REPAIR REPLACEMENT OF INTERNAL ELECTRIFICATION WORKS FOR CERTAIN OFFICE COMPLEX OF HQ CWE (U) GE (U) PM AND VARIOUS LOCATIONS UNDER GE (U) PM DELHI CANTT10.

Amount

Material & Labour for earthing with galvanized steel earth plate electrode of size 60cmx60cmx6mm thick bured directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to the galvanized earth lead by means of bolts, nuts check nuts and washers of galvanized iron or steel using GI or steel wire 4mm dia as earthing lead as shown in electrical plate No 3 of SSR Part-I connected to earthing test point all as specified or indicated including testing on completion including necessary excavation and earth work in soft/loose soil, returning filling, disposal of surplus soil, earth pit in PCC 1:3:6 type C-1 using 20mm graded stone aggregate pit, funnel, 20mm dia GI medium grade watering pipe, 15mm dia GI medium grade earth lead protection pipe and pre-cast earth pit cover 80mm thick made of RCC (1:1.5:3) type A1 duly reinforced with 8mm dia TMT bar @ 100mm c/c both ways, one lifting handle made out of 10mm dia TMT bar 250mm long embedded in cover slab and cover, wire, copper lugs, etc, mest, charcoal and common salt in alternate layer of 15cm thick including taking down old unserviceable earth plate complete all as specified & as directed. Note: Each protection pipe and earthing lead upto and including 7.5 meter length is deemed to be included in the quoted rate of this item

Dismantling/opening up existing ceiling fan size of 1200 mm sweep, taking out all burnt/damaged windings insulating materials & cleaning internally as well as externally, rewinding the fan motor with super enamelled copper wire as per existing size/specification, replacement of complete insulating materials, varnishing drying up, cleaning & greasing of bearing/buses using new grease, reassembling and testing and transporting back to site and refixing to original position. The rates quoted by the contractor shall deemed to include replacement of defective slip pin and roller rubber if worn out and connecting wire of 3 core 1.5 Sqmm pvc flexible copper wire upto 1.0 mtr complete all as specified & as directed.

Ditto- all as per item No 2 here-in-before but exhaust fan size 450 mm sweep.

Ditto- all as per item No 2 here-in-before but exhaust fan size 230/300 mm sweep.

Ditto- all as per item No 2 here-in-before but wall mounted fan 300 mm sweep.

Taking down connecting and dismantling of ceilings fans of sweep 1200mm / 1400mm including fan blades down rod, coupling, decorative caps, condenser housing, stator and rotor for inspection and replacement of defective parts complete all as specified including complete overhauling/greasing reassembling and testing to achieve satisfactory performance, refixing after repair complete all as specified and directed by Engineer-in-Charge for the following stated below as (a) & (b) :- Note (a) Spare parts required shall be measured and paid separeately as supply only under relevant items of this schedule hereinafter. (b) Painting shall be measured & paid separeately. (c) Material required for overhauling such as grerase, oil, etc shall deemed to be included in rate quoted.

Complete all as item No 6 above but exhaust fan of size 450mm size sweep.

Complete all as item No 6 above but exhaust fan of size 230/300mm size sweep.

Supply only capacitor (ISI marked) 4 mfd Make :- Epcos / Usha / Keltron

Supply only capacitor (ISI marked) 2.5 mfd Make :- Epcos / Usha / Keltron

Supply only rubber bush for capacitor (as per Sample)

Supply only split pin (as per sample)

Supply only rubber reel (as per sample)

Supply only shackle for ceiling fan with nut and bolts (ISI marked)

Supply only ceiling fan canopy suitable for 15mm dia rod with fixing Nuts and Bolts as approved by Engr-in-Charge

Supply only fan blade suitable for 1200/1400mm sweep complete all as specified & as directed. (Make- As per sample)

Supply only exhaust fan blade suitable for 230/300/450mm sweep complete all as specified & as directed. Make:- As per sample

Supply only ball bearing/bush for exhaust fan/celing fan of any size complete all as specified and as directed. (Make : TATA/NBC/SKF) Note for item No 9 to 18:- Labour charges for taking out old spares & refixing of new spares shall deemed to be included in unit quoted rate of Item No 6, 7 & 8 here- in- before.

Material and labour for preparing ceiling fan surfaces for painting by removing/cleaning dust and deposited material and apply one coat of white enamelled paint by spray to fan blades, body and down rod, canopy of ceiling fans complete all as specified and as directed

Taking out unserviceable ceiling fan, supply and replacement with ceiling fan 230V, 50 Hz, AC 1200 Sweep, min air delivery CFM with service value 6.00 BEE, five star rated with brushless direct current motor (BLDC) complete with hanging arrangement by down rod along with steel wire rope for additional safety in ceiling fan with all allied accessories and connecting up with three core 0.75 sqmm PVC insulated copper conductor cable complete all as specified and directed. Make : Crompton/Havells/Bajaj/Polycab

Taking down deteriorated louvers and supplying and fix new louvers fixed type made out of 16SWG GI sheet with machine pressed cut for horizontal ventilation, bending into shape of size 45cmx45cm (outer) with 20x 3mm flat iron based size of 45cmx45cm complete all as specified and directed.

Material and labour for preparing exhaust fan of any size surfaces for painting by removing/cleaning dust and deposited material and applying one coat of grey enamelled paint by spray to exhaust fan body, blades and louvers complete all as specified and as directed.

Cutting hole in existing concrete or brick wall suitable for fixing 300mm/450mm sweep exhaust fan making good the hoel including proper internal plaster work and surfaces finish in side and outside the hole as per site requirement complete all as specified and directed.

Taking out unserviceable exhaust fan, supply and replacement with exhuast fan, 3/4 blade heavy duty double ball bearing, 230V, 50Hz, 300mm sweep having power input 70W speed 1440RPM, with protective bird guard including connection as required at site with flexible copper cable complete all as specified and directed. Make :- Crompton/Havells/Bajaj/Polycab

Inspection and maintenance of water heater (Geysers) of capacity, 25 ltrs to 50 litres including performing the following task at various location (a) Removing the heating plate assembly and descaling the heating element/pipe either by use of acid or equa cleaner to make it functional complete. (b) Checking and setting of thermostat between 70 to 80 degree Celsius. (c) Check working of NRV stop cock, pressure release valve and servicing carefully to make it functional. (d) Repairing of earthing connection, power switch, socket connection replacement of indicator lamp to make it functional. (e) Examine water leakage and rectifying as required and replacement of rubber washer gasket etc to make it functional. (f) Inspect over flow vent pipe, safety valve and remove blockage if required to make it functional.

Supply & fixing in repair of heating element of rating 2 KW to geyser above 25 and upto 50 litres capacity, any type, complete all as specified and as directed.

Supply & fixing in repair of heating element of rating 1.5 KW to geyser upto 25 capacity, any type, complete all as specified and as directed.

Supply & fixing in repair of the thermostat (adjustable type) suitable for upto 50 litres capacity of geysers complete all as specified and directed. (Make:- Indfoss/Renutrol/Siemens/Daspass/Honeywell)

Supplying and fixing in replacement of geyser plate assembly suitable for 25 to 50 litres capacity geysers, of brass with inlet, outlet pipe, drain plug, thermostat chamber fixing heating element gasket nut, bolt etc are fixing the assembly to make it functional complete all as specified and as directed.

Supply & fixing in repair of flexible PVC pipe connection, heavy duty nylon thread reinforced 15 mm dia, 450 mm long with brass union at both ends for 15 mm dia pipe complete all as specified and as directed. (Make :- Prayag/Polytaff/Superme/Prince)

Supply & Fixing in repair gasket of thickness 5 mm for geyser assembly of 08 holes/09 holes complete all as specified & directed..

Supply & Fixing in repair metal clad top & socket single phase complete all as directed. (Make :- Schneider/Legrand/ABB/Siemens/L&T)

Supply & Fixing in repair non return valve for geyser, make as per site requirement complete all as specified and as directed.

Supply & Fixing in repair fastner mild steel 100/150/200 mm long complete all as specified & directed.

Dismantling/taking out the geyser assembly & copper tank and making soldering & brazing of tank and fixing the same in the geyser of any cap complete all as specified and directed.

Supply and fixing of Galvanised iron pipe medium grade 20 mm bore with necessary fittings such as tees, elbows, bends, reducers, unions etc fixed along wall/ floor/roof incl covering with insulation all around with 25mm thick bonded mineral wool preformed 'SNAPON' pipe sections of density 144 KG/Cum conforming to IS 9842 as directed of rock wool/ mineral wool, chicken mesh and cladding with 26 SWG alum sheet incl chasing/cutting of wall as required including taking down old serviceable one complete all as specified and as directed. Make of GI pipe :- JINDAL STEEL/ PRAKASH/ TATA/ OSWAL

Supply and fixing in repairs Hot water tap of brass/gun metal 15 mm bore complete all as specified and as directed. Make :- Zoloto / Leader / UpadhyayGEM/ VENUS/ AUDCO

Supply & Fixing in repair LED recessed mounting square slim LED down lighter 36 Watt for AS/GB/POP ceiling 2'x2' size complete with internally prewired and connecting up with twin core flexible copper conductor cable of suitable size including taking down of old unserviceable one complete all as specified and directed. Make :- Havells /Phillips / Surya Roshni Ltd / Bajaj/Crompton.

Supply and fixing in repairs miniature circuit breaker (MCB) single pole and neutral 240 volts, 40 Ampere current rating, 'C' curve, 10 KA breaking capacity complete all as specified and directed. Make :- Legrand / Havells / Indo Asian / ABB / L&T (LEXIC))

Ditto- all as per item No 39 above but for SPN 6 to 32 Amps current rating.

Ditto- all as per item No 39 above but for SP 6 to 32 amps current rating.

Ditto- all as per item No 39 above but for 'B' curve SP 40 Amps current rating.

Supply and fixing in repairs sheet metal enclosure, single pole and neutral with two pin earth plug and socket complete with one single pole MCB 20 Amp, 240 volts fixed with half grouting on wall complete all as specified and directed. Make :- Legrand / C&S / Havells / Siemens / ABB

Ditto- all as per item No 43 above but for MCB 32 Amps current rating.

Taking down carefully existing surface/concealed unserviceable copper/Aluminium point wiring (light, fan socket or power) complete with fittings such as switches, ceiling rose, lamp holder, regulators, sockets, F/Tube/Sketch light fittings, wooden terminal box, plastic laminated sheet cover, from Teak Wood batten including Teak Wood batten or PVC conduits complete all as specified & as directed.

M & L for point wiring using 1.50 sqmm size FRLS, PVC insulated, unsheathed 1100 volts grade single core multi-stranded copper conductor cable in proper colour coding drawn into and including non metallic rigid PVC conduit medium grade (not less than 20 mm dia) for wall and 25mm PVC medium grading grade casing and caping in the ceiling wherever required with and including its all necessary fittings and accessories fixed concealed, sunk cast iron or 1.2 mm thick pressed steel terminal box for mounting fittings and covered with 3 mm thick white bakelite / laminated hard glossy surface sheet top cover fixed with brass screws and cup washers including one continuous run of PVC insulated (green colour) 1.50 sqmm size FRLS stranded copper conductor cable as in earth wire and connecting all metal parts to common earth dolly for one light / Fan / exhaust fan / Bell point controlled by one, one way switch complete all as specified & directed by Engr-in-Charge. Make of cable:- NICCO / FINOLEX / RR KABEL/ HAVELL'S/ POLYCAB / KEI INDUSTRIES LTD Make of PVC Casing & Caping :- FINOLEX / PAYAL/KALINGA/ PRESTO PLAST Make of Conduit:- FINOLEX /POLYCAB/KALINGA/ PRESTO PLAST

All as per item No. 46 above but for one 5 pin 5/6 Ampere socket outlet point controlled by one, one way switch on the same board complete all as specified and directed by Engr-in-Charge.

All as per item No. 46 above but for one 5 pin 5/6 Ampere socket outlet point controlled by one, one way switch on independant board complete all as specified and directed by Engr-in-Charge.

Material & Labour for point wiring for one 15/16 Ampere socket outlet independent point using 2.50 sqmm FRLS size (Nominal cross sectional area), PVC insulated, unsheathed 1100 volts grade single core multi-stranded copper conductor cable in proper colour coding drawn into and including non metallic rigid PVC conduit medium grade concealed (not less than 25 mm dia) for wall and 25mm PVC medium grading grade casing and caping in the ceiling wherever required with and including its all necessary fittings and accessories fixed concealed, sunk cast iron or 1.2 mm thick pressed steel terminal box for mounting fittings and covered with 3 mm thick white bakelite / laminated hard glossy surface sheet top cover fixed with brass screws and cup washers including one continuous run of PVC insulated (green colour) 2.50 sqmm FRLS size stranded copper conductor cable as in earth wire and connecting all metal parts to common earth dolly complete all as specified and directed. Make of cable:- NICCO / FINOLEX / RR KABEL/ HAVELL'S/ POLYCAB / KEI INDUSTRIES LTD Make of PVC Casing & Caping:- FINOLEX / PAYAL/KALINGA/ PRESTO PLAST Make of Conduit:- FINOLEX /POLYCAB/KALINGA/ PRESTO PLAST

Supply & Fixing in repair socket out let 2 in 1, 3/5 Pin, 15/16 Ampere, 230V AC, flush type complete all as specified and as directed. Make :- Anchor / Cona / Kinjal / Havells

Supply & Fixing in repair ceiling rose, 3 phase, PVC / polycarbonate, surface type, 65mm x 50mm, insulated body, three terminals complete all as specified and as directed. Make :- Anchor / Ess Ess Kay / Havells/ Cona

Supply & Fixing in repair modular switch one module, 15/16 Amp, one way, 230 volts AC complete all as specified and as directed by Engr-in-Charge. Make :- Anchor / Cona / Crabtree / Legrand / Indo Asian (Glint)

Supply & Fixing in repair of modular socket outlet (two module) 5/6 amps, 2 in 1, 2 & 3 pin combined, 230 volts AC complete all as specified and as directed by Engr-in-Charge. Make :- Anchor / Cona / Crabtree / Legrand/ Indo Asian (Glint)

Supply & Fixing in repair of modular socket out let (two module), 2 in 1, 3 Pin suitable for 5/6 Amp and 3 Pin suitable 15/16 Amp combined, 230 volts AC complete all as specified and as directed by Engr-in-Charge. Make :- Anchor / Crabtree / Legrand / Indo Asian (Glint)

Supply & Fixing in repair of electric ding dong bell, 230 volt AC, single pole, complete all as specified and as directed by Engineer-in-Charge. Make :- Anchor / Cona / Wipro / Bajaj/Havells

Supply & Fixing in repair of flush type bell push, 5 Amps complete all as specified and as directed by Engr-in-Charge. Make :- Anchor / Cona / Kinjal / Havells

Supply & Fixing in repair of lamp holder, PVC/polycarbonate type, insulated body with back plate of batten fitting complete all as specified and as directed. Make :- Anchor / Ess Ess Kay / Plaza / Havells

Supply & Fixing in repair of stepped type 5 steps 100 watts electronic fan regulator flush type on the existing phenolic laminated sheets etc as required all as specified and as directed. Make :- Anchor / Havells / Usha / Crompton / Bajaj

Supply & Fixing in repair of Modular Fan regulator step type, 1 Module size complete all as secified and as directed. Make:- Havells / Legrand/ Crabtree/ Anchor

Taking down unserviceable sub main wiring of any type and any size including wooden batten, PVC conduit or casing caping complete all as specified and as directed.

Material and labour for sub main wiring with two runs of single core 4.0 Sqmm (nominal area) PVC insulated copper conductor FRLS (conforming to IS-694), stranded, unsheathed 1100 volts grade in PVC Conduit (heavy grade) of 20mm dia or more dia with all fittings and accessories surface type including one run 4.0 Sqmm single core unsheathed stranded copper conductor cable FRLS (conforming to IS-694) as earth wire complete all as specified and as directed by Engr-in-Charge. Make of cable:- NICCO / FINOLEX / RR KABEL/ HAVELL'S/ POLYCAB / KEI INDUSTRIES LTD Make of Conduit:- FINOLEX /POLYCAB/KALINGA/ PRESTO PLAST) Note : (a) Two run of 4.00 sqmm copper cable and one run of 4.0 sqmm copper cable (earth wire) alongwith PVC conduit measured as one unit length. (b) Extra length of cable required for connetion to DBs shall deemed to be included in the unit quoted rate and shall not be measured separately. (c) Earth wire shall run inside the conduit. (d) Suitable colour code of wire shall be maintained for phase / neutral / earth).

Material and labour for sub main wiring with two runs of single core 6.0 Sqmm (nominal area) PVC insulated copper conductor FRLS (conforming to IS-694), stranded, unsheathed 1100 volts grade in PVC Conduit (heavy grade) of 20mm dia or more dia with all fittings and accessories surface type including one run 6.0 Sqmm single core unsheathed stranded copper conductor cable FRLS (conforming to IS-694) as earth wire complete all as specified and as directed by Engr-in-Charge. Make of cable : RR Kable / Plaza / Finolex / Havells / Polycab. Make of Conduit:- FINOLEX /POLYCAB/KALINGA/ PRESTO PLAST). Note : (a) Two run of 6.00 sqmm copper cable and one run of 6.0 sqmm copper cable (earth wire) alongwith PVC conduit measured as one unit length. (b) Extra length of cable required for connetion to DBs shall deemed to be included in the unit quoted rate and shall not be measured separately. (c) Earth wire shall run inside the conduit. (d) Suitable colour code of wire shall be maintained for phase / neutral / earth).

Material and labour for sub main wiring with two runs of single core 10.0 Sqmm (nominal area) PVC insulated copper conductor FRLS (conforming to IS-694), stranded, unsheathed 1100 volts grade in PVC Conduit (heavy grade) of 25 mm dia or more dia with all fittings and accessories surface type including one run 10.0 Sqmm single core unsheathed stranded copper conductor cable FRLS (conforming to IS-694) as earth wire complete all as specified and as directed. Make of cable:- NICCO / FINOLEX / RR KABEL/ HAVELL'S/ POLYCAB / KEI INDUSTRIES LTD Make of Conduit:- FINOLEX / POLYCAB/KALINGA/ PRESTO PLAST) Note : (a) Two run of 10.00 sqmm copper cable and one run of 10.0 sqmm copper cable (earth wire) alongwith PVC conduit measured as one unit length. (b) Extra length of cable required for connetion to DBs shall deemed to be included in the unit quoted rate and shall not be measured separately. (c) Earth wire shall run inside the conduit. (d) Suitable colour code of wire shall be maintained for phase / neutral / earth).

Supply and fixing in repair of LED street light 45 W made out of pressure die cast luminaire comprising of epoxy powder coated hsg enclosed with 4mm thick toughened glass cover and matrix of power LEDs , inbuilt electronic driver with upto 4KV surge protection including connecting with PVC insulated sheathed cable of size 2 x 1.5 Sqmm copper conductor cable, fitted with adjustable pole adapter to enable on site tilt angle setting depending on road geometry in frame 45w mounted on MCPCB including taking down old unserviceable one complete all as specified and directed. Make : Crompton Greaves model No-LSTS-45-CDL-1 or equivalent model of Bajaj / Phillips / OSRAM

Supply and fixing in repair security light fitting bracket, 1.5 mtr long made out of galvanized iron pipe of 40 mm dia size, light grade complete with nut, bolts, washer etc inclusive of one primer coat, one under coat and one finishing coat of silver paint including taking down old unserviceable one complete all as specified and directed. (Make of GI pipe- JINDAL STEEL/ PRAKASH/ TATA/ OSWAL)

Supply and fixing in repair MCB Metalica Distribution board, Double door, concealed flush to wall for mounting MCBs, factory made , conforming to IS : 13032 fabricated out of CRCA sheet not less than 1.20 mm thick fitted with DIN channel, neutral link and 200 Amps rated bus bar. DBs shall be semi glossy finished with epoxy polyster based powder paint sprayed and backed at high temperature , between powder paint process to ensure smooth finish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of same make as MCBs, DB shall also be provided with lable marking indicating the incoming and outgoing circuits on all ways as specified , the DBs shall be of IP 42 protection class for the following complete all as specified and as directed.

TPN 4 way, 415 Volts TPN Metalica Distribution Board. Make :- L & T/Legrand/ Siemens/ ABB/ Schneider

SPN 12 way, 230 Volts SPN Metalica Distribution Board. Make :- L & T/Legrand/ Siemens/ ABB/ Schneider

SPN 8 way, 230 Volts SPN Metalica Distribution Board. Make :- L & T/Legrand/ Siemens/ ABB/ Schneider

SPN 4 way, 230 Volts SPN Metalica Distribution Board. Make :- L & T/Legrand/ Siemens/ ABB/ Schneider

Supply and fixing in repair of MCCB incommer distribution board VTPN 04 way with metal double door CRCA steel sheet surface, powder coated, IP-54 protection suitable for MCCB as incommer and MCB as outgoing, 415 Volt 3 phase complete with appropriate size copper busbar and neutral link complete including MCCB 160A, cutting chases to wall for fixing of DB and making good disturbed surface complete all as specified and as directed. Make:- Legrand/ L&T/ ABB/ Siemens/ Schneider

Supply and fixing in repair MCB TPN, 40 to 100 Amp, 10 KA, 'C' curve type with overload and short circuit protection incl making necessary DB connection, testing and commissioning complete all as specified and as directed. Make:- Legrand/ L&T/ ABB/ Siemens/ Schneider

Supply and fixing in repair LED light fitting 1x9W/ 1X10W bulkhead luminaires including LED light driver holder, connecting up with three core flexible copper conductor cable of suitable size including taking down old unserviceable one complete all as specified and as directed. Make :- Philips/ Crompton Greaves/ Bajaj/ Osram

Supply, laying and testing in replacement of cable XLPE insulated screened PVC bedded, galvanized steel strip , electric power cables (heavy duty) with Aluminium Conductor of size 10 Sqmm 2 Core, 1100 Volts grade including cable glands, lugs, Saddling on wall (if required), nuts, bolts and washers of suitable size including taking out old unserviceable cable complete all specified and as directed. Make:-Polycab/Gloster/Havells/Plaza/Finolex.

All as per item sl No 74 but 16 sqmm, 4 core.

All as per item sl No 74 but 35 sqmm, 4 core.

Supply and fixing in repair of aluminium lugs suitable for 16 Sqmm suitable for Aluminium/Copper cables complete all specified and as directed. Make :- Dowells or of equivalent make)

Supply and fixing in repair of aluminium lugs of suitable for 25/35 Sqmm suitable for Aluminium/Copper cables complete all specified and as directed. Make :- Dowells or of equivalent make

Supply and fixing round shape LED fitting suitable for roof ceiling, 6 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, including connecting up with three core flexible copper conductor cable of suitable size including taking down old unserviceable one complete all specified and as directed. Make : - Philips/ Crompton Greaves/ Bajaj/ Osram

Supply & fixing retrofit LED lamp 7 watt complete all as specified and directed. Make :- Bajaj/Havells/Phillips/Cromption/Wipro

Supply and fixing in repairs modular White cover plate with frame, 3 module size as per site requirement complete all as specified and as directed. Make :- Anchor / Cona / Crabtree / Legrand

Supply and fixing in repairs modular White cover plate with frame, 4 module size as per site requirement complete all as specified and as directed. Make :- Anchor / Cona / Crabtree / Legrand

Supply and fixing in repairs modular White cover plate with frame, 6 module size as per site requirement complete all as specified and as directed. Make :- Anchor / Cona / Crabtree / Legrand

Supply and fixing in repairs modular White cover plate with frame, 8 module size as per site requirement complete all as specified and as directed. Make :- Anchor / Cona / Crabtree / Legrand

Supply and fixing in replacement of modular metal flush box, 1.6 mm thick, 4 module,mounting in the wall for fitting cover plate with frame on switch/socket complete all as specified and as directed. Make :- Anchor / Cona / Crabtree / Legrand

Supply and fixing in replacement of modular metal flush box 1.6 mm thick, 6 module,mounting in the wall for fitting cover plate with frame on switch/socket complete all as specified and as directed. Make :- Anchor / Cona / Crabtree / Legrand

Supply and fixing in repairs PVC Gang Box suitable for one No 15 Amps Switch and Socket complete all as specified and as directed. Make :- Presto Plast/Pressfit/Polyplast.

Supply and fixing in repair of PVC casing & caping of size 20 mm inclusive of all fittings such as tees, bends, elbow, etc and all fixing accessories such as couples,PVC Rawal Plugs, saddles, etc including making surface good as original by plastering and whitewash/ colour/ distemper etc including taking down old unserviceable one complete all as specified and as directed. Make:- Finolex/ Payal/ Kalinga/ Presto Plast).

Supply and fixing in repair LED light fitting 1x10 W (2 feet), mirror type with high out put diffuser , 220A AC, decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing in repair Post top lantern of 36 Watt, LED light on RCC post with all accessories internally pre-wired and including connecting up with twin core twisted flexible cable of 0.75 Sqmm, 3 core copper conductor to light fittings including taking down old unserviceable one complete all as specified and as directed. Make:- Crompton Greaves/ Philips/ Bajaj/ Osram

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for laying of cables/ pipes, etc. and not exceeding 10 Sqm on plan and getting out in hard/ dense soil complete all as specified and as directed.

Material and labour for sand cushioning to the full width of trenches for protection of cables including spreading watering and consolidation complete all as specified and as directed. (Note:- Only punned down volume of sand to be measured).

Returning filling including spreading levelling, watering and well ramming in layers not exceeding 25cm in soft/loose soil complete all as specified and as directed.

Removing excavated soil to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed.

Supply and laying of sub Class 'B' old size bricks designation 75, for cable protection in trencehs completed all as specified and directed by Engineer-in-Charge

Checking and attending day to day complaints by means of finding of fault, repairing/rectifying the electric defects/faults related to internal wiring,switch, socket, light fittings, fan, Tightening the loose connections and all accessories and fixtures maintained by MES at DIPAC complete all as specified and directed. NOTE :- (i) This item covers only cost of labour for attending complaints and taking down of old material. (ii) Item required to be replaced under this item shall be measured and paid separately as supply only items. (iii) Complaints noted NO light shall be attended immediately from 0800 Hrs upto 2200 HRS without fail, failing which recovery of rate Rs 240/- per complaint per day shall be effected from the RARs/FB. (iv) Minor items such as PVC wire of any size as per requirement upto 1.0 mtr length, thimble, electric tape etc shall be deemed to be included in the quoted rate of this item. (v) The complaints shall be attended and defects shall be rectified within 08 Hrs commencing from date and time of notifying the complaint slip failing which a penalty of Rs 120/ per complaint per day shall be leived/imposed on the contractor and recovery shall be made from his dues. (vi) Contractor shall arrange suitable T&P incl necessary from work and scoffolding and safety measures to make it functional complete all as specified and directed. (vii) Contractor or his rep will report daily at 0900 Hrs at complaint cell for collection of complaint from the concerned JEs incharge. In case after checking and attending if it is not possible to rectify the defects within 08 Hrs, the fact shall be brought to the notice of Engr-In-Charge by the contractor/his rep immediately. If Engr-In-Charge is satisfied with contractor's view, no recovery will made on this account. Discretion of Engr-In-Charge shall be final and binding. (viii) Approx 4 to 5 complaints are received per day. (ix) The electrician has to reach the site within 45 minuites after receipt of complaint. failing which recovery of rate Rs 500/- per complaint per day shall be effected from the RARs/FB. (x) The electrician should be in possession of mobile and two wheeler for uses of communication and mobility. (xi) The contractor will maintain complaint docket/complaint slip for each complaint. after rectification of fault/complaint on complaint slip duly signed by user and JE same will be handed over to MES Rep.

Supply only switch piano, flush type, ivory finish 5/6 Ampere single pole, one way complete all as specified and as directed. (Make :- Anchor / Cona / Kinjal / Havells)

Supply only socket out let 2 in 1, 3/5 pin, 5/6 Ampere, 230V AC, flush type complete all as specified and directed. (Make :- Anchor / Cona /Kinjal / Havells)

Supply only switch piano, flush type, ivory finish 15/16 Ampere single pole, one way complete, all as specified and as directed. (Make :- Anchor / Cona /Kinjal / Havells)

Supply only modular switch one module, 5/6 Amp, one way, 230 volts AC complete all as specified and directed. (Make :- Anchor / Cona / Crabtree / Legrand / Indo Asian (Glint)).

Supply only Basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver LED tube light fitting 20 watt including LED tube, 230 volt complete all as specified and directed. (Make :- Havells cat part No LUMILINEBS9WLED830SPCWH or equivalent model of make Phillips / Surya Roshni Ltd / Bajaj/ Crompton Greaves/ C & S Electric)

Supply only Basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver LED tube light fitting 9 watt including LED tube, 230 volt complete all as specified and directed by Engr-in-charge. (Make :- Havells cat part NoLUMILINEBS9WLED830SPCWH or equivalent model of make Phillips / Surya Roshni Ltd / Bajaj/ Crompton Greaves/ C & S Electric) Note for Item no 97 to 102: Labour charges for replacement of materials shall deemed to be included in unit quoted rate of Item No 96 here- in- before.

Supply and fixing Service cable of aluminium conductor of 10 Sqmm 2 core size , PVC insulated, unarmoured including taking down of old unserviceable cable complete all as specified and as directed. (Make:- Polycab/Gloster/Havells/Plaza/Finolex.)

Material & Labour Cutting channels, grooves or rebates exc 15 cm but n exc 30cm girth and trimming surface and making good the disturbed surfaces of wall/ ceiling with cement mortar, white cement and painting work to match the existing surfaces of walls complete all as specified and directed.

Material & Labour for applying two coat of Steel based paint on Steel tubular swaged poles of Street Light of ant description up to including 9m overall length including preperation of old painted surface of Steel poles complete all as specifie and as diredted by Engineer-in-Charge Note (Colour of Paint as directed by Engr-in-Charge. (Make of paint and primer :- Asian/Berger/ Jenson & Nicholson/Shalimar)

Shiv Enterprises

Tushar engineers

KRISHANA ELECTRIC WORKS

M/S ANIL KUMAR

MRITUNJYA ASSOCIATES

Surjit and Sons

Haryana EngineerService

ASHUTOSH BUILDERS

GILL ENGINEERS

BUSINESS TEK INDIA