GE 874/EWS-47/2021-22

Amount

B/R and E/M Portion

Demolition of cement concrete (un-reinforced) in ground floors and paving n.exc 15 cm thickness.

M&L Non - skid ceramic tiles 7 to 8 mm thick area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 sqm in floors set and jointed in neat cement slurry and pointed in while or coloured cement to mach over 25mm thick PCC 1:2:4 type B0 (using 12.5mm graded agg) and 15mm thick screed bed in Cement mortar 1:4.

M&L for Non - skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but notexceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 25mm thick PCC 1:2:4 type B0 (using 12.5mm graded agg) and 15mm thick screed bed in cement mortar 1:4.

M&L for Non - skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but notexceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 25mm thick PCC 1:2:4 type B0 (using 12.5mm graded agg) and 15mm thick screed bed in cement mortar 1:4.

Glazed ceramic Coloured tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tile complete all as specified and as directed.

M&L for green Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and as directed.

Dismantling of boarding, any description, fixed in any position with nails.

S&F 6mm Plywood, grade BWR, type BB, fixed with nails to timber frame work, fixed in wall, flat or sloping complete all as specified and directed.

All as per item 8 above but except boarding.

Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one faces, fixed with nails to timber frame work complete all as specified and as directed.

M & L plain fillet square, rectangular in section exc. 3 sqcm & n exc. 6 sqcm of second class softwood.

Dismantling plain or corrugated steel sheeting any gauge thickness in roof covering.

0.63mm thick galvanised corrugated mild steel sheeting with Zinc coating of 120 gms/Sqm with two corrugation side lap and at least 150 mm end lap , fixed with coach screws and washers in roof, walls etc, complete, all as specified.

All as per item No. 13 above but except sheeting.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified.

All as per item ser No 15 but plain sheet as in roof covering /cladding to wall fixed with tapping screws.

Brick work with sub- class ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and as directed.

M & L for rendering 15mm thick on stone masonry surfaces or other than fair faces of brick work or on one side of lathing in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and as directed.

M & L applying three coats of white washing including preparation of newly plastered surface of wall.

M & L applying two coats of cement base paint including preparation of newly plastered surface of wall.

M&L for Plain cement concrete 1:2:4 type B2 using 20 mm graded aggregate as in walls any thickness size or shape complete all as specified.

S&F 2nd class softwood clean swan batten at 30 cm centre to centre, of sectional area exc 5 Sqcm and not exc 15 Sqcm complete all as specified and directed.

Taking down chowkhats or frame exe. 1.5sqm and n.exc. 4 sqm each with shutter (without taking out shutter from the fame).

Taking down chowkhats or frame not exc 1.5 Sqm each ( without taking off shutters from the frame).

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, complete all as specified

Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face,with particle board complete all as specified

2nd class soft wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified.

30mm thick flush shutter solid core construction with block board core and plywood face panels commercial type on both sides complete all as specified and as directed.

Hacking out old broken glass (any thickness size quality or description) from wooden frame glazed with putty or wooden beads.

M & L sheet glass ordinary quality and glazing with oil putty in square n.exc 0.5 in each pane, 3mm thick complete all as specified and as directed.

S&F galvanised mild steel wire cloth .56mm nominal dia of wire and average width of aperture 1.18mm, fixed in repair all as specified.

M & L for applying two coats of synthetic enamel point over a coat of pink primer including preparation of new wooden surface exc 10 cm width or girths.

M&L preparation of old painted surfaces of wood and wood based surfaces of any description, not otherwise described, over 10cm width or girth, and applying one coat of synthetic enamel paint.

M& for one coat of synthetic enamel paint on old wooden surfaces including preparation of surfaces over 10 cm width or girth.

50mm thick PCC 1:3:6 Type C-1 (using 20mm graded crushed stone aggregates) laid in alternate bays (not exceeding 2 sqm each) as in plinth protection, finished even and smooth without using extra cement including filling the joint with mastic filling comprising 3 parts of sand & 1 part of heated bitumen 85/25 grade (by weight) all as specified.

S&F 15mm bore Bib taps cast copper alloy with crutch or butter-fly handle screwed down, screwed for iron pipe or for brass ferrules, complete all as specified and directed.

S & F in 15mm bore stop valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified.

M&L waste coupling of PTMT (half or full threaded) (Minimum weight 32mm-45gms) for 32mm bore dia of discharge pipe to WHB sink, fixed in repair, complete all as specified.

Tubular towel rail, 20mm dia, D type, 60cm long between flanges of brass CP and fixed with CP brass screws.

S&F PVC grating 100mm dia fixed to floor trap.

Mild steel pressed handle 100mm, oval type stove enamelled, black.

S&F MS butt hinges 100 mm long medium weight.

S&F MS butt hinges 75mm long medium weight.

S&F 125 mm long aluminium alloy, anodised barrel tower bolt of extruded section.

S&F 125 mm long Mild steel semi barre ltower bolt, riveted or spot welded type with plates, with brightbolt of extruded section.

Mild steel sliding door bolts 250mm long , plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed.

S&F tubing galvanized iron medium grade with all fitting laid in concealed, trenches, floors or fixed to walls or ceiling, in any length, bore of pipe 15mm.

S&F tubing galvanized iron medium grade with all fitting laid in concealed, trenches, floors or fixed to walls or ceiling, in any length, bore of pipe 20mm.

M & L for Vitreous china wash basin, vertically mounted fancy bowl flat back size 550 x 400 m including waste pipe and coupling 32mm for basins, etc. with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed including MS brackets& waste Pipe complete.

Vitreous china squatting pan (Orissa pattern) size 580 x 450 mm, white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor, fixed in repair, complete all as specified and directed.

Vitreous china bowl urinal size of 465X355X265mm white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws and pointing around urinal back in cement with bracket, flush pipe waste pipe grating and union for discharge pipe.

PVC valve less syphonic action type flushing cistern 10ltr capacity, low level/ high level white with inlet ball valve float and handle including brackets including 32mm dia PVC. flush pipe for low level cistern including all joints fixed in repair, complete all as specified.

Soap dish, vitreous China white, approximate size 160x 160x90mm.

S&F PVC connection 15mm dia and 600mm long with PTMT nuts and washer complete all as specified.

M & L for CP Pillar taps, with capstan head chromium plated 15 mm bore.

S&F PVC (SWR) floor trap 75mm dia outlet, plain with grating including jointing with solvent cement.

S&F PVC (SWR) Gully trap 110mm dia outlet, including jointing with solvent cement.

S&F PVC (SWR) P trap 100/110mm dia outlet, including jointing with solvent cement.

S&F PVC (SWR) Junction (Single T) 110mm dia, equal or unequal with access door including jointing with solvent cement.

S&F 75mm bore PVC (SWR) pipe single socket in any length with rubber ring jointed, fixed to wall complete all as specified.

S&F 110mm bore PVC (SWR) pipe single socket in any length with rubber ring jointed, fixed to wall complete all as specified.

S & F of 110mm dia PVC (SWR) bends of any radius complete.

20mm thick, second class soft wood boarding, planed one side, with butt joints and fixed with nails in facia, eaves boarding, complete, (except flooring and skirting) all as specified and directed.

S&F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm including waste coupling of PTMT (half or full threaded) (Minimum weight 32mm-45gms) for 32mm bore dia and LDPE waste pipe, fixed in repair, complete all as specified and directed.

M & L for chequered cement concrete tiles 25cm X 25cmX22mm thick set and jointed and pointed in neat cement slurry in floor with grey cement and pigment with and including cement screed 15mm thick in Cement Mortar (1:6) complete all as specified and directed.

M&L 75 mm thick PCC 1:3:6 type C-2, (using 40 mm graded aggregate) as sub base complete all as specified.

Lagging to pipes 15mm bore used in internal water supply or plumbing all round with 25mm thick bonded mineral wool preformed 'SNAP ON' pipe sections of density 144Kg/Cum conforming to IS-9842 provided with chicken mesh wire netting 25 gauge, 20mm mesh and covered with 0.01mm aluminium foil complete all as specified and directed.

M&L for 40mm thick PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in floor, finished even and smooth without using extra cement, complete all as specified and directed.

Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc.

M&L for preparation of new wall surfaces and applying two coats of cement based paint over a chalk whitening on wall surfaces.

M&L for one coat of primer and two coats of OBD including preparation of surface complete all as specified.

M&L for preparation of old steel surfaces and applying two coats of synthetic enamel paint on roof of any description over 10cm width or girth including preparation of old surface complete all as specified.

75 mm thick PCC (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection, surfaces finished even and fair using extra cement, complete all as specified and directed.

Wire netting of 20mm mesh size of stainless steel wire 1.4mm dia fixed with tinned tacks of stainless steel wire staples.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing) removing serviceable tile to store and rubbish off the premises complete all as specified and directed.

Excavation in post holes (or similar holes) each n.exc 0.5 cum, getting out, in any type of soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm thickness.

M&L for plain cement concrete 1:3:6 type C-2 (using 40mm graded stone agg) in foundations filling and mass concrete.

M&L for prepration of new steel surfaces of any description not otherwise described over 10cm width or girth applying two coats of synthetic enamel paint over a coat of red oxide primer all as directed by Engr-in-charge.

S&F Mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade st-240 including one shop coat of zink chromate primer paint including preparation of surface.

Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil.

Removing of excavated material exc. 250m but notexc 500m and depositing where directed at a level n exc. 1.5 m above the starting point all as specified and directed

M&L Rendering 15mm thick on fair faces of brick work or concrete surface, in cement mortar 1:4 finished the surface even and smooth without using extra cement, complete all as specified

M&L Hardcore of gauge exc. 63mm, n exc 100mm deposited, spread and levelled in layers n exc. 100mm thick, watered and rammed to a true surface of broken stone or boulders.

M&L for 100mm Cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in floors, paving and hardstanding, Finishing cement concrete surface even and fair complete all as specified and as directed.

M&L for 100mm Plain Cement concrete type D- 2, 1:4:8 using 40mm graded stone aggregate as in sub base complete all as specified.

Finishing surface of concrete roads, pavements by belting complete all as specified and as directed.

Forming 12mm thick Expansion joints for 100mm thick concrete filled with pre - formed bituminious filler and top 30mm primed and sealed with sealing compound, Grade A (thicknes of concrete slab 100mm) complete all as specified.

Forming construction (Dummy ) joints 65 mm deep x 10 mm wide, filled with sealing compound 'A' grade, complete all as specified and directed by Engr-in - charge.

Form work to edges of concrete flats, breaks in floors, openings in concrete walls. Floors, and roofs and RCC/PCC bands in walls, horizontal or sloping, and similar work exc. 10cm but n.exc. 20cm wide complete all as specified and directed by Engineer-in- charge.

M&L for Plastic dividing strips, 1.5 mm thick 22mm wide for floors.

Taking down copper/aluminium point wiring ( light fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc removing material to store for keeping in safe custody or for taking credit and making good distribued surface of wall, floor etc complete all as specified and directed.

Point wiring for one light point/Ex/fan point controlled by one switch with 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi strand cable and 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi stranded cable (green color) as earth lead in and including cable 1100 volts grade including 25mm casing and capping (ISI marked) for one light/ fan point controlled by one switch including CI/MS sunk box of required size, & as directed by Engr in Charge including 3mm thick plastic laminated top sheet cover, including cutting chases to wall and making good the disturbed surfaces to match with the existing specification complete all as specified.Make of wire: Finolex/Anchor/Polycab.

All as per description all as per item No. 93 here in before, but for 3 Pin socket outlet 5 Amps on the same board, with cable 1.5Sqmm size, insulated copper conductor cable 1100 volt grade with continuous PVC insulated copper conductor cable of 1.5 Sqmm, complete all as specified and directed.

Point wiring for 3 pin 5A socket outlet independent point controlled by one switch with 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi strand cable and 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi stranded cable (green color) as earth lead, 1100 volts grade including 25mm casing and capping (ISI marked) for one light/ fan point controlled by one switch including CI/MS sunk box of required size, & as directed by Engr in Charge including 3mm thick plastic laminated top sheet cover, including cutting chases to wall and making good the disturbed surfaces to match with the existing specification complete all as specified.Make : Finolex/Anchor/Polycab.

Point wiring for one 3 pin 15 Amps socket outlet/sheet metal enclosure independent with 2.50 sqmm PVC insulated un-sheathed copper conductor single core multi strand cable and 1.5 sqmm PVC insulated un-sheathed copper conductor single core cable (green color) as earth lead in and including 25mm PVC caping casing medium grade with all fittings (ISI Marked) controlled by one switch including CI/MS sunk box of required size, & as directed by Engr in Charge including 3mm thick plastic laminated top sheet cover, including cutting chases to wall and making good the disturbed surfaces to match with the existing specification complete all as specified.Make : Finolex/Anchor/Polycab.

Supply and fixing of lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings suitable for LED bulb 7 watt. Make : Havells/Anchor/Siska/Philips/Bajaj

Supply and LED 7 Watt Bulb with B22 pin, of make Havells/ Syska/ Philips, suitable for fixing in holder as above.

S&F for decorative LED batten for surface and pendant applications. Anodized extruded aluminium housing, high transmisitivity diffuser, high lumen output of VIVA MINI LED Luminaires (4FT) of 20W connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed. Make-Havells product code LUMILINEPLUSBS20WLED865SPCSS or equivalent of approved make as approved by Engr-in-Charge

Supply and fixing LED light fitting, 1x9 W bulk head luminaries, with lamp holders, etc. complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V, 50 HZ. Make : Bajaj/Havells/Anchor/Philips

S&F modular type Switch piano 6 Amps single pole one way. Make : Havells/Anchor/Philips

S&F ceiling rose surface bakelite 65x50mm two to three terminals (ISI Marked). Make : Havells/Anchor/Philips

S&F socket outlet 2-in-1, 3 pin, 6 Amps modular type (ISI Marked) complete all as specified and as directed by Engr-in-charge. Make : Havells/Anchor/Philips

S&F Switch socket combination 2-in-1 5 pin 6 Amps modular type (ISI Marked) complete all as specified and as directed by Engr-in-charge. Make : Havells/Anchor/Philips

S&F Switch socket combination 5 in 1, 5 and 15 Amp modular type universal controlled by by one switch (ISI Marked). Make : Havells/Anchor/Philips

S&F rectangular wooden boards/ blocks 30x25x4cm depth closed recessed, complete all as specified and as directed by Engr-in -charge.

S&F RCBO, four pole Three phase and Neutral 420 Volts , 50 H 32-63 Amps, 300mA all as specified and as directed.

Supply & Fixing RCBO, single phase and neutral 300mA, 420V , 32 - 63Amp all as specified and directed. Make- Havelles/MDS/Legrand.

S&F Sheet metal enclosure factory made for DBs Triple pole and neutral Single door 415 volts 4 way with 200 Amps rated bus bar fixed on walls, including dressing and connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning and making good of wall, surfaces all as specified and directed. Make : Havells/lEGRAND/SSK.

S&F Sheet metal enclosure factory made for DBs single pole and neutral double door 240 volts 8 ways with 200 Amps rated bus bar fixed on walls, including dressing and connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning and making good of wall, surfaces all as specified and directed. Make : Havells/LEGRAND/SSK.

S&F Sheet metal enclosure factory made for DBs single pole and neutral double door 240 volts 16 way with 200 Amps rated bus bar fixed on walls, including dressing and connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning and making good of wall, surfaces all as specified and directed. Make : Havells/lEGRAND/SSK.

Supply and fixing 415V 10KA 'C' curve miniature circuit breaker (MCB) of TPN 40-100 Amp and current carrying capacity in the DB complete with connection testing and commissioning all as specified and directed by Engr-in-Charge. Make : Havells/EGRAND/SSK

S&F Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of Single Pole and Neutal (SPN) 32-63 Amp and current carrying capacity in the MCB DB complete with connection testing and commissioning.. Make : Havells/Legrand/Philips

S&F Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of Single Pole 5 to 32 Amp and current carrying capacity in the MCB DB complete with connection testing and commissioning.. Make : Havells/Legrand/Philips

S&F Three phase Voltage and current protection relay of protection from over current as well as over voltage and auto adjustable complete with connecting testing and commissioning. All as specified and directed by Engr-in-Charge

S&F Single phase Voltage protection relay of trip setting 85 to 500 V AC complete with connecting testing and commissioning. All as specified and directed by Engr-in-Charge

S&F house service bracket (hook type) complete with 3.0m long G.I. pipe 40mm dia Med. grade, two nos 90 degree bends. M.S. hook and stay or guy complete all as specified and as directed by Engr-in-Charge.

Supply and fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 4 Core 16 sq. mm nominal cross section in service connections.

S&F 1100 volt grade heavy duty cable PVC insulated multistranded aluminum stranded conductor served with PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 mtr apart including 4mm dia GI suspension wire one twin core cable flat of circular of size 16 Sqmm complete all as specified and as directed by Engr-in-Charge. Make : Havells/Anchor/Polycab/Plaza

M & L for sub main wiring with two single core 6 sqmm PVC insulated and unsheathed 1100 volts grade, stranded copper conductor FRLS ISI marked drawn into & including medium grade PVC conduit/ casing caping, with wooden or white colour casing caping (as specified and directed) 25 mm dia with all fittings and accessories and one continuous run of 4 sqmm copper conductor PVC insulated (green colour) as earth wire fixed into PVC casing / conduit (not less than 25mm outer dia) with all fittings and accessories fixed conealed/ surface including taking down old unserviceable submain wiring and making good disturbe surface complete all as specified and directed.Make of cable- Havells ,Plaza, Policab.Make of Casing Caping - Poly plast/ pressfit/ Presto plast.

Earthing complete with galvanized steel earth plate electrode 60cmx 60cmx6.3mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanized iron wire 4.0mm dia by means of bolts, nuts and washers of galvanized iron or steel, protected by GI light grade pipe 15mm bore including GI light grade water pipe 20mm dia with funnel all as shown in electric plate No. 03 of 2009 SSR Pt-I and testing on complete including earth work in any type of soil, PCC 1:2:4 type B-0 as in earth pit and cover 40mm thick reinforced with XPM (weight not less than 4.0Kg/Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia MS bar handle made to shape, common salt, charcoal and testing on completion, all as specified and directed.

S&F in replacement irragular voltage, voltage stabilizer for automatic operation, single phase and neutral air cooled indoor type & designated for input variation between 90V to 290V with output voltage stabilizer at 230 V with accuracy +/- 2.5% 4-6 Sec initial delay and of capacity 10 KVA complete all as specified and directed by Engr-in-Charge of Make V Guard or Equivalent as approved by Engr-in-Charge

S&F in replacement irragular voltage, voltage stabilizer for automatic operation, single phase and neutral air cooled indoor type & designated for input variation between 90V to 290V with output voltage stabilizer at 230 V with accuracy +/- 2.5% 4-6 Sec initial delay and of capacity 15 KVA complete all as specified and as directed by Engr-in-Charge of Make V Guard or Equivalent as approved by Engr-in-Charge.

M/S AK CONSTRUCTION

MS SHEIKH NADEEM AKBAR

Javeed And Co

M/S MOHAMMAD JAMAL WANI

M/S FAYAZ CONSTRUCTIONS

M/S AB AHAD RATHER

Bidder Name

M/S MOHAMMAD JAMAL WANI

M/S AB AHAD RATHER

M/S FAYAZ CONSTRUCTIONS

Javeed And Co

M/S GM CONSTRUCTIONS

M/S AK CONSTRUCTION

MS SHEIKH NADEEM AKBAR