NIT No GE/ND-113/2024-25

Amount

B&R PORTION: Dismantling of plain or corrugated steel sheeting, any gauge and thickness including Nainital or similar pattern roof coverings complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not other wise described complete all as specified and directed.

Demolition of brickwork or stone/boulder masonary, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc., but excluding ashlar facing, dressed stonework and precast concrete articles complete all as specified and directed.

Excavation over areas not exc 1.5 mtr in depth and getting out any type of soil complete all as specified and directed.

Excavation over areas exc 1.5 but not exc 3 mtr in depth and getting out any type of soil complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete of grade M25 (using 20 mm graded aggregate) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

Use & Waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished surfaces complete all as specified and directed.

M&L for TMT bars 10 mm dia and over, cut to length , bent to shape required , including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

M&L for TMT bars 5 mm dia and over upto and including 10 mm dia, as in stirrups, spacers and binders, cut to length , bent to shape required , including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

M&L for brick work with sub class 'B' bricks , using old size bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

S&F mild steel trussess (framed) purlins, rafters, crane gantries, rails and fastenings and heavy brackets framing Beam, Tee, Angle, tubular sections , Channel of flat sections) including distance pieces, cleats etc conforming to Yst 310 complete all as specified and directed by Engineer-in-Charge. Note: Concept drawing/ picture shall be follow as attached

M&L for mild steel as in pillar, column, and jack rafters; purlins (Beam, Tee, Angle, tubular sections, Channel of flat sections) where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates incluing plates with weldig fixed properly conforming toYst 310 complete all as specified and directed by Engineer-in-Charge. Note: Concept drawing/ picture shall be follow as attached

M&L for MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment Fe 410 -W (Gde- E- 250) quality- B complete all as specified and directed.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) Exterior Louver. A solid co-extrusion panel of size 152 mm x 2900 mm comprising of virgin polymer High Density Poly ethylene, calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 2200 kg/cum of hybrid grade and screw withdrawal strength of 1800 N (Face), minimum compressive strength of 58 N/mm2, modulus of elasticity 850 N/mm2 with property of being termite/borer proof, water/moisture proof and GRIHA certified. The total thickness of the panel should be 6mm. The Panels shall be mounted on grid support system of 50 / 100mm M.S. (Hot Dip Galvanized-Minimum 100 microns) tubular section (or) Extruded Aluminium tube of 50x50x2mm as per instruction by Engineer in charge. The manufacturer should be ISO 9001:2015 Quality Management System Certification and ISO 14001:2015 Environmental Management Systems with in-house testing facility and should have their own manufacturing plant in India complete all as specified and directed. Make : Reynoarch, Rajshree, Floresta, Alstone, CenturyPly Note Concept drawing/ picture shall be follow as attached

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) Louver. A Solid co-extrusion panel of size 340.5 mm x 2440 mm/2900 mm and distance from wall 13mm comprising of virgin polymer High Density Poly ethylene, calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 2200 kg/cum of hybrid grade and screw withdrawal strength of 1800 N (Face), minimum compressive strength of 58 N/mm2, modulus of elasticity 850 N/mm2 with property of being termite/borer proof, water/moisture proof and GRIHA certified.The total thickness of the panels should be 2.2mm with 250 microns 3 layer UV film laminated over it. Exterior Warranty for Color should be minimum 10 Years in Indian Weather conditions. The Panels shall be mounted on grid support system of 50 / 100mm M.S. (Hot Dip Galvanized-Minimum 100 microns) tubular section (or) Extruded Aluminium tube of 50x50x2mm as per instruction by Engineer in charge. The manufacturer should be ISO 9001:2015 Quality Management System Certification and ISO 14001:2015 Environmental Management Systems with in-house testing facility and should have their own manufacturing plant in India complete all as specified and directed. Make : Reynoarch, Rajshree, Floresta, Alstone, CenturyPly Note Concept drawing/ picture shall be follow as attached

Demolition of cement concrete (unreinforced) in ground floor and pavings not exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for 40 mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in leveling layer and finishing the top surface even and rough to receive the topping layer or tiling complete all as specified and directed.

S&F in repair medium grade galvanised steel tubing with all fittings fixed to walls and ceilings or laid in floors for 25 mm bore GI tubings complete all as specified and directed.

Dismantling of stone slab and tiles of any description or thickness in floors, apron, laid, dry and pointed complete all as specified and directed.

M&L for Non - skid Ceramic colour and design tiles of size 300x300mm, in floors, swiming pool fountain etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete including 15mm thick screed bed in cement mortar (1:4) mixed with liquid water proofing compound as per manufacturer instructions complete all as specified and directed. Note: WPC shall be measured and paid separately

M&L for Non - skid Ceramic colour and design tiles of size 300x300mm, vertical surfaces, swiming pool fountain etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete 15mm thick back coat in cement mortar (1:4) mixed with liquid water proofing compound as per manufacturer instructions complete all as specified and directed. Note: WPC shall be measured and paid separately

M&L for 16-18mm thick Italian Marble machine cut in floor/ treads laid over cement 25mm thick screed in CM 1:4 and jointed with grey/colour cement slurry to match the tile suface including cutting and mirror polishing and laying by hightly skilled labours colour and shade shall be as per aproved by GE complete all as specified and directed. Note : (a) Minimum rate of Marble should not be less than Rs 400/- per Sqft including GST. Contractor shall submit purchase voucher for the same (b) Concept drawing/ picture shall be follow as attached

M&L for 16-18mm thick Italian Marble machine cut in vertical surfaces as skirting, dado, wall, column etc raiser. and including 15 mm thick rendering in cement mortar 1:4 and jointed with grey/colour cement slurry to match the tile suface including cutting and mirror polishing and laying by hightly skilled labours colour and shade shall be as per aproved by GE complete all as specified and directed. Note: (a) Minimum rate of Marble should not be less than Rs 400/- per Sqft including GST. Contractor shall submit purchase voucher for the same (b) Concept drawing/ picture shall be follow as attached

M&L for providing edge moulding marble stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc complete all as specified and directed.

M&L for carefully taking down brass railing of height 900mm and refixing duly clean/polish completed to the same position including repair/replaced all damage parts etc complete all as specefied and directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and directed.

Removing surplus excavated soil to a distance not exc 50 Mtr & depositing where directed at a level not exc 1.5 Mtr above the starting point complete all as specified and directed.

S&F PVC pipes single socketed in any length with rubber ring joints and fixing clamps using solvent adhesives fixed to walls with brackets etc of 110mm dia complete all as specified and directed.

S&F PVC (SWR) bends, tee, shoes etc any radius of 110mm dia complete all as specified and directed.

M&L for 15mm thick cement plastering in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished even & fair without using extra cement complete all as specified and directed.

M&L for Preparation of new plastered or un-plastered surface of wall/ceiling and applying two coats of Plastic emulsion paint with roller finish on any position over a coat of primer including preparation of surfaces with the application of multy layer of cement base wall care putty upto smooth fininshing complete all as specified and directed.

M&L for complete removal of existing treatment by mechanical grinder from old surfaces of ceiling/wall and applying two coats of Plastic emulsion paint with roller finish on any position over a coat of primer including preparation of surfaces with the application of multy layer of cement base wall care putty upto smooth fininshing complete all as specified and directed.

M&L for complete removal of existing treatment by mechanical grinder from old surfaces of ceiling/wall and applying Texture paint over base coat over primer over including preparation of surfaces with the application of multy layer of cement base wall care putty upto smooth fininshing design/ pattern shallbe as per dirction of engr in charge complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F mild steel work as in frame work, hanging structure (angle, flat, rond, rectangle, square or circle) including necessary welding or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-410 complete all as specified and directed. Note: Concept drawing/ picture shall be follow as attached

S&F for CNC cut design as approved by GE at 18mm thick WPC Jali for Plumbing Duct Cover, Shaft Cover, For Exterior use to provide solutions for exterior facade and elevational treatment for the building with waterproof, rusting proof with pigmented nature helps the color, unbreakabe including all fiting and fixing arrangement. The design and shape shall be porvided as per approved by Engineer in Charge and fixed with frame at concrete/brick structure including dismantling of RCC jali and removed the debries to Mod land complete all as specified and directed. Note: Concept drawing/ picture shall be follow as attached

Supply only liquid water proofing compound as per manufacture instruction complete all as specified and directed. Note: All the work in these items shall be carried out as per Architectural drawing attached with the CA and as per the direction of Engg in charge and GE

E&M PORTION: Taking down carefully old point wiring with aluminium/ copper conductor (Light / Fan/ Socket/ power Point ) complete including fittings such as ceiling rose, pendent holders, regulators and socket point etc and making good the disturbed surface & wall/ floor complete all as specified and directed.

M&L for point wiring with PVC insulated unsheathed multi stranded FRLS type copper conductor cable of size 1.5 Sqmm 1100 V grade including one run of PVC insulated unsheathed multi stranded FRLS type copper conductor cable of size 1.5 sqmm as earth continuity conductor connected to common earth dolly in and including PVC concealed conduit 20 mm dia medium grade ISI marked and its accessories including provn of new factory made pressed steel modular switch/terminal box of suitable size and new modular front & back plates of approved colour/model of suitable size for housing the modular switches, sockets, fan regulators for one light/ fan/ exhaust fan point controlled by one no, one way 5 Amp switch complete all as specified and directed. Note: (i) Cutting chases for concealed conduit and making good in cement mortar is deemed included in unit rate. (ii) No cutting shall be done in the roof for laying PVC conduit for ceiling point wiring. In this specified portion wire shall run through the existing conduit or surface new conduit shall be provided as required. (iii) In case the wiring is encountered with any beam/column, then the wiring will run on surface to avoid any damage to the RCC portion.

All as per item No 40.00 above but One three pin socket outlet 6 amps point controlled by one no, one way switch on independent board complete all as specified and directed.

All as per item No 40.00 above but with 2.5 sqmm (for phase, neutral) and 2.5 sqmm (for continuous earth wire) cable for one 15/16 amp socket out let point on independent board complete all as specified and directed.

S&F in replacement of modular Switch 6 amps,one module, 230 vots, single pole, one way (ISI marked) complete all as specified and directed.

S&F in replacement 16 Amp rating modular switch one way one module complete all as specified and directed.

S&F in replacement of modular socket out let 230 volts, 6 Amp - 2/3 pin combined 2 module complete all as specified and directed.

S&F in replacement of modular socket out let 230 volts, 16 Amp - 2/3 pin combined 2 module complete all as specified and directed.

S&F in replacement of factory made sheet steel distribution boards, double door, made out of CRCA mild steel sheet with insulating material like polyester epoxy coated surface mounting SPN 12 way, concealed type, 240 volts AC with suitable busbar, neutral link, earth link suitable for MCB, DP/SPN as incomer & MCB SP as outgoing complete all as specified and directed.

Supply and fixing in replacement of MCB, 240V 10KA, B/C curve MCB SP 6 to 32 Amps complete with connection complete all as specified and directed.

Supply and fixing in replacement of MCB, 240V 10KA, B/C curve MCB SPN 40-63 Amps complete with connection complete all as specified and directed.

S&F in replacment of strip led light in false ceiling consist of 120 led per meter warm white complete all as specified and directed. Make: Philips Cat Part No Lineaglow 120Led/mtr or equivalent of make as specified in PS.

S&F in replacement wall light of 5-10 watt with conical focus made of PVC complete all as specified and directed. Make: Philips Cat Part No 582060 or equivalent of make as specified in PS.

S&F in replacement picture light 10 watt adjustable type, Direct the light at any angle with 230 degree tilt and 360 degree rotation, color warm/white complete all as specified and directed. Make: Philips Cat Part No flexspot COB 10W or equivalent of make as specified in PS.

S&F in replacement step led light 5-10 watt for staircase complete all as specified and directed. Make: Philips Cat Part No 31436 or equivalent of make as specified in PS.

S&F in replacement COB LED Light rececss mounted 12 watt made of PVC and Interior coating of Aluminium complete all as specified and directed. Make: Philips Cat Part No flexBeam COB or equivalent of make as specified in PS.

S&F in replacement 12 watt bolard light for lightening the pedestrial of garden ,dust proof and water resistant light of size 815x140x104 mm complete all as specified and directed. Make: Philips Cat Part No 582089 Philips VIBE UNIQ Cone 12W WW or equivalent of make as specified in PS.

S&F chandeller finest sparkling, Corona Pendant Crystal SS Chrome G9 7*MAX 42W, unique Crystal pendant, special french gold finish, efficient G9 Bulb compatibility, versatile elegance Bulb type G9 Dimnesion Dia 510 x H 1440 mm complete all as specified and directed. Make: Philips Cat Part No 581846 or equivalent of make as specified in PS.

S&F in replacment for submain wiring with PVC insulated unsheathed copper conductor multi stranded FRLS type 1100V grade 2 x6 sqmm complete drawn in new PVC concealed conduit and its accessories along with 1x 6 sqmm PVC insulated unsheathed copper conductor multi stranded FRLS type cable for continuous earth wire and duly connected to common earth dolly complete all as specified and directed.

S&F rigid non-metallic PVC conduit medium grade 20 mm dia for telephone cable complete with all fixing accessories complete all as specified and directed.

M/S MSD & Associate (BID ID -3294333)

M/S Sunil Steel Works (BID ID -3295342)

J S CONSTRUCTION CO (BID ID -3296610)