Construction of Combined Building Govt Senior Secondary School and Primary School at Gulling Distt Lahaul and Spiti HP

Amount

Excavation in foundation and trenches in earth work in all heights and depths in all kinds of soils, including saturated soils comprising of pick work, jumper work and blasting work both in soft and hard rock, with chiseling and wedging out of rock;(where blasting is prohibited) and their intermediate classification of soils including ,dewatering including pumping or bailing out of water wherever required, setting out to required lines, levels as shown on the drawing and as directed by the Engineer-in- Charge at site, according to the H.P.PWD.specification of 1990 (One thousand Nine hundred Ninety) Volume-I and sorting out useful & unuseful materials and stacking the same in all leads and lifts and transportation of the unuseful materials on approved dumping sites through all modes of transportation including head load, animal load or mechanical means along with its leveling fine dressing and all labour, machineries, materials, tools equipments and safety measures and iincidentials necessary to complete the work by mechanized means and labour (if any required) .All usefull materials, such as stones, shingles, aggregate and slates shall be sorted to the maximum possible extent complete as per H.P.PWD.specification of 1990 (One thousand Nine hundred Ninety) Volume-I i/c carriage of material, labour , tool and plant thyough all modes of transportation with in all leads and lifts and as perdirection of Engineer-In-Charge.

Excavation in earth work in drains and channels in all heights and depths in all kinds of soils, including saturated soils comprising of pick work, jumper work and blasting work both in soft & hard rock and wedging out of rock;(where blasting is prohibited)and their intermediate classification of soils including ,dewatering wherever required, setting out to required lines, grades, side slopes, trimming bottoms and levels as shown on the drawing and as directed by the Engineer-in-Charge at site, as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Filling in plinth with sand under floor including watering, ramming, consolidating and dressing complete within all leads, lifts of materials and other incidentals as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing form work with steel plates 3.15 (Three point One Five ) millimeters thick welded with angle iron in frame 30*30*5 (Thirty into Thirty into Five ) millimeters, so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies in all heights of propping and centering below supporting floor to ceiling and removal of the same in-situ-reinforced concrete and plain concrete work as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Foundation footings basis of columns etc. and mass concrete.

Flat surfaces such as soffits of suspended floors roofs landings and the like floors etc. up to 200 mm (two hundred millimeter) in thickness.

Columns pillars, posts and struts square rectangular or polygonal in plan.

Beams, cantilever, girders and lintels:-sides and soffits of beams, beam haunchings cantilever, girders bressumers and lintels not exceeding 1 (one)meter in depth.

Stair cases with sloping or stepped soffits excluding landings.

Edges of slabs and breaks in floors and walls:-under 20 cm(twenty centimeter) wide.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (One cement : Four coarse sand: Eight graded stone aggregate 40 mm( Forty Millimetre) nominal size as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and laying cement water proofing treatment with Dr. FXIT-FAST FLEX or equivalent with two component polymer modified cementitious coating consisting of comentitious powder and a polimer liquid in to coats for Ist coat:- clean and satuta surface and then applying a coat of Dr. FIXIT and the same process shall be extended upto 300mm(three hundred milimeter vertically the second coat shall be applied in opposit direction after four to six hours of application of firsty coat than sprinkle sand on top surface of applied Dr. FRIXIT then apply cement mortar 1:4(one cement:four sand) and admixed with 200 ml(two hundred milileter) of pidiproof LW @ 200 ml (two hundred milileter) peer 50kg(fifty kilogramme) bag as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and laying Damp Proof Course 38 mm (thirty eight millimeter) thick cement concrete 1:2:4{one cement isto two sand isto four graded crushed hard stone aggregate 12.5 mm(tweleve point five millimeter) nominal size}and curing complete as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and laying cement concrete 1:1½:3 [ One cement isto One and half sand isto Three graded crushed hard stone aggregate 20 (Twenty) millimeters nominal size]mechanically mixed and vibrated and curing complete, excluding cost of form work and reinforcement for reinforced concrete work as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Foundation footing bases of columns and the like and mass concrete.

Suspended floors, roofs landings shelves and their support balconies, beam, girders bressumers and cantilevers in all floors up to all heights and levels.

Columns, pillars, posts and struts in all floors up to all heights and levels.

Stair cases (except spiral stair cases)excluding landing but including preparing of surface and finishing of nosing in all floors above plinth level to floor two level.

Providing and laying upto all floor level reinforced cement concrete 1:1½:3 [ One cement isto One and half sand isto Three graded crushed hard stone aggregate 20 (Twenty) millimeters nominal size]mechanically mixed and vibrated to give a smooth and even surface including centring and shuttering etc. but excluding cost of reinforcement in :- Mouldings as in cornices windows sills etc. not exceeding 15cm(fifteen centimeter) in girth as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:2:4 (one cement : two coarse sand : four graded stone) aggregate 20 mm(twenty millimeter) nominal size) complete upto floor all level as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and laying Cement concrete grade 1:3:6(one cement : Three coarse sand : Six graded stone aggregate) 40mm ( forty millimetre) nominal size. in position cement concrete of specified grade including the cost of centering and shuttering upto plinth level as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Steel reinforcement (TATA /SAIL / JINDAL PANTHER/RINL) for R.C.C. (Reinforcement cement concrete) work including straightening, cutting, bending, placing in position and binding complete including cost of binding wire Complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500 ( Five hundred ) D or more steel bars as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Random Rubble Masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (One cement :Six coarse sand : Twelve graded stone aggregate 20 mm( Twenty millimetre nominal size) upto plinth level with Cement mortar 1:6 (One cement : Six coarse sand) as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Brick work in Rat Trap Bond with common burnt clay F.P.S. (non modular) bricks of class designation 7.5( Seven point Five) in superstructure above plinth level up to floor all level in all shapes and sizes in : Cement mortar 1:4 (One cement : Four coarse sand) as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and filling Mud mortar in cavity in between walls as per HP.PWD drawing & specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and laying 11.5 cm ( eleven point five thick) thick machine preessed mud bricks manufactured in a standarded ratio adding 5% ( five percent) cement abd straw to add extra strength and to increase the load bearing capacity in mud mortar. in partation etc as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 ( Seven point Five) in superstructure above plinth level up to floor all level in all shapes and sizes in : Cement mortar 1:4 (One cement : Four coarse sand) as per HP.PWD specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One), including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5( Seven point Five) in superstructure above plinth level up to floor all level. Cement mortar 1:3 (One cement :Thre coarse sand) as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Boulder filling tightly dry hand packed under floor including watering, ramming, consolidating etc . Complete as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing 1st Class Deodar Wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately) as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing Sal Wood work in frames of false ceiling, partitions etc. sawn and fixed in position with necessary stainless steel screws etc as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing factory made flush door 35mm(thirty five milimeter) thick (commercial both sides) i.e. non decorative phenol bonded termite resistant and water proof core of block board construction with full frame of hard wood and well matched commercial three ply veener with vertical grain of cross bans and face veener on both faces of flush door shutter IS No.2202 ( Two Two Zero Two) of century plyboard (i) ltd or its equivalent including black enameled M.S. iron butt hinges, with necessary screws:-35mm (thirty five milimeter) thick as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing 5 cm ( Five centimeter)Thick Second class teak wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing 35 mm ( Thirty Five ) thick first class deodar wood with double glass shutter with rubber gasket to avoid air pressure as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing 25 to 40 mm ( twenty five to Forty milimeter ) thick panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured) 12 mm Twelve milimeter ) thick three layered Teak) veneered faced Partical Board ( Exterior) as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing 8 mm ( Eight Milimeter ) thick Cement Bonded Particle board in Duct door as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing 8 mm ( Eight Milimeter ) thick ply board in Cub board cabinets/shalves as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing 6 mm ( Six Milimeter ) thick hard wood edging in Cub board and SDB as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing 19 (Nineteen) millimeters thick commercial board water proof shutters for cup board with 6mm hard wood edging on exposed surface, including fixing with nickel plated piano hinges with screws complete as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing & fixing wire gauge shutters using galvnized M.S. wire gauge of I.S. gauge designation 85(Eighty five) G with wire of dia 0.56 mm(Zero point fifty six millimeter) 40mm (forty millimeter) thick in Second class deodar wood for doors windows and clrestory windows including bright finished black enameled iron hinges with necessary screws as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing Aluminium Sliding Door Bolts, ISI marked anodised (anodic coating not less than grade AC 10 (ten) as per IS : 1868 One Eight six eight), transparent or dyed to required colour or shade, with nuts and screws etc. complete as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

300 x 16 mm (three hundred into sixteen millimeter).

250 x 16 mm (two hundred fifty into sixteen millimeter).

Providing and fixing Aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

250 x 10 mm (Two hundred fifty into ten milimeter.

200 x 10 mm (two hundred into ten millimeter)

Providing and fixing Aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 (ten) as per IS : 1868 One Eight six eight), transparent or dyed to required colour or shade, with necessary screws etc. complete as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

125 mm (one hundred twenty five millimeter)

100 mm (one hundred millimeter)

Providing and fixing Chromium plated 90mm (ninety milimeter) MS hasps and stapples (Safety type) with necessary screws including all leads, lifts and carriage of materials as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing 12mm(twelve milimeter)thick Green Chalk Board (non-Magnetic) with superior quality framing specially anodised aluminium profile 20x15mm(twenty into fifteen milimeter) with corners of black surface shall be non-porous ceremic particles on the top green surface for smooth writing with chalk over 1mm(eleven milimeter) thick particle board which shall have backing material of galvanised sheet 0.28mm(zero point twenty eight milimeter) thick approx. The board shall be fixed on the wall with specially desinged "J" clumps and square clumps with the help of nylon sleves and screws as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing 1.00mm(one point Zero zero milimeter) thick coloured or plain laminated sheet(URO Mica or Its equivalent) on boards/ ply wood sheets with approved adhesive and nails complete including all leads, lifts and carriage of materials as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing PGI Sheet 0.63 ( zero point sixty three) mm thick lining with on one face inner face with butt jointing and nails (frame work and cover fillets to be measured and paid for separately) as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing 1st class deodar wood. 12 ( twelve )mm thick 150 ( one five Zero)mm wide pelmet with 25 ( twenty five ) mm diametre wooden curtain rods and brackets including fixing 25x3 ( Twenty five into three ) mm M.S. flat at 10 ( ten) cm. Long and plugs etc complete as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

P/F 6 mm ( Six milimeter ) thick Fiber cement board ceiling of approved quality with butt jointing and nail (frame work and cover fillets to be paid for separately as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

P/F Rai Wood Planks in false Ceiling (frame work and cover fillets to be paid for separately as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing Sound Insulation of Himalayan acoustics made of 50mm thick under deck insulation 500 ( Five hundred) gsm with the backing of aluminum foil to be fixed under ms roof held with weld mesh wire and hardware as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing Prepainted steel sheet roofing over steel members/trusses, prepainted galvanised steel of TATA Durashine hot dip metalic zinc coated sheet with the top coat of regular modified polyster (RMP)organic coating of 20(twenty)micron over 5(five) micron runner plus back coat of polyster of micron over 5(five) microns primer coating 0.60mm(zero point sixty milimeter) thickness (having 1060 mm(one thousand sixty milimeter) covered with over all width 1126mm(one thousand one hundred twenty six milimeter) as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing ridges or hips 60 cms(sixty centimeters)overall in prepanted galvanised steel hot dip metalic zinc coated sheet TATA Durashine with the top coat of regular modified polyster (RMP) organic coating of 20(twenty)micron) over 5(five)micron runnerplus back coat of polyster of micron over 5(five) microns primer coating 0.60mm(zero point sixty milimeter) thickness (having 1060 mm(one thousand sixty milimeter) covered with over all width 1126mm(one thousand one hundred twenty six milimeter)fixed with J or L hooks 8mm(eight milimeter) dia with limpet and bitumen washers complete including carriage of materials within all leads, lifts and other incidentals complete as per entire satisfaction of the Engineer-in-Charge as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing M.S. Black sheet in Chajja and Soffits and Gable end of roof as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing PGI Gutter 30cm(thirty centimeter) wide 120cm(one hundred twenty centimeter) over all Box type gutter with 0.60mm(zero point sixty milimeter) thick as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing M.S. Sheet 1.66mm(one point sixty six milimeter) to 2mm(two milimeter) thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-Charge(Base members of steel work shall be measured and paid separately as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing 100 mm ( hundred milimeter ) diameter on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 ( ten) mm gap for thermal expansion, (i) Single socketed pipes. including filling the joints with approved adhesive complete including carriage of materials within all leads and lifts as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing on wall faces PVC (D-Plast) accessories for rain water pipes including filling the joints with approved adhesive complete as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

110 mm I(one hundred Ten milimeter) dia PVC plain Bend.

110 mm I(one hundred Ten milimeter) dia PVC Collars..

110 mm I(one hundred Ten milimeter) dia PVC Plain shoes.

Providing and fixing 110 mm ( one hundred ten milimeter )PVC holder bat clamps including steel bolts to centralized PVC pipe embedded in and including cement concrete block 100*100*100 ( hundred into hundred into hundred ) mm One hundred into one hundred into one hundred milimeter) of 1:2:4(one cement: two sand: four graded stone aggregate 20 mm.(twenty milimeter) nominal size)including cutting of holes and making good the Walls: as per HP.PWD specification 1990 (One thousand Nine hundred Ninety) Volume-I, including carriage of all labour equipments and materials to various location of site through all modes of transportation in all leads and lifts, including all iincidential charges.

Providing and fixing Single socketed pipes 75mm (Seventy five millimetre) dia of Supreme/Fenolax/D-plast/ Vectus make on wall face unplasticised Rigid PVC (Polyvinyl chloride) rain water pipes conforming to IS : 13592 (indian standard : thirteen thousand five hundred ninty two ))Type A, complete upto floor all level as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing M.S Flat grills of required pattern in wooden frames of windows etc. with M.S flats square or rounded bars with round headed bolts and nuts or by screws as per the direction of Engineer-in-Charge.and as per HP.PWD. Specification 1990 volume-I, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Steel work welded in built up sections, trusses and framed work, including cutting, hoisting in all heights and levels, fixing in position and applying a priming coat of red lead paint complete as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

In beams joists channels, angles, tee, flats with connecting plates or angle cleats as in main and cross beams, hip and jack rafters, purlins connecteed to common rafters and the like.

In gratings framed guard bars, ladders, railing, brackets and similar class work

Providing and fixing hand rail of M.S. hollow pipe (D-section) overall 50 mm (Fifty milimeter) welded with M.S. horizontal M.S. flat 40mmx5 mm (forty into Five milimeter)including one coat of oxide priming coat complete (M.S. flat and balusters of railing shall be measured and paid for separately).as per HP.PWD specification 1990 (One thousand Nine hundred Ninety) Volume-I, including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts , including all incidental charges .

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing Vibro Hydraulically compressed and polished terrazzo tiles IS marked ISI 1237 ( twelve thirty seven) in skirting , risers of steps on 10 mm ( ten milimeter ) thick cement mortar 1:3 ( one isto three ) The sample of the tile shall be got approved from higher authority, as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and laying 1.8 MM ( one point eight milimeter) Thick Heavy duty Anti Static Vinyle flooring as per HP.PWD. Specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all floors including all leads lifts and all incidental charges.

Providing and fixing 10 mm ( ten Milimeter ) thick acid and/or alkali resistant tiles on flooring 300x300 mm ( three into three hundred milimeter ) of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement In flooring on a bed of 10 mm ( ten milimeter) thick mortar 1:4 (1 acid proof cement : 4 coarse sand) as per IS : 4457, complete as per the direction of Engineer-in- Charge as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing 10 ( ten )mm thick acid and/or alkali resistant tiles on Dado /Skriting 300x300 mm ( three into three hundred milimeter )of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement In flooring on a bed of 12 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) as per IS : 4457, complete as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm ( three into three hundred milimeter ) (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 ( one five six two two) of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 ( twenty ) mm thick cement mortar 1:4 (one Cement isto four Coarse sand), Jointing with grey cement slurry @ 3.3 ( three point three ) kg/sqm ncluding pointing the joints with white cement and matching pigment etc., complete as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing 1st quality 200x300 ( Two hundred into three hundred) mm size Ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 ( twelve ) mm thick bed of cement Mortar 1:3 (one cement: three coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and laying Vibro Hydraulic Compressed Chequered Terrazzo Tiles with Semi Round Nosing 300x200x25 ( three hundred into two hundred into twenty five ) mm in Treads as per HP.PWD specification 1990(One thousand Nine hundred Ninety) volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and Laying Cement concrete 40 (Forty) millimeters thick flooring in 1:2:4 (One cement isto Two sand isto Four graded crushed hard stone aggregate 20 (twenty) millimeters nominal size) laid in One layer finished with floating coat of neat cement in all floors up to all heights, levels complete as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and laying flamed finish Granite Stone Flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 ( eighteen mm thick stone slab over 20 ( twenty ) mm (average) thick base of cement mortar 1:4 (one cement : four coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

6(Six) millimeters thick plaster to ceiling in cement mortar 1:3(One cement isto Three sand) in all floors up to all heights and levels, as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

20 mm ( Twenty milimter ) cement plaster plaster in single coat on brick/concrete/stone walls for interior/exterior plastering up to all heights including arises. Internal rounded angles, chamfers and/or rounded angles not exceeding 80(Eighty) millimeters in girth and finished even and smooth in cement mortar 1:4 (One cement isto Four sand), including scaffolding etcas per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

25 mm ( twenty five milimter ) thick mud plastering on mud brick wall in fair / rough side of single coat as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Distempering with 1st quality Acrylic distemper (ready mixed) of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Finishing with Deluxe Synthetic Enamel paint system for interiors and exteriors using Primer as per manufacturers specifications Two or more coats applied on walls @ 1.25 ( one point two five ) ltr/10 ( ten) sqm over and including one coat of Special primer applied @ 0.75 ( zero point seven five) ltr /10 ( ten ) sqm as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Applying Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 (zero point ninty) ltr/10 ( ten )sqm over an under coat of primer applied @0.75 ( zero Point seven five ) ltr/10 (Ten )sqm of approved brand and manufacture as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ( Zero point Ninty ) ltr/10 ( ten) sqm over an under coat of primer applied @ 0.80 ( zero Eighty) ltr/10 ( ten) sqm of approved brand and manufacture as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and laying 80 ( Eight) mm thick factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 ( fifty)mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing, laying and jointing 23 ( twenty three) CM Half Stone ware pipe stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (one cement : one fine sand) includingtesting of joints etc. complete as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 ( hundred) mm sand cast Iron P or S trap, 10 ( ten) litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231( seven two htree one), with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440( Five Eight Zero into Forty Four) mm with integral type foot rests as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing vitreous China dual purpose closet suitable for use as squatting pan or European type water closet (Anglo Indian W.C pan) with seat & lid fixed with C.P. brass hinges and rubber buffers, 10( ten)litre low level flushing cistern with fitting and brackets, 40( forty ) mm flush bend, 20( twenty ) mm over flow pipe, with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: White vitreous china dual purpose WC pan with white solid plastic seat and lid with white vitreous china flushing cistern and C.P. flush bend as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing Solid plastic seat with lid for pedestal type W.C. pan complete : White solid plastic seat with lid as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing & fixing white vitreous china water less urinal of size 600 x 330 x 315 ( six hundred into three fifteen) mm having antibacterial /germs free ceramic surface, fixed with cartridge having debris catcher and hygiene seal as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing Wash basin with C.I. brackets, 15 ( fifteen) mm C.P. brass pillar taps, 32 ( thirty two) mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 ( Six hundred thirty into four hundred five) mm with a pair of 15 ( fiftten)mm C.P. brass pillar taps as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing C.P. brass chain and rubber plug complete for sink or wash basin: 32 ( thrity Two) mm dia as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing 600x450 ( Six hundred into four hundred fifty ) mm beveled edge mirror of superior glass (of approved quality) complete with 6 ( six ) mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing PTMT liquid Soap container 109 ( one hundred nine ) mm wide, 125 ( one hundred twenty five ) mm high and 112 ( one hundred twelve ) mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 ( one hundred five ) gms as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing PTMT Towel Ring trapezoidal shape 215 ( two fifteen) mm long, 200 ( twp hundred ) mm wide with minimum distances of 37 ( thirty Seven) mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 ( Eight Eight) gms as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing PTMT Soap Dish Holder having length of 138 (One hundred Thirty eight )mm, breadth 102 ( one hundred two) mm, height of 75 ( seventy Five )mm with concealed fitting arrangements, weighing not less than 106 gms as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing Toilet Paper Holder of C.P. brass as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 ( Eight Nine three one ) 15 ( Fifteen) mm nominal bore as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing C.P. Brass stop cock concealed) of standard design and of approved make conforming to IS:8931 ( Eight Nine three one ) 15 ( Fifteen) mm dia as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 ( Eight Nine three one ) as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing uplasticised PVC connection pipe with brass unions :- 45 ( forty five) cm length :- 15( Fifteen) mm nominal bore as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing gun metal Gate valve with C.I. wheel of approved quality (screwed end) as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450( one five four five zero), U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C ( eighty), including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00( one ) metre spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge Concealed work, including cutting chases and making good the wall etc. as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 ( one two seven zero one ) marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors 100 mm inlet and 100 mm outlet Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing high pressure UPVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete. including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. single equal branch,oval access door,collars, "P" or "S" trap etc., with clamps at 1.20 One point two zero) metre spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge Concealed work, including cutting chases and making good the wall etc.

110 mm dia.

75 mm dia.

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete. as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

110 mm dia.

75 mm dia.

Providing and fixing Single socketed pipes 110mm (one hundred ten millimetre) dia of Supreme/Fenolax/D-plast/ Vectus make on wall face unplasticised Rigid PVC (Polyvinyl chloride) rain water pipes conforming to IS : 13592 ( one three five nine two)(indian standard : thirteen thousand five hundred ninty two ))Type A, including jointing with seal ring conforming to IS : 5382 ( five htree eight two) (indian standard : five thousand three hundred eighty two), leaving 10 mm ( ten millimetre) gap for thermal expansion as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 31 ( thirty one ) mm dia of 79 ( seventy Nine) mm length and 62 ( sixty two) mm breadth weighing not less than 45 ( forty five) gms as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing PTMT jet spray of approved quality and colour with one metre tube pipe with necessary fitting etc. complete as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing to the inlet mouth of rain water pipe PTMT (an Engineering Thermoplastic) grating square(Slit) 150 ( one hundred fifty) mm square with a height of 8 ( eight) mm andweighing not less than 100 ( one hundred ) gms.as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 ( three hundred into three hundred) mm size (inside) the weight of cover to be not less than 4.50 ( four point fifty )kg and frame to be not less than 2.70 ( two point seven) kg as per standard design: 150 x 100 ( one hundred fifty into one hundred ) mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 ( Seven point five) Round Mouth Traps: 100mmx100 ( one hundred into one milimtermm) size P or S type as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement : one point five coarse sand (zone- III) : three graded stone aggregate 20 ( twenty ) mm nominal size), foundation concrete 1:4:8 mix (one cement : four coarse sand (zone- III) : eight graded stone aggregate 40 ( forty )mm nominal size), inside plastering 12( twelve ) mm thick with cement mortar 1:3 (one cement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20 ( twenty )mm nominal size) finished with a floating coat of neat cement complete as per standard design as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Inside size 800mm x 800mm and 500mm ( Eight hundred into eight hundred and five hundred) deep including C.I cover with frame. (Light duty single seal pattern - 1) 455 mmx610mm ( four hundred fifty five into six hundred ten milimeter ) internal dimensions total weight of cover and frame to be not less than 38 ( thirty eight )kg . (weight of cover 23 ( twenty three) kg and weight of frane 15( fifteen) kg.)as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 ( Seven point five ) as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Inside size 800 mm x 800 mm and 1000 mm ( Eight hundred into eight hundred and Ten hundred) deep including C.I cover with frame. (Light duty single seal pattern - 1) 455mmx610mm ( four hundred fifty five into six hundred ten milimeter ) internal dimensions total weight of cover and frame to be not less than 38 (thirty eight) kg . (weight of cover 23 ( twenty three) kg and weight of frane 15 ( Fifteen) kg.) as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

(a) With 300mm ( three hundred milimter ) thick walls of squarred rubble masonry coursed with hard stones of approved quality in cement mortar 1:3 (one cement : three sand). as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40 ( forty Milimeter ) mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Constructing masonry Chamber 60x60x75 cm,(sixty into sixty into seventy five cenitimetert) inside in brick work in cement mortar 1:4 (one cement : four coarse sand) for fire hydrants, with C.I. surface box 350x350 mm (three hundred fifty into three hundred fifty millimeter) top and 165 mm(one hundred sixty five millimeter) deep ( inside) with chained lid and RCC top slab 1:2:4 mix (one cement : two coarse sand : four graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 (one cement : five fine sand:ten graded stone aggregate 40 mm(forty millimeter)_nominal size) and inside plastering with cement mortar 1:3 (one cement : three coarse sand) 12 mm (twelve millimeter)thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5)seven point five) complete upto floor all level as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Constructing soak pit 1.20x1.20x1.20 m(one point twenty into one point twenty into one point twenty meter) filled with brickbats including S.W. drain pipe 100 mm (hundred millimeter) diam complete upto floor all level as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing 75mm(Seventy five millimeter) PVC (Polyvinyl chloride) Cowl complete upto floor all level as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing in position pre-cast R.C.C.(reinforced cement conceret) manhole cover and frame of required shape and approved quality Circular shape 450(four hundred fifty) mm internal diameter complete upto floor all level as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges.

Wiring for light point / fan point / exhaust fan / call bell point with 1.5 ( one point five )Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit with modular switch, modular plates, suitable G.I. box and earthing the light point with 1.5 ( one point five ) Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required.

Group A.

Group C.

Wiring for twin control light point with 1.5 ( one popint five ) Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit, with 2 ( two)-way modular switch, modular plates, suitable G.I. box and earthing the light point with 1.5( one point five ) Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required.

Group C.

Providing and installation of following type of Ultra slim decorative LED Batten with extruded aluminium heat sink, with antiglare polycarbonate diffuser and energy efficient constant current, integral electronic driver, suitable for input voltage: 220-240 V, 50/60 ( two two zero- two four zero v fifty /sixty)Hz, complete with all accesories, including mounting clips & loop in loop out wire, connections, testing and commissioning etc. as required, with two year warranty. Make: Panasonic, Havells, Philips or any other approved by Engineer-in-Charge.

LED Batten Light 20 ( twenty)Watt. (Length 4 ( four )-Ft.)

Providing and installation of following type of Ultra slim decorative LED Batten with extruded aluminium heat sink, with antiglare polycarbonate diffuser and energy efficient constant current, integral electronic driver, suitable for input voltage: 220-240 V, 50/60 ( two two zero- two four zero v fifty /sixty) Hz, complete with all accesories, including mounting clips & loop in loop out wire, connections, testing and commissioning etc. as required, with two year warranty. Make: Panasonic, Havells, Philips or any other approved by Engineer-in-Charge..

LED Mirror Batten Light 10 ( Ten)Watt. (Length 2 ( two)-Ft.)

Providing and installation of following type of Surface/Recess mounting square/round type LED Panel Light, powder coated housing made of CRCA sheet, suitable for input voltage: AC 220-240 V, 50/60 ( two two zero- two four zero v fifty /sixty) Hz, complete with all accessories, including making connections, testing and commissioning etc. as required with two years warrenty. Make: Panasonic, Havells, Philips or any other approved by Engineer-in-Charge.

LED Panel Light 12 ( twelve ) Watt.

LED Panel Light 18 ( eighteen)Watt.

Providing and installation of following type of Surface/Recess mounting square/round type LED Panel Light, powder coated housing made of CRCA sheet, suitable for input voltage: AC 220-240 V, 50/60 ( two two zero- two four zero v fifty /sixty) Hz, complete with all accessories, including making connections, testing and commissioning etc. as required with two years warrenty. Make: Panasonic, Havells, Philips, Twinkle or any other approved by Engineer-in-Charge.

LED Panel Light 34 ( Thirty four) Watt. (Size:- 2 x 2 ( two into two) Feet)

LED Panel Light 40 ( forty )Watt. (Size:- 1 x 4 ( one into four ) Feet)

Providing and installation of Globe Type wall bracket made up of Polycarbonate, suitable for 9W LED lamp B22 ( twenty two) base. for indoor applications, complete with all accessories, including making connections, testing and commissioning etc and excluding LED Lamp. as required. Make: Havells or any other approved by Engineer-in-Charge.

Decorative wall Bracket.

Providing and installation of following type of LED retrofit lamp B-22 ( twenty two ) holder base with polycarbonate body and aluminium heat sink; suitable for input voltage: AC 220-240 V, 50/60 ( two two zero- two four zero v fifty /sixty)Hz, including mounting in existing fixture, testing etc. as required complete in all respects. Make:-Havells or any other approved by Engineer-in-Charge.

LED retrofit lamp 9 ( nine )W.

Providing and installation of following type of LED Street light fitting made of pressure die cast aluminium housing powder coated with weather proof gasket ensuring IP-66 ( sixty six ) protection, Heat resistant toughened glass,High Efficiency Street Lighting Lenses, Inbuilt 4 ( four )KV Surge protection, complete with all accessories including making connections, testing etc. as required with two years warrenty. Make: Panasonic, Havells, Philips, Twinkle or any other approved by Engineer-in-Charge.

LED Street Light 45 ( forty five )Watt. (Size:- pole dia 40 ( forty ) mm max.)

Supplying and erection of street light bracket made of G.I. pipe 'A' class of suitable length and dia, the pipe bended to give an angle of 100 to 110 ( one hundred to one hundred ten ) degree fitted with bolt & nuts at the top of existing pole or wall including painting the pipe with two coats of approved paint over priming coat complete in all respects as required.

40 mm dia. G.I. pipe, heavy class

Providing and installation of exhaust fan of following sizes in the existing opening, including making the hole to suit the size of the above fan, making good the damages, connections, testing and commissioning etc. as required:- Make: Crompton, Standard, Bajaj, Orient Electric or any other approved by Engineer-in-Charge.

Exhaust Fan, Light duty, (Domestic) 230 ( two three zero) mm sweep

Exhaust Fan, Heavy duty, 450 ( Four five Zero) mm sweep

Providing and fixing of Iron shutter for all sizes exhaust fans in the existing opening, including installation at site etc. as required to the best satisfaction of Engineer-in-Charge.

Supplying and fixing Ding-Dong / Electronic musical bell, suitable for D.C./A.C. single phase,230 ( two thee zero) volts complete as required.

Providing and installation of surface mounted, LED Bulk head Fitting IP65 protection, comprising of high brightness LEDs, suitable for input voltage: AC 220-240 V, 50/60 ( two two zero -two four zero v fifty /sixty)Hz, complete with all accessories, including making connections, testing and commissioning etc. as required with Two years warrenty.. Make: Panasonic, Havells, Philips or any other approved by Engineer-in-Charge.

LED Bulk Head Fitting 12 ( twelve ) Watt.

Supplying and fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required.

5/6( five /six ) amps. 1-way Modular switch

3 ( three)pin 5/6 Five /six )amps. Modular socket outlet.

Supplying and fixing electrical switch board, having 3 ( three) No. of 5/6 ( five /six )amp. Modular Switches and Modular Socket on suitable size of G.I. modular boxes of 12( twelve ) modules (205mmx135mmx60mm)( two zero five into one three five into sixty ) deep ( nominal size) on surface or in recess with suitable size along with modular base and cover plate for modular switches in the front including providing and fixing 3 No. 3 ( three) pin 5/6 ( five /six )amp modular socket outlet and 5/6 amp modular switch, connection, painting etc.as required. (For Light Plug/Computer Points)

Supplying and fixing G.I. Modular box of (140mmx78mmx50mm)( one four zero I into seventy eight into fifty ) size with modular plate and cover in recess including providing and fixing 6 ( six )pin 15/16( fifteen/sixteen) amps modular socket outlet and 15/16( fifteen /sixteen) amps, modular switch, connections etc. as required.

Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required.

2x1.5 ( two into one point five ) Sq. mm.

4x1.5 ( four into One point five )Sq. mm.

2x2.5 ( two into two point five ) Sq. mm.

4x2.5 ( four into two into five ) Sq. mm.

2x4 ( two into four )Sq. mm.

4x4 ( Four into four)Sq. mm.

2x10 ( two into ten) Sq. mm.

2x16 ( two into six) Sq. mm.

Wiring for circuit / sub-main with 4x6 ( four into six)Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 2 No.6 Sq.mm. (4x6+2x6) ( four into six plus two into six)HRFRLS/PVC insulated single core copper conductor cable for earthing as required.

Wiring for circuit / sub-main with 4x10 ( four into ten)Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 2 No.10 Sq.mm. (4x10+2x10) ( four into ten plus two into ten)HRFRLS/PVC insulated single core copper conductor cable for earthing as required.

Wiring for circuit / sub-main with 3x25+1x16 ( Three into twenty five plus one into sixteen) Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 2 No.16 Sq.mm. ( two no sixteen SQM) (3x25+3x16) ( Three into twenty five plus three into sixteen) HRFRLS/PVC insulated single core copper conductor cable for earthing as required.

Supplying and erection of 6( six) amps. to 32 ( thirty two) amps. rating, 10 ( ten) KA breaking capacity, 240 ( two foue zero) volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required. Make: L&T, Havells or any other approved by Engineer-in-Charge.

Single pole 5/6 ( five /six)Amp. Cat-A.

Single pole 10 ( ten) Amp. Cat-A.

Single pole 15/16 Amp ( Fifteen/Sixteen). Cat-A.

MCB Double Pole 20 ( twenty)Amp.

MCB Double Pole 32 ( thirty two)Amp.

Supplying and fixing following rating, double pole (single phase & neutral) 240 ( two four zero) volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 ( Three zero) miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required. . Make: L&T, Havells or any other approved by Engineer-in-Charge.

RCCB Double Pole 16 ( sixteen) Amp.

RCCB Double Pole 25 ( twenty Five )Amp.

RCCB Double Pole 40 ( forty )Amp.

Supplying and erection of 6 ( six ) amps. to 32 ( thirty two) amps. rating, 10 ( Ten) KA breaking capacity, 415 ( four one five )volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required. Make: L&T, Havells or any other approved by Engineer-in-Charge.

MCB Four Pole 16 ( sixteen) Amp.

MCB Four Pole 25 ( twenty five )Amp.

Supplying and fixing following rating, Four pole (Three phase & neutral) 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required. . Make: L&T, Havells or any other approved by Engineer-in-Charge.

RCCB Four Pole 16 ( sixteen) Amp.

RCCB Four Pole 25 ( twenty five )Amp.

Supplying and fixing of following way TPN HORIZONTAL PPI (PER PHASE ISOLATION) DBs of 6 to 12-( six to Twelve)Way DD, FP MCB /Isolator /RCCB/RCBO as incomer, of suitable dimensions made from 1.6 ( One point six)mm thick CRCA sheet on surface / recess with Incomer FP MCB spreader links, busbar, 8( Eight) module incomer and DP RCCB/RCBO as sub-incomer with 6 to 12 ( six to twelve)module MCBs as outgoing, complete with tinned copper bus- bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, cable, identification labels interconnections, phosphatized and powder painted, Metal Door IP 43( forty three) including earthing etc. as required. Make: L&T, Havells or any other approved by Engineer-in-Charge.

TPN DB PPI Double Door 6 ( six)-Way.

TPN DB PPI Double Door 8(Eight)-Way.

TPN DB PPI Double Door 12( Twelve)-Way.

Supplying and fixing of following way, single pole and neutral sheet steel MCB distribution board, 240( Two four Zero) volts, on surface / recess, complete with tinned copper bus- bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required. Make: L&T, Havells or any other approved by Engineer-in-Charge.

Double Door 8 (Eight)-Way.

Double Door 12 ( Twelve)-Way.

Providing, laying and fixing of one No. aluminium conductor, PVC insulated and PVC sheathed, armoured/XLPE power cable, working voltage 1100( one one zero zero) volts grade on surface etc. of the required size:-

Armoured cable 16 ( Sixteen ) sq. mm (2( Two)-core)

Armoured cable 25( Twenty five ) sq. mm (3.5 ( Three point five )-core)

Earthing with G.I earth pipe 4.5 ( Forty point five ) mtr. long and 40 ( Forty)mm dia, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required.

Extra for using salt and charcoal for pipe earth electrode complete as required

Providing and fixing 6 ( Six) SWG (4 ( Four)mm dia.) G.I. wire on surface or in recess for loop earthing as required.

Providing and fixing 6 ( Six)SWG (4 ( Four) mm dia.) G.I. wire on surface or in recess for loop earthing along with existing surface/recessed conduit/sub-main wiring/cable as required.

Providing and fixing of following type Kit-kat Rewireable (Porcelain Fuse carrier & Base) fuse suitable for input voltage 415 ( Four one five ) V, 50/60 ( Fifty /sixty) Hz, complete in all respect as required:- Make: L&T, Havells or any other approved by Engineer-in-Charge.

Kit-Kat Fuse 63 ( Sixty Three)Amp. 415 ( Four one five )Volt

Supplying & fixing wooden boxes of following sizes (nominal size) on surface or in recess suitable for fixing phenolic laminated sheet cover in front including painting etc. as required:-

203mm.x 254mm.x60mm.( Two zero three into two five four into sixty) Deep

Providing, fixing and installation of following rating and breaking capacity MCCB with Thermal Release Having inbuilt Overload and Short Circuit Protection with enclosure cubical panel board including drilling holes in the cubical panel, suitable for input voltage: 415/500 ( Four one five /five zero zero) Volt AC, 50( Fifty) Hz, complete with all accesories, including making connections, testing and commissioning etc. as required, Make:- L&T, Havells or any other approved by Engineer-in-Charge.

MCCB 63 ( Sixty Three)Amp. -10 ( Ten) KA

Supplying and fixing sheet metal bus-bar chamber suitable for 63 ( Sixty Three) Amp. 415 ( Four one five )volts capacity with 4 No. copper strip bus-bars each of sutibale length & cross-sectional area , enclosure made from 1.6( One point Six) mm thick M.S. sheet having overall dimensions (380mmx350mmx150mm ( Three Eight Zero into Three Five Zero into One Five Zero) nominal with all accessories including connections, earthing the body etc. as required.

Bus-Bar 63 ( Sixty Three) Amps 6 9 ( Six)-Way.