PROVN OF GUARD LIVING CAMP NEAR TCP_1 AND SPECIAL REPAIRS TO DRAINAGE AND GUTTER LINE NEAR BLDG NO P_78 IN GAGAN VIHAR AT RMS UNDER AGE BR_I OF GE 868 EWS

Amount

Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches etc complete all as specified and directed by Engr-in-Charge.

Demolition of reinforced cement concrete in ground floors and pavings n.exc 15 cm thick above or below ground level complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete in ground floors and pavings n.exc 15 cm thick above or below ground level complete all as specified and directed by Engr-in-Charge.

Demolition and breaking up drain pipes (salt glazed, stoneware, AC or reinforced concrete/PVC pipe) set in cement mortar 150 /110 mm dia fixed in position complete all as specified and directed by Engr-in-Charge.

M&L for surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in soft/ loose soil complete all as specified and directed by Engr-in-Charge.

M&L for excavation in trenches n.exc 1.5m wide and n.exc 1.5m in deepth; for foundation etc or for shafts, wells, cesspits, manhole, pier holes, etc n.exc 10 Sqm on plan and n.exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed by Engr-in-Charge.

M&L for PCC 1:4:8 type D-2 (using 40mm graded agg) as in foundation, filling and mass concrete complete all as specified and directed by Engr-in-Charge.

M&L for mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-Charge.

All same as per item No 8 above but 6mm to 8mm dia complete all as specified and directed by Engr-in-Charge.

All same as per item No 8 above but 5mm dia and over and including 10mm dia in stirrups spacers and binders complete all as specified and directed by Engr-in-Charge.

M&L for RCC Nominal Mix Type B1 1:2:4 (using 20 mm graded stone aggregate) as in foundation, including rafts, footings, foundation beams; plinth beams; bases for coloumns, etc basement slabs under reamed piles and mass concrete complete all as specified and directed by Engr-in-Charge.

M&L for PCC 1:2:4 type B-1(20mm grade stone aggregate) as in coping ,benching,water troughsand the likes incl weathering slightly rounded and chamfered and throating etc complete all as specified and directed complete all as specified and directed by Engr-in-Charge.

M&L for RCC Nominal Mix Type B1 1:2:4 (using 20 mm graded stone aggregate)as in columns, pillars, piers, posts and struts complete all as specified and directed by Engr-in-Charge.

M&L for RCC Nominal Mix Type B1 1:2:4 (using 20 mm graded stone aggregate) slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engr-in-Charge.

M&L for RCC Nominal Mix Type B1 1:2:4 (using 20 mm graded stone aggregate) as in chajjas complete all as specified and directed by Engr-in-Charge.

M&L for RCC Nominal Mix Type B1 1:2:4 (using 20 mm graded stone aggregate) as in beams, cantilvers, bressummers, lintels over 1.5m span complete all as specified and directed by Engr-in-Charge.

M&L for providing pre cast reinforced cement conccrete type B1,1:2:4 (20 mm grade Aggregate) in landings and similar articles with plane faces set in cement mortar 1:4 complete all as specified complete all as specified and directed by Engr-in-Charge.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to battercomplete all as specified and directed by Engr-in-Charge.

Use and waste of formwork to sides of pillars posts, struts, piers, columns and stanchions finished the suface rough complete all as specified and directed by Engr-in-Charge.

Use and waste of formwork to sides and soffits of floors or roof beams, beams haunchings, girders,bressummers lintels, cantilevers, shelves including supports overhangs etc also splays between floors and beams etc complete all as specified and directed by Engr-in-Charge.

Use and waste of formwork to chajjas, troughts and similar items including edges complete all as specified and directed by Engr-in-Charge.

M&L form work with fair finished to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar work nexc 200mm thick (horizontal or sloping) complete all as specified and directed by Engr-in-Charge.

Supply only water proofing compound complete all as specified and directed by Engr-in-Charge.

M&L for brick work with sub class `B' bricks straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed by Engr-in-Charge.

Material and labour for brick work in cement mortar 1:4 with sub class `B' bricks straight or curved on plan exceeding 6m mean radius with old size bricks as in pillars complete all as specified complete all as specified and directed by Engr-in-Charge.

M&L for brick work with sub class `B' bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed by Engr-in-Charge.

S&F steel windows with side hung shutters including Box type hinges with steel handle and steel peg stay, complete with glazing bars, devetailed or welded complete all as specified and directed by Engr-in-Charge.

S&F steel windows with side hung shutters including box type hinges with steel handle and steel peg stay, complete without glazing bars, devetailed or welded complete all as specified and directed by Engr-in-Charge.

S&F ventilator with top hung shutter including hinges, steel peg stay complete complete all as specified and directed by Engr-in-Charge.

S&F 2nd calss HW 35mm thick factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9mm B.W.P commercial ply or 12mm verneered particle board wit commerical verneering on both faces. The size of rail and sitle as per IS:1003 (Part I) kiln seasoned and chemically pressure treaded complete all as specified and directed by Engr-in-Charge.

S&F 35m thick factory made glazed and skeleton shutter open rebated and prepared to receive glass gauge etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitered beads or clearing glass etc, size of members of shutters as specified in SSR part I section 8 clause 8.20 (a) of IInd class hard wood (Shisham) complete all as specified and directed by Engr-in-Charge.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S square tube, suppling and fixing in opening as per specification and drawing complete all as specified and directed by Engr-in-Charge.

S&F factory made solid panel PVC door shutter 30mm thick (style).consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with eat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement suppling & fixing in the frame at site as per specification and drawing complete all as specified and directed by Engr-in-Charge.

S&F 3mm thick figured glass, pin head type and glazing with oil putty in squares n.exc 0.5 Sq.m in each pane complete all as specified and directed by Engr-in-Charge.

S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed by Engr-in-Charge.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm complete all as specified and directed by Engr-in-Charge.

S&F 300mm door spring ordianary rat taill rod pattern springs including roller and roller plate complete complete all as specified and directed by Engr-in-Charge.

S&F 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed by Engr-in-Charge.

S&F 150mm extruded aluminium alloy handles fabricated type anodised complete all as specified and directed by Engr-in-Charge.

S&F 100mm medium weight butt hinges cold rolled mild steel complete all as specified and directed by Engr-in-Charge.

S&F 200mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed by Engr-in-Charge.

S&F 300mm 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and siding bolts of extruded sections or cast aluminium alloy complete all as specified and directed by Engr-in-Charge.

M&L for hardcore of gauge n.exc 63mm, deposited, spread and levelled in layers n.exc 15cm thick, watered and rammmed to a true surface complete all as specified and directed by Engr-in-Charge.

M&L for PCC 1:5:10 type E-2 (using 40mm graded agg) as in foundation, filling and mass concrete complete all as specified and directed by Engr-in-Charge.

M&L 40 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded stone agg) as damp proof course to horizontal or vertical surfaces including necessary form works, applying evenly a coat of blown type bitumen at 1.50 kg per sqm and blinding with clean dry sand @ 0.05 cum per sqm including 150 micron thick polythene film laid on a coat of bitumen primer @ 0.30 to 0.50 kg per sqm complete complete all as specified and directed by Engr-in-Charge.

M&L PCC 1:4:8 type D-2 75mm thick as in sub base of floor complete all as specified and directed by Engr-in-Charge.

M&L for non skid coloured joint free tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exc 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed 15mm thick in CM 1:6 all as directed complete all as specified and directed by Engr-in-Charge.

Same as per ser No 47.00 but on vertical surfaces such as skirting , dado risers to steps over and including 10 mm thick bedding layer in CM 1:4 , set and jointed in neat cement slurry and pointed in white or coloured cement to match all as directed complete all as specified and directed by Engr-in-Charge.

S&F non-skid coloured ceremic tiles 7 to 8 mm thick (Square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floors etc set and jointed in neat cement slurry and pointed in neat cement slurry and pointed in white or coloured cement to match the existing surfaces including 15mm thick screed bed or bedding layer in cement mortar 1:6 for fixing of tiles complete all as specified and directed complete all as specified and directed by Engr-in-Charge.

M/L glazed ceremic tiles 200x300x7 mm in dado set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles including 10mm thick cement mortar 1:4 for fixing of tile complete all as specified and directed complete all as specified and directed by Engr-in-Charge.

M&L for 75mm thick PCC in 1:3:6 type C1 (using 20mm graded agg ) as in plinth protection/path finished the surface even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L for PCC 1:3:6 type C-2 (40mm grade stone aggregate) as in bed to 160 mm dia SGSW /PVC pipes including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed by Engr-in-Charge.

Extra for forming fair finished surfaces of drain or channels, inner girth 30 cms, using extra cement including forms, moulds mitred/ stopped ends etc., complete all as specified and directed by Engr-in-Charge.

M&L for rendering 10mm thick plaster in CM 1:6 on fair faces of brick or concrete work finished the surface even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M & L rendering 15mm thick on cement mortar 1:4 brick or concrete work finished the surface even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished fair and even without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L for rendering 5mm thick plaster in CM 1:3 on fair faces of brick or concrete work finished even and smooth without using extra cement as in ceiling complete all as specified and directed by Engr-in-Charge.

M&L for Neeru finish to plastering as specified all as specified.

M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper of approved shade/tint over a coat of primer on walls all as specified & directed by Engineer-in-Charge complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new wall surface and two coats of cement base paint on walls complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new ceiling surface and two coats of cement base paint on ceiling complete all as specified and directed by Engr-in-Charge.

S&F 15mm dia bore tube medium grade galvanised with all fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed by Engr-in-Charge.

S&F 15mm bore dia bib taps cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed by Engr-in-Charge.

S&F 15mm dia bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed dwon high pressure, with or wothout lettered `Hot' or `Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed by Engr-in-Charge.

S&F CP angle cock 15mm cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed by Engr-in-Charge.

S&F Vitreous China wash basin white flat back size 550x400mm excluding taps chain and plug and procelain stopper but including brackets including PVC waste pipe 32 mm complete all as specified and directed by Engr-in-Charge.

S&F Vitreous China squatting pan, `Orissa' pattern size 580 x 440mm white with integral foot rests (excluding flushing cistern and flush pipe) including provision of lime concrete bedding compete all as specified and directed by Engr-in-Charge.

S&F vitreous china half stall urinal flat back, size of 465 x 355 x 265mm (minimum) white, with grating and union for discharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia complete all as specified and directed by Engr-in-Charge.

S&F 1000 ltr capacity ratational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as per specified in SSR Part I complete all as specified and directed by Engr-in-Charge.

S&F ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed in 20mm dia bore pipe complete all as specified and directed by Engr-in-Charge.

Supply pnly 32 mm waste coupling of PTMT (half or full threaded) complete all as specified and directed by Engr-in-Charge.

S&F Grating doom 100mm dia of PTMT (min wt -25gms) complete all as specified and directed by Engr-in-Charge.

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed by Engr-in-Charge.

Supply only flush pipe of polyethylene of low or high density of PVC 32mm dia for low level cistern complete all as specified and directed by Engr-in-Charge.

S&F PVC 10 ltrs valveless syphonic action type flushing cistern low level, white, with inlet ball valve float and handle including brackets complete all as specified and directed by Engr-in-Charge.

S&F towel rail 450mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (min wt - 170 gms) complete all as specified and directed by Engr-in-Charge.

S&F 100mm cast iron sanitary connections socket to fit WC out let complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new wooden of wood based surface of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new steel surface of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a red oxide primer complete all as specified and directed by Engr-in-Charge.

S&F 15 mm dia stop valve fancy type CP with crutch or butterfly handle complete all as specified and directed by Engr-in-Charge.

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall/floor complete all as specified and directed by Engr-in-Charge.

Suuply & fix 160mm dia PVC (SWR) pipes single/double socketed in any length with rubber ring joints, laid in trenches or in floors and jointed complete all as specified and directed by Engr-in-Charge.

Suuply & fix 110mm dia PVC (SWR) pipes single/double socketed in any length with rubber ring joints, fixed to walls complete all as specified and directed by Engr-in-Charge.

S & F 110mm dia PVC (SWR) branch piece, single (single Y equal or unequal) complete all as specified and directed.

S&F 75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall/floor complete all as specified and directed by Engr-in-Charge.

S&F of 110mm dia PVC (SWR) bends complete all as specified and directed by Engr-in-Charge.

S&F 75mm PVC(SWR) bends any radius with adess door complete all as specified and directed by Engr-in-Charge.

S&F of 75dia PVC (SWR) Vent cowl complete all as specified and directed by Engr-in-Charge.

S & F 75mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F in repairs for 75mm bore dia pipe Stack clamps out of 50mm by 5mm flat iron & 16mm dia round iron stays, including bolts & nuts & securing ends of stay to wall or roof complete all as specified and directed by Engr-in-Charge.

S & F Pre-painted galvatume aluminum zinc coating GI vased corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed by Engr-in-Charge.

S & F Pre-painted galvatume aluminum zinc coating GI vased Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed by Engr-in-Charge.

S & F for 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) pre-Painted self embossed, textured designer board E-Board Classic to be fixed GI powder coated grid/section size 600mmx600mm with main runner 38x24x0.9mm thick ,cross tee 28.6x24x0.9 mm and wall angle 19x19xo.9 mm duly suspended with 4mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size etc complete all as specified.

S&F 150mm dia mild steel sheet eaves gutters of 1mm thick sheet, galvanised class 3, half round with rounded edges complete all as specified and directed by Engr-in-Charge.

S & F of steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS – 1161 – 1979 grade St – 240 complete all as specified and directed.

S&F mild steel screw bolts 11 to 15 mm dia (machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut nexc 5 cm long complete all as specified and directed by Engr-in-Charge.

S&F Plates (plain or chequered) channels. Square cut or notched ) (ordinary and counter sunk) forming holes, without any attachment of Fe-410-W (Gde-E-250 quality-A) complete all as specified and directed by Engr-in-Charge.

S&F bands, straps or stays , plain angle cleat or flat iron cleat or securing purlins to wood trusses or rafters, knee piece and similar small articles etc conforming to Fe-290 Gde E-165 complete all as specified and directed by Engr-in-Charge.

S&F in repairs for Draperly rod /Harrison rails of stainless steel of 20mm dia with fixing brackets , stops, rollers and rings etc.complete all as specified and directed by Engr-in-Charge.

S&F Brass chromium plated shower rose 125mm size complete all as specified and directed by Engr-in-Charge.

M&L Cement concrete 1:3:6 type C-1 (20 mm graded agg ) in surface channels and drains complete all as specified and directed by Engr-in-Charge.

Extra for forming fair finished drain or channel 30cm inner grith in cement concrete, using extra cement, including forms, moulds, mitred/stop ends etc complete all as specified and directed by Engr-in-Charge.

Removing excavation material n exc. 50m & deposited where directed at a level n exc. 1.5m above the starting point complete all as specified and directed by Engr-in-Charge.

Returning, filling in, including spreading, leveling, watering & well ramming in layer s not exc 25 cm complete all as specified and directed by Engr-in-Charge.

M&L of earth filling under floor well ramming including watering as required Spreading & leveling in layers n.exc. 25cm thick complete all as specified and directed by Engr-in-Charge.

Point wiring complete with two runs of 1.5 sqmm single core PVC insulated FR-LSH cable 1100 volts grade with multi-stranded copper conductors, drawn through and including PVC double locked Casing & caping including provision of 1.5 sqmm, FR-LSH, PVC insulated copper cable as earth continuity conductor connecting to earth dolly, including PVC rectangular box for mounting switches/sockets/regulators etc. with 3mm thick plastic laminated sheet cover of suitable size as required at site and 50 mm deep complete all as specified and directed by Engr-in-Charge. Make: finolex/Havells/RR Kabel/Richa. Make of caping/casing & PVC boxes: Prestoplast/finolex/Supreme.

One light/fan point controlled by one, one way switch complete all as specified and directed by Engr-in-Charge

One 3 pin socket outlet 5 Amp on the same board with other switches complete all as specified and directed by Engr-in-Charge

One 3 pin socket outlet 5 Amps on the independent board complete all as specified and directed by Engr-in-Charge

All as per item No.107.00 here-in-before but with 2.5 Sqmm for 3 pin 15 Amps switch socket point on independent board along with one run of 2.5 Sqmm copper conductor green in colour as earth continuity conductor connected to earth dolly complete all as specified and directed by Engr-in-Charge

M&L for Switch Piano, flush type single pole, one way 5 Amps complete all as specified and directed by Engr-in-Charge Make:- Plaza/SSK/Hager/Anchor

M&L for Socket outlet 2 in 1, 3 pin, 5A flush type complete all as specified and directed by Engr-in-Charge Make:- Plaza/SSK/Hager/Anchor

M&L for Switch Socket combination 2 in 1, 3 pin 5A/16A, 5 in 1 flush complete all as specified and directed by Engr-in-Charge Make:- Plaza/SSK/Hager/Anchor

M&L for stepped type electronic fan regulator 100 watt socket size flush type on the existing phenolic laminatied sheet etc complete all as specified and directed by Engr-in-Charge. Make: Plaza/SSK/Hager/Anchor

M&L for ceiling rose 3 terminal PVC/Polycarbonate isolated body with PVC round/squareblock complete all as specified and directed by Engr-in-Charge Make:- Plaza/SSK/Hager/Anchor

M&L for 20W LED, 4', Wall mounted LED batten, extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver.etc with all accessories internally pre-wired and fixing the same on and including two Nos PVC blocks and connecting up with flexible copper cable of size 0.75 Sq mm 3 core from ceiling rose to the light fitting complete all as specified and directed by Engr-in-Charge Make : Havells Cat No LHFYBYPNIA1W022 Regal (batten) & LHDLEFXD5LR020(LED Tube) or equivalent in Bajaj/Philips

All as per item No 114.00 above but 09 watt LED 2', wall mounted with polycarbonate housing/batten complete all as specified and directed by Engr-in-Charge Make : Havells Cat No LHEXBQP5IN1W009 or equivalent

M&L for Lamp holder , PVC/ Polycarbonate type with PVC round/square block incl 9 watt LED lamp suitable for lamp holder fittings complete all as specified and directed by Engr-in-Charge Make :- Plaza/SSK/Hager Make of Lamp :- Havells/Bajaj/Philips

M&L for LED 1x20W building Security light fitting, drawn through including GI bracket of 25mm bore light grade bent to shape and fixed on wall with metal fastners 2 Nos 10mm dia incl drilling holes as required and connecting up with flexible copper cable of size 0.75 Sq mm 3 core from ceiling rose to the light fitting complete all as specified and directed by Engr-in-Charge Make:-Havells Cat Pt No LHETBXU7PA6S020 or equivalent in Bajaj/Philips

S&F for Ceiling fan 1200mm sweep, 5 star rating including suitable size of fan hook and connecting up with three core twisted flexible copper conductor cable of suitable size upto ceiling rose complete all as specified and directed by Engr-in-Charge Make : Bajaj/ Usha/ Havells

S&F for fixing exhaust fan, metallic, AC single phase 230/240 volts of size 300mm swep with louvre shutter including anchor bolt of suitable size for fixing arrangement and connecting up with three core twisted flexible copper conductor cable of suitable size upto ceiling rose complete all as specified and directed by Engr-in-Charge Make : CG/Bajaj/ Havells

S&F water heater storage type, electric capacity 25 litres BEE 5 star rated including suitable size and length of PVC connection for hot and cold water and fixing arrangement complete all as specified and directed by Engr-in-Charge Make : CG/ Bajaj/ Havells

M&L for MCB Distribution board double door type SPN 8 way, sheet steel, powder coated, with bus bar neutral link & earth bar etc. and fixing MCBs of various rating capacity complete all as specified and directed by Engr-in-Charge Make:- Legrand Cat No 607711 or equivalent in ABB/Siemens

M&L for MCB SPN, 40 Amps, 230 volts, 50 Hz suitable for fixing in MCB DB 'C' series incl taking down complete all as specified and directed by Engr-in-Charge Make: Legrand Cat No 408636 or equivalent in ABB/Siemens.

M&L for MCB SP, 5 to 32 Amps, 415 volts, 50 Hz suitable for fixing in MCB DB 'C' seriescomplete all as specified and directed by Engr-in-Charge Make:- Legrand Cat No 408587-95 or equivalent in ABB/Siemens

Taking down LT UG cable/service connection of any size and M&L for laying of LT UG cable , XLPE insulated, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of 16 sq mm, 4 core complete all as specified and directed by Engr-in-Charge NOTE :- (i) Excavation and earth work, sand cushioning, cable protection cover, pipe etc. shall be measured and paid seperately under relevant items. Make: Havells/Polycab/Phinolex/Richa

M&L for fine river washed sand in trenches complete all as specified and directed by Engr-in-Charge Note: for measurement purpose punned down thickness shall only be taken

M&L for laying brick sub class 'B' old size burnt bricks for protection of size 230mm x 115mm x 75mm complete all as specified and directed by Engr-in-Charge

Supply and laying tubes light grade galvanised GI tubing with all fittings, fixed complete to walls/poles/laid in floors/trenchs/road crossing of size 40mm dia bore including taking out unsv GI tubing complete all as specified and directed by Engr-in-Charge Make: Jindal/Prakash surya/TATA

M&L for earthing complete with galvanized steel earth plate electrode of size 600x600x6mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4 mm dia as earth lead connectd by means of bolts, nuts, washers and check nuts all as shown in electrical plate No 3 of MES SSR Part-I, including testing on complete all as specified and directed by Engr-in-Charge. Note: (i) The unit rate shall also included for earth work in hard/ dense soil, PCC (1:3:6) type C1 with 10mm thick CI cover plate hinged to angle iron frame of suitable size, funnel with GI watering pipe 20mm dia Medium grade, GI protection pipe light grade 15mm dia and wire mesh complete in addition to item No 1 (a) to (e) of preamble (notes) under sub heading earthing, specified on Sl Page No 389 of MES SSR Part-II. (ii) Earthing lead and GI protection pipe beyond 7.5m will be measured and paid separately. (iii) Test points shall be made of GI strip 32x6 mm bridge type.

M/S Lucky Builders

VIHUTO YEPTHO

Shri H Kivigho Zhimo

SHRI MADAN SINGH

SK SINGH