Additional Work for Development of INS Khukri Memorial Hill at Chakratirth Beach, Diu (Phase-II).

Civil Works :

Demolition including stacking of serviceable materials and disposal of unserviceable materials with all lead and lift. ( i ) RCC work

EARTH WORK Excavation in all kinds of soil, wet or dry ( such as yellow murrum, hard murrum/gravel, soft rock or mixture of any kind, etc.) in loose and slushy condition, for depths as required from existing ground level or approved strata for foundations, trenches, pits, rafts of walls, plinths, area levelling, etc.; including disposing off surplus excavated material within lead of 50mtr. as per direction of the consultant/site engineer at approved location; if required dewatering by bailing by pumping out rain and surface run off water to keep the site dry at all times until completion of work; making temporary stepping/sloping and working space is provided as per IS 1200 including trimming, dressing of sides, leveling or grading, cleaning, removing and excavating loose pockets and consolidating and compacting them by back filling to achieve 95% proctor density at optimum moisture content as directed by the consultant/site engineer all complete to his entire satisfaction using all necessary mechanized tools. Rates are inclusive of lead and lift. a. upto 1.5m depth

EARTH WORK as per Item Description of 2. upto 1.5m depth (in soft rock not requiring blasting)

EARTH WORK as per Item Description of 2. from 1.5m to 3.0m depth (in soft rock not requiring blasting)

FILLING OF EARTH (excluding rock) for making up levels such as for plinths, trenches, sides of foundations or for raising ground levels for landscaping, behind retaining walls, levelling under structures, etc. as per final formation levels, with approved quality soil in layers not exceeding 200mm in-depth, breaking clods, watering, compacting each layer with vibrator compactor or roller and at inaccessible places with wooden/steel rammers to achieve 95% proctor density at optimum moisture content; dressing up filling; required dewatering by bailing/pumping out of water to keep site dry while back filling etc. lead upto 2kms. and lift upto 1.5m complete as per direction of the consultant/site engineer to his entire satisfaction. Rates are inclusive of lead and lift.(a) Filling available excavated earth(excluding rock in trenches plinth, sides of foundations etc. in layers not exceeding 20 cm in depth consolidating each deposited layer by ramming and watering.

Rolling and consolidation of compacted earth including filling in depression which occur during the process with power roller of 10 tones and watering of earth work.

RCC AND CONCRETING WORKS Providing and laying in position machine batched and machine mixed and well vibrated using machine vibrators; controlled M25 grade reinforced cement concrete (RCC) for concrete in sub and super structure at all floors for footings, coping, rafts, stub columns, columns, plinth beams, tie beams, beams, slabs , cantilevers, etc. using 20mm nominal size well graded approved quality aggregate as per approved design mix minimum cement content as per IS 456:2000 including the cost of centering, water tight shuttering, bonding agent to bond new and old concrete surface and vibrating/compacting, curing, scaffolding, contractor's hoist, establishing approved dewatering system to keep site dry all time, cleaning, preparing surfaces, junctions, pressure grouting joints, if required, hacking closely, etc., the rate shall include groove cutting as per architectural drawings and providing recesses, drip mould to slabs, walls, columns, openings, sleeves in slabs, construction joints, sunk slabs, cantilevered slabs, etc. to required shapes, size and slope at all levels complete to the satisfaction of the Engineer in charge. RCC walls - for fins- upto floor two level - Rates shall be inclusive of providing PVC water stoppers with central bulb and 150mm wide serrated for RCC walls for water tanks.

REINFORCMENT STEEL AND STRUCTURAL STEEL WORK Providing, straightening, cutting, bending and binding in position of TMT bars conforming to IS 1786 with FE500D N/Sq mm conforming to IS, to correct shape and size as per detailed drawings, specifications and approved bar bending schedules, in substructure footings, rafts, walls, columns, slabs, beams, etc.; with correct size PVC cover blocks of same grade of concrete and binding wire of 18 gauge including dewatering to keep site dry etc. complete to the satisfaction of the consultant/site engineer. - for works upto floor two level

REINFORCMENT STEEL AND STRUCTURAL STEEL WORK Providing Fusion Bonded Epoxy (FBE) coating not less than 175micron thickness and upto 300micron to reinforcement bars as per IS-13620-1993 / ASTM - 775 M including testing of coating at plant and all taxes (A) 10mm to 16mm dia bar

Providing and fixing stainless steel ( Grade SS-304) stair case/ balcony , railing, consisting of stain less steel Baluster 40 mm dia x 2 mm thick ( @1.928 kg/mtr) one no. at each end of flight with vertical supports of 25mm dia. x 2 mm thick (@1.166 kg/mtr) at 0.75 mt c/c alongwith 3 nos of horizontal stainless steel pipe 15 mm dia. x 2 mm thick (@0.659 kg/mtr) running parallar to the flight , with 40 mm dia. x 2 mm thick Stainless steel pipe (SS 304 Grade) hand rail with stain less steel screws complete as per design and drawings. All the stainless steel material should be SS-304 type and as per relevant IS specification.

WHITE BELA STONE MASONARY Providing and laying coursed stone rubble masonry with hard stone of approved quality in foundations and plinth in cement mortar 1:6 etc complete. The rates shall be inclusive of all tools, tackles, plant, machinery and scaffolding equipment's. The works shall be carried out to the complete satisfaction of the engineer in charge and shall be line, level and plum. The joints of the stone shall be properly and firmly filled using properly mixed mortar and the joints shall be cleaned and well pointed using cement mortar.

FLOORING AND TILING WORK Dark Gray Granite rough granite as per approved samples. Providing and laying 20 mm thick, machine cut, fine chisel dressed stone slab in flooring, paving, treads, nosings,corbels and bands over 20mm (average) thick base of cement mortar 1 : 5 ( 1 cement : 5 coarse sand), butt jointed with a joint width of not more than 1mm, in white cement mortar 1 : 2 ( 1 white cement : 2 stone dust) mixed with pigment to match the shade of stone slab complete. Rates are inclusive of laying the stone as per the patterns shown in the drawings. Rates shall be inclusive of arranging of samples of tiles, stones, granites etc as directed by the Consultants and the engineer in charge for approvals of the the same well in advance and prior to using them in works. All materials shall then match the quality, thickness, size, characteristics, technical parameters and make of the approved sample only. Deviation if found in the materials thereon, the material shall be liable for rejection in part or total.)

FLOORING AND TILING WORK Light Gray Granite Rough granite as per approved samples. Providing and laying 20 mm thick, machine cut, fine chisel dressed stone slab in flooring, paving, treads, nosings,corbels and bands over 20mm (average) thick base of cement mortar 1 : 5 ( 1 cement : 5 coarse sand), butt jointed with a joint width of not more than 1mm, in white cement mortar 1 : 2 ( 1 white cement : 2 stone dust) mixed with pigment to match the shade of stone slab complete. Rates are inclusive of laying the stone as per the patterns shown in the drawings. Rates shall be inclusive of arranging of samples of tiles, stones, granites etc as directed by the Consultants and the engineer in charge for approvals of the the same well in advance and prior to using them in works. All materials shall then match the quality, thickness, size, characteristics, technical parameters and make of the approved sample only. Deviation if found in the materials thereon, the material shall be liable for rejection in part or total.)

PLASTERING WORK Preparing surface ,providing and applying 20mm thick cement plaster in double coat mala plaster finished even & smooth in first coat of 12mm cement mortar 1:5 and second coat of 8mm cement mortar 1:4 ( 1 cement : 4 sand ) on internal and external brick walls and RCC surfaces including necessary H frame tubular MS pipe scaffolding without making holes in walls, supplying and adding waterproofing compound of approved make and to be added as per the manufacturers instructions, making surface rough, curing, making sharp and clear grooves, pattas, zari filling by raking of RCC and Stone masonry joints, cleaning them and preparing the joints by pointing / grouting them using mixture of square crused aggregates and rich cement mortar and then providing 20guage GI chicken mesh150mm wide finished etc. complete at all levels as directed and to the satisfaction of the Consultant / Engineer in Charge.

Supplying approved chemical emulsion in sealed containers including delivery as specified in concentration as per recommendation of manufacturer, diluting and injecting chemical emulsion for pre construction and post construction chemical anti-termite treatment of Gujarat Pesticides, Meghmani organics, Bayer Corp. SC or equivalent make as per IS 6313 1971 that shall create a chemical barrier under and around the foundation pits and trenches, below plinth, under floor back filling, along external perimeter of building, surrounding pipes, conduits, etc. all complete using chemicals Aldrin 0.5EC/ Dioldrin )0.5EC/ Heptachlor )0.5 EC/ Chirodon 1. DEC spraying by hand pump etc and making holes where directed confirming to specifications and as per approved manufacturer’s Instructions and recommendation, and installed by manufacturer’s approved agency with a guarantee of 10 years, all to the satisfaction of the consultant. (Plinth area in plan at ground floor level shall only be measured for payment.) . Rates shall be inclusive of all kinds of material, labour, drilling of holes and injecting the chemicals as directed by the Engineer in charge.

Drilling holes of min 16mm diamater into existing concrete substrate for anchoring of new rebars and depth 300 mm of rebar and fixing with pure epoxy resin based cartridge form chemical anchor material of BASF/HILTI/FISHER or approved equivalent product cutting, fabricating, chemicals, tools, labour, plants, machineries, scaffolding etc. complete as directed by Engineer-in- charge.

Cleaning of rust / scales/ corrosion from reinforcement bars should be carried out using rust remover, Reebakleens RR of Fosroc. The material to be applied to the rusted metal bar, using brush and leaving it to dry for 30 mins. & washing surface with fresh water as required to exposed reinforcement bar and applying inhibition coats/system to exposed reinforcement bars, after cleaning & removing scales and rust completely as specified Two component inhibitor of BASF/SIKKA/FISHER or equivalent product including labour, tools, scaffolding, electricity, plant and machineries complete as per detail specification and as directed by Engineer-in-charge.

Apply dr fixit Epoxy bonding agent or equivalent over the saturated dry surface as a old and new concrete bonding agent over the entire dismentled/Existing concrete surface including labour, tools, scaffolding, electricity, plant and machineries complete as per detail specification and as directed by Engineer-in-charge.

LAMINATED GLASS WITH ETCHING Providing and fixing (10mm +1.52 +10mm plain laminated glass & fins glass 10mm +1.52 + 10mm +1.52 +10mm ,) plain laminated glass glazing panel as shown in Consultants detail drawings, stainless steel spider fittings and connector fittings and as per the specifications of the manufacturer. The glass shall be of Modiguard, Asahi or equivalent. The joints shall be sealed using transparent silicon sealant of Dow corning, Wacker make or equivalent. Rate includes all wastage and additional costs required for profile cutting in shapes and sizes as per design. Rates shall include for etching works as shown in the design drawings. PVB to be of Du Pont or equivalent material. All Complete as per drawing and as directed by the Engineer InCharge.

Providing and fixing Urinal of approved quality including connection with trap and with integral longitudinal flush pipe.(A)Squating plate pattern white earthenware 550mm x 300mm.

Providing and fixing screw down bib taps of following size.(A) Brass screw down bib tap polished bright. (i) 15mm dia.

Providing and fixing washbasin with single hole for pillar tap with C.I. or M.S.brackets painted white including sutting holes and making good the same but excluding fittings.(A) Vitreous China:(ii)Flat Back Washbasin 550 mm xv 400mm size. (i) In white colour.

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 75 mm diameter with jali of the following nominal diameter of self cleansing design with C.I scread down or hinged grating including the cost of cutting and making good the walls.

Providing and fixing brass screw down stop tap.(A) 15mm dia.

Providing and fixing pillar tap, capstan head, screw down high pressure with screws, shanks and back nuts. (i) 15mm dia

Providing and fixing Health Fauset Heavy duty with hook with fitting.

Providing and fixing Waste Pipe for Wash basin C.P. 32 mm dia.

Providing and fixing PVC SWR pipes IS 13592 for Drain - 110 mm dia.

Providing erecting and fixing double coated Syntex PVC. (ISi) water tank of required capacity each with all necessary fittings and connection etc. complete on terrace.

Careful removal of existing deteriorated / damaged / weathered plaster from the ancient shrines / temples without damaging the surface by using proper tools . Applying lime plaster 20mm thick in two coats (first coat will be in 12mm and second coat will be 8mm thick) over small ancient shrines towards east side of temple using L.S.S. (1:1:1) (1 lime : 1 sand : 1 surkhi) mortar mixed with additives like gur, gugal, bail fruit, methi etc. including cost of all materials and labors including erection of scaffolding T & P for the work etc complete as directed by site in-charge.

Point wiring for Light / Bell with 2-1.5 sq.mm & arthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in/ on surface on wall/ceiling complete with 6A Modular type switch / bell push & accessories and earth continuity of following type, erected on PVC / Metallic box, single mounting base frame covered with textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed. (a) with medium class Rigid PVC pipe and accessories. Cat- III

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of to be erected concealed in / on surface of wall / ceiling complete with Modular type switch & 5 pin Plug erected on PVC / Metallic box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories. [I] For 6A Plug with 2‐1.5 sq.mm Cu. Wire (a) with medium class Rigid PVC pipe and accessories. Cat‐ III

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of to be erected concealed in / on surface of wall / ceiling complete with Modular type switch & 5 pin Plug erected on PVC / Metallic box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories. [II] For 16A Plug with 2‐2.5 sq.mm CU. Wire (a) with medium class Rigid PVC pipe and accessories. Cat‐ III

Providing and erecting Sheet Steel powder coated MCB distribution board ‐ flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486‐1986 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) (F) Single phase 8 way SS Double door

Making trench in soft soil of suitable width of 90 cms deep for laying cable or locating the fault all over the run and backfilling the same and making the surface as normal ground.

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. (b) 2 to 4 core 4 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. (c) 2 to 4 core 6 Sq. mm

Providing & Earecting approved ISI mark medium class rigid pvc pipes of following size complete to be erected on/in wall or ceiling erected with nacessary PVC fittings & junction boxes fixed with adhesive solution & clamps with approved manner as directed.(b)25 m

Providing & laying approved make Double walled corrugated pipes (DWC) of polyethylene(conforming to IS 14930 II )with necessary connecting accessoriesof same material at required depth for laying of cable. below ground / road surface for enclosing cable and back filling the same to make ground as per original.(A) 50 mm dia

Supplying & erecting in earthpit of minimum bore dia. 225mm size ASH or approved make Safe Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043 1987 made of corrosion free G.I.Pipes having Outer pipe dia of 80 mm having 80-200 Micron galvanising, Inner pipe dia of 40 mm having 200-250 Micron galvanising, connection terminal dia of 14 mm with constant ohmic value surrounded by highly conductive compound with high charge dissipation suitable for following type of applications. [C] For Electrical Installation covering Transformer Neutrals, Lightning arrester Earthing, A.C.Plant & Sensitive Computer System(like Automation, SCADA)i.e. independent Earthing located in other than normal soil i.e. Soft Rock, Marshy Soil etc.. -Length of Pipe : 3 Mtrs. -Back filling Compound :2 nos Bags of 25 Kg.

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables. (A-1) 4 core 4 Sq. mm

Supplying and erecting Flexible PVC insulated multistrand multicore 1.1 kv grade ISI marked copper wires of following size to be erected as directed. (A-1) 4.0 Sq.mm 4 core round PVC sheathed

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables. (A) 4 core 2.5 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables. (A) 3 core 2.5 Sq. mm

Supplying and erecting Flexible PVC insulated multistrand multicore 1.1 kv grade ISI marked copper wires of following size to be erected as directed. G) 16 Sq.mm 1 core round PVC sheathed Green

Supplying and erecting Flexible PVC insulated multistrand multicore 1.1 kv grade ISI marked copper wires of following size to be erected as directed. C) 2.5 Sq.mm 1 core round PVC sheathed Green

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity (a) 6 to 32 Amp. Cat-III.

415 V MCB Four Pole 63 Amp. Cat-III.

Making trench in Hard/ Rock soil of suitable width of 90 cms deep for laying cable or locating the fault all over the run and backfilling the same and making the surface as normal ground.

Supplying and erecting approved make Bracket fan (Wall fan) of 230 volt, A.C. 50 Cy/s., 400/450 mm sweep complete erected on wall or with lead Cores and connections complete.Cat III

SITC of 9 Watt 230V LED diecast aluminium housing Spike light IP-66 as per Cat-II. K-LITE make.

Supplying and erecting LED Track light horizontal control gear with diecast aluminium housing , 24 to 50 degree beam angle with High power LEDs of 3000K colour temperature, Dimmebale Driver, 3wire surface power track, cat-III (a) 20 Watts as approved.

SITC of Recess Mounted Flood light type luminaire KESLEC make . Ractangle in shape with an indirect optical system having flow of light towards the ground. The Luminaire shall be 15 W, rated as class -1 with an Integra driver, Colour Temp. shall be 3000 K, LED CRI > 80 % .The housing shall be lof low copper content die cast aluminium with high corrosion resistance, Tempered glass and synthetic materials reinforced with fibre glass, guarantee these recessed floodlights adequate robustness for installation in an urban environment. The Lighting fixture shall be front openable type.

SITC OF LINEAR POLE made out of G.I. of 4mtr. height made out of G.I curved tubular pole, primered and marine grade painted . junction/ looping box with 10Amps. Heavy duty connector shall be built into the pole. mounting plate 200x200x8mm and EN-8 foundation bolts 4 nos. make by KESELEC.

Supply installation and testing of LED Post top luminaire KESLEC SOFIA 40W Post of lantern made out of UV stablised acrylic and aluminium daicast having IP 66 integral driver and LED component suitable for pole mounting awailable in 4000 k opreated at 240 v A/C

SITC OF CURVED CONICAL TUBELAR POLE of KESELEC made with three arm decorative bracket of 6 mtr. height made out of G.I curved tubular pole, primered and marine grade painted . junction/ looping box with 10Amps. Heavy duty connector shall be built into the pole.The pole should be also with Three arm bracket of 38mm length, in three directions, mounting plate 200x200x8mm and EN-8 foundation bolts 4 nos. make by KESELEC

Supply and installation of 55watt Decorative floodlight of KESLEC made out of Aluminium diecast and decorative covered with engineering plastic coating IP:66 driver supply voltage 220V.

Supply installation and testing of in ground one way light luminaires made up of SS Housing corrosion resistance, hard chromeplated stainless steel:316 grade front ring, translucent diffuser, silicone seal gaskets, optical lens >85% , integral power supply, IP:65 suitable for 220V. make By K-LITE.

Supplying and erecting approved make LED batten 18 watt 230 V. approved make.

Providing and Fixing of weather proof Pulg socket 16A 3pin 240V with MCB IP:67 polycarbonate enclosure mennekes make.

HORTICULTURE AREA DRESSING AND LAND LEVELLING: Scraping and removing of top soil and debris from exsiting ground and levelling of ground for garden development as per proposed levels etc. complete as directed by engineer-in-charge.

SHRUBBERY/HEDGE PLANTATION (1' height) :Supply & plantation of shrubbery plants (To be planted in existing soil and already dressed area ) development of bed, cultivation soil mixture and plantation of shrubbery (as per plantation plan provided). Pesticide application.Good earth and farm yard manure to be added wherever it is required. a.Ipomea Biloba (20 plants/M2 = 8560 Nos.) b.Thespesia var.(4 plants/M2 = 2400 Nos.) c. Casuarina(4 plants/M2 = 1212 Nos.)

TREE PLANTATION (10' to 12' height, 1' girth) : Supply & plantation of trees as per specified plantation plan. This will also include excavation of pits (90cm x 90cm x 90cm) ,mixing of soil additive @ 10kg per pit and existing soil, pesticides application. Good earth and farm yard manure to be added wherever it is required. Barringtonia racemosa ( 55 Nos.)

IRRIGATION Supply of Irrigation Hardware - Pipes, Irrigation Devices- Sprinklers, Drip, Valves, Automation Components- Valves, Controllers, Cables, Pumping System, Filtration Unit. PVC Pipes with all PVC Accessories Like Tee, Bend, Reducer, Solvent etc. All Fittings should be minimum pressure of 10 Bar as per given below for respective sizes.As Per IS 4985:2000 (Supreme/Finolex/Astral) PVC Pipe 90mm x 6 kg/cm2 (Supreme/Finolex/Astral)

PVC Pipe 63mm x 6 Kg/cm2 (Supreme/Finolex/Astral)

PVC Pipe 50 mm x 6 Kg/cm3 (Supreme/Finolex/Astral)

PVC Pipe 40mm x 6 Kg/cm2 (Supreme/Finolex/Astral)

SCH 80 PVC Pipe 1" (Supreme/Finolex/Astral)

SCH 80 PVC Pipe 3/4" (Supreme/Finolex/Astral)

DW C Pipe 150 mm SN 6 Used as Road sleeve (Supreme/Finolex/Astral)

Supply , Installation and Testing of Drip and Accessories Drip In Line Lateral Pipe 16 mm X 4kg , 3.5 LPH, 45 cm (Brown) 1,15 Thickenss, The pressure-compensating emitter design provides a consistent flow over the entire lateral length ensuring higher uniformity for increased reli ability in the pressure range of 8.5 to 60 psi. The bend radius for XFD dripline is 3” no matter which way you bend. The inline emitter diaphragm shall have a pressure- regulating diaphragm with a spring action allowing it to self- rinse if there is a plug at the outlet hole (Rainbird/ Metzer/ Netafim)

Drip Online lateral Poly Pipe 16mm X 4 kg (Brown) 1.15 Thickness Brown in Colour. Material : LLDPE (Rainbird/ Metzer/ Netafim)

Dripper 8 LPH (Rainbird/ Metzer/ Netafim)

Take off Assembly (PP Clamp Saddle40mm x 1/2" + SCH 40 1/2" Pipe + 17mm Barbed x 1/2" Male Tee) Lateral end stop (Rainbird/ Metzer/ Netafim)

PVC Flush Valve 40 mm for Flushing of Submain and Mainline for Debris. Material : PVC PN 6 (Rainbird/ Metzer/ Netafim)

Tee / Elbow 17 mm High quality barbs grab tubing for a secure fit • Unique barb design to reduce insertion force and still retain a secure fit. Brown color to match XF Dripline, Made of sturdy, break-resistant plastic (Rainbird/ Metzer/ Netafim)

Lateral Hold Stake- 9" Inch Long 12 Gauge MS W ired with Hot Deep Galvnised (G.I.)

PVC Ball Valve 63 mm PN 10 Double Union Type. Solvent W eld. Materials: Ball valves: body in gray or black PVC, handle in PVC ( gray, black, blue or red), ball seat in PTFE or PE, o-rings EPDM or FPM. , o-rings in EPDM, stem in zinc-plated steel,Metric series : to ISO 727, EN 1452/4, BS 4346/1 comply with pipes to ISO 161/1, BS 3506, BS 3505. Threaded series : to UNI ISO 228/1, DIN 2999, BS 21. Flanged series: to DIN 2501, ISO dis. 9624, UNI 2223. BS 10 table d/e, ASA ANSI b16.5 class 150, JIS 2212 (k10 and k5). (GF+/ FIP/Astore, Italy)

12" Rectangle Valve Box- Corrugated sides provide strength both • before and after knock-outs are removed. Beveled lid edges help prevent damage to • lids from lawn equipment. Bolt hole knock-out in the lid keeps insects • out of the box when bolt is not used. Interlocking bottoms allow boxes to mate • securely together bottom-to-bottom for deep installations. Optional stainless steel bolt and clip securely • fasten the lid to the body. Size :Length: 21.8 inches (55,4 cm) Width: 16.6 inches (42,2 cm) Height: 12.0 inches (30,5 cm) (Rainbird/ Metzer/ Netafim)

Double Acting Air Release Valve 1" - Kinetic Straight flow body with large diameter orifice – High flow rates. Aerodynamic full-body kinetic shield – Prevents premature closing without disturbing air intake or discharge. Dynamic sealing – Prevents leakage during operation even under low pressure conditions (0.1 bar). The boss on the base can be tapped with a thread for pressure gauge connection, check point or test drain for air valve function. Compact, simple and reliable structure whose parts are fully corrosion, chemical and fertilizer resistant – Lower maintenance and increased life span. Factory approval and Quality Control – Performance and specification tested and measured with specialized test bench, including vacuum pressure conditions. (Bermad/ ARI/ Rainbird)

P.P. Clamp Saddle for (75 mm x 1")

Round Valve Box 10". Valve boxes shall be used as durable, rigid enclosures for valves or other irrigation system components requiring subsurface protection for installation or maintenance. The valve box shall be made of structural foam HDPE resin that is resistant to UV light, weather, moisture and chemical action of soils. Valve box body and black lid shall be composed of 100% recycled HDPE. The body shall have four knock-outs molded into the sides that can easily be removed. The knock-outs shall remain an integral part of the body unless to run pipes or wires through the valve box. The valve box shall have corrugated sides. The valve box shall have a stepped feature on the bottom that securely interlocks two boxes together when mated bottom- to-bottom for use in a deep installation. size : Top Opening (diameter): 8.9" (25.1 cm) Maximum Top: 10.7" (27.2 cm) Bottom Opening: 11.9" (30.2 cm) Maximum Bottom: 13.8" (35.0 cm) Height: 10.0" (25.4 cm) (Rainbird/Toro/ Dura)

Solenoid Valve 2" Glass Filled Nylon. PN 10 • Body constructed of durable glassfilled nylon for long life and heavy-duty performance at 200 psi (13.80 bar) pressure • Stainless steel studs molded into the body. Bonnet can be attached and removed more easily without damaging threads • One-piece solenoid design with captured plunger and spring for easy servicing. Prevents loss of parts during field service • External bleed protects the solenoid ports from debris when system is flushed • Internal bleed operates the valve without allowing water into the valve box; allows pressure regulator to be adjusted without turning on the valve at the controller first • Low flow operating capability • Slow closing to prevent water hammer and subsequent system damage. Electrical Specifications • Power: 24 VAC 50/60 Hz (cycles/sec) solenoid • Inrush current: 0.41 A (9.84 VA) at 60 Hz • Holding current: 0.14A (3.43VA) at 60Hz • Coil resistance: 30-39 Ohms (Rainbird/ Toro/ Orbit)

Controlled Automized Cable #12/1 Paige/ Rainbird Make - Common, Insulation Thickness: .045". single conductor insulated wire sizes 12 AW G, utilizing low density high molecular weight polyethylene insulation, suitable for direct burial applications for operating temperatures up to 60°C. Listed by UL or ETL or CSA. (Rainbird/Toro/Paige)

Controlled Automized Cable # 14/1 Paige/ Rainbird Make - Hot Insulation Thickness: .045". single conductor insulated wire sizes 12 AW G, utilizing low density high molecular weight polyethylene insulation, suitable for direct burial applications for operating temperatures up to 60°C. Listed by UL or ETL or CSA. (Rainbird/Toro/Paige)

Erection of Irrigation Hardware - Pipes, Irrigation Devices-Sprinklers, Drip, Valves, Automation Components-Valves, Controllers, Cables, Pumping System, Filtration Unit. Excavation & Back Filling

Installation Charges - Laying of Pipes, Sprinklers, Drip Lines, Valves, Cables, Pump Station and any other required fixture to complete the system and make it operational.

Supplying and stacking of good earth (Garden Soil) including spreading simulataneously as directed. Good earth shall be a friable, tyoical of cultivated top soil of the locality. It shall be free of sub-soil, stones, earth clad, sticks roots or other objectionable extraneous materials no topsoil shall be delivered in a muddy condition, etc complete as required.

Manure : Supplying and stacking of dry farmyard manure free extraneous matter harumful bacteria, insects and chemical on site.

Supply of Coir Geo-textile (700Gsm). Including 9 nos. Holdstack, labour work:- Laying of Geo-textile, fixing of Hold Stack, Dressing & Levelling with manual compaction (Wooden rammer) After adding 2" thick soil from location.

P.R. Patel and Co.

TIRUPATI SARJAN LIMITED