DOOR TO DOOR MAINTENANCE ATTENDING ROUTINE COMPLAINTS OF MARRIED OTM ACCN CLEANING OF ROOF OVER HEAD SERVICE TANKS CLEARING AND REMOVAL OF BLOCKAGE OF ANY TYPE IN WC BATHROOM KITCHEN OF MD OTM BUILDINGS CLEANING OF SEWAGE LINES MANHOLES SEP

Amount

Note:- (a) Contractor shall detail his supervisor to office of AGE B/R (NORTH) daily by 9.00 AM who will report to concerned JE B/R /Engineer-in-Charge to receive all complaints related to (plumbing/carpenter/Sewage etc) of entire area under this contract. (b) Contractor shall provide service providers (sweepers) separately for all the Complaint cell as per the complaints list given along with all requisite tools, equipments, including safely measures for attending complaint and ensure completion report by 5.00 PM same day. (c) Complaint/blockage cleared any number of times on same day and at same location shall be treated as one complaint. (d) Please note that all the complaints relating to internal plumbing/sewage (WC/bath/kitchen etc) shall be attended within same day (within 12 hour). (e) In case any complaint pertaining to Plumbing/Sewage issue is not attended on same day, penalty @ Rs. 100/- per complaint shall deducted from contractor payments.

Taking down shutters of any description exceeding 1 Sq m but not exceeding 2 Sq m and Re-fixing in same opening complete all as specified and directed

Re-securing or easing & adjusting without taking down shutters of any description exceeding 1 sq m but n.exc 2 sq m each complete all as specified and directed

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for and disposing of debris outside MD land complete all as specified and as directed.

Demolition of cement concrete and paving not exceeding 15 cm thick (below or above ground level), removing debris outside MD land, complete all as specified and as directed.

Demolition of brick work / stone masonry / pack block masonry built in cement mortar of any description, removing debris outside MD land, all as specified and directed.

Dismantling of Fencing posts or struts (wood, steel RCC) any section, posts embedded in concrete, brick work, masonry etc, including taking out embedded portion and making good disturbed ground complete all as specified and as directed

Dismantling of Fencing posts or struts (wood, steel RCC) any section, posts embedded in natural ground including taking out embedded portion and making good disturbed ground complete all as specified and as directed

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and as directed.

Taking down cement plaster on brick or concrete or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc., complete and disposing the unserviceable material outside MD land complete all as specified and directed.

Excavating in post holes (or similar holes) each not exceeding 0.5 cum getting out in Hard / Dense soil , returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm etc complete all as specified and as directed

Excavating in trenches, in hard / dense soil, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 sq m on plan and getting out complete all as specified and as directed.

Returning, filling in (using soils), including spreading, leveling, watering and well ramming, soil in layers not exceeding 25 cm complete all as specified and as directed

Removing excavated surplus soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed

Cutting into existing manholes for connecting new drains ,making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in plain cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) and finishing the surfaces smooth and reforming benching as required for 160 mm bore pipe.

All as per Serial Item No 1.014 here-in-above, but for 200 mm bore pipe.

Demolition of concrete of any description as in bed concrete of pipe including breaking up drain pipes of 150 / 160 mm bore (Salt Glazed stone ware / AC / RCC / UPVC) set in cement mortar complete and removing the rubbish outside MD land, providing Material and labour, for Plain Concrete bed to 150 / 160 mm bore drain pipe including packing under and haunching against the sides of pipes, after they are laid and tested, with plain cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) complete all as specified and as directed. Note : Supply and laying pipes will be measured and paid for separately under respective items.

Demolition of concrete of any description as in bed concrete of pipe including breaking up drain pipes of 200 mm bore (Salt Glazed stone ware / AC / RCC / UPVC) set in cement mortar complete and removing the rubbish outside MD land, providing material and labour, for Plain Concrete bed to 200 mm bore drain pipe including packing under and haunching against the sides of pipes, after they are laid and tested, with plain cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) complete all as specified and as directed. Note : Supply and laying pipes will be measured and paid for separately under respective items.

Demolition of concrete of any description as in bed concrete of pipe including breaking up drain pipes of 300 mm bore (Salt Glazed stone ware / AC / RCC / UPVC) set in cement mortar complete and removing the rubbish outside MD land, providing material and labour, for Plain Concrete bed to 200 mm bore drain pipe including packing under and haunching against the sides of pipes, after they are laid and tested, with plain cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) complete all as specified and as directed. Note : Supply and laying pipes will be measured and paid for separately under respective items.

Material and labour for Plain Cement Concrete (1:4:8) type D2, using 40 mm graded stone aggregate as foundation filling, mass concrete, complete all as specified and as directed.

Material and labour, for Pre-cast cement concrete block masonry with grade ‘C’ solid blocks exceeding 10 cm in width, having minimum compressive strength of 50 Kg / Sq cm as per IS 2185 (Part- I) 2005 and set in CM 1:6 complete all as specified and as directed.

Material and labour, for PCC 1:2:4 type B-2 using 40 mm graded stone aggregate as in surface channels and drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitered/stopped ends etc. complete all as specified and as directed.

Extra for forming fair finished drain or channel 45 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitered/stopped ends etc. complete all as specified and as directed.

Material and labour for, Plain Cement Concrete, (1:2:4), type B0, using 12.5 mm graded stone aggregates as in coping, bed plates, water troughs and the like including weathering, lightly rounded or chamfered angles and throating, including necessary forms and moulds all as specified and as directed.

Material and labour, for Walling of random rubble stone masonry (Bangalore type), brought to courses, well bonded, bedded and solidly hearted, built in CM(1:6), complete all as specified and directed.

Material and labour, for Walling of random rubble stone masonry (Bangalore type), brought up to courses, well bonded, bedded and solidly hearted, built in CM(1:6), but except stone complete all as specified and directed. NOTE :- Serviceable stones obtained from Sl item No 1 shall be reused in the work.

Hacking out old broken glass of any thickness, size, quality or description from metal frame including punching or drilling out old glazing pins/spring clips etc providing material and labour for 4 mm thick figured glass, pin head type and glazing with oil putty in squares not exceeding 0.5 Sq m in each pane including provision of necessary scaffolding and staging externally for working up to four storied bldg all as specified and as directed.

Hacking out old broken glass of any thickness, size, quality or description from metal frame including punching or drilling out old glazing pins/spring clips etc providing material and labour for 4 mm thick Sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5 sq m in each pane including necessary scaffolding and staging externally for up to four storied bldg all as specified and as directed.

Supply and fix in repairs, stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.18 mm, fixed with mild steel screw & bolts all as specified and as directed.

Taking down tubular curtain rod, supply and fixing drapery rod, decorative type, made of 25 mm dia stainless steel (wall thickness not less than 0.63 mm), wood finish, colour and pattern as approved by GE, complete all as specified and as directed. (Note : Price shall not be less than 100/- per RM)

Taking down old unserviceable rod/rail, Supply and fix stainless steel type brackets suitable to hold the curtain rod with sofio phenol (Lotto) and wooden round blocks for curtain rod of 20mm dia, decorative type fixed with steel screws and PVC cleats complete all as specified and as directed.

Supply and fixed in repairs Aluminium anodized barrel towel bolts of extruded section of length 150 mm all as specified and as directed.

Supply and fixed in repairs Aluminium anodized barrel towel bolts of extruded section of length 200 mm all as specified and as directed.

Supply and fix in repairs 100mm Aluminium anodized barrel tower bolts of extruded section complete all as specified

Supply and fix in repairs Aluminium alloy anodized sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections including taking down old sliding door bolt 300 mm all as specified and as directed.

Supply and fix in repairs Extruded alloy handles fabricated type anodized of size 100 mm all as specified and as directed.

Supply and fix in repairs Extruded alloy handles fabricated type anodized of size 150 mm all as specified and as directed.

Supply and fix in repairs Butt hinges medium weight cold rolled mild steel of size of hinges 100mm all as specified and as directed.

Supply and fix in repairs Hasp and staple safety type of size 100 mm of aluminium anodized all as specified and as directed.

Supply and fix in repairs, 100 mm size Mortice rim lock (4 lever), vertical type, brushed steel suitable for 25 to 40 mm thick doors screwing complete all as specified and as directed.

Supply and fix in repairs 40 mm dia cupboard knobs fixed with nut, screw and washer of Brass, polished complete all as specified and as directed.

Supply and fix in repairs 150 mm floor door stopper of aluminium alloy powder coated, with hard down steel spring all as specified and as directed.

Supply and fix in repairs, door closer hydraulically regulated designation No.3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg of aluminium (Die cast body) complete all as specified and as directed.

Supply and fix in repairs mild steel 300mm, ordinary rat tail rod pattern spring hinges, including roller and roller plate complete

Supply and fix in repairs, Magnetic ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and as directed.

Taking down unserviceable boards as in shelves of cupboards, doors, etc., supply and fix 18/19 mm thick pre-laminated particle board, Grade 1 quality, interior grade, with decorative face veneers on one side and other side balancing white, fixed with screws / nails to timber framework and fixed in shutters / shelves, complete all as specified and as directed.

Material and labour for, second class hardwood, plain fillets square, rectangular or triangular in section clean sawn, secured with nails or brads, fixed to cupboard shutter, cross sectional area not exceeding 3 sq cm all as specified and directed.

Taking down old sinks and Supply and fixing Stainless steel sink with draining board, made out of 1.00 mm thick sheet for kitchen over all size 915 mm x 460 mm with bowl size 405 x 355 x 178 mm all as per Cat No.SSSBSD-52 of Blue Star make or techno commercially equivalent in other makes specified including CP waste coupling of 40 mm dia, cast iron cantilever brackets, 40 mm dia 800 mm long corrugated PVC waste pipe, washers, connecting union etc including bedding in cement mortar on to dwarf wall or fixing on granite slab. complete all as specified and directed.

Taking down old sinks and Supply and fixing Stainless steel sink without draining board, made out of 1.00 mm thick sheet for kitchen over all size 495mm x 420mm with bowl size 405 x 355 x 178 mm all as per Cat No.SSSB06A of Blue Star make or techno commercially equivalent in other makes specified including CP waste coupling of 40 mm dia, cast iron cantilever brackets, 40 mm dia 800 mm long corrugated PVC waste pipe, washers, connecting union etc in cement mortar on to dwarf wall or fixing on granite slab. complete all as specified and directed.

Taking down unserviceable plate rack, supply and fix new Stainless steel plate rack of 0.63mm thick sheet, size 600mm x 750mm and of weight not less than 4.5kg each complete all as specified and directed. Make: Blue star, Model No. SSKPR-311.or techno-commercially equivalent make specified here-in-after.

Supply and fix in repairs, Vitreous china snow white, wash hand basin of size 550 mm x 400 mm excluding chain and plug and porcelain stopper including brackets, supply and fixing of 32 mm dia, PVC corrugated / flexible waste pipe, 800 mm long and with brass waste coupling of 32 mm dia, complete all as specified and as directed. Make : CERA, Cat No S2040103 or techno commercial equivalent in other makes, complete all as specified and as directed.

Supply and fix in repairs, Vitreous china, white colour, water closet pan (pedestal pattern), with PP soft seat cover, hinges, other fixing accessories set (excluding flushing cistern and flush pipe), UPVC (SWR), 'P' or 'S' trap, and connecting to drain (or outgoing pipe), flush pipe, anti syphonic pipes and removing debris outside MD land. Make : Cat Part No S1050101 of Cera or techno commercial equivalent in other makes complete all as specified and as directed.

Supply and fix in repairs, Vitreous china, white colour, 'Orissa pattern' squatting pan of size 580 mm x 440 mm with UPVC 'P' trap or 'S" Trap, front or back inlet, integral foot rests, connecting to trap, flushing pipe, anti syphonic pipe, including making good to floor removing debris outside MD land, complete, all as per Make : Cera, Cat No S3010102 of CALINA make or techno commercially equivalent in other makes specified here-in-after.

Supply and fix in repairs, PVC valve less, syphonic action type, flushing cistern, Duo Flush cistern 10 ltr capacity, low level, white, with inlet, ball valve, float and handle including brackets, connections to pipes and fixing of chain and pull, or lever, complete all as specified and directed. (Cat No-502 of Prayag or equivalent in any approved make as in CA)

Taking down unserviceable GI tubing, supply and fixing new CPVC pipes, outer dia 20 mm, SDR 11 Plain with all fittings, such as Tee, elbows, sockets, unions, short pieces and application of bituminous paint in concealed portion, fixed to wall/ ceiling or laid on floors, complete all as specified and as directed. Notes: Serviceable Taps, valves in any shall be removed before taking down pipe and same shall be re-fixed while providing new pipe.

All as per Serial Item No 1.055 here-in-above, but of outer dia 25 mm dia

Taking down unserviceable GI tubing, supply and fixing new 20 mm bore Galvanized Iron tubing, medium grade, with all fittings, such as Tee, elbows, sockets, unions, short pieces and application of bituminous paint in concealed portion, fixed to wall/ ceiling or laid on floors, complete all as specified and as directed. Notes: Serviceable Taps, valves in any shall be removed before taking down pipe and same shall be re-fixed while providing new pipe.

All as per Serial Item No 1.057 here-in-above, but of outer dia 25 mm dia

Supply and fix in repairs, Brass CP wall mixer for mixing hot and cold water screwed down for iron pipe, with provision for overhead shower, fixed complete all as specified and directed (Cat No-PIS-75H of Neptune series of Prayag or equivalent make as specified here-in-after)

Supply and fix in repairs, 15 mm Centre hole Basin mixture W/o Pop Up all as specified and as directed.(Cat No PIS-50 H Neptune series of Prayag or equivalent make as specified here-in-after.

Supply and fix in repairs, 15 mm pillar taps swan neck type, chromium plated cast copper alloy fancy type complete all as specified and as directed.(Cat No PIS-14H Neptune series of Prayag or equivalent make as specified here-in-after)

Supply and fix in repairs, 100mm (4") overhead shower ABS with brass Arm (225mm) & flange including fixing to steel pipe or union complete all as specified and as directed. (Cat No BS-73 Neptune series of Prayag or equivalent make as specified here-in-after).

Supply and fix in repairs, 15 mm angle cock CP cast copper alloy screwed down high pressure with capstan head handle screwed both ends or for unions etc . (Cat No PIS-10H Neptune series of Prayag or equivalent make as specified here-in-after)

Supply and fix in repairs, Bib Cock 2-way double handle with CP flange all as specified and as directed. (Cat No-PIS-12H Neptune series of Prayag or equivalent make as specified here-in-after).

Supply and fix in repairs, Chromium plated long body bib tap 15mm dia with CP flange all as specified and as directed. (Cat No-PIS-08H Neptune series of Prayag or equivalent make as specified here-in-after).

Supply and fix in repairs, Chromium plated bib tap 15mm dia with CP flange all as specified and as directed. (Cat No-PIS-06H Neptune series of Prayag or equivalent make as specified here-in-after).

Supply and fix in repairs, Health faucet, brass body with 1mtr SS braided tube & wall hook complete all as specified and as directed (Cat No-BEA-41/BEA-85 of Prayag or equivalent make as specified here-in-after)

Supply and fix in repairs, Towel rail stainless steel glossy finish 20 mm dia and 600 mm long complete all as specified and as directed. (Cat No-BA10S of prayag or equivalent make as specified here-in-after)

Supply and fix in repairs, Towel rack Brass glossy finish complete all as specified and directed (Cat No BA-03 of Prayag or equivalent make as specified here-in-after)

Supply and fix in repairs Towel ring Brass glossy finish complete all as specified and directed (Cat No BA-02 of Prayag or equivalent make as specified here-in-after)

Supply and fix in repairs Soap dish chromium plated brass all as per Cat Part No BA-45 of Prayag or equivalent makes fixed in wall as per manufacturers instruction.

Supply and fix in repairs Mirror 600x450 x 5-6mm thick with frame cat No BLM-01F of PRAYAG or equivalent make complete all as specified and directed

Supply and fix in repairs PVC Mirror cabinet of size 400x500 mm (Cat No 554 of Prayag or equivalent make) complete all as specified and as directed.

Supply and fix in repairs Unbreakable (Square) wall mounted shelf 500mm (Cat No BEA-47A of Prayag or equivalent make as specified here-in-after) complete all as specified and directed

Supply and fix in repairs Unbreakable corner shelf (3Pcs set i.e, 8"-1, 10"-1 & 12"-1) (Cat No BEA-44A of Prayag or equivalent make as specified here-in-after) complete all as specified and directed

Supply and fix in repairs peg set of six (Cat No BEA 30 of Prayag or equivalent make of CA) fixed in wall as per manufacturers instruction

Supply and fix in repairs Toilet paper holder (Cat No BA-88 of Prayag or equivalent make of CA) fixed in wall as per manufacturers instructions all as specified and as directed.

Supply and fix in repairs PVC connection (Suitable for Cold Water Supply) 15 mm size with PTMT nuts of length 450 mm, all as specified and as directed.

Supply and fix in repairs PVC connection (Suitable for HOT Water Supply) 15 mm size with PTMT nuts of length 450 mm, all as specified and as directed.

Supply and fix in repairs, 32 mm dia waste fittings, brass, chromium plated for sinks, basins, etc with long screwed shanks and fly nuts, flange end complete all as specified and as directed

Supply and fix in repairs, 75 mm dia waste fittings ,brass, chromium plated for sinks etc with long screwed shanks and flynuts, flange end fixed in repair complete all as specified and as directed.

Supply and fix in repairs, 32mm dia, 800mm long PVC corrugated waste pipe complete all as specified and as directed.

Supply and fix in repairs PVC urinal waste pipe 32mm dia 800mm long, complete all as specified and directed

Dismantling of unserviceable floor trap, supply and fix PVC(SWR) floor trap 75 mm dia outlet with CP grating, including jointing with solvent cement complete all as specified and as directed.

Supply and fix in repairs grating doom 100 mm dia of PTMT (Minimum weight 25 grams) complete all as specified and as directed

Supply and fix in repairs Health faucet, with 8 mm dia, 1.2 m long, flexible tube in PVC body, wall hook with NRV (back flow preventer), all as per Cat Part No ALD-577 of Jaguar or techno commercial equivalent in other makes complete all as specified and directed.

Supply and fix in repairs 15mm dia Bib tap (Minimum weight 15mm-120gms), long body, PTMT fancy type any colour screwed, for iron pipe and fixed complete all as specified and as directed.

Supply and fix in repairs 15mm dia Pillar tap PTMT fancy type (Minimum weight 15mm-120gms), any colour screwed, for iron pipe and fixed complete all as specified and as directed

Supply and fix in repairs 15mm dia angle stop valve of PTMT (Minimum weight 15mm-90gms), any colour pressed screwed, for iron pipe and fixed complete all as specified and as directed

Supply and fix in repairs, PVC water tank covers suitable for water tanks of capacity 500 / 1000 / 2000 litres complete all as specified and as directed

Supply and fixing in repairs, EWC seat covers, white closed pattern with recessed bottom, including screws and connectors complete all as per Cat Part No B1510101 of CERA Make or equivalent in other makes, removing debris outside MD land, complete all as specified and directed.

Carrying out Petty repairs to arrest leaking of water in bib taps, pillar taps, stop cock, angle valve, PVC connection waste pipes, float valves, concealed stop cock. GI pipe joints bottle traps etc of any description by changing the washers or any other minor accessories to make the system functional complete all as specified and directed.

Carrying out Petty repairs to high/low level flushing cistern by adjusting the float valve, leakage of PVC connection, PVC/GI bend replacing of rubber washer check nuts plugs etc for any type of flushing cistern complete all as specified and directed.

Dismantling of water tanks of 500 litres capacity from roof top and supply and fixing Rotational moulded polyethylene water storage tanks (double layered) of 500 Litres capacity with ISI mark embossed on it, (cylindrical, vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

All as per Serial Item No 1.094 here-in-above, disconnecting water tank of capacity 500 litres and setting aside for carrying out repairs and re-fixing disconnected tank.

Dismantling of water tanks of 1000 litres capacity from roof top and supply and fixing Rotational moulded polyethylene water storage tanks (double layered) of 1000 Litres capacity with ISI mark embossed on it, (cylindrical, vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

All as per Serial Item No 1.096 here-in-above, disconnecting water tank of capacity 1000 litres and setting aside for carrying out repairs and but re-fixing disconnected tank after carrying out repair works.

Supply and fix in repairs, 20 mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 210 grams) complete all as specified and as directed.

Supply and fix in repairs, 25 mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 455 grams) complete all as specified and as directed.

Supply and fix in repairs, gun metal, globe or gate valves 20 mm bore (ISI marked) with iron wheel head screwed both ends for iron pipe complete all as specified and as directed.

Supply and fix in repairs, gun metal, globe or gate valves 25 mm bore (ISI marked) with iron wheel head screwed both ends for iron pipe complete all as specified and as directed.

Material and labour, for UPVC pipes (conforming to IS 15328) of 160 mm internal dia, foam core, self fit, 0.4 M pa (class 2) with pressure rating @ 4 Kg / Sq cm, laid in trenches including bends, elbows, etc., complete all as specified and as directed.

Material and labour, for UPVC pipes (conforming to IS 15328) of 200 mm internal dia, foam core, self fit, 0.4 M pa (class 2) with pressure rating @ 4 Kg / Sq cm, laid in trenches, including bends, elbows, etc., complete all as specified and as directed.

Material and labour, for Reinforced concrete pipes, class NP3, 150 mm dia bore of pipe laid and jointed complete with collars complete all as specified and directed by Engr-in-charge

Material and labour, for Reinforced concrete pipes, class NP3, 200 mm dia bore of pipe laid and jointed complete with collars complete all as specified and directed by Engr-in-charge

Material and labour, for Reinforced concrete pipes, class NP3, 300 mm dia bore of pipe laid and jointed complete with collars complete all as specified and directed by Engr-in-charge

Material and labour for, brick work, with subclass 'B' bricks straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and as directed

Material and labour for, brick work, with serviceable bricks obtained form demolition, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and as directed

Material and labour for, 25 mm thick, Plain Cement concrete type B0 1:2:4 (12.5 mm graded aggregate) as in floorings, with surfaces, finished even and fair complete all as specified and as directed

Demolition of floor, hearth or wall tiling including cement mortar bedding (including backing), removing rubbish off the premises and disposing outside MD land and providing Material and labour, for non-skid Ceramic coloured tiles 7 to 8 mm thick (Grade B-IIA), area of each tile exceeding 0.06 sq m but not exceeding 0.11 sq m, as in flooring, set and pointed in white or coloured cement to match colour of tiles over and including 15 mm thick screed bed in CM (1:6) complete all as specified and as directed.

Demolition of floor, hearth or wall tiling including cement mortar bedding (including backing), removing rubbish off the premises and disposing outside MD land and providing Material and labour, for coloured Glazed ceramic printed tiles, of size 450 x 300 x 7 mm thick (Grade B-IIA) as in vertical surfaces such as skirting, dado etc., set and jointed in neat cement slurry and pointed in epoxy grout to match with the colour of tiles, laid over and including provision of backing coat of 10 mm thick rendering in CM 1:3, complete all as specified and directed.

Material and labour for Plain cement concrete, 75 mm thick, type D- 2, 1:4:8 (40mm graded aggregate) as in sub base of flooring, flooring etc complete all as specified and as directed

Material and labour for, rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished plastered surface even and smooth without using extra cement complete all as specified and as directed

Material and labour for, rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished plastered surface even and smooth without using extra cement complete all as specified and as directed

Material and labour for, rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:4 with WPC, finished plastered surface even and smooth without using extra cement complete all as specified and as directed. Note :- Supply only WPC will be measured and paid separately

Supply only water proofing liquid complete all as specified and as directed

Material and labour for, rendering 5 mm thick on ceiling / RCC surfaces in cement mortar 1:3, finished plastered surface even and smooth without using extra cement complete all as specified and as directed.

Material and labour for, keyed pointing to random or polygonal rubble, un-coursed or brought up to courses in Cement Mortar 1:4, complete all as specified and as directed.

Raking to random rubble or polygonal rubble un-coursed or brought up to courses providing Material and labour for, keyed pointing to random or polygonal rubble, un-coursed or brought up to courses in Cement Mortar 1:4, complete all as specified and as directed.

Preparation of newly plastered surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer over and including 1 mm thick wall care putty, complete all as specified and as directed. Note : Quoted rate shall deemed to include for cost of wall care putty.

Preparation of newly plastered surfaces of wall and applying two coats of cement base paint complete all as specified and as directed.

Preparing newly plastered ceiling surfaces and applying three coat of white wash complete all as specified & as directed.

Material and labour for cleaning of PVC/RCC over head water tanks at any height (on accessible/inaccessible roofs) by removing all scale, dirt, mud, any foreign material, accumulated silt, other dirty substance, algae, fungus and any other bacterial material from sides/bottom of tank, cleaning shall be done by draining / pumping out water / sludge from bottom, by high pressure water jet of pressure not less than 120 PSI for removing clogged mud/scales etc and cleaning the same again with self priming pumped fresh water and disinfecting the water tank by using UV radiator and approved chemical (chlorite), after cleaning writing letter / figures (Date of cleaning and next Date of cleaning) on black back ground with white synthetic enamel paint including removing the existing letters/ figures complete all as specified and as directed for water tanks of capacity exceeding 250 litres and not exceeding 500 litres complete all as specified and as directed.

All as per Serial Item No 1.123, but for water tanks of capacity exceeding 500 litre and not exceeding 1000 ltr.

All as per Serial Item No 1.123, but for water tanks of capacity exceeding 1000 litre and not exceeding 2000 ltr. Note for Sl Item Nos 1.123 to 1.125 :: (i) Contractor shall ensure that no damages / leakage occur in tank after cleaning . (ii) Any air lock /blockage of water flow after cleaning will be made good immediately.

Material and labour for spraying anti weed / non toxic solution / chemicals containing Glyphosate as per manufacture instructions and removing the weed including the roots after ensuring complete de-germification of plant/weed and cutting down the plant/trees off from roof/top sides of external walls of bldgs, in chajjas, wall junctions, junctions of GI/CI/AC/PVC pipes and taking out roots entered in wall/slabs, including making good the surface using PCC 1:2:4 type B1 or cement mortar (1:2) or brick work in CM(1:4) plastered with CM(1:4) to match with existing surface and repairing the pipes and joints which was affected by cutting down/taking out process all as specified and as directed for plants / trees located in the buildings up to four storey high, complete all as specified and directed by Engineer-in-charge. NOTE:- Contractor has to execute the work of de-generated plant/weeds as per the prior approval and directions of Engineer-in-charge.

All As per item no 1.126 here in before but plants located in the buildings of five to eight storey high.

Material and labour for cleaning of Roof (Area of Roof up to 500sqm) at height of (on accessible roof height not exceeding 30RM /inaccessible roofs height not exceeding 10RM) by removing all scale, dirt, mud, any foreign material, accumulated silt, other dirty substance, algae, fungus, leaves etc deposited over slab and making good the disturbed surfaces to match with existing surface and removing the material so obtained out side complete all as specified and directed by Engineer-in-charge. NOTE:- Contractor has to submit the photographic record of work done (before and after the work done duly annoted the Building No/Location) at the time of claiming the payment (RAR/Final Bill). No payment has to be made without submit the photographic records.

All as per Serial Item No 1.128 here-in-above, but roof area exceeding 500 Sq m each.

Removal of sludge from manholes of any size and depth and burying the sludge in pits with suitable depth & filled by earth and removal of surplus soil including dewatering of water complete all as directed to a place as earmarked by state auth out side the defence land . Note - Dewatering of water or mud will not be paid only sludge removed shall be considered for payment.

Clearing & removal of blockage, of any type in WC, bathroom, kitchen including floor/ nahani traps, soil waste/vent pipes gully trap up to 1st manhole, in any situation by way of cleaning / de-sludging and removing foreign materials to a place as earmarked by state authorities out side the defence land to the entire satisfaction of Engineer-in-charge.

Mechanically pumping out sewage liquid from septic tanks/ manholes of any size and depth and removal the same to distance/place as earmarked by state authorities out side defence land including any type of T & P required etc. dewatering of water complete all as directed.

Taking down eaves gutters, soil / waste / vent pipes / rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., Supply and fix, PVC (SWR) pipes 75mm dia, type B (Conforming to IS 13592), single socketed in any length with solvent cement joints laid under floor or on walls fixed as soil / waste / vent pipes with Stack clamps made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall complete all as specified and as directed.

All as per Serial Item No 1.133 here-in-above, but for 110 mm dia pipe.

Supply and fix in repairs, 75mm dia PVC (SWR) Bends, with access door of any radius .

All as per Serial Item No 1.135 here-in-above, but for 110 mm dia pipe.

Supply and fix in repairs, 75mm dia PVC (SWR) junction single (single T) equal or unequal with access door

All as per Serial Item No 1.137 here-in-above, but for 110 mm dia pipe.

Supply and fix in repairs, 110 mm dia PVC(SWR) branch piece, single(single Y) equal or un equal with access door.

All as per Serial Item No 1.139 here-in-above, but for 110 mm dia pipe.

Supply and fix in repairs, 75 mm dia PVC (SWR) branch piece, (double Y) equal or unequal with access door

All as per Serial Item No 1.141 here-in-above, but for 110 mm dia pipe.

Supply and fix in repairs, 75mm dia PVC (SWR) vent cowl.

All as per Serial Item No 1.143 here-in-above, but for 110 mm dia pipe.

Taking out carefully, cover slabs of man holes of any size and shape, removing scum/sludge including any organic or inorganic matters to a distance exceeding 50m and not exceeding 1500m and depositing eco friendly where as directed by Engineer-in-Charge, setting back the man hole cover in position with CM (1:6 ) for manhole of depth up to 1.5 m Note: Manhole cover if required to provide new shall be measured & paid separately under respective items.

All as per Serial Item No 1.145 here-in-above, but for manholes of depth exceeding 1.5 m and not exceeding 3 m

All as per Serial Item No 1.145 here-in-above, but for manholes of depth exceeding 3.0 m and not exceeding 4.0 m

Clearing & removal of all blockage in sewage line of internal dia of 100 mm, from manhole to manhole of length not exceeding 20 mtr, of any dia of sewer lines, manholes of any section and any depth, in any situation by way of cleaning / de-sludging foreign materials as well as blockage of sewage line in between successive manholes manually / mechanically including de-sludging of manhole /sewage line where required and ordered by Engineer-in-charge and keeping sewer line functional, up to final drop/outlet into septic tank /central sewage system terminating in other joining zone/ area or into sewage wells including removing the sludge / mud to a distance exc. 50m and not exceeding 1500 m and depositing eco friendly complete all as specified. Note:- (a) Contractor shall detail his supervisor to office of AGE B/R (North) daily by 9.00 AM who will report to concerned JE B/R /Engineer-in-Charge to receive all complaints of entire area under this contract. Contd/-- 1.148

Contd/-- 1.148 (b) Contractor shall provide service providers (sweepers) at complaint cell located at respective AOR, attend to complaints as per the complaints register including providing all requisite tools, equipments, safely measures for attending complaint and ensuring completion report by 5 PM on same day. (c) All the complaints relating to sewage line shall be attended on same day. In case blockage in sewage line could not be detected/completed on same day and, concerned JE / Engineer-in-Charge is satisfied to the efforts taken to clear blockage, the same shall be cleared by next day without fail. (d) In case any complaint pertaining to clearing of blockage in sewage line is not removed /cleared within 24 hours (next day 5.00 PM), a penalty @ Rs. 200/- per complaint shall be levied in contractor payments. (e) Blockage cleared between two man holes irrespective of length in between shall be treated as one complaint.

All as per Serial Item No 1.148 here-in-above, but for sewer line of internal dia 150 mm

All as per Serial Item No 1.148 here-in-above, but for sewer line of internal dia 200 mm

All as per Serial Item No 1.148 here-in-above, but for sewer line of internal dia 200 mm

Material and labour for, Pre-cast Reinforced Cement Concrete, (1:2:4), type B1 using 20 mm graded stone aggregates as in cover slabs of manholes, gully traps, drains, etc., set in CM(1:4) complete all as specified and as directed. NOTE :- Steel for Reinforcement will be measured and paid separately.

Material and labour for, Mild steel TMT bars of 10 mm dia as in reinforcement, cut to length, bent to shape required, including cranking, bending, spirally looping for columns, hooking ends & binding with and including mild steel annealed wire of not less than 0.9 mm dia or securing with clips complete all as specified

Material and labour for, mild steel TMT bars of 6 to 8 mm dia as in reinforcements, cut to length , bent to shape required, including cranking, bending, spirally looping for columns, hooking ends & binding with and including mild steel annealed wire of not less than 0.9 mm dia or securing with clips complete all as specified

Supply and fabrication of mild steel structural work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Grade E-165 complete all as specified and as directed.

Material and labour for, mild steel screw bolts (Machine made, dia of neck 10mm) with hexagonal or square heads at one end and screwed the other, or screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut not exceeding 5cm long etc complete all as specified and as directed.

Supply and fabrication of steel as in framed work such as grills, gratings, ladders, balusters, walk ways, railing, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and as directed.

Taking down existing chain link fencing, and fixing new only chain link fencing incl line, wire any mesh, size and type to any type of standards, rails, straining bolts, etc including provision of binding wire etc complete all as specified and as directed. Note: Supply only chain link fencing of any section will be measured and paid for separately under respective item.

Supply only chain link fencing any size or type etc complete all as specified and as directed

Taking down old concertina coil and Supply and fixing Galvanized punched type Concertina Coil with 80 spiral turns in each 9 m of recommended stretched (laid) length & 600 mm effective dia (after laying) with central core wire high tensile galvanized spring core wire (HTGS) made up of 2.6 mm dia as per IS: 4454, Part-1, Grade-II having minimum galvanizing of 230 – 250 grams per sq m, with a tape of razor sharp barbs strip of 0.5 mm thick and 19 mm width conforming to IS: 513 DD, barbs punched along the length at regular interval of 120 barbs per running meter, crimped with 4 to 5 Nos. of clips per each spire made up of Stainless Steel (SS-304) including fixing of concertina coil on support fixed through out the compound wall with the help of required u-nails / split pin, scaffolding etc; complete all as specified and as directed by the Engineer-in-Charge.

Taking down old barbed wire and Supply and fixing Galvanized. 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanized mild steel wire, staples or steel pins, etc ., complete all as specified and as directed Note :- Each line wire to be measured

Taking down old glass coping providing Material and labour for, broken glass copings with 25 mm thick rendering in CM (1:3) with rounded or weathered finish, using broken glass of bottle or thick glass of 63 mm thick gauge embedded firmly in the mortar @ 4 Kg of glass per Sq m of rendering surfaces keeping jogged edges of the glass projecting on top of compound wall incl complete all as specified and directed

Material and labour, for Preparation of new or previously untreated plastered wall surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of cement base paint over a coat of alkali resistant primer , complete all as specified and as directed.

Material and labour, for preparation of new or previously untreated steel surfaces of any description not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

Material and labour, for preparation of old plastered surfaces and applying one coat of synthetic enamel paint, complete all as specified and as directed.

Preparation of old treated plastered or un-plastered wall surfaces of any description including brooming down with steel wire brushing scrapping down smoke soot’s, moulds, moss and efflorescence, salts, trading oil and greasy spots etc and applying one coat of white wash on wall surfaces all as specified and as directed.

Preparation of old treated plastered or un-plastered wall surfaces of any description including brooming down with steel wire brushing scrapping down smoke soot’s, moulds, moss and efflorescence, salts, trading oil and greasy spots etc and applying two coats of white wash on wall surfaces all as specified and as directed.

Demolition of stone slabs and tiles of any description and providing Material and labour for providing, exterior grade, coloured glossy finish rubber pressed, cement concrete designer chequered tiles of size 30cm x 30cm x 25mm thick set, jointed and pointed in neat cement slurry with grey cement and pigment to match the shade / colour / matrix of tiles as in floor, over and including cement screed bed of 15 mm thick in CM 1:6. complete all as specified and as directed

Demolishing paver block tiles, and providing material and labour for, Rubber moulded pressed precast concrete interlocking paver block of any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and no pigments, laid over and including 50 mm thick sand cushioning complete all as specified and as directed.

Material and labour for, Rubber moulded pre-cast Kerb stones of cement concrete 1:2:4 (20 mm graded stone aggregates) factory made, size, shape, pattern and finished as approved, including rounding, chamfered or half round and bedded of perfectly leveled surface pointed and jointed in CM 1:4 etc complete all as specified and as directed

Eeguchi Constructions

Chaitanya Constructions

SP ENTERPRISES

H S S ENGINEERS AND CONTRACTORS