PROVN OF 04 MT STORE ROOMS FOR EACH PLATOON IN TPT COY ASC (CIV GT) ZONE-III AND SPL REPAIRS OF QTR NO 352/1 AND 352/3 IN OFFICER MD ACCN OF ZONE-I (A) AREA AT JAIPUR MIL STN

Amount

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft / loose soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5m depth for foundation etc or for shafts, wells cesspits manholes pier holes etc not exceeding 10 sqm on plan and in soft /loose soil etc complete all as specified and directed.

Returning, filing in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/loose soil etc complete all as specified and directed

M&L for sand filling under floor or in foundations including watering and consolidation complete all as specified and directed. Note:- Punned thickness of sand shall be measured and paid.

Removal of excavated materials (soil) not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting points etc complete all as specified and directed.

M&L for broken stone or boulders hardcore of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured ) complete all as specified and directed.

Treating the top surface of filled earth at the rate of 5 Litre of emulsion per sqm of surfaces

M&L for treating the soil along with external perimeter of building at the rate of 2.25 litres of emulsion per metre of perimeter wall complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in lintels upto 1.5 m clear span, cills, copings, bed plate, plinth courses, roof kerbs or mud stops rounded or chamfered on edges including necessary form work complete all as specified and directed.

M&L for Precast cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in landings, cover slab (for manholes etc), chullah hoods, chajjas, water troughs, mangers, shelves and similar work including necessary form work and set in CM 1:6 complete all as specified and directed.

M&L for providing precast cement concrete louvres and jallies 35 mm thick (measured solid) including all mouldings but excluding frame in cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregates and set in cement mortar 1:4 complete all as specified and directed.

M&L for RCC (design mix) M-25 using 20 mm graded stone aggregates as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concrete complete all as specified and directed . Note - Reinforcement and form work shall be measured and paid separately.

M&L for RCC (design mix) M-25 using 20 mm graded stone aggregates as in slab supported on wall, beam and column in floors, roofs, landings, balconies, canopies and in shelves and similar work complete all as specified and directed. Note - Reinforcement and form work shall be measured and paid separately.

M&L for RCC (design mix) M-25 using 20 mm graded stone aggregates as in chajjas and similar work complete all as specified and directed. Note - Reinforcement and form work shall be measured and paid separately.

M&L for RCC (design mix) M-25 using 20 mm graded stone aggregates as in beam, cantilevers, bressummers, lintels over 1.5 m span and similar work complete all as specified and directed. Note - Reinforcement and form work shall be measured and paid separately.

M&L for RCC (design mix) M-25 using 20 mm graded stone aggregates as in columns, pillars, piers, posts and struts and similar work complete all as specified and directed. Note - Reinforcement and form work shall be measured and paid separately.

M&L for cutting holes into or through cement concrete slabs, chajjas, etc. reinforced or otherwise of superficial area n.exc. 100sqcm complete all as specified and directed.

M&L for applying bond coat of epoxy bonding agent & cement in 1:1 ratio for bonding old and new concrete on damaged surfaces after applying anticorrosive paint over cleaned rusted steel surface including demolition old RCC surfaces (chajjas, fins, beams , borders etc and applying 30mm thick polymer modified mortar in CM 1:3 including mixing of polymer latex additives for repair of Chajjas fins, border etc complete all as specified and directed. Note :- (i) Cleaning of rusted part of steel and applying anticorrosive paint over it. (ii) Qty of ploymer to be used 15% by weight of the cement or as per manufacturer instruction. (iii) Use of electrical mixer to get the homogeneous dough on bond coat surfaces. (iv) To achieve required thickness repeat this step after 24 hrs as required. (v) Keep the surfaces moist using water fog for 5 to 7 days etc complete all as specified and as directed. (vi) Rate shall be inclusive of all necessary scaffolding for building of height upto two storey. Make :- (i) The epoxy bonding agent shall be Krishna / Dr Fixit / MC Bauchemie / M/s Cemistik / Sika or equivalent as approved by GE. (ii) Polymer latex addictive shall be of Sika / Fosroc / Dr Fixit or equivalent as approved by GE.

M&L for chipping of unsound weak and cracked concrete/cover of reinforcement over RCC member or as per site requirement by chieseling and disposal of malwa from site complete all as specified and directed.

M&L for re-building the section of damaged RCC elements to its original size on an average 15 mm thickness in two layers each by providing and applying with pre- batched, polymer modified mortar of approved make having compressive strength>= 50 N/sqmm (28 days) according to ASTM C 109: Flexural strength >= 5 N/sqmm (7 days) according to ASTM C 293-79 complete all as specified and directed. Make : Fosroc / Thermax / Sika or as approved by GE.

M&L brick work using old size sub class 'B' bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L brick work using old size bricks with sub class 'B' bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

M&L for cutting holes into or through stone walls built in cement mortar or cement lime mortar and walls of cement concrete and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required for superficial area exc 150 sq. cm but not exc 400 sq. cm complete all as specified and directed.

M&L for brick protection cover to the under ground cable (with old size sub class 'B' bricks) with width equal to length of brick laid dry and flat abutting each other with gaps between adjacent brick not exceeding 10 mm all as specified and directed.

M&L for walling of random rubble uncoursed stone masonry, well bonded, bedded and solidly hearted built in cement mortar 1:6 complete all as specified and directed.

M&L 15-16 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified & directed.

M&L for Form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams etc and similar work, vertical or to batter for rough finished flat concrete surfaces complete all as specified and directed.

M&L for Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200 mm thick (horizontal or sloping) for rough finished flat surface of concrete complete all as specified and directed

M&L for Form work to chullah hood, chajjas, troughs and similar items including edges etc for rough finished flat concrete surface complete all as specified and directed.

M&L for Form work to sides and soffits of floor or roof beam, beam hauchings, girders, bressummers, lintels, cantilevers, shelves, for flat rough finished concrete surfaces complete all as specified and directed.

M&L for Form work to sides of pillars, posts, struts, piers, columns and stanchions for square, rectangular or polygonal rough finished concrete surface complete all as specified and directed

M&L for Form work to edges of concrete flats, treads breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roof and sides of bands in walls, horizontal or sloping and similar work for rough finished concrete surface exc 10 cm but not exc 20 cm wide complete all as specified and directed.

S&F second class hard wood 35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass , gauze etc with out sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR part I section 8 clause 8.24 (a) complete all as specified and directed.

S&F 35 mm thick second class hard wood rail and style plain framed factory made panelled shutter (two panel) with lock rail and panel of 9 mm BWP commerical ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 35 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

Taking down chowkats or frames n.exc 1.5 Sqm each with shutters (without taking off shutters from the frames) and removing to or from store complete all as specified and directed.

Taking down chowkats or frames exc 1.5 sqm but not exc 4.0 sqm each with shutters (without taking off shutters from the frames) and removing to or from store complete all as specified and directed.

Taking down shutters of any description exc 1.00 Sqm but not exc 2.00 Sqm each and refixing in the other opening after repair complete all as specified and directed.

Taking down shutters of any description exc 1.00 Sqm but not exc 2.00 Sqm each and removing to or from store complete all as specified and directed.

S & F for solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplied and fixing in opening as specified and shown on drawing made on section 8 of SSR 2020 Part-II complete all as specified and directed

S & F Factory made Solid PVC Moulded door shutter with Wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2 mm thick moulded Prelam PVC Sheet on the front face & 2 mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolts of extruded section 150 mm long complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolts of extruded section 200 mm long complete all as specified and directed.

S&F aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy of 250 mm length of bolt complete all as specified and directed.

S&F in repair aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy of 250 mm length of bolt complete all as specified and directed.

S&F Butt hinges, medium weight, cold rolled mild steel 100 mm long complete all as specified and directed.

S&F 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F aluminium handles cast type anodised of 150 mm size complete all as specified and directed.

S&F in repair aluminium handles cast type anodised of 150 mm size complete all as specified and directed.

S&F Mortice lock, vertical type, size 100 mm, 4- lever brass body with two keys complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rail, 20mm dia complete as all specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repair stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S & F auto close hinges, stainless steel, bright finish or electrogalvanised fixed complete all as specified and as directed.

S&F stainless steel handles, fancy type, of 200 mm size complete all as specified and directed.

S&F stainless steel (SS) tower bolts, fancy type, of size 150 mm long complete all as specified and directed.

M&L for cupboard magnet, stainless steel, bright finish or electro-galvanised of size 55 x 29mm complete all as specified and directed .

M&L for cupboard lock, stainless steel, bright finish or electro-galvanised of size 64mm complete all as specified and directed .

S&F stainless steel handles, fancy type, of 100 mm size complete all as specified and directed.

S&F 75mm long floor door stopper of stainless steel body with rubber shoe complete all as specified and directed.

S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and / or riveted or forged into spikes, framed guard bars, barred iron doors and similar work conforming to Fe -290 Gde E-165 complete all as specified and directed.

M&L for mild Steel TMT bar 10 mm dia and over cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild Steel TMT bar 5mm dia and over upto and including 10mm dia as in stirrups, spacers & binders cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F 1.25 mm thick of steel rolling shutters without ball bearing as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer erected in position as indicated, push pull or manual type complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges steel peg stay complete all as specified and directed

S&F pressed steel frames of size 125 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including one shop coat of priming complete all as specified and directed.

M&L for powder Coated (minimum thickness of powder coating 50 micron) anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F for powder coated (thickness of powder coating not less than 50 micron) anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed. Note-Glass and other filling material in panels shall be measured and paid seperately

S&F steel windows factory made of MS hollow section 79mm x 39mm x 1.6mm thick frame with double shutter welding and tennon riveting dobby hinges shall be provided to both shutters, locking arrangements as per sample approval by GE provided with knob, 10mm MS square bars in grill, Z section handle 100mm size and 150mm long hook welded to frame and shutter, four Nos lugs welded to frame including necessary flat iron beading for securing wire gauge etc including cutting holes for hold fast and making good in PCC 1:2:4 type B-0 complete all as specified and directed. Note : Wire mesh and sheet glass shall be measured & paid separately under respective items.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof overing/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed.

Taking down eaves gutters and rain water pipes (any size or pattern) including all fittings, heads, shoes, bends, swan-necks, etc including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) etc complete all as specified and directed.

M&L for carried out water roof treatment as under :- (a) Complete removal of existing roof treatement and disposed off the rubbish outside the defence land. (b) Preparation of dry surface and laying 25mm thick PCC type B-0, (1:2:4) using 12.5mm graded stone aggregate finished even & smooth without using extra cement to cover negative slope into prop with including WPC @ 3% weight of cement or as per manufactururer instruction. (c) All visible cracks to be opened up in V shape cleaned properly with wire brush washed and filled with cracks filling compound for cracks upto 5mm width / depth of cracks. (d) Cracks of more than 5mm width / depth are filled with URP cement grouting by injecting through nozzles till refusal by authorised applicator of manufacturer, carefully by following manufacture instruction. The size and spacing of nozzles shall be as per manufacturer instruction or as directed by Engg-in-Charge. (e) M&L rendering 10mm thick in cement mortar (1:3) on concrete surfaces to receive water proofing treatment finished even and smooth complete all as specified. (f) Necessary gurantee for 5 years shall be submitted by the contractor. Make :- Cement Grout : Dr. Fixit (Fixit Pidicrete URP Model:301) or equivalent in Fosroc / Choksey chemicals / Sika / Berger (HS Super Grout) or equivalent as approved.

M&L for fibre reinforced, UV resistant elastomeric liquid applied water proof coating over cementitious surfaces, highly elastic and hairline crack bridging capacity (elongation 250-350%), non toxic, VOC complaint water based coated in three layers first being priming coat, forming complete tihckness as metioned by OEM and complete all as specified and directed. Make:- Asian / Berger / Sika or equivalent.

M&L decorative laminate type 1 of 0.9 thickness of surface finish, colour and pattern as approved, fixed with approved adhesive complete all as specified and directed .

M&L for 18-20 mm thick High Density high moisture resistant (HDHMR) board for kitchen cupboard / door shutter of Action tesa / Pearlwood or equivalent make as approved by GE, one side colour / white laminate and other side decorative as in modular kitchen / cabinets / door shutter fixed with minifix hardware wherever required including edge band 22mm wide, 0.80mm thick of matching colour on exposed surfaces of board fixed with polymaster adhesive of REHAU make or equivalent including trimming edges of edge band to true line of thickness of board by manual trimmer, fixed to wall etc. complete all as specified and directed.

M&L for 8 mm thick HDHMR (High density high moisture resistant) board of Action tesa / Greenply or equivalent make both side white laminate as in back of kitchen cabinets/portion of cupboard etc complete all as specified and directed.

M&L for machine cut kota stone slab flooring mirror finished 20-25 mm thick (each slab not less than 0.25 sqm) over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing on treads of step and landing of stair including screed bed 20 mm thick in CM 1:6 complete all as specified and directed.

M&L for machine cut kota stone slab mirror finished 20-25 mm thick (each slab not less than 0.25 sqm) in riser of step ,skirting, dado and pillar over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including rendering 10 mm thick in CM 1:4 complete all as specified and directed.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

M&L for 75 mm thick Cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate as in sub base complete all as specified and directed.

M&L for PCC 1:3:6 type C2 using 40 mm graded stone aggregate, 75 mm thick in plinth protection laid in panels and finished even and smooth without using extra cement including necessary form work complete all as specified and directed.

M&L for 100 mm thick Cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified and directed.

M&L for 75 mm thick Cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in sub base flooring 25 mm thick surface finished even and rough to receive the topping layer complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in sub base flooring 25 mm thick surface finished even and smooth with using extra cement complete all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surface 350x 250x 7 mm / 450X 350X 7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match surface of tiles over and including rendering 10 mm thick in CM 1:4 complete all as specified and directed.

M&L for non skid ceramic coloured tiles of design as approved 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over and including screed bed 15 mm thick in CM 1:6 complete all as specified and directed.

M&L for non skid ceramic coloured tiles of design as approved 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for non skid ceramic coloured tiles of design as approved 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in vertical surface etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished area of each tiles not exceeding 0.36 sqm in vertical surface such as dado / skirting / risers to steps etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 10 mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished area of each tiles not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over and including screed bed or bedding layer 15 mm thick in CM 1:6 complete all as specified and directed.

M&L for Terrazzo tiles 20cm x 20 cm x 20mm thick, with size of chips upto 6 mm; set with grey cement and pigment jointed and pointed in neat cement slurry in floors, and cut and polished and including screed bed 15 mm thick in CM 1:6 complete all as specified and directed.

S&F machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, coloured, M-35 Grade with grey cement and pigment laid over and including sand cushing 25 mm thick complete all as specified and directed.

M&L for chequered cement concrete tiles 25 cm x 25 cm x 22 to 25 mm thick set, jointed and pointed in neat cement slurry as in floors with grey cement and no pigments over and including 20 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding etc (but not backing) and removing rubbish off the premises complete all as specified and directed.

M&L for rendering 10 mm thick in CM 1:3 as in ceiling surface and finished even and smooth with out using extra cement complete all as specified and directed.

M&L for rendering on fair faces of brick work or concrete surface of wall 15 mm thick in CM 1:6 and to be finished even and smooth with out using extra cement complete all as specified and directed

M&L for rendering on fair faces of brick work or concrete surface of wall 15 mm thick in CM 1:4 and to be finished even and smooth with out using extra cement complete all as specified and directed

M&L for rendering on stone masonry or other than fair faces of brick work of wall 15 mm thick in CM 1:6 and to be finished even and smooth with out using extra cement complete all as specified and directed.

M&L for rendering on stone masonry or other than fair faces of brick work of wall 15 mm thick in CM 1:4 and to be finished even and smooth with out using extra cement complete all as specified and directed.

M&L for 15 mm thick screed bed or bedding layer in CM 1:4 surface finished fair and even for laying floor finishes complete all as specified and directed.

Taking down cement plaster any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M&L for raking out joints/ pointing to brick work in walls or to bricks on edge in floors, surface channels, roofs etc., built in cement or cement lime mortar complete all as specified and directed .

M&L for preparation of newly plastered surfaces of walls and apply three coat of white wash complete all as specified and directed.

M&L for preparation of old decorated surfaces of walls by brooming or steel wire brushing scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and making good using putty wherever required and apply two coat of white wash complete all as specified and directed

M&L for preparation of new surface of wall of any description and applying two coats of oil bound distemper (OBD) over a coat of chalk whiting on plastered surfaces preparatory to distempering over and including 1 mm thick wall putty all as specified and directed.

M&L for complete removal of existing treatment and preparation of old surface of wall of any description and applying two coats of oil bound distemper (OBD) over a coat of alkali-resistant priming paint over and including 1 mm thick wall putty all as specified and directed.

M&L for preparation of newly plastered surfaces of ceilings and apply three coat of white wash complete all as specified and directed.

M&L for preparation of old decorated surfaces of ceiling by complete removal of existing treatment and apply two coat of white wash complete all as specified and directed

M&L for preparation of new plastered surfaces of ceiling and applying two coat of oil bound distemper over a coat of alkali resisting priming paint complete all as specified and directed.

M&L for preparation of new surface of walls of any description with a coat of 1 mm thick wall putty and applying two coats of acrylic emulsion exterior grade weather proof paint over a coat of primer complete all as specified and directed.

M&L for complete removal of existing treatment and preparation of old surface of wall of any description with a coat of 1 mm thick wall putty and applying two coats of acrylic emulsion exterior grade weather proof paint over a coat of primer complete all as specified and directed. Note :- Acrylic Emulsion Paint shall be carried out as specified in clause 15.17 of SSR Part-I including all necessary arrangement such as scaffolding / working plateform for execution of work upto four storey building etc.

S&F 4.8 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane, complete all as specified and directed.

S&F 5.5 mm thick sheet glass, ordinary quality and glazing with oil putty in square exceeding 0.5 Sqm in each pane, complete all as specified and directed.

S&F figured glass 3 mm thick, pin head type and glazing with oil putty in squares not exc 0.5 sqm in each pane complete all as specified and directed

S&F figured glass 4 mm thick, pin head type and glazing with oil putty in squares not exc 0.5 sqm in each pane complete all as specified and directed

M&L for preparation of old painted surfaces of wood and wood based surfaces of any description, over 10 cm in width or girth and apply one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, over 10 cm in width or girth and apply two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new or previously untreated plastered or concrete surface of any description, over 10cm in width or girth and apply two coat of synthetic enamel paint over a coat of primer complete all as specified and directed.

M&L for preparation of old painted surfaces of steel of any description, over 10cm in width or girth and apply one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel of any description, over 10cm in width or girth and apply two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Fixing only tubes, any grade, 15 mm bore of pipe to walls and ceilings or laying in floors complete all as specified and directed.

Fixing only tubes, any grade, 20 mm bore of pipe to walls and ceilings or laying in floors complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning if refixing required for 15 mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning if refixing required for 20 mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning if refixing required for 25 or 32 mm bore of pipe complete all as specified and directed.

M&L for 3-layer PP-R Polypropylene random copolymer, concealed pipes SDR 7.4 (PN16) UV stabilized of 16 mm outer dia and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded Polypropylene random fittings fixed to walls, ceilings or in floors etc. complete all as specified and directed.

M&L for 3-layer PP-R Polypropylene random copolymer, concealed pipes SDR 7.4 (PN16) UV stabilized of 20 mm outer dia and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded Polypropylene random fittings fixed to walls, ceilings or in floors etc. complete all as specified and directed.

M&L for 3-layer PP-R Polypropylene random copolymer, concealed pipes SDR 7.4 (PN16) UV stabilized of 25 mm outer dia and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded Polypropylene random fittings fixed to walls, ceilings or in floors etc. complete all as specified and directed.

Dismantling of AC/PVC water tank and S & F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) 500 litre capacity hoisted and fixed in position complete all as specified and directed

Dismantling of AC/PVC water tank and S & F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) 1000 litre capacity hoisted and fixed in position complete all as specified and directed.

S&F in repair bib taps cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule fancy type chromium plated of 15 mm bore dia of pipe complete all as specified and directed. Make : Jaquar / Hindware / Cera or equivalent as approved by GE.

S&F for 15mm bore dia of pipe brass CP, WHB mixer for mixing hot & cold water screwed down for iron pipe complete all as specified and directed.

S&F for 15mm bore dia of pipe brass CP kitchen mixer for mixing hot & cold water screwed down for iron pipe complete all as specified and directed.

S&F in repair for 15mm bore dia of pipe brass CP wall mixer for mixing hot & cold water screwed down for iron pipe complete all as specified and directed.

S&F in repair stop valves, fancy type, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions for 15 mm bore dia of pipe complete all as specified and directed.

S&F in repair stop cock cast copper alloy, screwed down, high pressure with crutch or butterfly handle chromium plated with long shank and cup (concealed type) screwed both ends for iron pipe or for unions for 15 mm bore dia of pipe complete all as specified and directed.

S&F in repair Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe of 15 mm bore dia of pipe complete all as specified and directed.

S&F in repair Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe of 20 mm bore dia of pipe complete all as specified and directed.

S&F PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of 75 mm bore of pipe etc complete all as specified and directed.

M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of 110 mm bore of pipe etc complete all as specified and directed.

M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls of 75 mm bore of pipe etc complete all as specified and directed.

M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls of 110 mm bore of pipe etc complete all as specified and directed.

S&F PVC (SWR) bends any radius of 75 mm bore without access door complete all as specified and directed.

S&F PVC (SWR) bends any radius of 110 mm bore without access door complete all as specified and directed.

S&F PVC (SWR) junction single,(Single T) equal or unequal of 110 mm bore of pipe with access door complete all as specified and directed.

S&F PVC (SWR) junction single,(Single T) equal or unequal of 75 mm bore of pipe with access door complete all as specified and directed.

M&L PVC (SWR) vent cowl 75 mm complete all as specified and directed.

M&L PVC (SWR) vent cowl 110 mm complete all as specified and directed.

M&L PVC (SWR) reducers 75 mm complete all as specified and directed.

S&F for 32 mm bore brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and directed.

M&L PVC (SWR) multi floor trap of diameter of outlet 75 mm, plain with grating including jointing with solvent cement complete all as specified and directed

M&L PVC (SWR) gully trap 125/110 mm setting and jointing with solvent cement complete all as specified and directed

S&F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including fixing cantilever brackets and connecting union to pipe, overall size 915 mm x 460 mm, bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm, bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repair Water closet vitreous china squatting pan, orissa pattern 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) and including provision of lime concrete bedding ,'P' or 'S' trap 100 mm bore , flushing pipe ,anti-syphonage pipe and connection etc and making good to floor complete all as specified and directed.

S&F in repair PVC 10 litres capacity valveless ,syphonic action type low level flushing cistern ,white including flush pipe, inlet, ball valve, float and handle etc complete all as specified and directed.

S&F in repair brass chromium plated shower rose 125 mm size with or without swivel joint complete all as specified and directed.

M&L toilet paper holder , of stainless steel with flat recessed type, chromium plated, fixed to walls with chromium plated (CP) brass screws complete all as specified and directed. Make : Jaquar / Hindware / Cera or euivalent as approved by GE.

M&L in repair for vitreous china wash basin, white,flat back, size 550 x 400 mm with pedestal, brackets, including PVC connection of 450 mm long, PVC (HDPE) 32 mm bore waste pipe, brass couplings 32 mm CP etc. complete all as specified and directed.

S&F Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed. Make : Jaquar / Hindware / Cera or equivalent as approved by GE.

S&F for chromium plated soap dish holder complete all as specified and directed.

S&F chromium plated towel ring complete all as specified and directed. Make-Jaquar or euivalent as approved by GE

S&F float corner glass shelve 8 mm thick 300 mm radius complete all as specified and directed.

S&F in repair white rimless single piece- EWC with UF soft close slim seat cover, Hinges, fixing accessories and accessories set and cistern fittings, S trap including fixing as per manufacturer instructions complete all as specified and as directed. Make : Jaquar CAT Part No OPS-WHT-15853S300UF / Roca Cat Part No. RS34273700H / Kholer Cat part No. K-77739T-SL-0 / Cera Cat Part No. S1013245 or equivalent as approved by GE.

S&F in repair bib taps 2-in-1 cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule fancy type of 15 mm bore dia of pipe complete all as specified and directed. Make : Jaquar CAT Part No KUP-CHR-35041PM / Hindware CAT part No. F320005CP / Cera CAT Part No F1018163 or equivalent as approved by GE.

S&F bathroom cabinet with mirror of size 300 x 450 mm fixed with and including chromium plated brass screws and wooden / plastic cleats complete all as specified and directed.

S&F kitchen plain baskets of stainless steel size 17" x 20" x 4" of grade SS-304 complete all as specified and directed. Make : Godrej / Hindware / Lifetime or equivalent make as approved by GE.

S&F Stainless Steel Towel Rack 600mm Long complete all as specified and directed.

S&F kitchen perforated cutlery baskets of stainless steel size 17" x 20" x 4" of grade SS-304 complete all as specified and directed. Make : Godrej / Hindware / Lifetime or equivalent make as approved by GE.

S&F kitchen cup & saucer baskets of stainless steel size 17" x 20" x 4" of grade SS-304 complete all as specified and directed. Make : Godrej / Hindware / Lifetime or equivalent make as approved by GE.

S&F kitchen plate baskets of stainless steel size 17" x 20" x 4" of grade SS-304 complete all as specified and directed. Make : Godrej / Hindware / Lifetime or equivalent make as approved by GE.

S&F kitchen grain baskets of stainless steel size 17" x 20" x 4" of grade SS-304 complete all as specified and directed. Make : Godrej / Hindware / Lifetime or equivalent make as approved by GE.

S&F stainless steel baskets guide channels suitable for running basket of grade SS-304 complete all as specified and directed.

S&F in repair for Bathroom Duct Pipelines for Waste Water Pipe, Domestic Water Pipes and Riser supply down take pipes fixing done with Pipe Supporting Clamping System having Profile Bracket + Slotted C Channel + U Bolt R/M System - 1. Waste Water Pipe 2 1/2" PVC, 2. Water Supply Down take lines 3/4" GI - 2 nos. and 3. Riser Supply Down take pipelines 3/4" GI - 1 nos. running from Terrace to Ground Floor Vertical Fixed line with wall distance 4": Pipe Support Clamping made of 1. Profile Bracket Type A2 (Wall Distance 4") made of Low Carbon Hot Roll gauge corrected Oil Pickled & Drawn (HROP D) Steel (IS 1079); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanized + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Slotted "C" Channel B3 Type to be Continue...at serial item No. 183.01

Continue...from serial item No. 183.00 used of size 20" (Continuous Slotted "C" Channel with ribs) made of Low Carbon Hot Roll gauge corrected Oil Pickled & Drawn (HROP D) Steel (IS 1079) are Hot Dip Galvanized + Zn Al Flake coated of material 48 x 3mm. 3. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hot dip Galvanizing as per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade :- IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty.:- 1. Profile Bracket of A2 Type (Wall distance 4") - 2 Nos. 2. Continuous Slotted C Channel of B3 Type Size 20" - 1 No.; 3. U Bolt R/M for 2 1/2" PVC Pipe Dia. - 1 No.; 3/4" GI pipe Dia. - 3 nos. Pipe Support Clamping Unit fixing to be done at every metre distance in the duct as specified in the Technical Drawing. (Refer CE Jaipur Zone Technical Drawing no. TD/2022/01.) Make :- Shaivi or equivalent as approved by GE.

S & F repair of Toilet Duct Pipelines for Soil Water Down take pipe fixing done with Pipe Supporting Clamping System having Profile Bracket + Slotted C Channel + U Bolt System - 1. Soil Water Pipe 4" PVC - 2 pipe and running from Terrace to Ground Floor Vertical Fixed line with wall distance 3": Pipe Support Clamping made of 1. Profile Bracket Type A2 (Wall Distance 3") made of Low Carbon Hot Roll gauge corrected Oil Pickeled & Drawn (HROP D) Steel (IS 1079); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Slotted "C" Channel B3 Type to be used of size 22" (Continuous Slotted "C" Channel with ribs) made of Low Carbon Hot Roll gauge corrected Oil Pickeled & Drawn (HROP D) Steel (IS 1079) are Hot Dip Galvanzied + Zn Al Flake coated with material thickness of 3mm. 3. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated.

M&L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 sq. mm 4 core complete all as specified and directed. Note:- Excavation,earth work,sand,brick and protection pipe shall be measured and paid seperately.

S&F LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

Taking down copper / aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

M&L for point wiring complete with 1.5 Sqmm single core (Phase - Red, Neutral - Black) PVC insulated and unsheathed multi stranded copper conductor FRLS cable of 1100 V grade PVC insulated and unsheathed cable inclosed in and including concealed PVC conduit 20 mm dia medium grade with all accessories ISI marked, including MS sunken box of thickness not less than 1.2 mm, cover with 3 mm thick phenolic laminated white sheet cover for mounting fitting like switches, sockets fan regulators etc. including 1.5 Sqmm single core (Green colour) PVC insulated unsheathed copper earth continuity conductor FRLS cable 1100 V grade as continuous earth wire for one light / fan / bell point controlled by one, one way switch. Note :- (i) The Switch / Socket accessories shall be measure and paid separately. (ii) The cost of MS sunken box & cover plate of size as required at site and cutting chases in stone / brick masonry and making good disturbed surfaces using CM 1:3 shall deemed to be included in quoted rate.

M&L for point wiring complete with 1.5 Sqmm single core (Phase - Red, Neutral - Black) PVC insulated and unsheathed multi stranded copper conductor FRLS cable of 1100 V grade PVC insulated and unsheathed cable inclosed in and including concealed PVC conduit 20 mm dia medium grade with all accessories ISI marked, including MS sunken box of thickness not less than 1.2 mm, cover with 3 mm thick phenolic laminated white sheet cover for mounting fitting like switches, sockets fan regulators etc. including 1.5 Sqmm single core (Green colour) PVC insulated unsheathed copper earth continuty conductor FRLS cable 1100 V grade as continuous earth wire for one light point controlled by two, 2-way switch. Note :- (i) The Switch / Socket accessories shall be measure and paid separately. (ii) The cost of MS sunken box & cover plate of size as required at site and cutting chases in stone / brick masonary and making good disturbed surfaces using CM 1:3 shall deemed to be included in quoted rate.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 Sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 Sqmm (Green), concealed in wall and drawn into and including rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in MS sunken box of thickness not less than 1.2 mm, cover with 3 mm thick phenolic laminated white sheet cover for mounting switches, sockets, fan regulator as required for one 3 pin socket outlet 5 Amps on the same board with other switches, complete all as specified and as directed.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 Sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 Sqmm (Green), concealed in wall and drawn into and including rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in MS Sunken box of thickness not less than 1.2 mm, cover with 3 mm thick phenolic laminated white sheet cover for mounting switches, sockets, fan regulator as required for 3 pin 5 Amps socket outlet on independent board, complete all as specified and directed. Note :- (i) The Switch / Socket accessories shall be measure and paid separately. (ii) The cost of MS sunken box & cover plate of size as required at site and cutting chases in stone / brick masonary and making good disturbed surfaces using CM 1:3 shall deemed to be included in quoted rate.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 2.5 Sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 2.5 Sqmm (Green), concealed in wall, drawn into and including rigid non metallic PVC conduit medium grade not less than 25 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in MS Sunken box of thickness not less than 1.2 mm, cover with 3 mm thick phenolic laminated white sheet cover for mounting switches, sockets, fan regulator as required for 3 Pin 15 Amps socket outlet on independent board, complete all as specified and directed. Note :- (i) The Switch / Socket accessories shall be measure and paid separately. (ii) The cost of MS sunken box & cover plate of size as required at site and cutting chases in stone / brick masonary and making good disturbed surfaces using CM 1:3 shall deemed to be included in quoted rate.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 4.0 Sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 4.0 Sqmm (Green), concealed in wall, drawn into and including rigid non metallic PVC conduit medium grade not less than 25 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in MS Sunken box of thickness not less than 1.2 mm, cover with 3 mm thick phenolic laminated white sheet cover for mounting switches, sockets, fan regulator as required for 3 Pin 15 Amps socket outlet on independent board, complete all as specified and directed. Note :- (i) The Switch / Socket accessories shall be measure and paid separately. (ii) The cost of MS sunken box & cover plate of size as required at site and cutting chases in stone / brick masonary and making good disturbed surfaces using CM 1:3 shall deemed to be included in quoted rate.

S&F LED lights fitting 1x20 W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

M&L for LED light fitting 1 x 9W / 10W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

M&L lamp holder, PVC / Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F Modular Switch one way 6 A, 1 module complete all as specified and directed.

S&F modular switch 1 way 16A, 1 module complete all as specified and directed.

S&F modular switch 2 way 6A, 1 module complete all as specified and directed.

S&F modular bell push 6A, 1 module complete all as specified and directed.

S & F Bell Ding Dong AC 230 volts, single pole complete all as specified and directed.

S & F Modular Socket, 6A - 2/3 pin combined, 2 module complete all as specified and directed.

S&F modular socket 6A/16A - 2/3 pin combined 2 module complete all as specified and directed.

S&F Fan step regulator, 120W - 2 module complete all as specified and directed.

S&F Socket outlet 2 in 1,flush type 3 pin, 6 and 16 amp complete all as specified and directed.

S&F socket outlet 2 in 1,3 pin, 6 Amp complete all as specified and directed.

S&F Isolator TPN 63 Amp 415 volt complete all as specified and directed.

S&F sheet metal enclosure with socket plug top and MCBs single pole and neutral enclosure with a two pin and earth plug and socket with one single pole MCB of capacity 20 Amps complete all as directed.

S&F sheet metal enclosure factory fabricated for MCB distribution board SPN double door type concealed in wall 240 Volt 8 way IP-42 protection with 200 amp rated bus bar complete all as specified and directed.

S&F sheet metal enclosure factory fabricated for MCB distribution board SPN double door type concealed in wall 240 Volt 12 way IP-42 protection with 200 amp rated bus bar complete all as specified and directed.

S&F sheet metal enclosure factory fabricated for MCB distribution board TPN double door type concealed in wall 415 volt 4 way IP-42 protection with 200 amp rated bus bar complete all as specified and directed.

S&F ceiling rose 3 phase, PVC / polycarbonate, isolated body complete all as specified and directed.

S&F ceiling fans, complete with three blade, down rod, accessories 230V, 1200mm sweep, with Squirrel cage induction motor complete all as specified and directed.

S&F exhaust fan, made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding of sweep of size 250mm complete all as specified and directed.

S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. complete all as specified and directed.

M&L for sub main wiring complete with 2 runs of 6 Sqmm single core PVC insulated unsheathed FRLS copper cable 1100 V grade with multistranded copper conductor ISI marked drawn through and including PVC rigid conduit / casing capping not less than 20mm and conduit accessories fixed on surface of wall / celing etc including provision of 1 Run of 6 Sqmm PVC insulated unsheathed FRLS cable with multistranded copper conductor as earth continuity complete all as specified and directed. Note : 02 Run of 06 Sqmm copper wire and 01 Run of 06 Sqmm copper earth wire along with PVC conduct shall be measured as one unit.

S&F amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SPN and 40 to 63 Amp current carrying capacity complete with connection testing and commissioning all as specified and directed.

S&F 415V 10KA 'B' curve miniature circuit breaker (MCB) of TPN / FP and 40 to 100 Amp current carrying capacity complete with connection testing and commissioning all as specified and directed.

S&F amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of Single Pole and 06 to 32 Amp current carrying capacity complete with connection testing and commissioning all as specified and directed.

Taking down and dismantling ceiling fan of any size including accessories of any type or make, safely and re-fixing after oiling, greasing and servicing in serviceable condition including provision of cable from ceiling rose or connector to fan including painting of fan by one coat of synthetic enamel paint of in white / off white colour by spraying including filling cavities with filler, after cleaning all dust etc. including writing Fan No. on each fan complete all as specified and directed.

S&F LED mirror light adjustable type 12 watt 230 volt single phase 6500K complete all as specified and directed.

Disconnecting and taking down Geyser and accessories of any type or make, safely and re-fixing after after minor repair like cleaning, tightening of loose component etc and servicing in serviceable condition including provision of cable from ceiling rose or connector to geyser including painting of geyser by two coat of synthetic enamel paint of in white / off white colour by spraying including filling cavities with filler, after cleaning all dust etc. including writing Geyser No. on each geyser complete all as specified and directed.

Taking down and dismantling exhaust fan of any size including accessories of any type or make, safely and re-fixing after throughly cleaning the bearing / bush, shaft, stator, rotor etc. & oiling, greasing and servicing in serviceable condition including provision of cable from ceiling rose or connector to fan including painting of fan by one coat of synthetic enamel paint of in white / off white colour by spraying including filling cavities with filler, after cleaning all dust etc. including writing Fan No. on each fan complete all as specified and directed.

S&F amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of Double Pole and 32 Amp current carrying capacity complete with connection testing and commissioning all as specified and directed.

S&F LED surface light 12W , 230 volt single phase, with opal diffuser and Lumen efficacy not less than 100 lm/W at 6500 K, complete all as specified and directed.

S&F T-Bulb, 10 Watt B22 LED (warm white / yellow) not less than 1000 lumen complete all as specified and directed. Make : Philips Cat Part No. 929001382713 or equivalent make of Wipro / Crompton / Havells as approved by GE.

M&L in repair LED Batten / Tubelight, (1.2m) 20 Watt made of CRCA sheet housing with PC gloss diffuser duly previewed connection having Luminous Flux not less than 2200 lumen, 6500 Kelvin complete all as specified and directed.

M&L in repair LED fixture of 10 Watt having luminous efficacy not less than 100 lumen/watt and including connection complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

Demolition of cement concrete un reinforced in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified and directed.

Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work (reinforcement cut as required to facilitate demolition) complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling of Plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

V S CONSTRUCTION (BID ID -3377519)

S.R.Enterprises (BID ID -3385162)