Electrical panel up-gradation

Amount

CIVIL WORKS(Cable Trench)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:

Cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources)

15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix :

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.

All kinds of soil

Demolishing R.B. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in- charge.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

FILLING SOIL & DEBRISES:Filling under floors with debris / murrum available or brought from outside sources spreading in 200mm thick layer, watering consolidating to 150mm thickness and finished to desired levels etc. complete (17 M2 x 0.3m depth). ( disposing / taking away the debris outside the premises & disposing as per the guidlines of statutory authoritised. )

Filling debris brought from outside

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

15 mm cement plaster on the rough side of single or half brick wall of mix :

1:4 (1 cement: 4 fine sand)

CIVIL WORKS(IRON FENSING)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:

Cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources)

15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix :

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

FILLING SOIL & DEBRISES:Filling under floors with debris / murrum available or brought from outside sources spreading in 200mm thick layer, watering consolidating to 150mm thickness and finished to desired levels etc. complete (17 M2 x 0.3m depth). ( disposing / taking away the debris outside the premises & disposing as per the guidlines of statutory authoritised. )

Filling debris brought from outside

15 mm cement plaster on the rough side of single or half brick wall of mix :

1:4 (1 cement: 4 fine sand)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion

Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).

Extra for levelling & neatly dressing of disposed soil completely as directed by Engineer-in-charge.

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge.

Powder coated minimum thickness 50 micron aluminium tubular handle bar

Providing and fixing Brass 100 mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete

ELECTRICAL WORKS

OPD Building(Change Over Panel)

Supply, Installation, Testing & Commissioning of L.T Panel, cubicle type, made out of min 2mm thick CRCA sheet (load bearing), totally enclosed, IP42, free standing, floor mounting, dust and vermin proof, powder coated, indoor, compartmentalised, suitable for operation on 3 phase and neutral, 415 V, 50Hz AC system with busbars extendable on both sides, including internal wiring with suitable size wires, rotary handle, spreaders, 3mm thick gland plate, hinged type door with neoprene / PU gasket, IS 8623 etc. The panel shall include supply & installation of following switchgears, metering instruments and accessories as per specification. The panel shall be suitable for receiving Cable / Bus duct to the incomer of source. Panel shall have potential free contacts to interface with BMS in future..

Incomer

1000A,TPN, 65kA, microprocessor based ACB electrical operated, drawout type, motorised, with overload, instantaneous SC, delayed SC, and ground fault protection with necessary communication port, shunt trip coil, U/V release etc - 2 nos.

1000A Four Pole (4P / FP) Onload Manual Changeover Switch, 415 V AC-1 nos.

Busbar

1000 A TPN, 35kA busbars of high conductivity electrolytic quality Aluminium alloy and suitable size earthing conductor through out the panel for its earthing. Bus Bar Shall have 100% neutral.

Instruments

2A, C curve SP MCB - 4 set

RYB indication lamp, LED type - 4 set

On/Off, Trip indication lamp, LED type - 4 set

1 set 3 phase Digital Multi function meter to read V, A, F, kW, PF, kWH, Acc class 1 and with necessary communication port (Backnet/Modbus/RS:485) suited for BMS system

1000/5A 15VA class 1 resin cast CT - 1 set

Outgoing.

630A FP 50kA MCCB with microprocessor based release with adjustable OL, SC and EF protection - 3 nos.

400A FP 35kA MCCB with microprocessor based release with adjustable OL, SC and EF protection - 1 nos.

The switchboard shall be complete with all inter connections, risers, internal wiring, labels etc complete as required

Old Hospital Building Panel-1

Supply, Installation, Testing & Commissioning of L.T Panel, cubicle type, made out of min 2mm thick CRCA sheet (load bearing), totally enclosed, IP42, free standing, floor mounting, dust and vermin proof, powder coated, indoor, compartmentalised, suitable for operation on 3 phase and neutral, 415 V, 50Hz AC system with busbars extendable on both sides, including internal wiring with suitable size wires, rotary handle, spreaders, 3mm thick gland plate, hinged type door with neoprene / PU gasket, IS 8623 etc. The panel shall include supply & installation of following switchgears, metering instruments and accessories as per specification. The panel shall be suitable for receiving Cable / Bus duct to the incomer of source. Panel shall have potential free contacts to interface with BMS in future..

Incomer

400A,TPN, 65kA, microprocessor based MCCB electrical operated, with overload, instantaneous SC, delayed SC, and ground fault protection with necessary communication port, shunt trip coil, U/V release etc - 1 nos.

Busbar

400 A TPN, 35kA busbars of high conductivity electrolytic quality Aluminium alloy and suitable size earthing conductor through out the panel for its earthing. Bus Bar Shall have 100% neutral.

Instruments

2A, C curve SP MCB - 4 set

RYB indication lamp, LED type - 4 set

On/Off, Trip indication lamp, LED type - 4 set

1 set 3 phase Digital Multi function meter to read V, A, F, kW, PF, kWH, Acc class 1 and with necessary communication port (Backnet/Modbus/RS:485) suited for BMS system

400/5A 15VA class 1 resin cast CT - 1 set

Outgoing.

Supply and Installation of 250A FP 50kA MCCB with microprocessor based release with adjustable OL, SC and EF protection - 1 nos.

Supply and Installation of 160A FP 50kA MCCB with microprocessor based release with adjustable OL, SC and EF protection - 3 nos.

Supply and Installation of 125A FP 50kA MCCB with microprocessor based release with adjustable OL, SC and EF protection - 4 nos.

Supply and Installation of 100A FP 10kA MCB - 3 nos.

Old Hospital Building Panel-2

Supply, Installation, Testing & Commissioning of L.T Panel, cubicle type, made out of min 2mm thick CRCA sheet (load bearing), totally enclosed, IP42, free standing, floor mounting, dust and vermin proof, powder coated, indoor, compartmentalised, suitable for operation on 3 phase and neutral, 415 V, 50Hz AC system with busbars extendable on both sides, including internal wiring with suitable size wires, rotary handle, spreaders, 3mm thick gland plate, hinged type door with neoprene / PU gasket, IS 8623 etc. The panel shall include supply & installation of following switchgears, metering instruments and accessories as per specification. The panel shall be suitable for receiving Cable / Bus duct to the incomer of source. Panel shall have potential free contacts to interface with BMS in future..

Incomer

400A,TPN, 65kA, microprocessor based MCCB electrical operated, with overload, instantaneous SC, delayed SC, and ground fault protection with necessary communication port, shunt trip coil, U/V release etc - 1 nos.

Busbar

400 A TPN, 35kA busbars of high conductivity electrolytic quality Aluminium alloy and suitable size earthing conductor through out the panel for its earthing. Bus Bar Shall have 100% neutral.

Instruments

2A, C curve SP MCB - 4 set

RYB indication lamp, LED type - 4 set

On/Off, Trip indication lamp, LED type - 4 set

1 set 3 phase Digital Multi function meter to read V, A, F, kW, PF, kWH, Acc class 1 and with necessary communication port (Backnet/Modbus/RS:485) suited for BMS system

400/5A 15VA class 1 resin cast CT - 1 set

Outgoing.

Supply and Installation of 250A FP 50kA MCCB with microprocessor based release with adjustable OL, SC and EF protection - 1 nos.

Supply and Installation of 160A FP 50kA MCCB with microprocessor based release with adjustable OL, SC and EF protection - 3 nos.

Supply and Installation of 125A FP 50kA MCCB with microprocessor based release with adjustable OL, SC and EF protection - 4 nos.

Supply and Installation of 100A FP 10kA MCB - 3 nos.

Surgery Panel-1

Supply, Installation, Testing & Commissioning of L.T Panel, cubicle type, made out of min 2mm thick CRCA sheet (load bearing), totally enclosed, IP42, free standing, floor mounting, dust and vermin proof, powder coated, indoor, compartmentalised, suitable for operation on 3 phase and neutral, 415 V, 50Hz AC system with busbars extendable on both sides, including internal wiring with suitable size wires, rotary handle, spreaders, 3mm thick gland plate, hinged type door with neoprene / PU gasket, IS 8623 etc. The panel shall include supply & installation of following switchgears, metering instruments and accessories as per specification. The panel shall be suitable for receiving Cable / Bus duct to the incomer of source. Panel shall have potential free contacts to interface with BMS in future..

Incomer

250A,TPN, 65kA, microprocessor based MCCB electrical operated, with overload, instantaneous SC, delayed SC, and ground fault protection with necessary communication port, shunt trip coil, U/V release etc - 1 nos.

Busbar

250 A TPN, 35kA busbars of high conductivity electrolytic quality Aluminium alloy and suitable size earthing conductor through out the panel for its earthing. Bus Bar Shall have 100% neutral.

Instruments

2A, C curve SP MCB - 4 set

RYB indication lamp, LED type - 4 set

On/Off, Trip indication lamp, LED type - 4 set

1 set 3 phase Digital Multi function meter to read V, A, F, kW, PF, kWH, Acc class 1 and with necessary communication port (Backnet/Modbus/RS:485) suited for BMS system

250/5A 15VA class 1 resin cast CT - 1 set

Outgoing.

Supply and Installation of 160A FP 50kA MCCB with microprocessor based release with adjustable OL, SC and EF protection - 3 nos.

Supply and Installation of 125A FP 50kA MCCB with microprocessor based release with adjustable OL, SC and EF protection - 5nos.

Surgery Panel-2

Supply, Installation, Testing & Commissioning of L.T Panel, cubicle type, made out of min 2mm thick CRCA sheet (load bearing), totally enclosed, IP42, free standing, floor mounting, dust and vermin proof, powder coated, indoor, compartmentalised, suitable for operation on 3 phase and neutral, 415 V, 50Hz AC system with busbars extendable on both sides, including internal wiring with suitable size wires, rotary handle, spreaders, 3mm thick gland plate, hinged type door with neoprene / PU gasket, IS 8623 etc. The panel shall include supply & installation of following switchgears, metering instruments and accessories as per specification. The panel shall be suitable for receiving Cable / Bus duct to the incomer of source. Panel shall have potential free contacts to interface with BMS in future..

Incomer

250A,TPN, 65kA, microprocessor based MCCB electrical operated, with overload, instantaneous SC, delayed SC, and ground fault protection with necessary communication port, shunt trip coil, U/V release etc - 1 nos.

Busbar

250 A TPN, 35kA busbars of high conductivity electrolytic quality Aluminium alloy and suitable size earthing conductor through out the panel for its earthing. Bus Bar Shall have 100% neutral.

Instruments

2A, C curve SP MCB - 4 set

RYB indication lamp, LED type - 4 set

On/Off, Trip indication lamp, LED type - 4 set

1 set 3 phase Digital Multi function meter to read V, A, F, kW, PF, kWH, Acc class 1 and with necessary communication port (Backnet/Modbus/RS:485) suited for BMS system

250/5A 15VA class 1 resin cast CT - 1 set

Outgoing.

Supply and Installation of 160A FP 50kA MCCB with microprocessor based release with adjustable OL, SC and EF protection - 3 nos.

Supply and Installation of 125A FP 50kA MCCB with microprocessor based release with adjustable OL, SC and EF protection - 5nos.

RT Annexure Building Panel

Supply, Installation, Testing & Commissioning of L.T Panel, cubicle type, made out of min 2mm thick CRCA sheet (load bearing), totally enclosed, IP42, free standing, floor mounting, dust and vermin proof, powder coated, indoor, compartmentalised, suitable for operation on 3 phase and neutral, 415 V, 50Hz AC system with busbars extendable on both sides, including internal wiring with suitable size wires, rotary handle, spreaders, 3mm thick gland plate, hinged type door with neoprene / PU gasket, IS 8623 etc. The panel shall include supply & installation of following switchgears, metering instruments and accessories as per specification. The panel shall be suitable for receiving Cable / Bus duct to the incomer of source. Panel shall have potential free contacts to interface with BMS in future..

Incomer

400A,TPN, 65kA, microprocessor based MCCB electrical operated, with overload, instantaneous SC, delayed SC, and ground fault protection with necessary communication port, shunt trip coil, U/V release etc - 1 nos.

Busbar

400 A TPN, 35kA busbars of high conductivity electrolytic quality Aluminium alloy and suitable size earthing conductor through out the panel for its earthing. Bus Bar Shall have 100% neutral.

Instruments

2A, C curve SP MCB - 4 set

RYB indication lamp, LED type - 4 set

On/Off, Trip indication lamp, LED type - 4 set

1 set 3 phase Digital Multi function meter to read V, A, F, kW, PF, kWH, Acc class 1 and with necessary communication port (Backnet/Modbus/RS:485) suited for BMS system

400/5A 15VA class 1 resin cast CT - 1 set

Outgoing.

Supply and Installation of 250A FP 50kA MCCB with microprocessor based release with adjustable OL, SC and EF protection - 1 nos.

Supply and Installation of 160A FP 35kA MCCB with microprocessor based release with adjustable OL, SC and EF protection - 3nos.

Supply and Installation of 125A FP 35kA MCCB with microprocessor based release with adjustable OL, SC and EF protection - 4nos.

Panel Dismantling and Shifting

Dismantling, Shifting and Re-Installing of existing Electrical Panels complete set with all supporting accessiories compete to required destination within the campus. All machines, labour etc required shall be incude in this cost.

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) .

3 & 1/2 Core A2XFY

400.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :

VERSHA TECHNOTRADE PVT LTD (BID ID -3218831)

MS ASSAM ELECTRIC STORE (BID ID -3220609)