CERTAIN REPAIRS TO ROOFING, JOINERY, PALSTERING, FLOORING, ETC OTHER MISC B/R AND E/M WORK AT WEU AIR FORCE STATION SRINAGAR

Amount

Demolition of cement concrete unreinforced in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed by Engineer-in-Charge

Demolition of brickwork or stone/boulder masonry, build in cement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articles complete all as specified and directed by Engineer-in-Charge

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Dismantling boarding any description fixed in any position with nails, complete all as specified and directed by Engineer-in-Charge.

Dismantling of plain or corrugated steel sheeting any gauge in roof coverings complete all as specified and directed by Engineer-in-Charge

Taking down Chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 sqm but n exc 4 Sqm each and credited to the contractor all as specified and directed by Engineer-in-Charge

Taking down Chowkats or frames with shutters (without taking off shutters from the frames) n exc. 1.5 sqm and credited to the contractor all as specified and directed by Engineer-in-Charge

M &L for Galvanised, corrugated MS sheeting, 0.63 mm thick with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of Zinc coating 275, complete all as specified and directed by Engineer-in-Charge

M &L for Plain, galvanised, mild steel sheeting 0.80mm thick, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 fixed with self tapping screws, Complete all as specified and directed by Engineer-in-Charge

M&L for tightening bolts and closing bolt holes, etc.to rectify the leakage/ seepage, in old roof of corrugated steel sheets by sealing with one bitumen and one curved GI washer on either side and 6mm G.I. bolts and nuts if required, all set in stiff white lead Complete all as specified and directed by Engineer-in-Charge.

M & L for plywood, grade BWR, type BB, 6mm thick fixed with screws to timber framework as in ceiling flat or sloping complete all as specified and directed by Engr-in-Charge.

M & L for plywood, grade BWR, type BB, 12mm thick fixed with screws to timber framework as in partition walls complete all as specified and directed by Engr-in-Charge.

M & L for weather boarding, second class hard wood clean sawn,20mm thick and wrought both side,feather edged 15-20mm thick to give 20mm laps and fixed as in eaves board etc complete all as specified and directed by Engineer-in-Charge.

M & L for second class hardwood fillets bullnosed, splayed, chamfered or rounded on one edge or face of exc 13 Sqcm but not exc 25 sqcm in repairs, secured with nails or screws in repairs , complete all as specified and directed by Engineer-in-Charge.

M & L for second class hardwood plain fillets, square or rectangular or triangular in section clean sawn exc 6 Sqcm but not exc 13 sqcm in repairs, secured with nails or screws in repairs , complete all as specified and directed by Engineer-in-Charge.

M & L for Plain, solid, straight, chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, in second class hardwood all as specified and directed by Engineer-in-Charge.

M & L for Plain, framed, panelled shutters (any number of panels), 35mm thick with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers; in second class hardwood, Complete all as specified and directed by Engineer-in-Charge.

M & L for Glazed and skeleton shutters 30mm thick, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24; in second class hardwood, Complete all as specified and directed by Engineer-in-Charge.

S&F in repair galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinned tack or galvanised wire staples complete all as specified and directed by Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden or metal frames glazed with putty or fixed with beads complete all as specified and directed by Engineer-in-Charge.

M&L for sheet glass 3mm thick, ordinary quality and glazing with oil putty in square n exc 0.5 sq.m in each pane, in repairs, complete all as specified and directed by Engineer-in-Charge.

M&L for Aluminium, anodised, barrel tower bolts 150mm size of extruded section, complete all as specified and directed by Engineer-in-Charge.

M&L for Aluminium alloy, anodised, sliding door bolt 300mm length with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed by Engineer-in-Charge

M&L for But hinges, medium weight, cold rolled mild steel 100mm size, complete all as specified and directed by Engineer-in-Charge

M&L for Aluminium handles, cast type, anodised 150mm size complete all as specified and directed by Engineer-in-Charge

S & F in repairs, Mild Steel ordinary rat tail rod pattern springs including roller and roller plate complete 300mm length, complete all as specified and directed by Engineer-in-Charge

M & L for Synthetic enamel paint two coats over a coat of pink primer on wood and wooden based surfaces of any description exc 10cm width or girth including preparation of previouly untreated surfaces, complete all as specified and directed by Engineer-in-Charge

M & L for Anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified and directed by Engineer-in-Charge.

M & L for Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.) hinge type B-21 100mm long (2 no.) suitable handle (1 no.), complete all as specified and directed by Engineer-in-Charge.

M & L for Anodised aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by Engineer-in-Charge.

M&L for sheet glass 5.5mm thick, ordinary quality and glazing with aluminium glazing clips and rubber neosprine gasket in square or rectangular, complete all as specified and directed by Engineer-in-Charge.

M&L for aluminium door/window including necessary jointing clips, rubber gasket, glazing clips, aluminium hinges etc as required and as directed by Engineer-in-Charge.

S&F in repair for mortice lock, vertical type, size 75mm 4 lever aluminium body for aluminium door complete all as specified and directed by Engineer-in-Charge

S&F in repair for door closer aluminium (extruded body) hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed complete all as specified and directed by Engineer-in-Charge

M & L for Cement concrete type C-2, 1:4:8 (40mm graded aggregate) as sub base, 75mm thick complete all as specified and directed by Engineer-in-Charge

M&L for 75mm thick plain cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection/path/hard standing finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M & L for rendering 10 mm thick in CM 1:4 as for backing coat of wall tiles, complete all as specified and directed by Engineer-in-Charge

M & L for screed bed or bedding layer 15mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and as directed by Engineer-in-Charge.

M & L for Non skid straight edge ceramic tiles joint free 7 to 8mm thick (square/rectangular) area of each tile not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and directed by Engineer-in-Charge.

M & L for glazed ceramic (digital glossy finish) coloured tiles joint free area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm on vertical surfaces, set and jointed in neat cement slurry and pointed in white/colour cement to match over, Complete all as specified and directed by Engineer-in-Charge.

M & L for double charged Vetrified coloured tiles 7-10mm thick (Square/ Rectangular) polished area of each tile not exceeding 0.36 Sqm in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engineer-in-Charge.

All as per serial Item No. 41above but as in skirting/dado etc over and including 10mm thick cement mortar backing in cement mortar 1:4 with cement slurry complete all as specified and directed by Engineer-in-Charge.

S & F in repair to urinal sensors including all necessary fittings and fixture complete to make smooth functioning of sensor urinals, complete all as specified and directed by Engineer-in-Charge.

M & L for mild steel Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0, as in repairs, complete all as specified and directed by Engineer-in-Charge.

M & L for Brick work with sub class `B' bricks straight or curved on plan exc 6m mean radius with old size bricks built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge

Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed by Engineer-in-Charge.

M&L Rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces and finishing even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L Rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces and finishing even and smooth without using extra cement with water proofing compound complete all as specified and directed by Engineer-in-Charge. Note: (WPC will be measured and paid separately)

M&L Rendering 10mm thick in CM 1:3 on fair faces of concrete surfaces of ceiling and finishing even compound complete all as specified and directed by Engineer-in-Charge.

Supply only Polymer liquid water proofing compound of make Pidilite/Bauchemic/Fosrock, all as specified and directed.

M & L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash on ceiling , complete all as specified and directed by Engineer-in-Charge

M & L for preparation of newly plastered surfaces of ceiling and applying two coats of distemper oil emulsion paint colour tint as ordered in any pattern complete all as specified and directed by Engineer-in-Charge

M & L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint colour tint as ordered in any pattern complete all as specified and directed by Engineer-in-Charge

M & L for preparation of new or previously untreated steel surfaces of steel of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamal paint over a coat of red oxide primer including treating with modrant solution complete all as specified and directed by Engineer-in-Charge

M&L for preparation of old or previously untreated steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying one coats of synthetic enamal paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel water tubing and connection complete 15 mm bore complete all as specified and directed by Engineer-in-Charge

Taking up or down steel water tubing and connection complete 20 mm bore, complete all as specified and directed by Engineer-in-Charge.

S & F GI tubes 15 mm bore 'medimum grade' with all fittings and fixed complete to walls and ceilings or laid in floors or cutting chases in wall and making good to disturbed portion of wall complete all as specified and directed by Engineer-in-Charge.

S & F GI tubes 20 mm bore 'medimum grade' with all fittings and fixed complete to walls and ceilings or laid in floors or cutting chases in wall and making good to disturbed portion of wall complete all as specified and directed by Engineer-in-Charge.

M & L for Lagging to pipes 20mm bore used in external water supply or plumbing all around with 25mm thick bonded mineral wool pre-formed ‘SNAP ON’ pipe sections of density 144 Kg /Cum conforming to IS 9842 provided with chicken mesh wire netting 25mm gauge 20mm mesh complete all as specified and directed by Engineer-in-Charge

S&F in repairs vitreous china ware wash hand basin white flat back, size 630x450 mm including brackets complete all as specified and directed by Engineer-in-Charge.

S & F in repair for Vitreous china squating pan, orissa pattern size 580 x 440mm and making good, including connection to trap, and to flushing pipe, anti-syphonage pipe, etc., including trap set and jointed in white cement, Complete all as specified and directed by Engineer-in-Charge

S & F for Vitreous China bowl urinal flat back fixed in repairs, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe), Complete all as specified and directed by Engineer-in-Charge

S & F in repairs wash down water closet (EWC) white with P or S trap including Flush pipe of polyethylene of low or high density of PVC, 32 mm dia, for low level cistern and plastic water closet seat & cover mild steel chromium plated or aluminised hinging device and connection to low level flushing cistern and flush pipe, etc complete all as specified and directed by Engineer-in-Charge.

S & F in repairs PVC connections 15mm size with PTMT nuts of length 450mm, complete all as specified and directed by Engineer-in-Charge.

S & F in repairs PVC valveless, syphonic action type, flushing cistern, low level 10 ltr capacity, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed by Engineer-in-Charge.

S&F in repair 75mm bore dia PVC floor trap(SWR) plain with grating including jointing with solvent cement to waste pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repair 75mm bore PVC(SWR) door bends any radius provided with access door complete all as specified and directed by Engineer-in-Charge.

S&F 75mm bore PVC (SWR) junction single (Single T) equal or unequal with access door complete all as specified and directed by Engineer-in-Charge.

S&F 110mm bore PVC (SWR) junction single (Single T) equal or unequal with access door complete all as specified and directed by Engineer-in-Charge.

S&F in repair 110mm bore PVC (SWR) junction double (double T) equal or unequal with access door complete all as specified and directed by Engineer-in-Charge.

S&F in repair 125/110mm bore PVC (SWR) 'P’ trap complete all as specified and directed by Engineer-in-Charge.

S&F in repair 110mm PVC (SWR) reducers complete all as specified and directed by Engineer-in-Charge.

S&F in repair 75mm PVC (SWR) vent cowl complete all as specified and directed by Engineer-in-Charge.

S&F in repair 75mm bore PVC(SWR) pipes single socketed , in any length with rubber ring joints, fixed to wall with PVC holding clamps complete all as specified and directed by Engineer-in-Charge.

S&F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall incl PVC holding clamps complete all as directed by Engineer-in-Charge.

S & F in repairs rotational moulded PVC water storage tank 500 ltr cap (cylindrical vertical with closed top) hoisted & fixed in position, complete all as specified and directed by Engineer-in-Charge.

S & F in repairs 15 mm bib tap CP fancy type screwed down screwed for iron pipe or for brass ferrulefancy typr complete all as specified and directed by Engineer-in-Charge.

S & F in repair fancy type pillar tap cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly nuts, screwed for iron pipe 15mm bore complete all as specified and directed by Engineer-in-Charge.

S & F in repair CP angle/stop valve of cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed 15 mm bore complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old painted surfaces of walls and applying one coats of distemper oil emulsion paint (Oil bound distemper) including filling of holes, cracks with cement wall care putty making surface even and smooth complete all as specified and directed by Engineer-in-Charge

Demolition, Cement concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed by the Engineer-in-Charge.

Dismantling fencing wire mesh, any type complete all as specified and directed

Taking down cement of cement plaster of any description on brick or stone walls etc including ranking out joints hacking for key scrubbing down with water etc complete all as specified and as directed by the Engineer-in-Charge

M&L for 100 mm thick PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base with out using extra cement complete all as specified & directed.

M & L for PCC 1:3:6 type C-2 (using 40 mm graded aggregate) in surface channels and drains complete all as specified and as directed by the Engineer-in-Charge.

M&L for Machine pressed precast concrete coloured interlocking paver block 80mm thick rubber moulded any shape and size over and including 25 mm thick sand layer conforming to IS 15658-2006 of grade M-40 with grey cement and no pigments complete all as specified and directed by Engineer-in-charge.

M&L for Glossy finished machine pressed rubber moulded chequred tiles of any pattern/design of size 300mm x 300mm x 25mm thick laid over cement screed bed of 15mm thick in cement mortar 1:6 in floors paths etc, complete all as specified and directed by Engineer-in-charge.

M & L for cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in coping ,bed plates and the like including slightly rounded or chamfered incl necessary formwork complete all as specified and as directed by the Engr-in-Charge.

Dismantling precast cement concrete louvres and jallis of any description and any position complete all as specified and dirtected

M&L for providing precast cement concrete type B-0 1:2:4 (12.5mm Graded stone aggregate) louvres and jallis, 25mm thick (Measured solid) set in CM 1:4 including all mouldings but excluding frame, complete all as specified and dirtected by Engineer-in-Charge.

S & F in repair galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured complete all as specified and as directed by the Engineer-in-Charge

Restraining and resecuring,existing fencing of any description including making good staples etc. as in galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair chain link fencing with 3.15mm dia wire and 50 x 50mm aperture including line wires of dia 3.15mm at three levels and tied to any type of standards,rails,etc including provision of binding wire complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of wrought iron and mild steel work of any description not otherwise provided for

M & L for hand rails, half round or other stock section or core for wooden handrail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.)& straining bolts,including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 410-0 or Fe 310-0, complete all as specified and as directed by the Engineer-in-Charge

M & L for brickwork with subclass `B` bricks, in straight or curved on plan exc 6m mean radius, built in CM 1:4, complete all as specified and as directed by the Engineer-in-Charge

M & L for brickwork with subclass `B` bricks, in straight or curved on plan exc 6m mean radius, built in CM 1:4 (except brick) complete all as specified and as directed by the Engineer-in-Charge

M & L for mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by the Engineer-in-Charge

M & L for formwork to soffit of suspende slabs such as roof slabs, floor slabs, landing and similar works not exc 200mm thick complete all as specified and as directed by the Engineer-in-Charge

M&L for RCC Nominal Mix Type B-1 1:2:4 (Using 20mm Graded stone aggregate) as in slabs supported on walls, beams and columns in floors roofs, landings, balconey, canopies, parapes, copings, shelves etc complete all as specified and as directed by the Engineer-in-Charge

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m deep and getting out in any type of soil, complete all as specified and directed by Engineer-in-Charge.

Returning filling in including spreading, levelling, watering and well ramming in layers n.exc 25cm thick in soil complete all as specified and directed by Engineer-in-Charge.

Removal of excavated soil to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed by Engineer-in-Charge.

Demolition and breaking up drain pipe 150 mm dia any type (salt glazed stone ware) of any size internal dia, set in cement mortar, including demolition of concrete bed and haunching complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) pipes single socketed 150mm bore, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed by Engineer-in-Charge.

Dewatering of septic tank/soakage well of any depth by pump or by manual after plugging of incoming sewage lines and throwing water into non residential area or in drain/nallah complete all as specified and directed by Engineer-in-Charge.

Cleaning of septic tanks, soakage well of any depth including inlet and outlet chamber and removing sludge, silt, residue both organic and in-organic nature including any other type of waste material after plugging of incoming sewage line and removing waste material/sludge etc to a distance n.exc 300m and burrying in a pit complete all as specified and directed by Engineer-in-Charge.

Cleaning of underground sewage pipe (Cleaning length n.exc 30m from manhole to manhole or from manhole to septic tank) including taking off manhole cover and cleaning of manholes of any size and depth and removing waste material/sludge to a distance of n.exc 300m and burrying in a pit and replacing manhole cover in position after cleaning complete all as specified and directed by Engineer-in-Charge for the following size of pipes:

100mm bore

150mm bore

200mm bore

Taking down carefully copper/aluminium point wiring (light, fan, socket, bell or power) complete including all electrical fittings & fixtures and making good disturbed surfaces of wall , floor etc and matching with original colour of wall, complete, all as specified & directed.

Material and labour for Point wiring with 1.5 sq mm copper conductor FRLS (multistranded) PVC insulated ISI marked unsheathed cable 1100 volts grade in and including concealed/surface , non metalic rigid PVC medium grade ISI marked conduit not less than 19 mm with all fittings & other accessories including PVC insulated ISI marked unsheathed FRLS cable 1100 volts grade of size 1.5 sq mm copper conductor as earth wire to common earth dolly concealed in wall/ceiling, modular MS box with modular cover plate and frame suitable for modular switches, sockets, fan regulator etc for the following :- Note - Colour code of cable Phase-Red Neutral- Black and Earth -Green)

One light/fan/bell point controlled by one way switch 6 amps 240 volts

One light point controlled by two way switch 6Amps 240 volts

One 3 pin 6 Amps switch socket out let point on independent board

One 3 pin 6 Amps switch socket out let point on same board

M&L for Point wiring with 2.5 sq mm copper conductor FRLS (multistrand) PVC insulated ISI marked unseathed cable 1100 volt grade in and including concealed/surface , non metalic rigid pvc medium grade ISI marked conduit not less than 19 mm with all fittings & other accessories and also including PVC insulated ISI marked unseathed FRLS cable 1100 volts grade of size 1.5 sq mm copper conductor as earth wire to common earth dolly including concealed in wall/ceiling, modular MS box with modular cover plate with frame suitable for modular switches, sockets 16 Amps, 240 volts Note - Colour code of cable Phase-Red Neutral- Black and Earth -Green)

S&F modular one way switch 6 Amp 240 volt marked light/fan suitable for one model etc complete as specified and directed. Make- Legrand/ ABB/ Havells or equivalent approved by GE

S&F modular two way switch 6 Amp 240 volte suitable for one model etc complete as specified and directed. Make- Legrand / ABB/ Havells or equivalent approved by GE

S&F Modular 6 Amp 5 pin universal socket suitable for two model , 250 volts complete all as specified and directed by Engr-in-charge. Make Legrand/ ABB/ Havells or equivalent approved by GE

S&F modular switch one way 16 Amps 240 volts suitable for one model complete as specified and directed by Engr-in-charge. Make- Legrand/ ABB/ Havells or equivalent approved by GE

S&F Modular 6/16 Amp socket suitable for two model , 250 volts complete all as specified and directed by Engr-in-charge. Make: Legrand /ABB/ Havells or equivalent approved by GE

S&F switch piano flush type single pole, one way 6 Amps 240 ISI marked etc complet as specified and directed. Make : Legrand/ ABB/ Havells or equivalent approved by GE

S&F in repair socket outlet 2 in 1, 3 pin 6 A flush type ISI marked 240 volts ISI marked etc complete as specified and directed. Make- Legrand/ ABB / Havells or equivalent approved by GE

S&F in repair switch socket combination 2 in 3 pin 5 and 16 Amps flush type ISI marked universal suitable for 240 volts etc complete as specified and directed. Make- Legrand/ ABB/ Havells or equivalent approved by GE

S&F in repair stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc complete as specified and directed Make- Legrand/ ABB/ Havells or equivalent approved by GE

M&L for ceiling rose with three terminal as per relevant IS complete as specified and directed. Make- Legrand/ ABB/ Havells or equivalent approved by GE

Lamp holder PVC/polycarbonate type with back plate suitable for batten fitting incl 10 watt LED lamp etc complete all as specified and directed

S&F in repair decorative Self ballasted LED Batten With Extruded Thermoplastic body with PC diffuser fitting with>120º wide Distribution 16 watt luminaire ,complete all as specified & approved by Engr-in-charge Make:-Wipro /Havells /Crompton

S&F in repair Energy saving new generation 10 W LED IP 65 bulkhead luminair with opal diffuser with 10 LED lamp etc complete as specified and directed by Engr-in-charge Make:- Wipro /Havells/Crompton

S&F in repair mirror light sleek LED 10 W mirror light provided with high output diffuser with suitable capacity driver with all comptonants as per manufacturer etc complete as specified and directed. Make:- Wipro/Havells/Crompton

S&F in repair modular step type fan regulator suitable for 120 watt 250 volts etc complete as specified and directed Make- Legrand/ ABB or equivalent approved by GE

S&F recess/ surface/ suspended mounted LED 36 watt slim ceiling light with extruded aluminium housing and milky diffuser complete as specified and directed. Make: Wipro Cat Part No CRCO10R038HP57GL1 or equivalent in Havells /Crompton

S&F LED CMPRI certified LED flameproof 16W tube light fitting recommended for Gas/vapour group of II A & II B and Zone 1&2 with all accessoreis & including 3 core flexible cable and metalic flexible conduit from ceiling rose to connector of fitting etc complete as specified and directed by Engr-in-charge. Make: Crompton model No EXTN1LT8-16/20 or equivalent in Havells /sudhir approved by GE.

S&F in repair Recess/surface/suspended mounted LED 18 watt slim ceiling light with extruded aluminium housing and milky diffuser complete as specified and directed by Engr-in-charge. Make: Wipro Cat Part No CRDL11R023HP57* or equivalent Havells /Crompton

S&F in repair decorative post top lantern for 360 C indirect light resistant to impact and corrosion, Glare free and better uniformity IP-65 protection miliky version with all accessoreis complete as specified and directed by Engr-in-charge. Make: C&S model No LTGL30-24X1HPLED or equivalent Havells /Wipro

S&F in repair LED flood light 100 watt IP 66 high power flood light with pressure die cast aluminium housing complete with all accessories including 3 core flexible cable from ceiling rose to connector of fitting etc complete as specified and directed. Make : Wipro Cat Part No. LF20-122-060-57-G2 or equivalent Havells / Crompton

S&F in repair LED flood light 60 watt IP66 high power flood light with pressure die cast aluminium housing complete with all accessories including 3 core flexible cable from ceiling rose to connector of fitting etc complete as specified and directed by Engr-in-charge. Make:-Wipro Cat Part No. LF19-711-060-57-XX or equivalent Havells /Crompton

S&F in repair heavy duty exhuast fan 300mm sweep,1400 RPM turbo force model single phase, 240 volts with louverand all accessories as per manufacturer norms with 3 core flexible cored from ceiling rose to connector of fitting etc complete as specified and directed by Engr-in-charge. Make -Havells/Usha/Crompton

S&F in repair heavy duty exhuast fan 450mm, 1400 RPM turbo force model single phase with louvers and all accessories as per manufacturer norms including 3 core flexible cord from ceiling rose to connector of fan etc complete as specified and directed by Engr-in-charge. Make -Havells/sudhir/Anchor

S&F in repair epoxy powder coated or polystrene insulated material sheet metal enclosure factory made (double door) 12 way SPN suitable for MCB DB's 240 Volts with 200 Amps rated busbar, neutral & earthing link bar, flush/surface mounting complete all as specified and directed. Make- Legrand/ Usha/Crompton

S&F in repair MCB single pole ISI marked ISI Marked `C' series working on 240 Volts 50 HZ AC supply for incomming and out going controlling cercuit of capacity 6-32 Amp breaking capacity 10 KA etc all as specified and directed. Make- Legrand/ ABB/ Havells

S&F in repair MCB single pole and neutral ISI marked `C' series working on 240 volts 50HZ AC supply for incomming & out going controlling system of capaicty 40-63 Amps 10 KA breaking capacity etc all as specified and directed. Make- Legrand/ ABB/ Havells

M&L for sub main wiring with two single core, PVC insulated,ISI marked, unsheathed, 1100 volts grade multistranded copper conductor FRLS cable drawn into and including suitable size pvc conduite ISI makred medium grade concealed/surface with all accessories and including one single core pvc insulated multistranded unsheathed 1100 volts grade copper conductor FRLS cable as earth wire of the size 2x6.0 sqmm + 1x6.0 sqmm earth wire as in repair complete all as directed & specified.

M/S M.R. Construction

M/S Wani and Sons

M/S GULAM AHMAD ABDUL SAMAD

M/S Abdul Ahad Rather