InstallationConstruction of Roof Top Rain Water Harvesting Structures at Main Building of Dayanand Vaidik College OraiJalaun.

PREPARATION/CONSTRUCTION OF RECHARGE WELL

350 mm Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level(DSR 23.1.1.2)

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of useable water yield without sand content (beyond permissible limit), with required capacity air compressor running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, including disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.(DSR 23.12)

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of 150 mm dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge (DSR 23.3.2)

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineerin-charge.(DSR 23.4.2) 150 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.(DSR 23.14.2)150 mm dia

Providing & Filling of Pea Gravel of Size 2 mm to 4 mm dia. into bore well including cost of labour, material etc. required for proper completion of work. (UPGWD SOR)

Supply & installation of 150 mm dia casing MS pipe. (DSR Material code 7743, chapter 3 materials)

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell (DSR 23.13.2)150 mm dia

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). (DSR 23.15.2) 150 mm dia

Supply and installation of 150 mm dia MS air vent system. (As per Matket rate)

CONSTRUCTION OF RECHARGE TANK AND FILTER CHAMBER RECHARGE TANK SIZE 4.0x2.0x2.50Mt. AND FILTER CHAMBER SIZE 2.0x2.0x2.50 Mt.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. ( DSR 2.6.1)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :. 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)In foundation & floors. (DSR 4.1.8)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) (DSR 6.1.1 )

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) ( DSR 5.1.3)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. (DSR 5.22.1 Mild steel and Medium Tensile steel bars)

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 20 mm thick (DSR 13.9.2)

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate (DSR 11.3.1)

Filling of Excavated earth in trnches plinth sides of foundation etc. (DSR 2.25)

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. DSR 10.2

Supply and laying 150mm PVC slotted pipe into filter tank. (DSR 7751)

Supply and fixing of Galvenised wire mess of avg width of aperture 1.4 mm and nominal dia of wire 0.63 mm. (DSR 7029)

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge. in filter Tank (DSR 23.7)

Providing & Filling of Pea Gravel of Size 2 mm to 4 mm dia. into bore well including cost of labour, material etc. required for proper completion of work. (UPGWD SOR)

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-incharge in filter Tank(DSR 23.5)

Making provision of overflow system complete in all respect including cost of all materials. (As per Market Rate.)

MS Ladder (As per Market Rate)

Layer of loose Brick (Common burnt clay F.P.S. (non modular) bricks class designation 7.5 DSR: 2602) Non modlar Brick-230*110*70mm

CONVEYANCE PIPE LINE WORK WITH CHAMBERS Supply of PVC pipe conforming IS mark with all required Tee, Coupler, Elbow, Reducer etc.

100 mm dia 6 Kgf/cm2 Pressure PVC Pipe (7758 DSR)

150 mm dia 6 Kgf/cm2 Pressure PVC Pipe (DSR 7745)

200 mm dia 6 Kgf/cm2 Pressure PVC Pipe ( DSR 7746)

Construction of 900x900x900 mm size inlet chamber with class 150 brick work 1:3 cement mortar with RCC slab on top along with proper by-pass arrangement to run-off excess rain water.

Construction of 750x750x750 mm size inlet chamber with class 150 brick work 1:3 cement mortar with RCC slab on top along with proper by-pass arrangement to run-off excess rain water.

Construction of 600x600x600 mm size inlet chamber with class 150 brick work 1:3 cement mortar with RCC slab on top along with proper by-pass arrangement to run-off excess rain water.

Construction of 450x450x450 mm size inlet chamber with class 150 brick work 1:3 cement mortar with RCC slab on top along with proper by-pass arrangement to run-off excess rain water.

Excavating trenches by mechinical / manual means of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m. (DSR 2.10.1.2 Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia)

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. DSR 15.2.1 Nominal concrete 1:3:6 or Richer mix (i/c equivalent design mix)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :. 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)In foundation & floors. (DSR 4.1.5)

Down Pipe and Miscellaneous Work Supply & fixing of new down pipe with all required Tee, Coupler, Elbow, Reducer etc.

100 mm dia 6 Kgf/cm2 Pressure PVC Pipe (7758 DSR)

All required accessories for provision of drained off first rain water flush-out system as per site requirment & instructions. (As per Market Rate)

Fabrication & supply of angle Iron Sign board of frame size 1.20x0.90x1.95 mt. with cross strip & beading of size 30x4 mm welded on frame of MS angle size 40x40x5 mm and MS sheet of 18 gauge as per drawing & design including all labour, material and T&P etc. complete. (As per UPGWD SOR)

Fixing of legs of sign board on cement concrete block of size 0.30x0.30x0.60 mt. in ratio 1:3:6 as per drawing & design including all labour, material etc. complete. (As per UPGWD SOR)

Painting of angle iron sign board with double coat primer and enamel paint of black colour on frame both side and sky blue on MS sheet both side including all labour, material etc. complete. (As per UPGWD SOR)

Writing on angle iron sign board both sides of given matter with Post Office Red Color Fluorescent Paint as per drawing and detail given including all labour, material etc. complete. (As per UPGWD SOR)

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: 13.47.1 New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) (RECHARGE TANK+FILTER CHAMBER+COLLECTION CHAMBERS) (DSR 13.47.1) Calculation =4*(6+0.23*3)*(2+2*0.23) + 11*(0.90+0.46)*(0.90+0.46)+20*(0.750+0.46)*(0.750+0.46)+30*(0.60+0.46)*(0.60+0.46)+50*(0.45+0.46)*(0.45+0.46)

CONSTRUCTION/INSTALLATION OF PIEZOMETER FOR IMPACT ASSESSMENT

Shifting/transportation of trolley mounted DC Rig Machine with its accessories such as drill rods etc. up to site. (As per UPGWD SOR)

Drilling of 200mm Bore Well by DC Rig Machine. (As per UPGWD SOR)

Water Supply Charges for drilling work. (As per UPGWD SOR)

Providing of 100 mm dia CS/CM Casing Pipe (confirming IS :12818) assembly : (DSR 23.3.1 )

Providing of 100 mm dia CS/CM Ribbed Screen Casing Pipe (confirming IS :12818) assembly (DSR 23.4.1)

Providing & Filling of Pea Gravel of Size 2 mm to 4 mm dia. into bore well including cost of labour, material etc. required for proper completion of work. Calculation : 0.785*(0.2*0.2-0.1*0.1)*50=1.178 cumec (As per UPGWD SOR)

Providing and fixing 100 mm dia threaded PVC end cap. (1 No for each well) (As per UPGWD SOR)

Providing and fixing M.S. Pipe of 150mm dia. (confirming IS : 1239) (As per UPGWD SOR)

Providing and fixing 150 mm dia M.S. Clamp (1 Set for each well) (As per UPGWD SOR)

Providing and fixing 200mmx200mm square MS plate including 04 No. Fastner set. (As per UPGWD SOR)

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. ( DSR 2.8.1) calculation : 1.5mx1.5mx0.9m = 2.025 cum (2.025 Cum for each well)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :. 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)In foundation & floors. (DSR 4.1.8) Calculation : 1.5mx1.5x0.15m = 0.3375 cum (150 mm well area -0.017 sq. m) hence deduction =0.017*0.15=0.00255

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) (DSR 5.1.3). 0.8mx0.8mx1.5m + 0.60 m x 0.60 m x 0.15m = 1.014 cumec deduction -0.017*1.65=0.028

Fabrication of Security System as per design. (1 Job for each well) (As per UPGWD SOR)

Development of bore well by 3 HP Compressor. (10 Hrs for each well) (As per UPGWD SOR)

Fabrication and supply of angle iron sign board of frame size 1.20x0.90x1.95 with cross strips and beading of size 30x4mm welded on frame size 10x40x5 mm frame and M.S. sheet of 18 gauge as per drawing and design including all labour and material, etc. reqd. (1 No for each well) (As per UPGWD SOR)

Painting of angle iron sign board with double coat primer and enamel paint of black colour on frame both side and sky blue on M.S. sheet both side (1 Job for each well) (As per UPGWD SOR)

Writing on angle iron sign board both sides of given matter with Post office Red colour Florescent paint as per drawing and design. (1 Job for each well) (As per UPGWD SOR)

Fixing of sign board legs on cement concrete block of size 0.30x0.30x0.60m in ratio 1:3:6 as per drawing and design including all labour and material (2 Per Leg for each well) (As per UPGWD SOR)

loading/unloading & transportation of material , T&P including all labour etc complete. (As per UPGWD SOR)

Tentage charges (as per UP GWD SOR)

Reduced Level survey (as per UP GWD SOR)