Renovation and Extension of ADGP office Retiming room and toilet init by way of solar Retrofitting at PHQ Agling Leh..

Amount

Providing & fixing upto floor five level precast cement concrete solid blocks including hoisting and setting in position in cement mortar 1:3 (1cement:3 coarse sand), cost of required centring, shuttering and curing complete 1:2:4 (1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20 mm nominal size)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with with water proofing cement compound @ 0.253kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm . This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and laying vitrified anti skid floor tiles in different size (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 of aproved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete size of tiles 600 mm x 600 mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 meters lead. For thickness of tiles 10 mm to 25 mm

12mm Cement plaster of mix:1 : 6 ( 1 cement : 6 fine sand) including all lifts, leads, carriage of the mnaterial.

Providing and applying white cement based putty of specified thickness, f approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 2 mm thick

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content.With water thinnable cement primer on wall surface having VOC content less than 50 grams/liter

Wall painting with premium acrylic emulsion paint of interior grade, aving VOC (Volatile Organic Compound) content less than 50 grams/ liter of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats

Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28 liter/10sqm) over and including base coat of exterior primer applied @ 2.20kg/10sqm

roviding and fixing precoated galvanized iron profile sheets (size, shape nd pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Providing and fixing precoated galvanised steel sheet roofing accessories0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-8 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm)

Providing valleys of 90cm wide overall in plain G.S. sheets fixed with polymer coated J. or L. hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.1.60 mm thick with zinc coating not less than 350 gram/m2

Providing and fixing plained eaves boarding. 2nd class Deodar wood 300x40 mm (nominal size) Complete job.

Providing and fixing of soffits made out 12mm thick imporyed wood planks including underneath frame work and scaffolding carriage complete (Badloo work?)

Demolishing og brick/ block work manually/ mechanically includin g stackinbg ofr servicreable material and uspposal of unserviceable material (in cement5 mortar)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS:277 and consisting of angle cleats of size 25 mm widex1.6mm thick with flanges of 27mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm diax40mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.5mm of required length with nuts & bolts of equired size and other end of angle hanger fixed with G.I. channels 45x15x0.9 mm running at the spacing of 1200 centre to centre, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having clips of 10.5 mm at 450mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm diaX230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre to centre, with 25mm long drive-all screws @ 230 mm interval ,including fixing of gypsum board/calcium silicate board o ceiling section and perimetre channel with the help of dry wall screws of size 3.5x25mm at 230mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the gypsum board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150mm on both sides of joint and two coats of primer suitable for board, all as per manufacturers’ specification and also including the cost of making openings for light fittings, grills diffusers, cutouts made with frame of perimetre channels suitably fixed all complete as per drawing and specification and direction of the Engineer-in-Charge but excluding the cost of painting with: 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095-Part 1 : 2011 (Board with BIS certification marks)

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded lazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shallbe also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately)

Providig and Fixing factory made UPVC door frame, made of UPVC extruded section, of size 65mmx55mm with wall thickness 2.0mm (± 0.2mm), corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side vertical of the farmes with PVC profile of size 28mm x30mm having wall thickness 2mm (±0.2mm), including providing and fixing 3nos of 125mm long stainless stell hinges to the frame, fixing with jamb with required number and size of anchor dash fasteners, all complete as per manufacture's specification and direction of Engineer-in-charge

Providing and fixingt 37mm thick factory made PVC door shutter, styles and rails made of PVC halloe section of suze 100mm x37mm wall thickness 2mm(± 0.2mm), with inbuilt bead on one side, styles and rails mitered cut and joint at he corners by means of 2 nos of plastic brackets of size 75mmx 220mm at each corneer and stainless steel screws, reinforcing the hinge side of style by inserting PVC porfile of size 28mm x30mm, with wall thicknss 2mm (±0.2mm),Lock rail of size 100mm z37mm, wall thickness 2mm (±0.2mm), will be fixed to the vertical iof styles. Providing with PVC sanapfit beads and panel of size 100mm x20mm, and inserting 2 nos tie bar of 6mm dia and fastening with nuts and washerds complete, all as per manufacturer's specification and direction os Engineer-in-charge

M/s SAMEER FAYAZ