new oil grease,rewinding,cleaning dust,rust and replacing petty items with new as required such as nuts,bolts,washer,bushes,ball bearing,cap,capacitor 2.5 mfd,making the fan serviceable complete all as specified and directed by Engineer-in-Charge.

Refixing/Hanging only ceiling fans with replacement of rubber washers,nut bolts,locking pin connecting and reassembling with copper conductor multi stranded 3 core wire of size14/0.0076 and testing and refixing at site complete all as specified and directed by Engineer-in-Charge.

Supply & fix on replacement of hanger clamp assembly of down rod for hanging of ceiling fan with nuts,bolts,washers & split pin complete all as specified & directed by Engineer-in-Charge

Material and labour for point wiring complete with PVC insulated, unsheathed cable, 1100 volts grade with multistranded copper conductor of 1.5 sq mm (FRLS) drawn through and including PVC casing and caping of suitable size fixed on wall including PVC insulated unsheathed multistranded copper conductor of size 1.5 sq mm (FRLS) as earth continuity conductor and connecting to common earth dolly all as specified for :- Notes :- (a) Colour coding shall be followed as given below:- (i) Phase - Red (ii) Neutral - Black (iii) Earth - Green b) Electrical wiring above false ceiling shall be drawn through medium grade PVC conduit.

One light point controlled by one 5A switch

One Fan point controlled by one 5A switch

One Bell point controlled by one bell push

One 5A flush type switch socket point on same board board

One 5A flush type switch socket point on independent board

All as per item No 120 above but 2.5 Sqmm for phase and neutral and 1.5 Sqmm for earth continuity conductor copmplete all as specified and directed by Engineer-in-Charge.

Material & labour for point wiring complete with 4 Sq.mm single core multistranded PVC insulated & unsheathed copper conductors cable 1100 volts FRLS grade ISI make drawn through & including PVC non metallic casing and capping with Accessories fixed on wall/ceiling/truss etc with metallic ISI make terminal boxes fix on wall including one PVC insulated & unsheathed multistranded copper conductor 4.0 Sq. mm as earth continuity conductor connected to common earth dolly for single board having 2 x 5 Amps and 1 x15 Amp switch socket point on the same board ( for Computer ) complete all as specified & directed. Notes :- (a) Colour coding shall be followed as given below:- (i) Phase - Red (ii) Neutral - Black (iii) Earth - Green b) Electrical wiring above false ceiling shall be drawn through medium grade PVC conduit.

Supply & fix in repair sub main wiring with cable of size 10 sq mm 2 core FRLS PVC insulated unsheathed cable, 1100 volts grade with multistranded copper conductor alongwith earth wire of 6 sq mm single core of FRLS PVC insulated unsheathed cable, 1100 volts grade with multistranded copper conductor including PVC conduit of suitable size complete all as specified and directed by Engineer-in-Charge.

All as per item No 123 above but of size 2 x 6.0 Sqmm + 1 x 6.0 Sqmm size in PVC casing caping of suitable size complete all as specified and directed by Engineer-in-Charge.

All as per item No 123 above but of size 2 x 4.0 Sqmm + 1 x 4.0 Sqmm size in pvc casing caping of suitable size complete all as specified and directed by Engineer-in-Charge.

Disconnecting & taking down old unservicable cable & Supply and lay in repair cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sq mm 3½ core complete all as specified and directed by Engineer-in-Charge.

Disconnecting & taking down old unservicable cable & Supply and lay and drawing cable through cable tray XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3½ core complete all as specified and directed by Engineer-in-Charge.

Supply & fix GI cable tray perforated type 2mm thick of size 150 x 50mm to be fixed on any wall (brick/srione) vertically/horizontally including all accessories complete bending, shaping, drilling, welding, cutting & all fixing arrangement "SNP controls" /National or equivalent. Make : SNP control/National or equivalent as approved by GE.

Supply & fixing pre fabricated GI clamp suitable for fixing/supporting 150x50mm size cable trays complete with buzzer bolts/hold fastener complete all as specified and directed by Engineer-in-Charge. Note :- Contractor quoted rates deemed to be included, the making good to the disturbed surfaces to match with the existing surface.

Supply & fix in repair MCB DB double door SPN 12 Way with 200 Amps rated copper bus bar complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repair MCB DB double door SPN 4 Way with 200 Amps rated copper bus bar complete all as specified and directed by Engineer-in-Charge.

Supply & fix sheet metal enclosure TPN DB VTPN 6 Way,415V with 250A copper busbar, double door type IP-54 protection incl 160Amp MCB's all as specified and directed by Engineer-in-Charge Make: Siemens/Legrand cat No 507751/ABB/C&S Note : DBs shall be concealed in wall where ever posible including making good the surface to match with surrounding complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repair MCCB 160Amps 3pole,25 KA, DPX3 with Thermal magnetic of make Legrand Cat part No 420057 - 1 Nos complete all as specified and directed by Engineer-in-Charge.

Supply & fix MCB TP 63 Amps 16 KA cat part No 408661 of make legrand and equvilent Make: Siemens/Schinder complete all as specified and directed by Engineer-in-Charge.

Supply & fix sheet metal enclosure TPN DB VTPN 4 Way,415V with 250A copper busbar, double door type IP-54 protection incl 160Amp MCB's all as specified and directed by Engineer-in-Charge Make: Siemens/Legrand cat No 507750/ABB/C&S Note : DBs shall be concealed in wall where ever posible including making good the surface to match with surrounding complete all as specified and directed by Engineer-in-Charge.

Supply & fix in Repair MCCB 125 Amps 4 pole, 25 KA, DPX3 with Thermal magnetic of make Legrand Cat part No 420057 - 1 Nos complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repair MCB DB double door SPN 8 Way with 200 Amps rated copper bus bar complete all as specified and directed by Engineer-in-Charge.

Supply & fix MCB SPN 63 Amps complete all as specified and directed by Engineer-in-Charge.

Supply & fix MCB SP 6-32 Amps complete all as specified and directed by Engineer-in-Charge.

Material & labour for shifting of AC unit from the existing postion and refixing in new postion incl additional accessoraies as required, testing and commissioning all as directed by Engineer-in-Charge

Material & labour for taking down of split/window AC unit from the existing postion and after complete the B/R work again refixing same location incl servicing filter cleaning incl necessary fitment additional accessoraies as required, testing and commissioning all as directed by Engineer-in-Charge

Supply & fix ceiling rose surface bakelite 65 x 50mm, flush type, 3 terminals complete all as specified and directed by Engineer-in-Charge

Supply & fix Bell push flush type 5A , 240 volts complete all as specified and directed by Engineer-in-Charge.

Supply & fix bell AC 230V SP 50 Hz musical type complete all as specified and directed by Engineer-in-Charge.

Supply & fix modular switch 1 way 6A complete all as specified and directed by Engineer-in-Charge. Make: Roma/Legrand

Supply & fix modular socket, 6A - 2/3 pin combined 2 modules complete all as specified and directed by Engineer-in-Charge.

Supply & fix for modular fan regulator fan step regulator, 120W - 2 modular step type complete all as specified and directed by Engineer-in-Charge.

Supply & fix modular switch socket combination 16A,6 pin,3 module complete all as specified and directed by Engineer-in-Charge.

Supply & fix modular switch 1 way 16A,1 module complete all as specified and directed by Engineer-in-Charge. Make: Anchor/Roma/Legrand.

Supply & fix modular white cover plate suitable for 4 modules with frame complete all as specified and directed by Engineer-in-Charge.

Supply & fix modular flush box suitable for 4 modules complete all as specified and directed by Engineer-in-Charge.

Supply & fix modular flush box suitable for 6 modules complete all as specified and directed by Engineer-in-Charge.

Supply & fix modular white cover plate suitable for 6 modules with frame complete all as specified and directed by Engineer-in-Charge.

Supply & fix modular flush box suitable for 8 modulescomplete all as specified and directed by Engineer-in-Charge.

Supply & fix modular white cover plate suitable for 8 modules with frame all as specifed and directed by Engineer-in-Charge

Supply & fix modular flush box suitable for 18 modules all as specified and directed by Engineer-in-Charge Make Legrand Cat No 689078 or equivalent as approved by GE

Supply & fix modular white cover plate suitable for 18 modules with frame all as specifed and directed by Engineer-in-Charge Make Legrand Cat No 673500 or equivalent as approved by GE

Supply & fix decorative pendants,thread type, (2 No) 2 x 1.50 metre long parallel 20 mm dia galvanised or stove enamelled screwed steel conduit with two check nuts for fixing tube light fitting and up to 1.5 mtr long twin core 0.5 sq mm copper conductor cable complete all as specified and directed by Engineer-in-Charge.

Supply & fix MS arms bracket (BEST-Pattern) for mounting one in Nos Street/Building security light fitting 40 mm medium grade GI at an angle of 30 degree including clamp/nut/bolts & washers to brace the same properly with duly painted in synthetic enamel paint of two coat in silver colour complete all as specified & directed by Engineer-in-Charge Note :- Contractor rates deemed to be included for making good to the disturbed surfaces to quoted match with the existing surface.

Supply and fixing in repair LED street light/bldg secuirty lights 60 W elegantly designed highly efficient high power LED security light with pressure die cast aluminium housing, reflector enclosed with toughened glass, IP66 protection roadway light complete all as specified and directed. Make : Bajaj /Havells/CG/Surya/Shakti .

Supply and fixing in repair new generation recessed LED 2X2 Luminaire 34 watt to enhance the delight of occupants with comfertable experience through GX with classical design and glare free with soft illumination of make bajaj cat part no BZRSLLGX34WCW or Equivalent make of phillips & Havells as approved by GE

Supply and fixing in repair new generation recessed LED 2X2 Luminaire 34 watt to enhance the delight of occupants with confertable experience through GX with classical design and glare free with soft illumination of make bajaj cat part no BZSSOL36WLEDWH or Equivalent make of phillips & Havells as approved by GE

Supply and fixing in repair new generation suspension mounted BPTX28W LED 4F WH pendant Luminaires and high translucent diffuser provides high quality ecomonic energy saving lighting incl suspension of 1.5mtr (set of 02 Nos) complete fixing arrangement complete all as specified and directed by Engineer-in-Charge. Make :- Bajaj / CG/Surya/ Philips or Shakti.

Supply and fixing in repairLED Batten 40 watt for surface and pendent application anodized extruded alluminium housing high trans misstivity diffuser and high lumen output of make Bajaj cat part no BCLAB40W and Equivalent make of Surya/phillips or Havells. Make : Bajaj / CG/Surya/ Philips or Shakti.

Supply & fix Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20A complete all as specified and directed by Engineer-in-Charge.

Earthing complete with galvanised steel earth plate electrode 600x600x6mm thick buried directly in ground (earth pit not less than 2.25 mtr below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level connected to galvanised earth wire of size 4mm dia means of bolts, nuts check nut & washers of galvanised iron or steel & connected to main switch including complete excavation and earth work in soft/loose soil and disposal of surplus soil to a distance not exc 50 meters, PCC Chamber (1:3:6) type C-2 precast RCC cover with frame, funnel wire mesh, 20mm bore light grade galvanised iron or steel pipe for water, charcoal or coke and salt in alternative layers of 15cm compacted thickness all round the earth electrode complete alll as shown in electrical plate No 3 of SSR part-I including welding with suitble electrode and testing complete all as specified and directed by Engineer-in-Charge. Note : 4mm dia GI wire shall be arc welded to GI plate electrode.

Material & labour for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire complete all as specified and directed by Engineer-in-Charge.

Earthing continuity galvanised iron strip 25 x 4 mm or main earthing lead fixed to wall with clamps or recess or croses or buried in ground or drawn in conduits/pipe or fixed to poles or any other indicated situation for loop earthing etc as required complete all as specified and directed by Engineer-in-Charge.

Material and labour in repairs for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. complete all as specified and directed by Engineer-in-Charge.

Supply & fix pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, chajjas, valley gutter, ridge and fixed with crumple joint etc fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge

Supply & fix for rolled mild steel sections of grade Fe410-W, (Gde-E-250) quality-A for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, Tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and directed by Engineer-in-Charge.

All as per item No 171.00 above but MS plates (Plain or Chaquered) complete all as specified and directed by Engineer-in-Charge.

Supply & fix for Rolled mild steel sections of Grade Fe 410-W, (Gde-E-250) quality-A, as in stairs (framed) including stringers, treads, landing, balusters, hand rail etc, including cleats, brackets etc complete all as specified and directed by Engineer-in-Charge.

Garima Construction Co

jalandhara construction

Shetty Construction Co