SPECIAL REPAIRS TO BLDG NO. T-02 (EM STORE) T-18 (AO OFFICE) OF GE 872 EWS, SPECIAL REPAIRS TO BLDG NO. T-20 OF INF DIV CAMP AND PROVN OF CERTAIN REVENUE AND MINOR WORKS AT LIKABALI MIL STN UNDER GE 872 EWS

Amount

B/R SERVICES/WORKS

Demolition Cement Concrete (un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level) and Removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Demolition Brick Work or Pre-cast Concrete Block Masonry, built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc., complete all as specified and as directed.

Dismantling Timber Scantlings 40 Sq Cm and Over in Section in Unframed Work, Seggregating Serviceable Timber Scantlings and Keep in Safe Custody for Refixing / Reuse, complete all as specified and as directed.

Taking down Chowkat or Frame of any description (without Taking Off Shutter from the Frame) not exc. 1.50 Square Metre Each, complete all as specified and as directed.

Taking down Chowkat or Frame of any description (without Taking Off Shutter from the Frame) of any description, exc. 1.50 Square Metre but not exc. 4.00 Square Metre Each, complete all as specified and as directed.

Taking down/out Unserviceable Rusted/Worn out Wire Cloth/Netting of any description, fixed with Beads, etc., complete all as specified and as directed.

Dismantling Plain or Corrugated Steel Sheeting of any gauge and thickness, Segregating Serviceable Steel Sheeting and Stacking properly at Sites and Keep in Safe Custody for re-use, complete all as specified and as directed.

Dismantling Wall and Ceiling Boards (Fibre, Pulp, Insulation, etc.) or Insulation Boards/ Slabs/ Blankets of any descriptions including Cover Fillets, complete all as specified and as as directed.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing) and removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Taking down Cement Plaster including raking out Joints, hacking for Key, scrubbing down with Water and removing Debris, etc. etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Surface Dressing not exc. 15 Cm Deep in Soft/ Loose Soil and getting out, complete all as specified and as directed.

Surface Excavation not exc. 30 Cm deep and ave. 15 Cm deep and getting out in Soft/Loose soil, complete all as specified and as directed.

Excavation in Trenches not exc. 1.50 Metre wide and not exc. 1.50 Metre in depth for Foundation etc. or for Shafts, Wells, Cess Pits, Manholes, Pier Holes, etc. not exc. 10 Sqm on Plan and not exc. 1.50 Metre in depth and getting out as in Soft/Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering and Well Ramming in layers not exc. 25 Cm, in Soft/Loose Soil, complete all as specified and as directed.

Removing Excavated Materials (Soils) not exc. 50.00 Metre and depositing where directed at a level not exc. 1.50 Metre above the Starting Point, complete all as specified and as directed.

Excavating in Post Holes (or similar Holes) in Soft/Loose Soil, each not exc. 0.50 Cum, getting out including spread and levelled with excavated surplus Soils, complete all as specified and as directed.

M&L Sand Filling (as approved) under Floors or in Foundations in layers not exc. 15 Cm thick including Watering and Consolidation, complete all as specified and as directed.

M&L Hardcore Broken Stone or Boulders, gauge not exc. 63mm, deposited, spread and levelled in layers not exc. 15 Cm thick, watered and well rammed to a True surface, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) in Coping, Bed Plates, Benching, Bed Block, Kerb Stones, etc. including necessary Formwork and Weathering, slightly Rounded or Chamfered Angles and Throating, complete all as specified and as directed. NOTE : Cost of Formwork shall deem to be included in the Quoted Unit Rate.

M&L Cement Concrete 1:3:6 (40mm graded aggregate) for embedding Mild Steel Work as Posts, etc. in Foundations, Filling and Mass Concrete, etc. including necessary Formwork, complete all as specified and as directed. NOTE : Cost of Formwork will deemed to be included in Quoted Unit Rate.

M&L Cement Concrete 1:4:8 (40mm graded aggregate) in Foundations, Filling and Mass Concrete, etc. including necessary Formwork, complete all as specified and as directed. NOTE : Cost of Formwork shall deem to be included in the Quoted Unit Rate.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Foundation including Rafts, Footing, Foundation Beams for Column Basement Slab, under Reamed Piles, complete all as specified and as directed. NOTE : Reinforcement will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Columns, Pillars, Posts and Struts, etc., complete all as specified and as directed. NOTE : Reinforcement will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Beams, Cantilevers, Bressumers, Lintels over 1.50 Metre Span, etc., complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Slabs supported on Walls, Beams and Columns in Floors, Roofs, Landings, Balconies, Deck Slabs and in Shelves and the like, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Chajja, etc., complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Pre-cast Reinforced Cement Concrete 1:2:4 (20mm graded aggregate) in Banches (Chair type) having 100mm thickness, Back Height 1000mm, Back Width 620mm with 05 No. Pre-cast Reinforced Concrete Planks of Size 1500mm x200mmx50mm casted with using M-30 Grade of Concrete including Providing suitable Reinforcement to Prevent damage during Handling, Transportation, Erection for Long Time Uuse. All Parts are jointing together with suitable Size Mild Steel Bolts and Nut and Bolts are to Sealed after Assembly. Seating Height of Bench 450mm, Total Height of Bench 100mm, Bench Top and Planks are treated with Special Anti-corrosive, Water Proof Coating so as to Make the Surfaces Glossy and Water Proof including Erection at Site, complete all as specified and as directed. NOTE : Cost of All Materials including Reinforcement, Formwork, all Labour Elements, etc. will deem to be include in the Quoted Unit Rate.

M&L Formwork to Sides of Concrete Foundations, Footings, Bases of Columns, Raft and Raft Beams, Sides and Soffits (if any) of Foundation and Plinth Beams; and Similar Work; Vertical or to Batter, Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Sides of Pillars, Posts, Struts, Piers, Columns and Stanchions, Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Sides and Soffits of Floor or Roof Beams, Girders, Beam Haunchings, Bress-summers, Lintels, Cantilevers, Shelves including Supports, Overhangs, etc. also splays between Floors and Beams, etc., Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Soffits of Suspended Slabs such as Roof Slabs, Floor Slabs, Landings and Similar Works; not exc. 200mm thick (Horizontal or Sloping), etc., Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Chullah Hoods, Chajjas, Trough and and Similar Items including Edges (Horizontal or Sloping) Rough Finished Surface of Concrete Flat, complete all as specified and as directed.

M&L Formwork to Edges of Concrete Flats, Treads, Breaks in Floors, Window Cills, Concrete Railings, Openings in Concrete Walls, Floor and Roofs not exc. 20 Cm Wide and Sides of RCC/PCC Bands in Walls, Horizontal or Sloping and Similar Work, exc. 10 Cm but not exc. 20 Cm Wide, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Pre-cast Cement Concrete Block Masonry with Solid Blocks of Size 300x200x200mm or 300x200x100mm, having Compressive Strength of not less than 100 Kg/ Sq Cm (as per IS-2185) in Cement Concrete 1:3:6 (20mm graded stone aggregate), exc. 10 Cm in Width and Setting in Cement Mortar 1:6, complete all as specified and as directed.

M&L Brick Work with Sub-Class ‘B’ Bricks (Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and as directed.

M&L Brick Work Half Brick thick with Sub-Class ‘B’ Bricks (Old Size Bricks), Straight or Curved on Plan to any Radius, built in Cement Mortar 1:4, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (12.5mm graded stone aggregate) 40mm thick in Damp Proof Courses to Horizontal or Vertical Surfaces including Use & Waste of Formwork and Applying evenly a coat of Blown type Bitumen @ 1.50 KG/SQM and blinding with Clean Dry Sand @ 0.05 CUM/SQM, complete all as specified and as directed.

M&L Cutting Holes in Brick/ Pre-cast Concrete Block Walling, not exc. Half Brick thick, built in Cement Mortar for inserting of Holdfasts, Lugs, etc. and Making Good to Dismantled portion with Cement Concrete 1:2:4 (20mm graded stone aggregate) or Cement Mortar 1:3 (as required) and Adjoining Surfaces in Cement Mortar 1:4, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) in Scantling, Cleansawn, Timber fixed (Unframed work), fixing with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) in Scantling but except Timber (Serviceable Timber Scantling obtained from BOQ Item No. 1.003 here-in-before), Timber fixed (Unframed work), fixing with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Plain, Solid, Straight, Chowkats and Frame, Wrought, Framed rebated on the Solid, Rounded or Chamfered, put together with Glue pinned at Joints, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Panelled Shutter 35mm thick (any number Panels) Plain, Framed with Lock Rails, having Panels of 12mm thick BWP, Commercial Ply or 12mm thick Veneered Particle Board Medium density, Wood Particle Board with Commercial Face Veneers and fitted to Chowkat, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Glazed and Skeleton Shutter 35mm thick, Open rebated and prepared to receive Glass, Gauze, etc., divided into Squares, with plain, chamfered or rounded, mitred and rebated Sash Bars (any numbers), fitted with cut and mitred beads for Glass, Gauze, etc., Sizes of Members of Shutters as specified in MES Schedule Part-I, Section 8, Clause No. 8.24(a) and fitted to Chowkats, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Glazed and Skeleton Shutter 30mm thick, Open rebated and prepared to receive Glass, Gauze, etc., divided into Squares, with plain, chamfered or rounded, mitred and rebated Sash Bars (any numbers), fitted with cut and mitred beads for Glass, Gauze, etc., Sizes of Members of Shutters as specified in MES Schedule Part-I, Section 8, Clause No. 8.24(b) and fitted to Chowkats, complete all as specified and as directed.

S&F Factory made Solid PVC Door Frame of Size 50x47mm made out of 5.0mm thick Plain Colour (Ivory Shade) PVC Sheet reinforced with Mild Steel Square Tube and fixing in opening as per Specification and Drawing of MES Schedule Part-II, complete all as specified and as directed.

M&L Factory Made Solid Panel PVC Door Shutter 30mm thick (Style) Plain colour (Ivory shade) consisting of Frame made out of Mild Steel Tubes for Top and Bottom Rails, Mild Steel Frame shall be covered with heat moulded wood grain PVC ‘C’ Channel having a PVC Sheet Strip of 20mm width stuck inside with Solvent Cement for Stiles and wood grain PVC Sheets for Top Rail, Lock Rail & Bottom Rail on either side and as gap insert for Top Rail & Bottom Rail, Panelling of wood grain PVC Sheet to be fitted in the Mild Steel Frame welded/sealed to the Stiles and Rails with suitable 5mm thick x 15mm wide PVC Sheet beading used inside Stiles and Rails and decorative PVC Beading of 10mmx10mm (90) and jointed together with Solvent Cement and fixing in the Frame at Site, complete all as specified and as directed.

M&L Anodised Aluminium Powder Coated (Thickness of Powder Coating not less than 50 micron) Frame for Doors, Windows, Ventilators with One or More Rebates including Joining Cleat for fixing, etc., complete all as specified and as directed.

M&L Anodised Aluminium Powder Coated (Thickness of Powder Coating not less than 50 micron) Door Shutters, Aluminium Section weighing not less than 0.55 KG/RM including necessary Joining Cleats, Glazing Clips, Rubber/ Neoprene Packing, Handles (as approved) - 2 No. in Each Door, Stainless Steel Hinges of Size as ordered, anodised Aluminium Snap Beading, Screws, etc, complete all as specified and as directed. NOTE : Cost of Aluminium Fittings/ Builders Hardware as metioned here-in-above will deem to include in the Quoted Unit Rate.

M&L Anodised Aluminium Window and Ventilator Shutters, Side Hung type without Sash Bars, Aluminium Sections weighing 0.55 KG/RM including necessary Joining Cleats, Glazing Clips, Rubber Packing, Anodised Aluminium Snap Beading, Screws, Anodised Aluminium Fittings such as Peg Stays 150mm long (1 No.). Hinges Type B-21, 100mm long (2 No.) suitable Handle (1 No.), complete all as specified and as directed. NOTE : Cost of Aluminium Fittings/ Builders Hardware as metioned here-in-above will deem to include in the Quoted Unit Rate.

S&F Aluminium anodised Barrel Tower Bolt of Size 150mm long, Extruded Section, complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt of Size 200mm long, Extruded Section, complete all as specified and as directed.

S&F Aluminium alloy, anodised, Sliding Door Bolt 250mm long with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy and fixed, complete all as specified and as directed.

S&F Aluminium alloy, anodised, Sliding Door Bolt 300mm long with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy and fixed, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge of Size 75mm, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge of Size 100mm, complete all as specified and as directed.

S&F Aluminium Handle of Size 125mm, anodised, Cast type, complete all as specified and as directed.

S&F Aluminium Handle of Size 150mm, anodised, Cast type, complete all as specified and as directed.

S&F Floor Door Stopper with Overall length of Cover Plate 140mm of Aluminium Alloy Body and Tongue (as approved) anodised, with Hard Drawn Steel Spring, fixed in Floor, complete all as specified and as directed.

S&F Mild Steel 300mm, Ordinary Rat Tail Rod pattern Springs including Roller and Roller Plate and Fixed-in-repairs, complete all as specified and as directed.

M&L Stainless Steel Curtain/ Drapory Rod having 24mm Outer dia with Wall thickness 1.00mm (minimum) including Brackets, Side Holders and Rings, etc. and Fixed-in-repairs, complete all as specified and as directed.

S&F Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples, complete all as specified and as directed.

S&F Sheet Glass 3.0mm thick, Plain, Ordinary quality and Glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

S&F Figured Glass, Pin Head type, 3.0mm thick and Glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

S&F Sheet Glass 5.0mm thick, Plain, Ordinary quality and Glazing with Oil Putty in Square, not exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

M&L TMT Bars 10mm dia and Over, cut to length, bent to shape required including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 8mm dia in Stirrups, Spacers and Binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L Mild Steel Bands, Straps, Supports or Stays for Rainwater, Ventilating Pipes including Bolts, Hooks (Stay) for large Gates; Hook and Pintle Hinges: large Hasps and Staples; Hand Made Sliding Bolts; Clamps; Holdfasts; Wall Ties and similar small Articles conforming to Fe-290 Gde-E-165, complete all as specified and as as directed.

M&L Rolled Mild Steel Sections in Joist, Channel, Angle, or Tee Sections in Vertical Post, fixed independently, without Connecting Plates, etc. (cut to ordinary Lengths i.e. within 20mm of the Length indicated), conforming to Fe-410-W (Gde E-250) Quality 'B', complete all as specified and as directed.

M&L Rolled Mild Steel Sections in Roof Trusses (Framed), Trussed, Purlins, Crane Gantries, Rails and Fastenings and Heavy Bracket Framing (Beam, Tee, Angle, Channel or Flat Sections) including Distance Pieces, Cleats, etc., conform to Fe-410-W (Gde E-250) Quality 'A', complete all as specified and as directed.

M&L Rolled Mild Steel Sections in Main and Cross Beams, Hip & Jack Rafters, Purlins where connected to Common Rafters, Running Rails and Guides for Sliding Doors, conforming to Fe-410-W (Gde E-250), Quality 'A', fixed with Angle Cleats or Other Connecting Plates, complete all as specified and as directed.

M&L Plates (Plain or Chequered) Channels, Square cut or Notched (Ordinary and Counter Sunk) forming Holes, without any Aattachment, conforming to Gde Fe-410-W (Gde E-250) Quality 'B', complete all as specified and as directed.

M&L Mild Steel Screw Bolts (Machine made) of any description (Dia of Neck and Length of Bolt as ordered/ as per Site requirment), with Hexagonal or Square Heads at One End and screwed the Other End, or screwed Both Ends, Each screwed End to be fitted with Washers and One Hexagonal or Square Nut, complete all as specified and as directed.

M&L Mild Steel Rag or Lewis Bolts, Length of Bolt exc. 15 Cm but not exc. 30 Cm and Diameter of Neck 12mm, screwed One End, with Hexagonal or Square Nuts and Washers, the Other End Enlarged and Jagged or Lewised, complete all as specified and as directed.

S&F Corrugated Mild Steel Sheeting 0.63mm thick, Galvanised @120 Gram Per Sqm, with Two Corrugation Side Lap, fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

M&L Re-fixing Corrugated Mild Steel Sheeting 0.63mm thick (Serviceable Sheeting obtained from Item No. 1.007 here-in-before) with Two Corrugation Side Lap, fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Corrugated Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Plain Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Ridges/ Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

M&L Exposed Suspended False Ceiling System with GI Powder Coated Snap Grid/ Frame Work of Size 605x605mm, all as per Specification and Drawing of MES Schedule (except Hangers), complete all as specified and as directed.

S&F Hangers 4.0mm dia GI (upto 1200mm length) for adjusting Level, fixed to Roof Slabs by means of Ceilling Cleats made out of GI Flat 40x3.0mm in Size, 60mm long and Expansion Hold Fasteners 12.5mm dia, 40mm long, complete all as specified and as directed.

S&F HSPC Non-Asbestos Fibre Cement Building Boards 4.0mm thick, Pre-primed, Self Embossed, Textured Designer Boards, Water Resistant, Termite Resistant, Fire Resistant for insulation, fixed or laid/ inserted to GI/ Aluminum Snap Grid Frame Work with Screws, complete all as specified and as directed.

S&F Prelaminated Particle Boards 12mm thick, Interior grade, Prelaminated both Sides with Decorative Choice Laminations, fixed with Screws to Timber Frame Work, complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) 75mm thick in Sub-base to Floors, etc., complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) 40mm thick in Flooring, etc., laid in Alternate Panels, finished Concrete Surfaces Even and Smooth with using Extra Cement, complete all as specified and as directed.

M&L Glass Dividing Strips 38mm Wide and 3.0mm thick and inserted in Position, conform to Design, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (12.5mm graded stone aggregate) 25mm thick as Base Course for laying Tiles on Flooring, etc., finished Concrete Surfaces Fair and Even, complete all as specified and as directed.

M&L Non-skid Ceramic Coloured Tiles (1st quality and as approved) 7.0mm to 8.0mm thick (Square/ Rectangular), Area of Each Tile exc. 0.11 Sqm but not exc. 0.18 Sqm in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Cement Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Non-skid Ceramic Coloured Tiles, Joint Free (1st quality and as approved) 7.0mm to 8.0mm thick (Square/ Rectangular), Area of Each Tile exc. 0.11 Sqm but not exc. 0.18 Sqm in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Cement Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Non-skid Ceramic Coloured Tiles, Joint Free (1st quality and as approved) 7.0mm to 8.0mm thick (Square/ Rectangular), Area of Each Tile exc. 0.11 Sqm but not exc. 0.18 Sqm in Vertical Surfaces i.e. Dado, Skirting, etc., Set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Cement Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Non-skid Ceramic Coloured Tiles, Joint Free (1st quality and as approved) 7.0mm to 8.0mm thick (Square/ Rectangular), Area of Each Tile exc. 0.18 Sqm but not exc. 0.38 Sqm in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Cement Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Non-skid Ceramic Coloured Tiles, Joint Free (1st quality and as approved) 7.0mm to 8.0mm thick (Square/ Rectangular), Area of Each Tile exc. 0.18 Sqm but not exc. 0.38 Sqm in Vertical Surfaces i.e. Dado, Skirting, etc., Set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Cement Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Glazed Ceramic Coloured Tiles 350x250x7.0mm or 450x350x7.0mm thick (1st quality and as approved) in Vertical Surfaces i.e. Dado, Skirting, etc., Set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Cement Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) 75mm thick in Plinth Protection, etc., Laid in Alternate Panels, finished Concrete Surfaces Even and Smoooth without using Extra Cement, complete all as specified and as directed.

M&L Joint Filling on Plinth Protection with 1 Part of Bitumen and 3 Parts of Sand, complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) 100mm thick in Sub-base to Floors, Paver Blocks, etc., complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) 100mm thick in Flooring, etc., laid in Alternate Panels, finished Concrete Surfaces Fair and Even, complete all as specified and as directed.

M&L Machine Pressed Pre-cast Concrete Interlocking Paver Block 60mm thick, M-35 Grade of any Shape and Size (as ordered) with Grey Cement and Pigment, conforming IS-15658-2006, ISI Marked, laid Dry over Sand Cushioning, complete all as specified and as directed. NOTE : Sand Cushioning will be Measured and Paid for separately under appropriate Item.

M&L Sand Cushioning with Clean and Dry Sand, Filling under Paver Blocks in layer not exc. 50mm thick including Watering and Consolidation, complete all as specified and as directed.

M&L Rendering 10mm thick in Cement Mortar 1:6 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering 15mm thick on Bricks/Pre-cast Blocks or Concrete Works consisting in 2 layers, Backing/Under layer of 10mm thick in Cement Mortar 1:4 and Float/Top layer 5.0mm thick in Cement Mortar 1:4 including mixing WPC to Float/Top layer, finished Fair and Even, complete all as specified and as directed. NOTE : Water Proofing Compound (WPC) will be Measured and Paid separately under appropriate Item,

Supply only Water Proofing Compound (as approved), conforming to IS:2645-2003, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and applying Three Coats of White Wash, complete all as specified and as directed.

M&L Preparing Old Decorated/Treated Plastered Surfaces of Walls and applying One Coat of White Wash, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and applying Wall Care Putty 3.0mm thick in Two Coats (1.5mm thick in Each Coat) on Plastered Surfaces of Walls including Cutting and Rubbing down to obtain an Even and Smooth Surface, complete all as specified and as directed.

M&L Applying Two Coats of Distemper Oil Emulsion (as approved) over a Coat of Chalk Whitening (Priming Coat) on Putty Finished Surfaces, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and applying Two Coats of Distemper Oil Emulsion (of approved Tint) over a Coat of Chalk Whitening (Priming Coat), complete all as specified and as directed.

M&L Preparing Old Distempered and Painted Surfaces of Walls by Washing, Rubbing down and Stopping of Surfaces and applying Two Coats of Distemper Oil Emulsion (of approved Tint), complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Two Coats of Cement Based Paint (of approved Tint) over a coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Preparing Old Decorated/Treated Plastered Surfaces of Walls and applying One Coat of Cement Base Paint (of approved Tint), complete all as specified and as directed.

M&L Preparing New Wooden Surfaces of any description, exc. 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Old Painted Wooden Surfaces of any description, exc. 10 Cm in Width or Girth and applying One Coat of Synthetic Enamel Paint (1st quality Paint of approved Tint), complete all as specified and as directed.

M&L Preparing Steel and Iron Surfaces of any descriptions, exc. 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L Preparing Old Treated Steel and Iron Surfaces of any descriptions, exc. 10 Cm in Width or Girth and Applying One Coat of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint), complete all as specified and as directed.

M&L Preparing New or Previously Treated Surface of Wood and Wood based Materials of any description and girth and treated with Two Coats of Creosote Oil, complete all as specified and as directed.

M&L Preparing previously Untreated Surfaces of Wood and Wood Based Materials, of any description and girth not otherwise described and treating with Tar or Coal Tar Black Paint to Backs of Chowkats, etc. Area tarred exc. 0.10 Sqm but not exc. 0.50 Sqm Each including Sanding with Clean Sharp Sand after tarred, complete all as specified and as directed.

M&L Preparing previously Untreated Surfaces of any description and girth not otherwise described and treating with Tar or Coal Tar Black Paint to Holdfast or similar Small Items, Area tarred not exc. 0.10 Sqm Each including Sanding with Clean Sharp Sand after tarred, complete all as specified and as directed.

S&F Galvanised Steel Tubing 15mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

S&F Galvanised Steel Tubing 20mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

S&F Bib Tap 15mm bore (dia) Cast Copper alloy, Chromium Plated, Fancy type, with Crutch or Butter-fly Handle, screwed down, screwed for Iron Pipe or for Brass Ferrule, complete all as specified and as directed.

S&F Pillar Tap 15mm bore (dia), Cast Copper alloy, Chromium Plated, with Capstan Heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with Long Screwed Shanks and Fly-nuts, screwed for Iron Pipe, complete all as specified and as directed.

S&F Stop Valve 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type, screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions, complete all as specified and as directed.

S&F Stop Valve 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type, with Long Shank and Cup (Concealed type) screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions, complete all as specified and as directed.

S&F Gun Metal Globe/Gate Valve 20mm bore (dia) with Iron Wheel Head, screwed both Ends for Iron Pipe, complete all as specified and as directed.

M&L Rotational Moulded Polyethene Water Storage Tank 1000 Litre Capacity, Cylindrical, Vertical with Closed Top, 3 layered, conforming to IS:12701-1996, hoisted and fixed in Position all as specified in MES Schedule and providing Water Pipe Line Connections, complete all as specified and as directed.

S&F PTMT Ball Valve 20mm bore (dia), having weight not less than 210 Gram, high pressure with Epoxy Coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe, complete all as specified and as directed.

S&F Vitreous China White Wash Down Water Closet Pan (Pedestal Pattern) with PVC (SWR) ‘P’ or ‘S’ Trap and Fixing Bolts and Making Good to Distrubed/ Floor Surfaces in Cement Mortar 1:3, complete all as specified and as directed.

S&F White Plastic Water Closet Seat and Cover for Water Closet Pan (Pedestal Pattern), Closed Pattern with Flat bottom and Cover and Mild Steel Chromium plated or Aluminised Hinging Device, complete all as specified and as directed.

S&F Health Faucet 2-in-1 Brass Chromium Plated with 1.20 Metre Stainless Steel Hose/ Tube & Hook suitable for Hanging on Walls, complete all as specified and as directed.

S&F PVC Flushing Cistern 10 Litre capacity White, Low Level, Valveless, Syphonic Action type with Inlet, Ball Valve, Float & Handle, and PVC Flush Pipe 32mm bore (dia) of suitable Length, a Pair of Cast Iron Brackets/ Erecting Stand duly painted including cutting and pinning in Ends, Making Good disturbed Surfaces in Cement Mortar 1:3, complete all as specified and as directed.

S&F Vitreous China White Wash Hand Basin 600x480mm in Size, Flat Back with Brass Chromium Plated Waste Fitting 32mm bore (dia) and PVC Waste Pipe 32mm bore (dia) of suitable Length, a Pair of Cast Iron Brackets/ Erecting Stand duly Painted, Cutting and Pinning in Ends and Making Good Disturbed Surfaces in Cement Mortar 1:3, complete all as specified and as directed.

S&F PVC Connection Pipe 15mm in Size and 450mm in length with PTMT Nuts suitable for connecting with Flushing Cistern, Wash Hand Basin, etc., complete all as specified and as directed.

S&F Brass Chromium plated Shower Rose 125mm in Size with Arm and Flanges, with or without Swivel Joints including fixing to GI/ Steel Pipe 15mm bore (dia) or Union, complete all as specified and as directed.

S&F Soap Dish not less than 150mm in Size, Chromium plated, Fancy type (as approved), fixed on Wall with Wooden/ PVC Cleats and Brass Chromoum Plated Screws, complete all as specified and as directed.

S&F Corner Glass Shelf with ABS Brackets (as approved), fixed to Walls with Brass Chromoum Plated Screws on Wooden/ PVC Cleats, complete all as specified and as directed.

S&F Tubular Towel Rail 20mm dia, Brass Chromium Plated, D-type, 60 Cm long between Flanges with Bracket (One Pair), fixed to Wall with Brass Chromoum Plated Screws on Wooden/ PVC Cleats, complete all as specified and as directed.

S&F PVC (SWR) 75mm bore (dia) Floor Trap having Diameter of Outlet 75mm, Plain with Grating including Jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) 75mm bore (dia) Pipe, Single Socketed, in any length with Rubber Ring Joints, laid in Trenches or in Floors, complete all as specified and as directed.

S&F PVC (SWR) Bend 75mm bore (dia), any Radius, etc. and Jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) 110mm bore (dia) Pipe, Single Socketed, in any length with Rubber Ring Joints, laid in Trenches or in Floors, complete all as specified and as directed.

S&F PVC (SWR) Bend 110mm bore (dia), any Radius, etc. and Jointing with Solvent Cement, complete all as specified and as directed.

E/M SERVICES/WORKS

M&L Taking down carefully Copper Point Wiring (Light, Fan, Socket or Power) complete from in any Position including Fixture and Fittings such as Switches, Ceiling Roses, Pendants, Regulators, Sockets but excluding Light Fittings of any description, Making Good Disturbed Surfaces of Walls/ Ceillings, etc. in Cement Mortar 1:3 including providing Surface Treatment (White/Colour Washing, Distempering, Painting, etc.) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core FRLSH Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated, unsheathed, multi-stranded single core FRLSH Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable Size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable Size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE LIGHT/ FAN/ BELL POINT controlled by One 1-way Switch 6 Amp, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire for ONE 3/5 PIN SOCKET 6 AMP POINT on SAME BOARD, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core FRLSH Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core FRLSH Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable Size (approx 25/32mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable Size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Point Wiring with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core FRLSH Copper Conductor Cable with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core FRLSH Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable Size (approx 25/32mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable Size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6/16 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Point Wiring with 4.0 Sqmm (nominal area) 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core FRLSH Copper Conductor Cable with 4.0 Sqmm (nominal area) 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core FRLSH Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable Size (approx 25/32mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable Size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6/16 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

S&F Switch Piano 6 Amp, Single Pole, Flush type, 1-way, 230 Volt AC and connecting up, complete all as specified and as directed. NOTE : Unserviceable Switch Piano 38 No. derived from Taking down of Point Wiring will be catered under Schedule of Credit.

S&F Socket Outlet 6 Amp, 5 Pin, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed. NOTE : Unserviceable Socket Outlet 11 No. derived from Taking down of Point Wiring will be catered under Schedule of Credit.

S&F Switch Socket Combination 6 Amp, 3 Pin, 2-in-1, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed. NOTE : Unserviceable Switch Socket Combination 11 No. derived from Taking down of Point Wiring will be catered under Schedule of Credit.

S&F Switch Socket Combination 6/16 Amp, 3 Pin, 2-in-1, Multi-plug, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed. NOTE : Unserviceable Switch Socket Combination 10 No. derived from Taking down of Point Wiring will be catered under Schedule of Credit.

S&F Lamp/ Angle Holder PVC/ Polycarbonate type with Back Plate suitable for Batten Fitting and connecting up, complete all as specified and as directed.

S&F Ceiling Rose 65x50mm, 3 Terminals, Surface Bakelite suitable for 230 Volt AC and connecting up, complete all as specified and as directed. NOTE : Unserviceable Ceiling Rose 19 No. derived from Taking down of Point Wiring will be catered under Schedule of Credit.

S&F Ceiling Fan Regulator, Electronic, Stepped type, 230 Volt AC including necessary Connection and connecting up, complete all as specified and as directed.

S&F Ceiling Fan Regulator, Dimmar Switch type, 230 Volt AC, Rotary Stepped, Electronic type 120/280 Volt and connecting up, complete all as specified and as directed. NOTE : Unserviceable Fan Regulator 05 No. derived from Taking down of Point Wiring will be catered under Schedule of Credit.

S&F LED Bulk Head Light Fitting 1x10 Watt having Plastic Housing with Clear Prismatic Diffuser LED 10 Watt Lamp and connecting up with and including suitable Size and Length Twisted Flexible Copper Conductor Cable, complete all as specified and as directed.

S&F LED Integrated Batten T-5 Tube Light Fitting 1x20 Watt having 4 Feet long including LED Tube 20 Watt, connecting up with and including suitable Size and Length Twisted Flexible Copper Conductor Cable, complete all as specified and as directed. NOTE : Unserviceable Light Fitting 14 No. against Taking down of Point Wiring will be catered under Schedule of Credit.

S&F LED PANEL (2'x2') Light Fitting 30 Watt with High Brightness SMD LEDs as Light Source, Recess/Ceiling mounted, Ultra Modern, Enviromentaly Friendly, New Generation with Electronic Driver 30 Watt and all Accessories, Pre-wired and connecting up with including suitable Size and Length Twisted Flexible Copper Conductor Cable, 3 Core including Taking down/ out Unserviceable Light Fitting, complete all as specified and as directed. NOTE : Unserviceable Light Fitting 08 No. against Taking down of Point Wiring will be catered under Schedule of Credit.

M&L Taking down Ceiling Fan, Exhaust Fan of any Make and Sweep from any Height after disconnecting Electric Connection and Keep in Safe Custody for Re-fixing / Re-hanging, complete all as specified and as directed.

M&L Re-hanging/Refixing only Ceiling Fan, Exhaust Fan (obtained from BOQ Item No. 2.018 here-in-before) and connecting with and including suitable Size Twisted Flexible Copper Conductor Cable from Ceiling Rose to Connector of the Fan, complete all as specified and as directed.

M&L Mild Steel Flat Iron 40x5mm in Fan Hooks, Cut to Length, bent to Shape as ordered, drilling holes for Bolts including providing Mild Steel Bolts, Nuts and Washers, conforming to Fe-290 Gde-E-165, complete all as specified and as as directed.

Supply & Hanging BLDC Ceiling Fan 1200mm Sweep, 26 Watt with Squirrel Cage Induction Motor, having 3 Blades, Holding Down Rod and Accessories, 230 Volt, providing Electric Connection from Ceiling Rose to Ceiling Fan with and including Twisted Flexible Copper Conductor Cable of suitable Size and Length, 3 Core, complete all as specified and as directed.

S&F Exhaust Fan 300mm Sweep with Louver Shutter, Single Phase, 230/240 Volt AC with Fixing Arrangement using Fastener and and providing Electric Connection with and including suitable Size Copper Conductor Cable from Ceiling Rose to Exhaust Fan, complete all as specified and as directed.

S&F MCB Single Pole 6 Amp to 32 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up, complete all as specified and as directed. NOTE : Unserviceable MCB 12 No. obtained from Taking down/ out will be catered under Schedule of Credit.

S&F MCB Single Pole & Neutral 40 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up, complete all as specified and as directed. NOTE : Unserviceable MCB 02 No. obtained from Taking down/ out will be catered under Schedule of Credit.

S&F MCB Triple Pole & Neutral 63 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up, complete all as specified and as directed.

S&F Sheet Metal Enclosure for DB's when MCBs to be used 4-Way, SPN, 240 Volt, Double Doors, Epoxy Based Powder Coated Painted, suitable for mounting MCB DP/SPN as Incomer and MCB SP as Out-going with 200 Amp rated Bus-bar, Neutral Bar, Earth Bar, Connecting Cable Links and Connecting up, complete all as specified and as directed.

S&F Sheet Metal Enclosure for DB's when MCBs to be used 8-Way, SPN, 240 Volt, Single Door, Epoxy Based Powder Coated Painted, suitable for mounting MCB DP/SPN as Incomer and MCB SP as Out-going with 200 Amp rated Bus-bar, Neutral Bar, Earth Bar, Connecting Cable Links and Connecting up including Taking down/out Unserviceable Sheet Metal Enclosure for DBs, complete all as specified and as directed. NOTE : Unserviceable Sheet Metal Enclosure for DBs 02 No. obtained against Taking down/ out will be catered under Schedule of Credit.

S&F Sheet Metal Enclosure for DB's when MCBs to be used 8-Way, SPN, 240 Volt, Double Doors, Epoxy Based Powder Coated Painted, suitable for mounting MCB DP/SPN as Incomer and MCB SP as Out-going with 200 Amp rated Bus-bar, Neutral Bar, Earth Bar, Connecting Cable Links and Connecting up, complete all as specified and as directed.

Supply and Laying or Fixing or Passing through Pipe, 1100 Volt grade Heavy duty Cable with PVC insulated Aluminium Stranded Conductor served with an Inner sheathing of PVC Tape armoured with Galvanised Steel Wire or Tape and Overall PVC sheathed, Nominal Cross section 4.0 Sqmm, 4 Core in Service Connection including Taking down/out Unserviceable Service Connection Cable (160.00 RM) of any description from any Situation, complete all as specified and as directed.

Supply, Installation & Commissioning LT Feeder Pillar Box, Factory Made (CPRI Approved/ Tested Manufacturer), made out of 3.15mm thick CRCA Sheet, suitable for 415 Volt, 3 Phase, 4-Wire System, 50 Hz Supply, Outdoor type, Platform mounted of Size 600x500x450mm, Dust Proof and Vermin Proof (IP54), Epoxy Powder coated, Front & Rear Opening, Double Door Shutters with Locking Arrange- ments, Feeder Pillar Box having Epoxy Powder coated, mounted on Mild Steel Angle Iron Frame 50x50x6.0mm and not less than 600mm Height from Natural Ground Level, grouting Angle Iron Legs in Cement Concrete 1:2:4 (20mm graded stone aggregate) Block of Size 300x300x600mm including necessary Formwork, Earth-work, expossed Angle Iron Frame shall painted with Two Coats of Synethetic Enamel Paint over a Coat of Red Oxide Zinc Chrome Primer, Providing all Electric Connections and Testing, Comprising with and including following Accessories including Taking down/out unserviceable Feeder Pillar Box of any description, complete all as specified and as directed :- (a) Copper Bus-bar 200 Amp, 4 Strip, installed on Porcelain/ Epoxy - 01 Set Insulators (b) MCCB 125 Amp, 4 Pole, 25 kA, 415 Volt - 01 No. (c) MCCB 63 Amp, 3 Pole, 25 kA, 415 Volt - 03 No. (d) Digital Amp Meter 0-200 Amp Square Flush Pattern - 01 No. (e) Digital Voltmeter 0-500 Volt, Square Flush Pattern - 01 No. (f) LED Indicator Lamp (RYB) in Incomming Phase - 01 Set (g) MCCB shall be provided with suitable Spreaders of Copper Conductor for fixing of Incoming Cables (h) Connection from MCCB to Bus-bars with Solid Copper Conductor

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0mm thick, buried directly in Ground vertically to a depth not less than 2.25 Metre below Ground Level with Top Edge of Earth Plate at depth not less than 1.50 Metre below normal Ground Level, connected to Galvanised Earth Lead Wire 4.0mm dia by means of Bolts, Nuts, Check, Nuts and Washers of Galvanised Iron or Steel and Earth Wire protected with and including GI Pipe 15mm bore (dia) light grade, connected to Test Point upto 7.50 Metre away from Earth Electrode situated, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc.150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of Size 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/ Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing including Taking down/ out unserviceable Earthing (02 Set) of any description, complete all as specified and as directed.

M/s JK Jangid and Company

M/S CHANDAN ENTERPRISE

Construction House

AFTAB ENTERPRISES

MAZUMDAR ENTERPRISE

FREEZCON

SHRI MANOJ KONWAR

Kaushik Enterprises

M/s. R. K. Trading Company

M/s Sashi Enterprise

M/S Abhi Traders

Prova Stores

M/S R & R D ENTERPRISES