Repair and Maintenance of damaged staff bus stand, EGD Pipri

Engagement of beldar/ coolie/ helper for non measured work such as site clearance, cleaning of roof terrace & sun shed, uprooting of vegetations from the outer wall, dismantling existing plaster, rcc/ rb work & brick masonry work including disposal of refuse as directed by the Engineer-in-charge within a distance of 60 meters and other miscellaneous work as per direction of Engineer-in-charge. (SL. NO. CH1-02/ 03/ 13)

Engagement of sweeper for sewerage cleaning & disposal of the sludge as per direction of Engineer-in-charge. (SL. NO. CH1-42)

Cement concrete with cement, coarse sand and 4 cm gauge stone ballast in proportion of 1:6:12 in foundations & under floors including supply of all materials, labour and T&P etc. required for proper completion of the work. (SL. NO. 5.02)

1st class brick work in 1:6 cement and coarse sand mortar in super structure for wall of one brick thickness including supply of all materials, labour and T&P etc. required for proper completion of work. (SL. NO. 6.01+6.07+6.08)

Mild steel or iron work in heavy sizes such as built up gates, door, window & ventilator frames & grill, etc. wrought to required form including holes rivetting & welding where necessary and also fixing in proper position and alignment including cost of all materilas supplied by contractor. (SL. NO. 9.01)

12 mm thick plaster with cement mortar in proportion of 1:6 cement and coarse sand over brick work, minimum thickness not to be less than 10 mm including supply of all materials, labour and T&P etc. required for proper completion of work. (SL. NO. 11.09)

3 mm thick floating coat of neat cement finish including supply of all materials, labour and T&P etc. required for proper completion of the work. (Cement consumption 0.044 bag/Sqm) (SL. NO. 11.20)

2.5 cm thick 1:2:4 plain cement concrete floor with cement, approved coarse sand and 2 cm graded approved stone ballast laid in panels finished with 3 mm floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified and removing overlapping mortar at the joints of the panels if any and giving them a uniform finish without base concrete including supply of all materials, labour and T&P etc. required for proper completion of the work. (SL. NO. 12.02)

P/F precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. (Reference: DSR_Vol_1_2021, 12.50)

Hire Charges of tyre mounted excavator (JCB etc.) including cost of fuel along with Driver/Operator for site clearance as per direction of E/I. (SL. NO. CH2-21-h)

Hire charges of single phase portable welding set including cost of electrode along with the driver.

Painting new iron or wood work with one coat of ready mixed priming paint/wood primer and one coat of approved superior quality ready mix paint including supply of all materials, labour and T&P etc. required for proper completion of the work. (SL. NO. 13.01

Same as in above item but for the second coat after the first coat. (SL. NO. 13.02)

Painting 1st coat with APEX or equivalent brand weather coat paint on new wall surfaces (well prepared with Birla putty and one coat of primer ICI or equivalent which shall be paid separately) including through washing with water including cost of all materials, labour, T&P required for proper completion of work. (SL. NO. 13.22)

Same as above item but for the 2nd coat after the first coat. (SL. NO. 13.23)

Word Writing :- Letter of Size 5"

Word Writing :- Letter of Size 6"