PROVN OF CONSTR OF 01 X TOILETS AND BATHROOMS IN QTR GD PREMISES OF 155 INF BN (TA) JAK RIF AT NAYA RAIPUR MIL STN

Amount

Surface dressing n exc 15 cm deep and getting out in soft /loose soil complete all as specified and as directed.

Excavation in trenches not exc 1.5 m wide and n.exc 1.5m in depth for foundations soft/loose soil complete all as specified and as directed.

Returning , filling in spreading and levelling and well ramming in layers not exc 25cm including watering for filling under floor complete all as specified and as directed.

Removing of excavated material (soils, etc) to distance n.exc 50 M and depositing where directed at a level n.exc 1.50m above the starting point complete all as specified and as directed

M & L for moorum/red bajri filling in floors or pavings laid in layers n exc 15 Cm thick spread levelled and rammed including watering etc complete all as specified and as directed.

M & L for sand filling under floors or in foundations spread levelled and rammed including watering etc complete all as specified and as directed.

M & L broken brick hardcore of gauge n exc 63 mm deposited, spread and levelled in layers n. Exc 15 cm thick watered and rammed to true surface.complete all as specified and as directed.

M & L for PCC (1:5:10) type D2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified.

M & L for reinforced cement concrete Type (Nominal mix)A1 1:11/2:3 (using 20mm graded stone aggregate)as in foundation including rafts,f ooting, foundation beams, plinth beams, bases for columns, etc and mass concrete complete all as specified and as directed.

M & L reinforced cement concrete (Nominal mix)A1 1:11/2:3 (using 20mm graded stone aggregate) as in Columns, pillars, piers, posts and struts complete all as specified and directed.

M & L reinforced cement concrete(Nominal mix)A1 1:11/2:3 (using 20mm graded stone aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M & L for (Nominal mix) A1 1:11/2:3 (using 20mm graded stone aggregate) as in slabs supported on walls etc complete all as specified and as directed.

M & L for use and waste of formwork to Square,rectangular or polygonal rough surface of concrete of sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and as directed.

M & L for use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and as directed.

M & L for use and waste of formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed.

M & L for use and waste of Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or sloping) complete all as specified and directed.

M & L for use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and as directed.

M & L for brick work with modular size fly ash bricks straight or curved on plan to any radius in half brick thick wall built in CM (1:4) complete all as specified and as directed.

M & L mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spiarally for hooping for columns, plinth beam etc, hooking ends and binding with and including mild steel wire(annealed) not less than 0.9mm dia.complete all as specified and directed.

M & L for mild steel TMT bars 5 mm dia and over upto including 10mm dia in stirrups, spacers and binder complete all as specified and directed.

M & L brick work built in CM 1:4 using fly ash modular bricks straight or curved on plan exc 6m mean radius complete all as specified and directed

M & L damp proof coarses in cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) 40mm thick including necessary form work complete all as specified.

M & L for 75mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in sub floor to receive any type of floor finish, tiles etc complete all as specified and as directed.

M & L for 25mm thick PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in sub floor to receive any type of floor finish, tiles etc complete all as specified and as directed.

M & L 75 mm thick PCC as in plinth protection and path type C-2 1:3:6 (20 mm graded agg) finishing cement surfaces even and smooth with out using extra cement complete all as specified and as directed.

M & L rendering 10mm thick plaster in CM 1:6 on brick or concrete surfaces complete all as specified and as directed.

M & L 15mm thick rendering on fair faces of brick or concrete surface in Cm (1:4) and providing in two layers, with WPC @ 3% of cement and finishing even and smooth without using extra cement complete all as specified and as directed.

M & L rendering 5 mm th in CM 1:3 as in ceiling complete all as specified and as directed. .

M & L non skid coloured ceramic tiles 7 to 8 mm thick(square/rectangular) area of each tiles exceeding 0.06 sqm but n.exc 0.11sqm in floor etc,over 15 mm thick screed bed in CM(1:6),set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces complete all as specified and directed.

M & L glazed ceramic coloured tiles in vertical surface 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match. complete all as spd & directed incl rendering 10mm thick in CM (1:4) and finished rough complete all as specified and as directed.

M & L for two coat of oil bound emulsion distemper incl prepration of new plastered surface of wall over a coat of primer complete all as specified and as directed.

M & L for three coat of white washing on ceiling including preparation of surfaces complete all as specified and as directed.

M & L Preparation of new plastered surfaces of wall and applying two coats of cement base paint over one coat of alkali resistant primer complete all as specified and as directed.

Supply only integral water proofing compound complete all as specified and as directed.

S & F Vitreous China cascade type wash down water closet pan(pedestal pattern), white with soft seat cover,fixing accessories incl cistern fitting , flushing cistern and flush pipe "P" or "S" trap etc. all as specified and as directed.

S & F 10 Ltr PVC valveless, syphonic action type flushing cystern low level with inlet, ball valve, float and handle including brackets and PVC out let sutaible for IWC complete all as specified and as directed.

S & F for vitrious china wash basin, white size 600x400x185 mm counter type as per catalouge,SLS-WHT-6601 Make- Jaquar or equivalent series in hindware or parryware complete fixed in counter opening of granite platform and supported over bracket etc. including cutting for and pinning in ends of brackets or errecting bracket and 32mm dia waste fitting brass chromium plated etc;with long screwed shanks and fly nuts,flange end bedded in red lead cement including bottle trap fitted complete all as specified and directed.

S & F 15 mm fancy type pillar taps chromium plated cast copper alloy with capstan heads screwed down high pressure with or without lettered ‘Hot’ or ‘cold’ with long screwed shanks and fly nuts all as specified and directed by Engr-in-charge.

S & F 15 mm fancy/concealed type stop valve cast copper alloy chromium plated screwed high pressure with crutch or butter fly handle screwed both ends for iron or union and fixed to 15 mm GI tube complete all as specified and as directed.

S & F Bib taps cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down ,screwed for iron pipe or or brass ferrule for 15 mm bore of pipe complete all as specified and as directed..

S & F 15 mm stop valve/angle cock, cast copper alloy chromium plated fancy type screwed high pressure with crutch or butter fly handle screwed both ends for iron or union and fixed to 15 mm GI tube complete all as specified and directed by Engineer-in-Charge.

M & L brass chromium plated tubular towel rail 20mm dia D type 600 mm long between flanges fixed Complete all as specified and directed.

S & F PVC connection pipe 45 cm long with PTMT fixed to WHB, flushing cistern an complete all as specified and as directed.

S & F for Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed.

S & F Toilet paper holder of chromium plated fixed to walls with chromium plated (CP) brass screws complete and all as specified and directed.

S & F shower rose 125 mm brass chromium plated with swivel joints complete and all as specified and directed.

S & F PVC colour health faucet complete all as specified and as directed.

S & F glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm complete all as specified and as directed.

S & F Vitreous China Urinal, Half Stall type White (excluding flushing cistern, flush pipe and waste pipe) and fixing complete all as specified and direcetd.

Cutting chases ,pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landing ,steps cills, sunshades, shelves ,lintels etc. and cutting chases for concealed water tubing or concealed conduit wiring etc. and making good ,cutting not exc. 10 cms girth complete in brick walls complete all as specified and as directed.

S & F GI tubing medium grade with all fitting and fixed to wall ,ceiling or laid in floor etc complete of 15 mm bore pipe complete all as specified and as directed.

Ditto - all as per above item No 52 but 20 mm bore

S & F 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed to 20mm dia GI tube complete all as specified and as directed.

S & F rotational moulded polethylene water tank of 1000 ltrs capacity ( cylindrical vertical with closed top) hoisted and fixed in position all as pacific SSR Part- I complete all as specified and directed.

S & F PVC(SWR)75mm borepipes single socketed in any length with rubber ring joints fixed to walls/floor all as specified and directed.

Ditto all as per above items No 56 but 110mm

PVC (SWR)bend 110mm bore, complete all as specified and directed

PVC (SWR)bend 75mm bore, complete all as specified and directed

Supply and laying double wall corrugated DWC pipe HDPE pipe of outer dia 150mm of approved make ISI marked polythene with smooth internal wall & profiles external surfaces for non pressure for sewage complete all as specified and as directed.

Supply and fixed PVC (SWR) vent cowl, 110mm dia

M & L concrete bed to drain pipe including packing under and haunching against the side and pipe of 150mm bore in cement concrete 1:3:6 type C2 after they laid and tested.

S & F Grating doom 125 mm dia with waste hole of PTMT Minimum weight 40 gms complete all as specified and directed.

S & F 75mm PVC (SWR) floor trap(S/P), plain with grating including jointing with solvent cement

S & F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall pipe complete all as specified and directed.

S & F 110mm PVC soil waste and vent pipes in any length with or with out ears with cement joints , fixed to wall complete all as spd

S & F 110 mm bore bends PVC (any radius) with oval access doors ISI marked complete all as spd

S & F solid PVC door frame of size 50mmx47mm thick made out of 5mm thick plain colour PVC sheet reinforced with M.S Sqare tube, single side prelam PVC sheet used instead of plain colour PVC sheet edges will be painted to match with prelam sheet.

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S tubes for top and bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail, and bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles beading, and joined to gether with solvent cement, suppling and fixing in the frame at site as per specification and drawing.

S & F Anodised aliminium window and ventilators shutters, side hung type ithout sash bars, aluminium sections weighing 0.55kg/m including necessary joining cleats, glazing clips rubber packing anodised aliminium snap beading screws anodised aluminiumfitting such as peg stays 150mm long(1no)hinges type B-21 100mm long (2no) hinges type B-21 100mm long (2no) suitable handles(1no) complete all as specified and as directed.

S & F 100 mm long aluminum anodized barrel tower bolt extruded section.

S & F aluminum handles cast type anodize 150 mm long.

S & F extruded aluminium alloy butt hinges 125 mm size type B-21 all as specified & directed.

S & F curtain rods of anodised aluminium alloy with fixing brackets , stops, roller etc in repairs.

S & F galvanised steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm in repairs complete all as directed at site.

S & F figured glass ordinary quality and glazing with oil putty in square n.exc 0.5 Sqm in each pane thickness of glass 3mm thick all as directed at site

S & F in MS sliding door bolts 200mm long plate type stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bold plate and two on staple plate and fixed complete all as specified and directed.

M & L rendering 10 mm thick in CM 1:3 , mixed with water proofing compound, on concrete surfaces of roof , surface finished even and smooth. Note :- supply only of water proofing compound shall be measured and paid seperately.

M & L for cleaning the top surface of concrete and providing APP based polymeric membrane minimum weighing 3kg/sqm of approved make for water proofing treatment test to be carried out from national test house/Govt lab , including priming the surface by applying bituminous primer @ 0.3 Kg/sqm and applying the surface by blown grade bitumen 85/25 @ 1.20 Kg/Sqm & applying water proofing memberane(with minimum 10 cm. overlaps) and applying the surface by blown grade bitumen 85/25 @ 1.20 Kg/Sqm and applying two coats of aluminium paint complete all as specified & directed.

M & L for 75mm thick PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub floor to receive any type of floor finish, tiles etc complete all as specified.

M & L for coloured machine pressed rubber moulded precast concrete interlocking paver blocks any shape and any size conforming to IS15658-2006 of 60mm thickness, M-35 grade complete all as specified and directed

M & L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line,level and curvature ,jointed with cement mortar 1:3 including making joints with or without grooves(thickness of joints except at sharp curve shall not to more than 5 mm),including making drainage openinf wherever required complete as specified and directed by engineer in charge.

M & L for point wiring using approved colour coding as per IS, with stranded copper conductor 1.5 sqmm (nominal area), single core, flame retardant low smoke(FRLS), PVC insulated and unsheathed cable 1100 volts grade, ISI 694 marked TEC and FIA approved in and including PVC conduit pipe and its fittings ISI marked, with mild steel sunken boxes suitable for modular/normal switch/sockets etc with earth dolly duly painted with two coats of anti corrosive paint over a coat of red oxide primer internally, incl covered with suitable module cover plate with frame including flame retardant low smoke (FRLS) PVC insulated unsheathed stranded copper conductor 1.5 sqmm (nominal are) single core cable as earth continuity conductor to common earth and connected to earth dolly for One light/ Bell point controlled by one switch complete all as specified and directed

Ditto- all as per item No 83.00 herein before but One socket out let 3 pin 5 Amp on same board.

S & F modular switch 1 way 6A 1 module complete all as specified and directed. Make : Legrand/ Crab tree/ Philips,

S & F modular socket 6A 2/3 Pin combined 2 module complete all as specified and directed. Make : Legrand/ Crab tree/ Philips.

S & F modular white cover plate and frame 2 module,complete all as specified and directed.

S & F modular white cover plate and frame 8 module,complete all as specified and directed.

S & F for ceiling rose 3 phase/PVC/polycarbonated isolated body complete all as specified and directed

S & F Modular flush box 2 module complete all as specified and directed.

S & F Modular flush box 8 module complete all as specified and directed.

Supply and fixing LED lights fitting 1x 18W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. Make Havells/Bajaj/Phillips/Wipro

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed

S & F for MCB DB's 4 Way SPN, 240 volts for mounting MCBs/RCBO's ELCB's etc. as per IS specification of factory made fabricated out of CRCA sheet 1.2 mm thick powder coated fitted with DIN Channel neutral link and 200 Amps rated bus bar.The DB's shall single door type . Inner door fixed on spring loaded hinges with locking arrangement & outer door openable hinged with locking arrangement having IP-43 protection, complete all as specified and directed

S & F for MCB SPN 32 Amps 240 Volts C Curve 10 KA, complete all as specified and directed.

S & F for MCB SP 6-32 Amps 240 Volts C Curve 10 KA, complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode of size 60cm X 60cm X 6mm buried directly in ground (earth pit not less than 2.25 metres deep below the normal ground level) with top edge of the plate not less than 1.5m below normal GL connected to GI earth wire 4 mm dia by means of GI bolts, nuts, check nuts and washers and earth strip protected by 25 mm dia GI pipe medium grade and connected to main distribution board/earthing test point all as shown on electrical plate No.3 of SSR Part I and all as specified including testing on completion.Notes: The unit rate shall also include for excavation, earth work in hard/dense soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix, type B1 cover reinforced with 8mm dia TMT bars @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh, protection pipe for earth lead upto 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II and also refer Plate No-03. Earth strip and protection pipe beyond 7.5m shall be measured and paid separately. Note :- Earthing will be redone if desied erath result not found during testing of the same at site,complete all as specified and directed

Supply, laying and connecting XLPE insulated armoured heavy duty electric cable 16 sqmm 2 core with aluminum conductor 1100 volts grade cross sectional area laid in ducts/wall/cable tray/trenches with suitable size of cable glands, crimping type cable lugs, connecting to existing MCCBs in panels all as specified.

Supply and spreading clean and dry fine sand free from sharp material (unwashed) laying in trenches 8 cm thick before laying and 15mm thick after laying around the cable for cushioning teting, all as specified and directed by engg in charge.

Supplying and laying un-reinforced precast concrete cable cover, class LV,type 1 with peak, size 250mm x 150mm x 40mm complete , all as specified and directed by engr-in-charge.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm Sweep complete all as specified and directed

Material and labour GI tubing 25 mm dia medium grade galvanised with all fittings laid in trenches complete all as specified and directed by engg in charge. Make : Tata Jindal/ Swastik

Supply and fix 25 mm bore gun-metal gate bulve with brass insert iron wheel head screwed both ends for iron pipe all as directed.

Cutting existing steel tubing for alteration of addition (each cut measured) and Screwing existing steel tubing for alterations or additions (or lengthening screw on pipe to form connector) if necessarily done in position without taking down bore of pipe 50 mm, complete all as specified and directed

Total contract sum shall be calculated after deduction of schedule of credit amount of Rs. Nil

M/S INDIA ENTERPRISES (BID ID -3458093)