Design, Supply, Erection, Testing, Commissioning of 11KV CSS, DTs, associated RMUs, Pillar boxes, HT/LT cables, its terminations and all civil works under EPC mode in Puducherry under SMARTCITY project by PSCDL through PED

Design, Manufacture, Factory testing, Supply and delivery of the following equipments/ item of materials as per the Tender Technical specification. In view of space constraints only abstract of items are listed below. Therefore the Bidder should read the description of each items as detailed in the BOQ listed in Section-VI of Tender specifications before quoting. Rate should be quoted along with GST No. and prescribed rate of GST.

Design, Supply and delivery of 11kV, 630KVA, Outdoor Compact Sub- Station (in compliance of IEC 62271-202) consisting of the following :- i) HT SWITCH GEARS:- 11kV 630Amps 21kA for 3 sec. SF6 insulated Copper Busbar Non-Extensible Ring Main Unit (Type CVC) consisting of Two Nos. of remote operated motorised Load Break Switches and One No. of Fixed remotely motorised operated vacuum Circuit Breaker unit. ii) TRANSFORMER:- Three Phase, 50 Hz, Core type, two winding, 630 KVA 11KV/433V DYn11 cast resin dry type, AN type Distribution Transformer. iii) LT PANEL:- 433 LT Indoor panel with 1000Amps Al Bus bar 100% for phase and 50% for Neutral, complete with internal wiring consisting of following:- (A) LT Incomer from Transformer:-1000 Amps 433V 4P 50Hz 50KA remote wireless signal based electrically operated Type Air Circuit Breaker (ACB) & (B ) LT Out Going:- (a) 400 Amps 433V 3P 50Hz 36KA, TPN MCCB - 4 nos. (b) 125 Amps 433V 3P 50Hz 36KA, TPN MCCB - 2 nos. iv) OUTDOOR ENCLOSURE:- Outdoor type enclosure having construction of Galvanised Sheet Steel of thickness minimum 2mm & . Base plate should be 4mm thick. The Enclosure shall have IP54 degree of protection. v) Interconnection & Earthing:- Interconnection Between HT switchgear & Transformer. Interconnection between Transformer & LT switchgear. Internal earthing connections by using GI Strips. vi) SCADA SYSTEM:- Equipped with SCADA system having all hardware like FRTU, power supply, analog and digital I/O devices, battery, charger, software, modems, antenna, sensors, transducers, control wiring, etc

Design, Supply and delivery of 11kV, 315KVA, Outdoor Compact Sub- Station (in compliance of IEC 62271-202) consisting of the following :- i) HT SWITCH GEARS:- 11kV 630Amps 21kA for 3 sec. SF6 insulated Copper Busbar Non-Extensible Ring Main Unit (Type CVC) consisting of Two Nos. of remote operated motorised Load Break Switches and One No. of Fixed remotely motorised operated vacuum Circuit Breaker unit. ii) TRANSFORMER:- Three Phase, 50 Hz, Core type, two winding, 315 KVA 11KV/433V DYn11 cast resin dry type, AN type Distribution Transformer. iii) LT PANEL:- 433V LT Indoor panel with 1000 Amps Al. Busbars 100% for Phase and 50% for Neutral , complete with internal wiring consisting of following:- (A) LT Incomer from Transformer:-1000 Amps 433V 4P 50Hz 50KA remote wireless signal based electrically operated Type Air Circuit Breaker (ACB) & (B ) LT Out Going:- (a)400 Amps 433V 3P 50Hz 36KA, TPN MCCB - 2 nos. (b) 125 Amps 433V 3P 50Hz 36KA, TPN MCCB - 2 nos. iv) OUTDOOR ENCLOSURE:- Outdoor type enclosure having construction of Galvanised Sheet Steel of thickness minimum2mm & . Base plate should be 4mm thick. The Enclosure shall have IP54 degree of protection. v) Interconnection & Earthing:- Interconnection Between HT switchgear & Transformer. Interconnection between Transformer & LT switchgear. Internal earthing connections by using GI Strips. vi) SCADA SYSTEM:- Equipped with SCADA system having all hardware like FRTU, power supply, analog and digital I/O devices, battery, charger, software, modems, antenna, sensors, transducers, control wiring, etc

Design, Supply and delivery of Three Phase, 50 Hz, Core type, two winding, 630 KVA 11KV/433V DYn11 cast resin dry type, AN type Distribution Transformer.

Design, Supply and delivery of Three Phase, 50 Hz, Core type, two winding, 315 KVA 11KV/433V DYn11 cast resin dry type, AN type Distribution Transformer.

Design, Supply and delivery 315 kVA, 11/0.433 KV, 3 phase, OIL Immersed, Air Natural (ONAN) Energy Efficient, Level 2, Distribution Transformers.

Design, Supply and delivery of 11 KV, 3 Pole, Modular extensible type outdoor SCADA compatible SF6 insulated Ring main units comprising of 3 Way Ring Main Units with 1 Potential Transformer and 1 FRTU and MODEM (2 Nos of Load break switch and 1 No of Circuit Breaker) and allied accessories.

Design, Supply and delivery of 11 KV, 3 Pole, Modular extensible type outdoor SCADA compatible SF6 insulated Ring main units comprising of 4 Way Ring Main Units with 1 Potential Transformer and 1 FRTU and MODEM (3 Nos of Load break switch and 1 No of Circuit Breaker) and allied accessories.

Design, Supply and delivery of 11 KV, 3 Pole, Modular extensible type outdoor SCADA compatible SF6 insulated Ring main units comprising of 4 Way Ring Main Units with 1 Potential Transformer and 1 FRTU and MODEM (4 Nos of Load break switches) and allied accessories.

Design, Supply and delivery of 11 KV, 3 Pole, Modular extensible type outdoor SCADA compatible SF6 insulated Ring main units comprising of 5 Way Ring Main Units with 1 Potential Transformer and 1 FRTU and MODEM (2 Nos of Load break switch and 3 No of Circuit breaker) and allied accessories.

Design, Supply and delivery of 11 KV, 3 Pole, Modular extensible type outdoor SCADA compatible SF6 insulated Ring main units comprising of 5 Way Ring Main Units with 1 Potential Transformer and 1 FRTU and MODEM (4 Nos of Load break switch and 1 No of Circuit breaker) and allied accessories.

Design, Supply and delivery of 11 KV, 3 Pole, Modular extensible type outdoor SCADA compatible SF6 insulated Ring main units comprising of 5 Way Ring Main Units with 2 Potential Transformer and 2 FRTU and 2 MODEM (2 Nos of Load break switch & 1 PT, FRTU and Modem +1No of Buscoupler switch+ 2 Nos of Load break switch & 1 PT, FRTU and Modem ) and allied accessories.

Design, Supply and delivery of 11 KV, 3 Pole, Modular extensible type outdoor SCADA compatible SF6 insulated Ring main units comprising of 6 Way Ring Main Units with 1 Potential Transformer and 1 FRTU and MODEM (4 Nos of Load break switch and 2 Nos of Circuit breaker) and allied accessories.

Design, Supply and delivery of 11 KV, 3 Pole, Modular extensible type outdoor SCADA compatible SF6 insulated Ring main units comprising of 8 Way Ring Main Units with 2 Potential Transformer and 2 FRTU and 2 MODEM (1 No. of Load break switch and 1 No. of Circuit breaker & 1 PT, FRTU and Modem +1No of Buscoupler switch+ 2 Nos of Load break switch and 3 Nos of Circuit breaker & 1 PT, FRTU and Modem) and allied accessories.

Supply and delivery of Lucy Electric Make 11 KV, 3 Pole, Modular extensible type outdoor SCADA compatible SF6 insulated Ring main units comprising of 2 Way Ring Main Units with 1 No of Bus coupler switch and 1 Potential Transformer &, FRTU and Modem ( 2 Nos of Load Break switch and 1 No of Bus coupler switch) for coupling with the existing Lucy Electric Make 11KV RMUs.

Supply and delivery of 3 core 95 sq.mm XLPE insulated Armoured Screened Type 11KV Al UG cable for interconnections between RMUs and DTs with in the RMS yards.

Supply and delivery of 400 Sqmm XLPE Insulated (HEAVY DUTY) Armoured PVC Sheathed 3 ½ core 1100V Al UG cable for connecting the DT LT side with SS pillar Boxes in the yard and arround it.

Supply and delivery of 300 Sqmm XLPE Insulated (HEAVY DUTY) Armoured PVC Sheathed 3 ½ core 1100V Al UG cable for connecting CSS DT LT side 400 amps MCCB with the existing LT feeder cables after removing the existing SS pillar Boxes in the yard and around it.

Supply and delivery of 150 Sqmm XLPE Insulated (HEAVY DUTY) Armoured PVC Sheathed 3 ½ core 1100V Al UG cable for connecting CSS DT LT side 125 amps MCCB with the existing LT feeder cables after removing the existing SS pillar Boxes in the yard and around it.

Supply and delivery of heat shrinkable end termination suitable for 3 core 400 sq.mm XLPE insulated Armoured Screened Type 11KV Al UG cable for termination at various RMUs at various proposed 11KV RMS yards.

Supply and delivery of heat shrinkable indoor end termination suitable for 3 core 95 sq.mm XLPE insulated Armoured Screened Type 11KV Al UG cable for providing termination at the proposed RMU side Circuit Breakers.

Supply and delivery of heat shrinkable Boot type indoor end termination suitable for 3 core 95 sq.mm XLPE insulated Armoured Screened Type 11KV Al UG cable for providing termination at the proposed DT's HT side.

Supply and delivery of heat shrinkable type outdoor end termination suitable for 3 core 95 sq.mm XLPE insulated Armoured Screened Type 11KV Al UG cable for providing termination at the proposed DT's HT side.

Supply and delivery of heat shrinkable outdoor end termination suitable for 3 core 400 sq.mm XLPE insulated Armoured Screened Type 11KV Al UG cable for providing termination at Marapalam SS end take off points.

Supply and delivery of 300 to 300&400 sqmm straight through joint for connecting the new 400sqmm XLPE Insulated (HEAVY DUTY) Armoured PVC Sheathed 3 ½ core 1100V Al UG cable. from CSS's DT's LT side 400Amps MCCB to the existing feeder UG cables (Mostly of 300& 400 sqmm dia cables)after removing the existing SS pillar Boxes in the yard and around it.

Supply and delivery of 150 to 150 sqmm straight through joint for connecting the new 150sqmm XLPE Insulated (HEAVY DUTY) Armoured PVC Sheathed 3 ½ core 1100V Al UG cable. from CSS's DT's LT side 125Amps MCCB to the existing feeder UG cables after removing the existing SS pillar Boxes in the yard and around it.

Design, Supply and delivery of 800Amps 6 way SS Pillar boxes with 600/5A CTs (4 nos including neutral CT for each pillar box) interconnections.

Supply and delivery of FRP Type metering marshaling box suitable for housing the Three phase four wire fully static Smart Energy Meter.

Design, Supply and delivery of Three phase four wire CT-PT operated DLMS/COSEM compatible fully static SMART Energy Meter .

Design, Supply and delivery of Pipe in Pipe Earth Electrode confirming to IS 3043: 1987, with chemical back fill compound and FRP cover for earthing the CSS and its equipments.

Supply and delivery of 50 x 6mm GI flat for earthing of various equipments.

Supply and delivery of 150mm dia C.I Pipe confirming to relevant Standards.

ERECTION SCOPE of WORKS: In view of space constraints only abstract of items are listed below. Therefore the Bidder should read the description of each items as detailed in the BOQ listed in Section-VI of Tender specifications before quoting. Rate should be quoted along with GST No. and prescribed rate of GST. DESIGN, ERECTION, TESTING AND COMMISSIONING OF FOLLOWING UNDER PACKAGE - 1 : Charges for Erection and commissioning of the 11 KV equipments at various proposed 11KV RMS yards for the 11KV Nethaji Nagar UG cable feeder with associated civil works, as per the Tender Technical specification.

Installation, testing and commissioning of 11KV Compact Sub-Stations (as described in item 1.01& 1.02)on the plinth foundation.

Installation, testing and commissioning of 11KV 3 way RMU (as described in item 1.06) on the plinth foundation

Installation, testing and commissioning of 11KV 4 way RMU (as described in item 1.07) on the plinth foundation.

Installation, testing and commissioning of 11KV 5 way RMU (as described in item 1.11) on the plinth foundation.

Installation, testing and commissioning of 11/.433 KV, 630KVA DT on the plinth foundation.

Installation, testing and commissioning of 11/.433 KV, 315KVA DT on the plinth foundation.

Installation, testing and commissioning of 800Amps 6 way LT SS Pillar Boxes on the plinth foundation.

Laying of 3 core 95 sq.mm XLPE insulated Armoured Screened type 11KV Al UG cable with end looses within the proposed RMS yards trenches for providing interconnections between RMUs and DTs.

Laying of 300 Sqmm XLPE Insulated (HEAVY DUTY) Armoured PVC Sheathed 3 ½ core 1100V Al UG cable in the cable trench within the yard with sufficient loose and its allied terminations with Al. lugs (Supply of 300sqmm long barrel Alluminium Lugs and insulation tape included).

Laying of 150 Sqmm XLPE Insulated (HEAVY DUTY) Armoured PVC Sheathed 3 ½ core 1100V Al UG cable in the cable trench within the yard with sufficient loose and its allied terminations with Al. lugs (Supply of 150sqmm long barrel Alluminium Lugs and insulation tape included).

Laying (2 runs for each pillar boxes) of 400 Sqmm XLPE Insulated (HEAVY DUTY) Armoured PVC Sheathed 3 ½ core 1100V Al UG cable in the cable trench within the yard and its allied terminations with Al. lugs (Supply of 400sqmm long barrel Alluminium Lugs and insulation tape included)

Labour for provision of Cable end termination (indoor and out door depending on the site conditions) for 3 core 95 sq.mm XLPE insulated Armoured Screened type 11KV Al UG cable at the RMUs Breaker sides and at DT HT side (for interconnection from RMUs to DTs) at various proposed RMS yards.

Labour for provision of Cable end termination for 3 core 400 sq.mm XLPE insulated Armoured Screened Type 11KV Al UG cable at the proposed RMU side and at the proposed CSSs HT side (for interlinking between proposed RMS yards).

Labour for provision of out door Cable end termination for 3 core 400 sq.mm XLPE insulated Armoured Screened Type 11KV Al UG cable at the take-off point at Marapalam SS. Suitable 150sqmm GI pipe support (Supply of pipe and clamps included).

Labour for providing 300 to 300 & 400 sqmm Straight through joint for connecting the new 300sqmm XLPE Insulated (HEAVY DUTY) Armoured PVC Sheathed 3 ½ core 1100V Al UG cable from CSS's DT's LT side 400Amps MCCB to the existing feeder UG cables (Mostly of 300& 400 sqmm dia cables) after removing the existing SS pillar Boxes in the yard and around it.

Labour for providing 150 to 150 sqmm straight through joint for connecting the new 150 sqmm XLPE Insulated (HEAVY DUTY) Armoured PVC Sheathed 3 ½ core 1100V Al UG cable from CSS's DT's LT side 400Amps MCCB to the existing feeder UG cables (Mostly of 300& 400 sqmm dia cables) after removing the existing SS pillar Boxes in the yard and around it.

Provision of Pipe in Pipe Earth Electrode with chemical back fill compound and FRP cover as required for various equipments to be erected within the yard and connecting this Earth Electrode with all the equipments

Design and Provision of aesthetic look designer fencing with hood and lighting for the 11KV RMS yard at various RMS yard locations.

DESIGN, ERECTION, TESTING AND COMMISSIONING OF FOLLOWING UNDER PACKAGE - 2 : Charges for Erection and commissioning of the 11 KV equipments at various proposed 11KV RMS yards for the 11KV Vanarapet UG cable feeder with associated civil works

Installation, testing and commissioning of 11KV 3 way RMU (as described in item 1.06) on the plinth foundation.

Installation, testing and commissioning of 11KV 4 way RMU (as described in item 1.07& 1.08) on the plinth foundation.

Installation, testing and commissioning of 11KV 5 way RMU (as described in item 1.10) on the plinth foundation.

Installation, testing and commissioning of 11KV 8 way RMU (as described in item 1.13) on the plinth foundation.

Installation, coupling by bus extension, testing and commissioning of Lucy Electric Make 11 KV, 3 Pole, Modular extensible type outdoor SCADA compatible SF6 insulated Ring main units (as described in item 1.14 ).

Installation, testing and commissioning of 11/.433 KV, 630KVA DT on the plinth foundation.

Installation, testing and commissioning of 11/.433 KV, 315KVA and 315 KVA DT on the plinth foundation.

Installation, testing and commissioning of 800Amps 6 way LT SS Pillar Boxes on the plinth foundation.

Laying of 3 core 95 sq.mm XLPE insulated Armoured Screened Type 11KV Al UG cable with end looses within the proposed RMS yards trenches for providing interconnections between RMUs and DTs and for HT supply connections.. Suitable support with clamping arrangements to be provided on the DT side cable to be raised for the terminations.

Laying of 300 Sqmm XLPE Insulated (HEAVY DUTY) Armoured PVC Sheathed 3 ½ core 1100V Al UG cable in the cable trench within the yard with sufficient loose and its allied terminations with Al. lugs (Supply of 300sqmm long barrel Alluminium Lugs and insulation tape Included).

Laying of 150 Sqmm XLPE Insulated (HEAVY DUTY) Armoured PVC Sheathed 3 ½ core 1100V Al UG cable in the cable trench within the yard with sufficient loose and its allied terminations with Al. lugs (Supply of 150sqmm long barrel Alluminium Lugs and insulation taps Included).

Laying of (2 runs for each pillar boxes) 400 Sqmm XLPE Insulated (HEAVY DUTY) Armoured PVC Sheathed 3 ½ core 1100V Al UG cable in the cable trench within the yard and its allied terminations with Al. lugs (Supply of 400sqmm long barrel Alluminium Lugs and insulation taps Included).

Labour for provision of Cable end termination (indoor and out door depending on the site conditions) for 3 core 95 sq.mm XLPE insulated Armoured Screened Type 11KV Al UG cable at the RMUs sides and at DT HT side(for interconnection from RMUs to DTs) at various proposed RMS yards.

Labour for provision of Cable end termination for 3 core 400 sq.mm XLPE insulated Armoured Screened Type 11KV Al UG cable at the proposed RMU side and at the proposed CSSs (for interlinking between proposed RMS yards).

Labour for provision of outdoor Cable end termination for 3 core 400 sq.mm XLPE insulated Armoured Screened Type 11KV Al UG cable at the take-off point at Marapalam SS. Suitable 150sqmm GI pipe support (Supply of pipe and clamps included).

Labour for providing 300 to 300&400 sqmm straight through joint for connecting the new 300sqmm XLPE Insulated (HEAVY DUTY) Armoured PVC Sheathed 3 ½ core 1100V Al UG cable from CSS's DT's LT side 400Amps MCCB to the existing feeder UG cables (Mostly of 300& 400 sqmm dia cables) after removing the existing SS pillar Boxes in the yard and around it.

Labour for providing 150 to 150 sqmm straight through joint for connecting the new 150 sqmm XLPE Insulated (HEAVY DUTY) Armoured PVC Sheathed 3 ½ core 1100V Al UG cable from CSS's DT's LT side 400Amps MCCB to the existing feeder UG cables (Mostly of 300& 400 sqmm dia cables) after removing the existing SS pillar Boxes in the yard and around it.

Provision of Pipe in Pipe Earth Electrode with chemical back fill compound and FRP cover within the yard and connecting this Earth Electrode with all the equipments of CSS.

Design and Provision of aesthetic look designer fencing with hood and lighting for the 11KV RMS yard at various RMS yard locations.

Charges for DISMANTALLING of existing 22KV OH Town feeder and its DP structures, Distribution Transformers and Pillar boxes as per the Tender specification. Rate should be quoted online in the BOQ format along with GST No. and prescribed rate of GST.

Dismantling of existing 22KV over head Town feeder throughout its route length and safe transportation of this removed material to the PED designated store which also includes reclamation of the dismantled site to its original level.

Dismantling of all existing DTs, pillar boxes and its DP structures connected with 22KV system and safe transportation of this removed material to the PED designated store.

DESIGN, ERECTION, TESTING AND COMMISSIONING OF FOLLOWING UNDER PACKAGE – 3: Charges for Erection and commissioning of the 11 KV equipments at various proposed 11KV RMS yards for the 11KV Rajnivas UG cable feeder with associated civil works

Installation, testing and commissioning of 11KV 3 way RMU (as described in item 1.06) on the plinth foundation.

Installation, testing and commissioning of 11KV 4 way RMU (as described in item 1.07) on the plinth foundation.

Installation, testing and commissioning of 11/.433 KV, 630KVA DT on the plinth foundation.

Installation, testing and commissioning of 11/.433 KV, 315KVA and 315 KVA DT on the plinth foundation.

Installation, testing and commissioning of 800Amps 6 way LT SS Pillar Boxes on the plinth foundation.

Laying of 3 core 95 sq.mm XLPE insulated Armoured Screened Type 11KV Al UG cable with end looses within the proposed RMS yards trenches for providing interconnections between RMUs and DTs and for HT supply connections. .Suitable support with clamping arrangements to be provided on the DT side cable to be raised for the terminations.

Laying of (2 runs for each pillar boxes) 400 Sqmm XLPE Insulated (HEAVY DUTY) Armoured PVC Sheathed 3 ½ core 1100V Al UG cable in the cable trench within the yard and its allied terminations with Al. lugs (Supply of 400sqmm long barrel Alluminium Lugs and insulation tape included).

Labour for provision of Cable end termination (indoor and out door depending on the site conditions) for 3 core 95 sq.mm XLPE insulated Armoured Screened Type 11KV Al UG cable at the RMUs sides and at DT HT side (for interconnection from RMUs to DTs) at various proposed RMS yards..

Labour for provision of Cable end termination for 3 core 400 sq.mm XLPE insulated Armoured Screened Type 11KV Al UG cable at the proposed RMU side (for interlinking between proposed RMS yards).

Labour for provision of out door Cable end termination for 3 core 400 sq.mm XLPE insulated Armoured Screened Type 11KV Al UG cable at the take-off point at Marapalam SS. Suitable 150sqmm GI pipe support (Supply of pipe and clamps included).

Provision of Pipe in Pipe Earth Electrode with chemical back fill compound and FRP cover within the yard and connecting this Earth Electrode with all the equipments of CSS.

Design and Provision of aesthetic look designer fencing with hood and lighting for the 11KV RMS yard at various RMS yard locations.

Charges for DISMANTALLING of existing 22KV OH Rajnivas feeder lines and its DP Structures, DTs and Pillar boxes

Dismantling of existing 22KV over head Town feeder throughout its route length and safe transportation of this removed material to the PED designated store which also includes reclamation of the dismantled site to its original level.

Dismantling of all existing DTs, pillar boxes and its DP structures connected with 22KV system and safe transportation of this removed material to the PED designated store.

DESIGN, ERECTION, TESTING AND COMMISSIONING OF FOLLOWING UNDER PACKAGE – 4(A): Charges for Provision of 11KV end terminations at women ITI yard and Dubrayapet RMS yard at NSC Bose salai

Labour for provision of Cable end termination for 3 core 400 sq.mm XLPE insulated Armoured Screened Type 11KV Al UG cable at the proposed RMU side and at the proposed CSSs (for interlinking between proposed RMS yards).

Design and Provision of aesthetic look designer fencing with hood and lighting for the 11KV RMS yard at various RMS yard locations.

DESIGN, ERECTION, TESTING AND COMMISSIONING OF FOLLOWING UNDER PACKAGE – 4(B): Charges for Erection and commissioning of the 11 KV equipments at various proposed 11KV RMS yards between SS Pillai Street and MG Road in the Petti canal Street with associated civil works.

Installation, testing and commissioning of 11KV 5 way RMU (as described in item 1.09) on the plinth foundation.

Installation, testing and commissioning of 11KV 6 way RMU (as described in item 1.12) on the plinth foundation.

Installation, testing and commissioning of 11/.433 KV, 630KVA DT on the plinth foundation.

Installation, testing and commissioning of 11/.433 KV, 315KVA and 315 KVA DT on the plinth foundation.

Installation, testing and commissioning of 800Amps 6 way LT SS Pillar Boxes on the plinth foundation.

Laying of 3 core 95 sq.mm XLPE insulated Armoured Screened Type 11KV Al UG cable with end looses within the proposed RMS yards trenches for providing interconnections between RMUs and DTs and for HT supply connections. Suitable support with clamping arrangements to be provided on the DT side cable to be raised for the terminations.

Laying of (2 runs for each pillar boxes) 400 Sqmm XLPE Insulated (HEAVY DUTY) Armoured PVC Sheathed 3 ½ core 1100V Al UG cable in the cable trench within the yard and its allied terminations with Al. lugs (Supply of 400sqmm long barrel Alluminium Lugs and insulation tape Included).

Labour for provision of Cable end termination for 3 core 95 sq.mm XLPE insulated Armoured Screened Type 11KV Al UG cable at the RMUs sides (for interconnection from RMUs to DTs) at various proposed RMS yards.

Labour for provision of Cable end termination for 3 core 400 sq.mm XLPE insulated Armoured Screened Type 11KV Al UG cable at the proposed RMU side and at the proposed CSSs (for interlinking between proposed RMS yards).

Provision of Pipe in Pipe Earth Electrode with chemical back fill compound and FRP cover within the yard and connecting this Earth Electrode with all the equipments of CSS.

Design and Provision of aesthetic look designer fencing with hood and lighting for the 11KV RMS yard at various RMS yard locations.

Charges for DISMANTALLING of existing OH Lines , DP Structures, DTs and Pillar boxes.

Dismantling of existing over head line, DTs and its DP structures and safe transportation of this removed material to the PED designated store. Which also includes demolition of existing civil plinths if any and safe removal of the demolished material from the yard and reclamation of the dismantled site to its original level..

S. T. ELECTRICALS PVT. LTD.

ELECTRICAL ENERGY EQUIPMENTS INDIA PRIVATE LIMITED