Tn No. 3344/3A dated 03.10.2025 6. Special repair work on the Mussapur road from Barouli Jahanpur road.

Providing, laying, spreading and compacting stone aggregates of specific size to water bound macadam Grade-3 specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled steel/ vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density, as per Latest Specification.

Providing & applying tack coat with V.G.-10 using bitumen distributor at the rate of 0.30 kg per sqm on the prepared granular surface treated with primer cleaned with hydroulic broom as per Technical Specification Clause 503.

Providing, laying and rolling of open - graded premix surfacing of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using viscosity grade bitumen VG-10 to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a smooth wheeled roller 8-10 tonne capacity, finished to required level and grades to be followed by seal coat as per Latest Specification.

Providing and laying seal coat by manual means with V.G.-10 Grade Bitumen sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type C as per Latest Specification.

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 (Grade-M-30), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days,using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501

Excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross-sections, and transporting to the embankment location with a lift upto 1.5 m and lead upto 1000 m as per Technical Specification Clause 302.3

Providing Plain Concrete (1:3:6) in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 Excluding GST

Brick Masonry Work in Cement Mortar 1:3 in Foundation complete excluding Pointing and Plastering, as per Drawing and Technical Specifications Clause no.600,1200&1203

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203

Providing and laying of Hume Pipe 600 mm dia NP-3 jointing ends fixing collars with 1:2 cement & coarse sand mortar.

Providing Reinforced Concrete M25 in open foundations complete, Centering and shuttering etc. as per direction of Engineer in charage. as per drawings and technical specifications Clause 802, 803, 1202 & 1203

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete as per direction of Engineer Incharage.