REPAIR/REPLACEMENT OF PUMPS SETS MOTORS CERTAIN CONNECTED E/M WORKS TO WATER/SEWAGE SUPPLY INSTALLATION UNDER AGE E/M (W) OF GE (W ) AGRA

Amount

Checking of LT Panel/Motor/Pump set for detecting any kind of fault and attending the fault immediately at any time round the clock and carry out certain repairs required as per site requirement and replacing of worn out parts by expert engineer complete all as directed. Note :- Unit rate includes detecting of any kind of fault in LT Panel/Motor/Pump set only and cost of replacement of worn out parts shall be measured and paid separately under respective items of BOQ

Supply and fix in replacement Direct online starter for 2HP submersible pump, confirming to IS/ IEC 60947-4-1, IP-54, 415 Volt ,extended wide band coil with FRLS internal wiring, star type-Air break and class H insulation complete all as specified and directed by engr-in-charge. Model: IHHDOLHA*E, Make :Havells

Supply and fix in replacement Direct online starter for 5HP submersible pump, confirming to IS/ IEC 60947-4-1, IP-54,415 Volt, extended wide band coil with FRLS internal wiring, star type-Air break and class H insulation complete all as specified and directed by engr-in-charge. Model: IHHDOLLA*E, Make :Havells

Supply and fix in replacement Direct online starter for 7.5HP submersible pump, confirming to IS/ IEC 60947-4-1, IP-54,415 Volt, extended wide band coil with FRLS internal wiring, star type-Air break and class H insulation complete all as specified and directed by engr-in-charge. Model: IHHDOLMA*E, Make :Havells

Supply and fix in replacement fully automatic star delta starter for 10 HP submersible pump, confirming to IS/ IEC 60947-4-1, IP-54,415 Volt, extended wide band coil with FRLS internal wiring, star type-Air break and class H insulation complete all as specified and directed by engr-in-charge. Model: IHHASDRA* :Havells

Supply and fix in replacement fully automatic star delta starter for 12.5 HP submersible pump, confirming to IS/ IEC 60947-4-1, IP-54,415 Volt, extended wide band coil with FRLS internal wiring, star type-Air break and class H insulation complete all as specified and directed by engr-in-charge. Model: IHHASDTA*, Make :Havells

Supply and fix in replacement fully automatic star delta starter for 15 HP submersible pump, confirming to IS/ IEC 60947-4-1, IP-54,415 Volt, extended wide band coil with FRLS internal wiring, star type-Air break and class H insulation complete all as specified and directed by engr-in-charge. Model: IHHASDTA*, Make :Havells

Supply and fix in replacement fully automatic star delta starter for 20 HP submersible pump, confirming to IS/ IEC 60947-4-1, IP-54,415 Volt, extended wide band coil with FRLS internal wiring, star type-Air break and class H insulation complete all as specified and directed by engr-in-charge. Model: IHHASDUB*, Make :Havells

Supply and fix in replacement fully automatic star delta starter for 25 HP submersible pump, confirming to IS/ IEC 60947-4-1, IP-54,415 Volt, extended wide band coil with FRLS internal wiring, star type-Air break and class H insulation complete all as specified and directed by engr-in-charge. Model: IHHASDVB*, Make :Havells

Supply and fix in replacement 3 Pole Power contractors with AC coil, rating 18 Amps, conforming IS/ IEC 60947-4-1, IP-20,415 Volt, snap fit construction, nut retaining washer for quick termination and class H insulation complete all as specified and directed by engr-in-charge. Model No.IHPHA018110 , Make: Havells

Supply and fix in replacement 3 Pole Power contractors with AC coil , rating 25 Amps, conforming IS/ IEC 60947-4-1, IP-20,415 Volt, snap fit construction, nut retaining washer for quick termination and class H insulation complete all as specified and directed by engr-in-charge. Model No.IHPHA025210 , Make: Havells

Supply and fix in replacement 3 Pole Power contractors with AC coil, rating 32 Amps, conforming IS/ IEC 60947-4-1, IP-20,415 Volt, snap fit construction, nut retaining washer for quick termination and class H insulation complete all as specified and directed by engr-in-charge. Model No.IHPHA032201 , Make: Havells

Supply and fix in replacement 3 Pole Power contractors with AC coil, rating 150 Amps, conforming IS/ IEC 60947-4-1, IP-20,415 Volt, snap fit construction, nut retaining washer for quick termination cassette type design and universal coil , cases and class H insulation complete all as specified and directed by engr-in-charge. Model No.IHPHA150500 , Make: Havells

Supply and fix in replacement 3 Pole Power contractors with AC coil, rating 225 Amps, conforming IS/ IEC 60947-4-1, IP-20,415 Volt, snap fit construction, nut retaining washer for quick termination cassette type design and universal coil , cases and class H insulation complete all as specified and directed by engr-in-charge. Model No.IHPHA150500 , Make: Havells

S&F in repair thermal over load relay type MN suitable for MNX contactors relay range 90-150 Amps including fixing arrangement complete all as specified and directed.

S&F in repair thermal over load relay type MN suitable for MNX contactors relay range 9-15 Amps including fixing arrangement complete all as specified and directed.

S&F in repair thermal over load relay type MN suitable for MNX contactors relay range 22-32 Amps including fixing arrangement complete all as specified and directed.

S&F in repair 3 pole power contactors of rating 9 Amps MNX 9 including fixing arrangement suitable complete all as specified and directed.

S&F in repair 3 pole power contactors of rating 12 Amps MNX 12 including fixing arrangement suitable complete all as specified and directed.

Dismantling of defective submersible pump set 10-15 HP with column assembly, pump bowl assembly of any size/capacity including disconnecting electrical and water line connection complete with lifting it with the help of chain pulley, clamp tripod and reassembling after repairing by lathe work and other machinery work as required and replacement of studs, nuts, bolts etc including re-fixing the same after making it serviceable in its existing position complete all as specified and directed.

All as per item No 20 here-in-before but pump set capacity 5 to 7.5 HP

All as per item No 20 here-in-before but pump set capacity 1 to 3 HP Note for item No. 20 to 22 (i) Defective spares for pump and column assembly shall be measured and paid separately under respective item here-in-after. (ii) After taking out submersible pump set for repair, contractor shall cover the tubewell with cap to avoid any accident. (ii) Defective spare parts of bowl assembly shall be measured and paid separately under items here-in-after.

Supply Only following Parts for replacement of defective parts of pump set repaired under item No. 20 to 22 above.:- NOTE : The cost of labour components deemed to be included in the rates quoted for item No. 20 to 22 above

Gun Metal Impeller suitable for 10 to 15 HP complete all as directed

Intermediate bowl suitable for 10 to 15 HP complete all as directed

Bowl bush rubber suitable for 10 to 15 HP complete all as directed

Bowl bush (Gun metal) suitable for 10 to 15 HP complete all as directed

Cast iron impeller seal ring (neck ring) suitable for 10 to 15 HP complete all as directed

Stainless steel running sleeve (Off sizes) suitable for 10 to 15 HP complete all as directed

Pump shaft 25.4mm dia suitable for 10 to 15 HP Pump complete all as directed

CI Impeller suitable for 5 to 7.5 HP pump complete all as directed

Intermediate bowl suitable for 5 to 7.5 HP pump complete all as directed

Bowl bush rubber suitable for 5 to 7.5 HP Pump complete all as directed

Bowl bush (gun metal) suitable for 5 to 7.5 HP Pump complete all as directed

Cast iron impellor seal ring (neck ring) suitable for 5 to 7.5 HP Pump complete all as directed

Stainless steel running sleeve (off size) suitable for 5 to 7.5 HP complete all as directed

Impellor locking keys stainless steel (off size) suitable for 5 to 7.5 HP Pump complete all as directed

Supply only the PVC impellor suitable for 1 to 3 HP Pump complete all as directed

Intermediate bowl suitable for 1 to 3 HP Pump complete all as directed

Bowl bush rubber suitable for 1 to 3 HP Pump complete all as directed

Bowl bush (gun metal) suitable for 1 to 3 HP Pump complete all as directed

Cast iron impellor seal ring (neck ring) suitable for 1 to 3 HP Pump complete all as directed

Stainless steel running sleeve (Off size) suitable for 1 to 3 HP Pumpcomplete all as directed

Impellor locking keys stainless steel (Off size) suitable for 1 to 3 HP Pump complete all as directed

Dismantling of 01 to 03 HP Capacity defective submersible motor any make, cutting and taking out burnt out winding wire and M&L for rewinding the same with PVC insulated water proof conductor copper wire of best quality of existing gauge & turn and reassembling after replacement of bush, bearing, sleeves, grinding as required and polishing of rotor shaft etc including testing and refixing the same in existing position complete all as specified and directed. Note : Bush/bearing/sleeve/thrust plate shall be measured and paid separately under respective item here-in-after.

All as per item No 23 above but for 05 to 7.5 HP capacity

All as per item No 23 above but for 10 to 12.5 HP capacity

All as per item No 23 above but for 15 HP capacity

Supply Only following Parts for replacement of defective parts of submersible motor repaired under item No. 24 to 27 above.:- NOTE : The cost of labour components deemed to be included in the rates quoted for item No. 24 to 27 above

Bush/bearing (gun metal) suitable for 01-03 HP submersible motor

Bush/bearing (gun metal) suitable for 05/7.5 HP submersible motor

Bush/bearing (gun metal) suitable for 10/12.5 HP submersible motor

Bush/bearing (gun metal) suitable for 15 HP submersible motor

Thrust Plate (gun metal) suitable for 01-03 HP submersible motor

Thrust Plate (gun metal) suitable for 5/7.5 HP submersible motor

Thrust Plate (gun metal) suitable for 10/12.5 HP submersible motor

Thrust Plate (gun metal) suitable for 15 HP submersible motor

S&F in repairs submersible cable PVC insulated copper conductor 1.5 Sqmm 3 core 1100 volts grade complete all as specified and directed

S&F in repairs submersible cable PVC insulated copper conductor 2.5 Sqmm 3 core 1100 volts grade complete all as specified and directed

S&F in repairs submersible cable PVC insulated copper conductor 4 Sqmm 3 core 1100 volts grade complete all as specified and directed

S&F in repairs submersible cable PVC insulated copper conductor 6 Sqmm 3 core 1100 volts grade complete all as specified and directed

M&L for 80mm bore, adopter nipple 50cm long GI flanged or socketed (for connecting column pipe to pump) complete all as specified and directed.

M&L for 100mm bore, adopter nipple 50cm long GI flanged or socketed (for connecting column pipe to pump) complete all as specified and directed.

M&L for coupler for pump and motor of any capacity (submersible pump) complete all as specified and directed .

M&L for motor housing studs of any size complete all as specified and directed.

S&F in repair Cast iron non return valve of size 100 mm bore, ISI marked both ends flanged including rubber gasket, MS bolts, nuts, washers and testing complete all as specified and directed.

S&F in repair Cast iron non return valve of size 80 mm bore, ISI marked both ends flanged including rubber gasket, MS bolts, nuts, washers and testing complete all as specified and directed.

Supply and packing pea gravel of 2mm to 6mm size of approved quality as ordered to pack around the casing/slotted pipes in bore well complete all as specified and directed.

Developing tube wells by compressed air with minimum pressure of 10kg/Sqcm and minimum air discharge 450 CFM all as specified in IS 11189-1985 Para 4.3 complete all as specified and directed. Note : Compressor, pump, pipe and other allied items will be arranged by contractor and no extra payment will made by the department.

S&F MCCB 4 Pole, 415 V, Adjustable type, 160 Amps with breaking capacity 36 KA

S&F MCCB 4 Pole, 415 V, Adjustable type, 200 Amps with breaking capacity 36 KA

S&F MCCB 4 Pole, 415 V, Adjustable type, 250 Amps with breaking capacity 36 KA

S&F MCCB 4 Pole, 415 V, Adjustable type, 350 Amps with breaking capacity 36 KA

S&F MCCB 4 Pole, 415 V, Adjustable type, 400 Amps with breaking capacity 36 KA

S&F in repair single phase preventer for protection for submersible pump against over loading, reverse phase, single phasing complete all as specified and directed.

Taking up centrifugal pump set of following capicity from its foundation at different location of installations by disconnecting electrically and mechanically, transporting it to the workshop for dismantling the pump sets and back to installation after repairing/removing of unserviceable parts complete all as specified and directed.

150 HP Capacity pump set

100/120 HP Capacity pump set

30 HP Capacity pump set

10/12.5 HP Capacity pump set

up to 5 HP Capacity pump set

M & L for re-winding of electric motor of following capicity centrifugal pump sets 3 phase 415 volts 50 Hz AC with super enamelled copper winding wire of existing weight & size incl cleaning of stator slot winding paper fixing starter incl cut x size warnshing and baking complete all as specified & directed by Engr-in-Charge for capacity :-

150 HP Capacity centrifugal pump sets

100/120 HP Capacity centrifugal pump sets

30 HP Capacity centrifugal pump sets

10/12.5 Capacity centrifugal pump sets

up to 5 HP Capacity centrifugal pump sets

Repairing of rotor assembly of following capicity centrifugal motor sets 3 phase 415 volts 50 Hz AC including dismantling and reassembled at site complete all as specified & directed by Engr-in-Charge:-

150 HP Capacity centrifugal motor sets

100/120 HP Capacity centrifugal motor sets

30 HP Capacity centrifugal motor sets

10/12.5 Capacity centrifugal motor sets

up to 5 HP Capacity centrifugal motor sets

M&L for painting of following capicity centrifugal pump sets complete all as specified and directed by Engr - in - Charge including writing SM No. and MES No. on the pump set with paint :-

150 HP Capacity centrifugal pump set

100/120 HP Capacity centrifugal pump set

30 HP Capacity centrifugal pump set

10/12.5 Capacity centrifugal pump set

up to 5 HP Capacity centrifugal pump set

Repairing/overhauling of following capicity centrifugal pump set incl cleaning of inside motor & pump set, oiling greasing, gland packing filling and proper alignment incl repair/replacement of unserviceable part compete all as specified and directed :-

150 HP Capacity

100/120 HP Capacity

30 HP Capacity

10/12.5 Capacity

up to 5 HP Capacity

Supply only following spare parts suitable for 150HP Centrifigal pump set compete all as specified and directed ;-

Ball bearing for motor of existing size

(Ball bearing pump set of existing size

Roller bearing for pump set size

Impeller made out of existing size

Glands bush

Neck Ring

Coupling complete of existing size

Pump shaft incl key

Rubber bush incl nut bolt and washer complete

Supply only following spare parts suitable for 100HP/120HP Centrifigal pump set compete all as specified and directed ;-

Ball bearing pump set of existing size

Roller bearing for pump set size

Impeller made out of existing size

Glands bush

Neck Ring

Coupling complete of existing size

Pump shaft incl key

Rubber bush incl nut bolt and washer complete

Supply only following spare parts suitable for 30HP Centrifigal pump set compete all as specified and directed ;-

Ball bearing for motor of existing size

Ball bearing pump set of existing size

Impeller made out of brass of existing size

Glands bush

Neck Ring

Coupling complete of existing size

Pump shaft incl key

Rubber bush incl nut bolt and washer complete

Supply only following spare parts suitable for 10HP/12.5 HP Centrifigal pump set compete all as specified and directed ;-

Ball bearing of existing sizes and make.

Impeller made out of CI of existing size

Glands bush

Neck Ring

Coupling complete

Pump shaft incl key

Rubber bush incl nut bolt and washer complete

Supply only following spare parts suitable for Up to 5 HP Centrifigal pump set compete all as specified and directed ;-

Ball bearing of existing sizes and make.

Impeller made out of CI of existing size

Glands bush

Neck Ring

Coupling complete

Pump shaft incl key

Rubber bush incl nut bolt and washer complete

Material and labour for column pipe GI 'C' class for bore well 2" dia including threading and all connected works all as directed by Engr-in-Charge. Taking up of motor and lowering will be measured separately.

Material and labour for column pipe GI 'C' class for bore well 3" dia including threading and all connected works all as directed by Engr-in-Charge. Taking up of motor and lowering will be measured separately.

M/S OM Enterprises

M/S SHRINATH CONTRACTION

M/S RADHEY GOVIND ENTERPRISES