SPECIAL REPAIR TO BLDG NO. P-273 AT DSOI UNDER GE (WEST) JABALPUR

Amount

Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation or for laying of pipe, cable etc, n. exc.10 Sqm on plan and n. exc. 1.5m in depth and getting out in hard/ dense soil complete all as specified and directed.

Excavating in trenches, not exceeding 1.5m wide and exceeding 1.5 m depth but not exceeding 3 m in depth for foundation or for laying of pipe, cable etc, n. exc.10 Sqm on plan and exceeding 1.5 m depth but not exceeding 3 m in depth and getting out in hard/ dense soil complete all as specified and directed.

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed.

Removing excavated soil exceeding 1.5 Km but not exceeding 5 Km and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Providing precast cement concrete louvres and jallies, 35-40 mm thick (measured solid)(1:2:4) type B-0 ( using 12.5 mm graded stone aggregate), set in cement mortar 1:4 , including all mouldings but excluding frame complete all as specified and directed. Note :- (Precast RCC frame shall be measured and paid for separately against Srl item No. 6 of this BoQ here-in-after)

M&L precast RCC (1:2:4) frame, Type B-1 using 20mm graded crushed stone aggregate for RCC jali, set in CM (1:4) complete all as specified and directed .

M&L for RCC design mix M-25 (using 20 mm graded crushed stone aggregates) as in foundations, footing, plinth beams, bases for columns, mass concrete and the like etc for boundary wall complete all as specified & directed. Note:- Reinforcement shall be measured & paid for separately under respective item of BOQ.

M&L for RCC design mix M-25 (using 20 mm graded crushed stone aggregates) as in columns, pillars, piers, posts and struts and the like etc; complete all as specified & directed. Note:- Reinforcement shall be measured & paid for separately under respective item of BOQ.

M&L for RCC design mix M-25 (using 20 mm graded crushed stone aggregates) as in Beams, cantilevers,bressummers, lintels over 1.5m span etc for boundary wall complete all as specified & directed. Note:- Reinforcement shall be measured & paid for separately under respective item of BOQ.

M&L for RCC design mix M-25 (using 20 mm graded crushed stone aggregates) as in Chullah hoods; stairways (except spiral staircases) including steps (square or spandril), string pieces, carriages, etc., complete, any section straight or winding, but excluding landings; RCC water tanks upto 1500 litres etc; complete all as specified & directed. Note:- Reinforcement shall be measured & paid for separately under respective item of BOQ.

M&L for RCC design mix M-25 (using 20 mm graded crushed stone aggregates) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified & directed. Note:- Reinforcement shall be measured & paid for separately under respective item of BOQ.

Use and waste of Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter surface fair finished complete all as specified and directed.

Use and waste of Formwork to sides of pillars, posts, struts, piers, columns and stanchions etc., for rough finished surface of concrete, complete all as specified and directed.

Use and waste of Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), for rough finished surface of concrete, complete all as specified and directed.

Use and waste of Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide surface, for rough finished surface of concrete, complete all as specified and directed.

Use and waste of Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc., for rough finished surface of concrete, complete all as specified and directed.

M&L for RCC M-20( Nominal Mix) using 12.5 mm graded stone aggregate as in chajja upto 4th story height and the like complete all as specified and directed. Note:- Reinforcement shall be measured & paid for separately under respective item of BOQ.

M&L for RCC M-20 (nominal mix) using 12.5 mm graded stone aggregate as in Fins, fascias, louvres, parapets, and railings exc. 60 cm in height, newels, balustrade, and the like complete all as specified and directed. Note:- Reinforcement shall be measured & paid separately under respective item of BOQ.

M&L for RCC M-20 (nominal mix) using 20 mm graded stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. Note:- Reinforcement shall be measured & paid separately under respective item of BOQ.

Use and waste of Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter , for rough finished surface of concrete, complete all as specified and directed.

Use and waste of Formwork to chajjas, troughs and similar items including edges etc., for rough finished surface of concrete, complete all as specified and directed.

M&L for brick work with sub class 'B' fly ash bricks, straight or curved on plan exc 6m mean radius built in CM (1:4) complete all as specified & directed.

M&L for brick work with sub class 'B' fly ash bricks, straight or curved on plan exc 6m mean radius built in CM (1:4) but except brick complete all as specified & directed. ( Note : Old serviceable bricks retrieved against dismantling shall be re-used.)

M&L for brick work with sub class B bricks, fly ash bricks, straight or curved on plan to any radius in half brick thick walls built in CM (1:4) complete all as specified and directed

Supply only water proofing compound (liquid) ISI marked of make as approved by GE complete all as specified & directed.

Taking down Chowkhats or frame with shutter (without taking off shutter from the frame) area n.exc 1.5 sqm each and removal complete all as specified & directed.

Taking down Chowkhats or frame with shutter (without taking off shutter from the frame) area exc 1.50 sqm but n.exc 4 sqm each and removal complete all as specified & directed.

Taking down shutters of any description, of area not exc 1.0 sqm each complete all as specified and directed.

Taking down shutters of any description, of area exc 1.0 sqm but not exc 2.0 sqm each complete all as specified and directed.

Supply & fix factory made solid PVC door frame of size 50mmx47mm made out of 5mm single side prelam PVC sheet reinforced with MS square tube and edges painted to match with printed sheet complete all as specified & directed.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, at site complete all as specified & directed.

M&L for IInd class (Indian Sal, Bijasal, Hollock or Benteak) hardwood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified & directed.

M&L for second class (Indian Sal, Bijasal, Hollock or Benteak) hard wood in scantlings, clean sawn in unframed work complete all as specified & directed.

Supplying and fixing 35 mm thick flush shutters of make as approved by GE, solid core construction, with block board core and plywood face panels, both face covered with decorative face veneers with lipping/frame to match complete all as specified & directed.

S&F 35mm thick factory made second class hard wood glazed and skelton door shutter open rebated and prepared to receive glass or gauge etc divided into square with plain chamfered or rounded, mitred and rebated sash bars any number complete all as specified and as directed. Note :- Size of member of shutters as specified in SSR Part-I (2009) section 8 clause 8.20 (a).

Supplying and fixing 35 mm thick second class hardwood moulded flush shutters of make as approved by GE, with prepressed lamination on both side , solid core construction complete all as specified & directed. Note :- Size of member of shutters shall be as specified in SSR Part-I (2009) section 8 clause 8.20 (b).

Supplying and fixing 35 mm thick second class hardwood moulded gauged/glazed door of make as approved by GE, with prepressed lamination on both side , solid core construction complete all as specified & directed. Note :- Size of member of shutters shall be as specified in SSR Part-I (2009) section 8 clause 8.20 (b).

M&L for factory made 35mm thick second class (Indian Sal, Bijasal, Hollock or Benteak) hardwood plain, framed, panelled shutter (two or three panels) with lock rail and panel of 9mm thick B.W.P commercial ply or 12mm thick veneered particle board with commercial veneering on both faces; size of rail and stiles as per IS: 1003 (Part-I), kiln seasoned complete all as specified & directed.

M&L for 1 mm thick decorative laminated sheet type-I of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instruction including fixing of sheet on curved or flat surface complete all as specified & directed.

M&L for 12mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination as in timber frame work, rebated or flat edged; fixed with & including suitable size clamps, glue & screws etc as required at site complete all as specified & directed.

Supply only stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or any other means as per site requirement complete all as specified & directed. Note:- To be fixed in steel windows/ ventilators since fixing element of this item has already been considered alongwith steel windows/ ventilators as taken here-in-before.

Supplying & fixing continuous (Piano) hinges, mild steel, bright finish or electro galvanized, 30 mm width of flaps (when open) complete all as specified & directed.

S&F in repair 18 mm thick PVC sheet celuka board for kitchen cabinet including necessary fitting & fixture as per manufactures instructions complete all as specified & directed.

Supplying & fixing 250 mm long aluminium alloy, anodised sliding door bolts with hasp & staple (bolt type) & fixing clips of sheet, cast or extruded section and fixing bolts & sliding bolts of extruded section or cast aluminium alloy complete all as specified & directed.

Supply & fix 100mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

Supply & fix 75mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

Supplying & fixing 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified & directed.

Supplying & fixing 200mm long aluminium anodised barrel tower bolts of extruded section complete all as specified & directed.

Supplying & fixing 300 mm size ordinary rat tail rod pattern springs of mild steel including roller and roller plate complete all as specified & directed.

S&F stainless steel handle suitable for aluminium powder coated door shutter not less than 300 mm long including all connection fitting complete all as specified & directed.

Supply and fix aluminium handles 100 mm size, cast type, anodised complete all as specified & directed.

Supply and fix 150 mm size brass handles, cast type, polished bright anodised complete all as specified & directed.

Supply and fix 100 mm size brass handles, cast type, polished bright anodised complete all as specified & directed.

Supply and fix mortice lock ,vertical type size 100 mm 4 lever complete all as specified & directed.

Supplying & fixing floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor; overall length of cover plate 150mm complete all as specified & directed.

Supplying & fixing in repairs, 25 mm stainless steel, chromium plated curtain rod fancy type with brackets of brass fancy type fixed on walls with brass screws and curtain ring complete all as specified & directed. Note:- Cost of any number of brackets shall be deemed to be included in the quoted unit rate and nothing extra shall be paid on this account.

Supplying & fixing in repairs, stainless steel nobs and bracket complete all as specified & directed.

S&F double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

Supply and fix 40mm dia, brass cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified & directed.

S&F Door closer hydraulically regulated, designation No. 2, universal type of aluminium body fixed to door frame with screws or by welding suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and directed.

S&F in repair frame work for railing fixed to wall/floor made with 50/40/30 mm of stainless steel pipe (202) including necessary cutting and welding as per drawing complete all as specified & directed.

M&L for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 etc complete all as specified & directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering and ridge complete all as specified and as directed.

Supply and fix pre-painted galvalume aluminium zinc coating GI based 0.50mm thick (AZ-150) corrugated steel sheet of any colour having minimum tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws/ L or J type or cranked hook/ bolts complete all as specified & directed.

S&F of pre-painted galvalume aluminium zinc coating GI based 0.50 mm thick (AZ-150) plain steel sheet of any colour having tensile strength of 550 Mpa as in ridges, hips, valley gutters, drip and straight flashings (length & girth as fixed) fixed with self tapping screws complete all as specified & directed.

S&F 12 mm thick frosted glass fitted to wall (aluminium frame) as partition of toilets with necessary arrangements complete all as specified and as directed.

S&F 12 mm thick toughened glass plain or design pattern fitted to door/window/as partition with necessary accessories complete all as specified and as directed.

S&F 3 mm thick coloured polycarbonate sheet as in roof covering and fixing on stainless steel truss/tubular truss with sufficient and compactible washer and bolts including bending if required complete all as specified and as directed.

M&L for mild steel conforming to Fe.290.Gde-E-165 in framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; ladders; railings and similar work complete all as specified & directed.

M&L for running welding in repair nexc 6 mm thick metal complete all as specified & directed. Note :- The rates include for cleaning and preparing the surfaces to be welded together, holding the members in true position while welding and bevelling of edges, as required, in the case of metal exc 3mm thick.

M&L for mild steel TMT bars 10mm dia and over as in reinforcement for concrete, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 8mm dia as in reinforcement for concrete, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for mild steel TMT bars 8 to 10mm dia as in stirrups, spacers and binders for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F expanded metal not exceeding 4 Kg per Sqm in weight, cut to length, bent to shape required and tying with & including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples to brick wall/ stone block or slab wall complete all as specified & directed.

M&L for mild steel work of sections conforming to Fe-290.Gde-E-165 as in doors or gates of angle or other section with gusset plates, rails, braces, etc, drilled for fixing of steel sheeting or other covering; doors etc to be prepared for hanging or sliding with and including either hooks & hinges or steel hanging door fittings inclusive of steel sheeting, running rails & guides and hanging, fastening & fixing complete all as specified & directed.

M&L for anodized aluminium powder coated frame for door, window, ventilators with one or more rebates including cleats for fixing etc, (minimum thickness of powder coating is 50 micron) complete all as specified and directed.

S & F Aluminium powder coated (minimum thickness of powder coating 50 micron) door with frame top and sides of size 83.50x44.45x1.62mm ( Section No 19549), and shutter top rail and stile of size 92x38x1.70 mm ( Section No 21339) and Lock and bottom rail of size 125x37x1.80 mm ( Section No 19634) including rubber gasket, beading, anodised aluminium snap beading, screws, anodised aluminium fittings such as butt hinges/Pivot hinges 100 mm long (3 Nos.), handle (2 no.), Lock 06 Lever and locking arrangement ,fixing 5.00 mm thick glass with necessary rubber beading gasket etc including necessary plaster, painting ,cill and making good to disturbed portion all as specified and directed.

S & F Aluminium powder coated (minimum thickness of powder coating 50 micron) partition wall of size 83.50x44.45x1.62mm ( Section No 19549) including rubber gasket, beading, anodised aluminium snap beading, screws, anodised aluminium fittings ,fixing 5.00 mm thick glass or ACP sheet with necessary rubber beading gasket etc including necessary plaster, painting ,cill and making good to disturbed portion all as specified and directed.

M&L for anodized aluminium powder coated (minimum thickness of powder coating 50 micron) three track sliding window, frame side top and sides of size 92x31.75x1.5 mm (Section No. 20831), bottom size 92x31.75x1.5 mm (Section No. 20832) and shutter top and bottom size 40x18x1.55 mm (Section No. 20736) and sides (handle) of size 40x18x1.55 mm (Section No. 20738) and lock side shutter frame of size 40x18x1.55 mm (Section No. 20737) including rubber gasket, beading and locking arrangement including making good the disturbed portion complete including stainless steel wire staples and including fixing 5 mm thick glass with necessary rubber beading gasket etc including necessary plaster, painting, cill and making good to disturbed portion complete all as specified and directed. ( Note : Glazing is deemed to be included in the quoted rate of contractor and will not be paid for separately. )

M&L for anodized aluminium powder coated(minimum thickness of powder coating 50 micron) ventilator louvers type, frame top and bottom of size 31x42x1.6 mm (Section No. 20558), rectangular tube of size 40x20x2 mm (Section No. 14019) and middle vertical of size 42x46.20x1.6 mm ( Section No. 20560) and clip for fixing in wiremesh and glass of size 19x17.30x0.90 mm (Section No. 19360) including rubber gasket, beading and locking arrangement including making good the disturbed portion complete including stainless steel wire staples and including fixing 5 mm thick glass with necessary rubber beading gasket etc including necessary plaster, painting, cill and making good to disturbed portion complete all as specified and directed. ( Note : Glazing is deemed to be included in the quoted rate of contractor and will not be paid for separately. )

Taking down aluminium door shutter including floor door closer, removing glass with beading before taking down and refixing of glass, beading and floor door closer after replacing of broken parts of aluminium shutter including easing of shutter complete all as specified and directed. Note :- Broken parts of shutter will be measured and paid for separately

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) including removal of debris to out side MD land complete all as specified & directed.

M&L for glazed ceramic coloured tiles 300x200x7mm thick as approved by GE on vertical surfaces such as skirting/ dado, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over and including 10mm thick rendering in CM (1:4) complete all as specified & directed.

M&L for glazed ceramic coloured tiles 300x600x7mm thick as approved by GE on vertical surfaces such as skirting/ dado, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over and including 10mm thick rendering in CM (1:4) complete all as specified & directed.

M&L for glass mosaic tile including glass adhesive as in vertical surface as skirting/ dado, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over and including 10mm thick rendering in CM (1:3) complete all as specified & directed.

M&L for non-skid coloured ceramic tiles 7-8mm thick (square/ rectangular) area of each tile exc 0.11Sqm but not exc 0.18Sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over and including 15 mm thick screed bed in CM (1:6) complete all as specified & directed.

M&L for non-skid coloured ceramic tiles 7-8mm thick (square/ rectangular) area of each tile exc 0.18 Sqm but not exc 0.38Sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over and including 15 mm thick screed bed in CM (1:6) complete all as specified & directed.

M&L for Endura outdoor tiles 300x300x10 mm thick as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over and including 15 mm thick screed bed in CM (1:6) complete all as specified & directed.

M&L for rubber mould factory made coloured cement concrete chequered tiles with grey cement and pigments 300 mm x 300 mm x22-25mm thick, set, jointed and pointed in neat cement slurry in floors over and including 20mm thick screed bed in CM 1:6 complete all as specified & directed.

M&L for 18-20mm thick granite of approved quality as in platform i.e. in horizontal & vertical position, machine cut (table rubbed and polished) laid over and including 15mm thick rendering in CM 1:4 and jointed with grey cement slurry and pointed with white cement (1:2) using marble dust with admixture of pigment to match with the shade of granite stone including cutting and polishing complete all as specified and directed.

M&L for machine cut kota stone slab as in flooring, 18-20mm thick over & including 20mm thick cement screed bed in CM (1:6) laid and jointed with grey cement slurry mixed with pigment to match with the shade of the slab including rubbing and mirror polishing complete all as specified & directed.

M&L for machine cut kota stone slab as in skirting/ vertical surface, 18-20mm thick over & including 10mm thick rendering in CM (1:4) laid and jointed with gray cement slurry mixed with pigment to match with the shade of the slab including rubbing and mirror polishing complete all as specified & directed.

M&L for rounding to edges of granite stone slabs one edge, such as in counter type WHB, cooking platform and other similar situations etc. complete all as specified and directed.

M&L for 60mm thick rubber mould reflective factory made coloured pre cast PCC interlocking paver blocks/ tiles conforming to IS 15658-2006, M-35 designation of concrete and section as approved by GE in hard standing, laid dry over & including 50mm thick sand cushion and filling the voids of paver blocks/tiles with dry sand complete all as specified & directed.

M&L for 25 mm thick, PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in sub base of floors and the like etc considering the floor slope complete all as specified and directed.

M&L for 40 mm thick, PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in sub base of floors and the like etc considering the floor slope complete all as specified and directed. (Note:- Glass dividing strips shall be measured and paid for separately as " supply only".)

M&L for 75 mm thick, PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate as in sub base of floors and the like etc considering the floor slope complete all as specified and directed. (Note:- Glass dividing strips shall be measured and paid for separately as " supply only".)

Supply only Glass dividing strips, 38x3 mm thick complete all as specified & directed.

Taking down cement plaster etc on brick walls/ terrazo surfaces of any descriptions including racking out joints, hacking for keys, scrubbing down with water and disposal of unserviceable materials to out side of MD land complete all as specified & directed.

M&L for 10mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified & directed.

M&L for 15mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified & directed. ( Note:- WPC shall be measured and paid for separately as "Supply only". )

M&L for 5 mm thick rendering in cement mortar 1:3 on concrete surfaces as in ceiling finished even and smooth without using extra cement complete all specified and directed.

M&L for preparing new plastered or unplastered surfaces of ceiling and applying three coats of white wash as on ceiling complete all as specified and directed.

M&L for prepration of new plastered surfaces of external walls and applying two coats of cement base paint over & including a coat of white cement primer complete all as specified & directed.

M&L for prepration of old decorated plastered or unplastered surfaces of walls of any description and applying one coat of cement base paint on wall surface complete all as specified and directed.

M&L for prepration of old decorated plastered or unplastered surfaces of walls of any description by complete removal of existing treatment and preparation of surfaces for further treatment and applying two coats of oil bound distemper over 3 mm thick wall care putty on wall surface complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and apply two coats of oil emulsion distemper over 3 mm thick of Birla/ JK wall care putty over a coat of cement primer for smooth finish of wall complete all as specified and directed.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coat of synthetic enamel paint of colour as approved by GE over and including a coat of pink primer complete all as specified & directed.

M&L for preparation of old painted surface of wood and wooden based material of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for preparation of new surfaces of iron/ steel of any description over 10 cm width or girth and applying two coat of synthetic enamel paint of colour as approved by GE over and including a coat of red-oxide primer complete all as specified & directed.

M&L for preparation of old painted surfaces of steel of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed.

M&L for prepration of old decorated plastered or unplastered surfaces of walls of any description and applying one coats of plastic emulsion paint on wall surface complete all as specified and directed.

M&L for prepration of old decorated plastered or unplastered surfaces of walls of any description and applying two coats of pidilite product Dr. fixit rain coat on wall surface over a coat of primer seal complete all as specified and directed.

M&L for prepration of old decorated plastered or unplastered surfaces of walls exposed up to mother surface and filled all cracks of any description and applying three coats of pidilite product Dr. fixit heat shield on wall surface over a coat of primer seal complete all as specified and directed.

S&F in repair 15 mm bore brass chromium plated wall mixer, 3 in 1 system with hot and cold water arrangement with provision for both Hand Shower and Overhead Shower Complete with 115mm Long Bend Pipe, Connecting Legs & Wall Flange (without Hand & Overhead Shower) complete all as specified and as directed.

S&F in repair 15 mm bore brass chromium plated wall mixer, 3 in 1 system with hot and cold water arrangement with provision for Overhead Shower with 115mm Long Bend Pipe On Upper Side, Connecting Legs & Wall Flanges screwed for fixing complete all as specified and as directed.

S&F in repairs, 15mm dia bib cock,cast copper alloy with crutch or butterfly handle, fancy type, chromium plated, screwed down for iron pipe or brass ferrule complete all as specified & directed.

S&F in repairs, 15mm dia two way bib cock with wall flange ,cast copper alloy with crutch or butterfly handle, fancy type, chromium plated, screwed down for iron pipe or brass ferrule complete all as specified & directed.

Supply and fix in repairs, 15mm dia stop valves/cock, cast copper alloy, screwed down high pressure with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) screwed both ends for iron pipe or for unions complete all as specified & directed.

Supply and fix in repairs, 15mm dia stop valves/ angle cock, cast copper alloy, screwed down high pressure with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) screwed both ends for iron pipe or for unions complete all as specified & directed.

S&F in repair towel ring complete all as specified and directed.

S&F in repair towel rack 600 mm long with lower hanger complete all as specified and directed.

S&F toilet paper holder of brass, chromium plated, fixed to walls with chromium plated (CP) brass screws complete all as specified and directed.

Supply and fix in repairs, pillar taps, cast copper alloy with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe 15mm dia complete complete all as specified & directed.

S&F in repair 15 mm bore brass chromium plated mixer for wash hand basin mixing of hot and cold water along with CP brass caps screwed for fixing complete all as specified and as directed.

Supply & fix in repair 20mm bore gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

Supply & fix in repair 15 mm bore gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

Supply & fix in repair Concussive push button type self closing taps of cast copper alloy chromium plated, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs 15mm bore PVC connection pipe 450mm long with PTMT nuts complete all as specified & directed.

S&F in repairs 15mm bore PVC connection pipe 600mm long with PTMT nuts complete all as specified & directed.

S&F in repair, CP shower rose 125 mm dia of size suitable for 15mm bore GI pipe with or without swivel joint including fixing to pipe and union as approved by GE complete all as specified and directed.

Supply and fix in repair 10 ltr capacity PVC valve less syphonic action type flushing cistern low level 'white' with inlet ball valve, float valve & handle Including 32mm bore PVC flush pipe & brackets and brackets fixed to wall complete all as specified & directed.

Supply and fix in repair 125/150 mm dia chromium plated floor trap, with grating including jointing to waste pipe fixed in cement mortar (1:4) complete all as specified and directed.

Supply and fix in repair 32 mm dia chromium plated bottle trap for wash hand basin with inlet & outlet screwed for pipes or connection including necessary packing union and cap complete all as specified and directed.

Supply & fix in repairs vitreous china squatting pan, Orissa pattern of size 580x440 mm white, with integral foot rest and PVC 'P' or 'S' trap including connection to trap, and to flush pipe, etc (excluding flushing pipe) and making good to floor complete all as specified & directed.

Supply & fix in repairs vitreous china wash down water closet pan (pedestal pattern) white (excluding fixing bolts, flushing cistern and flush pipe) but plastic water closet seat, black/ white, closed pattern with recessed bottom, and cover and mild steel chromium plated or aluminium hinging device, complete all as specified & directed.

S&F in repair plastic water closet seat cover, coloured, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed..

S&F in repair hand Shower (Health Faucet) with 8mm Dia,1.2 Meter Long Flexible Tube & Wall Hook suitable for EWC including nuts washer complete all as specified and directed.

Supply & fix in repairs vitreous china white WHB (550 x 400 mm) flat back with CP waste coupling, waste pipe, brackets including cutting for and pinning in ends of brackets complete all as specified and directed.

Supply & fix in repairs chromium plated single handle sink mixer cold water screwed down for iron pipes suitable for 15 mm bore pipe complete all as specified and directed.

Supply & fix in repair 15mm bore medium grade galvanised steel tubes with all fittings and fixed complete to walls and ceilings or laid in floor complete all as specified & directed.

Supply & fix in repair 20mm bore medium grade galvanised steel tubes with all fittings and fixed complete to walls and ceilings or laid in floor complete all as specified & directed.

Refixing old steel water tubing 15mm dia with and including new GI fittings and connected to new or old positions of walls, ceilings, floors etc complete all as specified and directed. Note: Old GI pipe obtained from taking up or down here-in-before shall be re-used after necessary cleaning.

Refixing old steel water tubing 20mm dia with and including new GI fittings and connected to new or old positions of walls, ceilings, floors etc complete all as specified and directed. Note: Old GI pipe obtained from taking up or down here-in-before shall be re-used after necessary cleaning.

Supply and fix in repair 110 mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints,fixed to wall or laid in trenches or in floor with & including necessary clamps of requird size etc complete all as specifed & directed.

Supply and fix in repair 75 mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floor with & including necessary clamps of requird size etc complete all as specifed & directed.

Supply and fix in repair 40 mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floor with & including necessary clamps of requird size etc complete all as specifed & directed.

Supply & fix in repairs, PVC (SWR) branch piece (single Y), equal or unequal, 110 mm bore with access door rubber ring joint fixed to wall complete all as specified & directed.

Supply & fix in repairs, PVC (SWR) branch piece (single Y), equal or unequal, 75 mm bore with access door rubber ring joint fixed to wall complete all as specified & directed.

Supply and fix 110 mm bore PVC (SWR) bends of any radius provided with access door complete all as specified & directed.

Supply and fix 75 mm bore PVC (SWR) bends of any radius provided with access door complete all as specified & directed.

Supply and fix 40 mm bore PVC (SWR) bends of any radius provided with access door complete all as specified & directed.

Supply & fix PVC (SWR) junction single (single T), equal or unequal provided with access door, 110mm bore complete all as specified & directed.

Supply & fix PVC (SWR) junction single (single T), equal or unequal provided with access door, 75 mm bore complete all as specified & directed.

Supply & fix PVC (SWR) junction single (double T), equal or unequal provided with access door, 110mm bore complete all as specified & directed.

Supply & fix PVC (SWR) junction single (double T), equal or unequal provided with access door, 40 mm bore complete all as specified & directed.

S&F in repair PVC (SWR) gully trap, out let dia 125/110mm, plain with grating including jointing with solvent complete all as specified and as directed.

S&F in repair PVC (SWR) multi floor trap, out let dia 75 mm, plain with grating including jointing with solvent complete all as specified and as directed.

S&F in repair PVC (SWR) floor trap, out let dia 75 mm, plain with grating including jointing with solvent complete all as specified and as directed.

Supply and fix 500 ltrs capacity rotational moulded polyethylene water storage tank tripple layered (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified & directed.

Supply and fix 1000 ltrs capacity rotational moulded polyethylene water storage tank tripple layered (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified & directed.

S&F in repairs, sheet glass corner shelf consisting of 5.5mm thick sheet glass shelf 30 cm wide complete all as specified & directed.

Supply & fix in repairs, soap dish disc wall mounted (oval) type including all necessary screws of same finish of pattern & make as approved by GE complete all as specified and directed.

S&F in repairs, chromium plated glass shelf 550 mm long complete all as specified & directed.

S&F, in repair, PVC Bath Cabinet made from hard thermosetting material with mirror, white/ivory colour, 400 x 500mm size. complete all as specified and directed.

S&F in repairs, double coat hook complete all as specified & directed.

M&L for Brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified & directed.

M&L for Solar control film 25 micron reflective type (gareware sun control or equivalent as approved by GE) complete all as specified & directed.

S&F in repairs, door rubber seal complete all as specified & directed.

S&F figured glass, pin head type 3.0mm thick and glazing with oil putty/ beads in squares n. exc 0.5sqm in each pane complete all as specified & directed. Notes:- (i) Glazing in old work, serviceable beads as obtained from hacking out of sheet glass shall be re-used after cleaning/ rubbing the the same with sand paper, if required as per site requirement. (ii) Glazing in new work, beads shall be supplied with joinery.

Supply and fix sheet glass, ordinary quality 5.5 mm thick and glazing with oil putty/ beads in squares n. exc 0.5sqm in each pane complete all as specified & directed. Notes:- (i) Glazing in new steel work/ joinery, rate of oil putty shall be deemed to be included in the unit quoted rate for this item. (ii) Glazing in new wood work/ joinery, beads shall be supplied with joinery.

Supply and fix sheet glass, ordinary quality 6.3 mm thick and glazing with oil putty/ beads in squares n. exc 0.5sqm in each pane complete all as specified & directed. Notes:- (i) Glazing in new steel work/ joinery, rate of oil putty shall be deemed to be included in the unit quoted rate for this item. (ii) Glazing in new wood work/ joinery, beads shall be supplied with joinery.

Supply and fix sheet glass, ordinary quality 10 mm thick and glazing with oil putty/ beads in squares n. exc 0.5sqm in each pane complete all as specified & directed. Notes:- (i) Glazing in new steel work/ joinery, rate of oil putty shall be deemed to be included in the unit quoted rate for this item. (ii) Glazing in new wood work/ joinery, beads shall be supplied with joinery.

S&F 5mm thick beveled edge best quality looking mirror with 30 mm PVC beading all around the glass, mounted over 6 mm thick AC bldg board, size of mirror as per site requirement and as directed by GE complete all as specified and directed.

Dismantling of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and pre-cast concrete articles complete all as specified and directed.

Dismantling timber scantling 40 Sqcm and over in section in any position as in framed work complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets complete all as specified and as directed..

S&F suspended false ceiling grid system using chicago metallic (E Grid) exposed suspended system, grid size 600 x 600 mm comprising of GI powder coated main runner 39 x 24 x 0.8 mm (Thickness comprising of GI/0.4mm + PPPCGS/0.3mm and min weight of runner 1.35 Kg for 3600mm length), cross tee 29 x 24 x 0.80mm (Thickness comprising of GI/0.4 mm + PPPCGS/0.3mm and min weight of angle 0.195 Kg for 600mm length) and wall angle 22.2 x 22.2 x 0.65 mm thick (Thickness comprising of GI/0.35mm + PPPCGS/0.3mm and min weight of angle 0.7 Kg for 3050mm length) with and including 4mm thick HPSC (High Pressure Steam Cured) pre-primed, self embosed, textured design board, water resistant, termite resistant, fire resistant for insulation and acoustic purpose to be placed in grid system duly suspended with @ 1.2m c/c both way with 4 mm dia GI wire hangar fixed with steel dash fasteners or from purlin of roof with butterfly clips (wt 0.007kg), hold down clips (wt 0.0035kg) etc complete, ( main runner / cross tee /wall angle of Galvanised Iron powder coated), as per manufacturere instruction complete all as specified and directed. Note : Cost of making frame work and board (cut out) for fixing light fitting grill diffuser etc shall be deemed included in the quoted rate.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete including removal of debris to out side MD land complete all as specified & directed.

Demolition of reinforced cement concrete jali of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete including removal of debris to out side MD land complete all as specified & directed.

Demolition of reinforced cement concrete Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work any description and in any position not otherwise specifically provided for reinforcement cut as required to facilitate demolition) complete including removal of debris to out side MD land complete all as specified & directed.

Dismantling of stone slab and tile of any description or thickness of floor , aprons etc laid, bedded and pointed in any mortar including removal of debrise to out side MD land complete all as specified & directed.

Demolition of cement concrete of any description (unreinforced) in ground floors and paving not exceeding 15 cms thickness (below or above ground level) including removal of debris to out side MD land complete all as specified & directed.

M&L for 10mm thick rendering over roof surfaces in CM 1:3 with using water proofing compound @ 3% by wt of cement or as per manufacturer's instructions, finished even and smooth without using extra cement complete all as specified & directed. Note: WPC shall be measured and paid separately as "Supply Only" under respective item of BOQ.

M&L for applying evenly tack coat of hot blown bitumen 85/25 grade conforming to IS-702 @ 1.20 kg/sqm after cleaning the surfaces over & including a coat of bitumen primer @ 0.30 litre/ sqm consisting of 3/4 part bitumen of grade 85/25 and 1/4 part of kerosene oil on the top of prepared roof surfaces complete all as specified & directed.

M&L for unrolled over the bitumen coated surface, 3mm thick spun bonded non-woven polyester reinforced APP modified water proofing membrane weighing not less than 3.0 Kg/Sqm with minimum over lap of 100mm and over lap shall be sealed by flame as per manufacturer's instructions complete all as specified & directed. Note:- Suitable embedment of APP modified water proofing membrane shall be ensured into walls/parapet walls, special care shall be taken in laying APP modified water proofing membrane in situations such as drain/ expansion joints etc.

M&L for applying a coat of bituminous aluminium paint @ 100gm/ sqm and blinding material such as dry sand @ 0.75Kg/ Sqm over & including a coat of hot air blown bitumen 85/25 grade conforming to IS-702 @ 1.20 kg/sqm over polymeric membrane complete all as specified & directed. Note- Bituminous aluminium paint shall be of same manufacturer's as specified for polymeric water proofing membrane.

Taking down/ removing existing roof treatment over roof slab, roughening surfaces of old concrete floor/ roof/ terrace by picking and wire brushing the surface to remove the loose concrete, dust etc sweeping clean and washing down with water to remove dust, etc including removal of debrise to a distance 50 m out side MD land complete all as specified & directed.

S&F stainless steel cover for drain around the pool area complete all as specified and directed.

Removing building materials etc. (other than spoil) to a distance of exc 1.5 Km but not exc 5 Km beyond the lead included in the rates, including loading, unloading and stacking at the destination complete all as specified and directed.

Supplying and fixing for FRP diving board (of size 4.8 m long and 0.51 m width and 1.5 inch to 2.5 inch thick from front end to resin compositely reinforced with CSM 450 chopped glass strand matt and moulded with anti slippery top laminated with WR 300 matt without roller and fulcrum rear end) made of burma teakwood laminated with 99.7% water resistant polyster including MS roller and fulcrum with hinge complete all as specified & directed. ( Note : The work shall be carried out by the Specialist Agency as approved by GE.)

S&F frame work for railing fixed to wall/floor made with 50 mm /40 mm / 30 mm/ 20 mm stainless steel pipe including cutting & necessary welding as per drawing complete all as specified & directed.

Providing one layer of guniting of thickness not exceeding 50 mm in CM 1:3 with steel reinforcement including MS chicken wire mesh of weight exceeding 0.25 kg/sqm and n.exc 4 kg/sqm if required by means of tinned tacks or welded to existing reinforcement for top & bottom of roof slab,beams, columns and staircases etc including scaffolding at any height as required and including removal of loose particle of concrete and reinforcement and applying rust protective coating complete all as specified & directed.

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete complete all as specified & directed.

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron. complete all as specified & directed.

Cleaning the wall surface with wire brush & water and applying a coat of super latex compound mixed in ratio of 1:4:7 (Super latex + water + cement) on brick concrete surfaces before applying rendering as recommended by manufacturer complete all as specified & directed.

M&L for preparation of new plastered or unplastered surface of wall and applying two coat of weather proof antifungal paint exterior emulsion Apex paint white or tinted over and including one coat of cement primer complete all as specified & directed.

M&L for preparation of old plastered or unplastered surface of wall and applying one coat of weather proof antifungal paint exterior emulsion Apex paint white or tinted complete all as specified & directed.

S&F Stack clamps for 100 mm bore of pipe out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

Taking down carefully copper/aluminium point wiring on batten/ PVC conduit (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, sockets, light fittings etc, including removal and making good disturbed surfaces of walls, ceilings etc as per existing complete all as specified & directed.

Taking down existing exhaust/ ceiling fan of any size/ sweep and depositing in the safe custody of MES store complete all as specified & directed.

Taking down main switches/ DB's (alongwith existing board, MCBs & isolators) including removing the same from site and making good disturbed surfaces complete all as specified & directed.

Taking down existing old/ unserviceable sub main wiring of any type and description, removal of teak wood batten/ PVC pipe/ PVC casing & caping and making good disturbed surfaces of walls, ceilings etc as per existing complete all as specified and directed.

M&L for point wiring concealed type with 1.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed multistranded copper copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated/ ebonite sheet cover for fixing switches/ socket/ regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish for the one light /fan/exhaust/bell point controlled by one no one way switch 5/6 Amps complete all as specified & directed.

M&L for point wiring concealed type with 1.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated/ ebonite sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish for the one socket out let 3/5 pin, 5/6 Amps controlled by one no one way piano type switch on the same board with other switches complete all as specified & directed.

M&L for point wiring concealed type with 1.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated/ ebonite sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish for the one socket out let 3/5 pin, 5/6 Amps controlled by one no one way piano type switch on independent board but not below the switch board of light points in same vertical plane complete all as specified & directed.

M&L for point wiring concealed type with 2.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated/ ebonite sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish for the one socket out let 3/6 pin, 15/16 Amps controlled by one no one way piano type switch on independent board complete all as specified & directed.

Supply & fix in replacement of white modular cover plate with frame for modular switch 1 module as per existing make/model complete all as specified & directed.

Supply & fix in replacement of white modular cover plate with frame for modular switch 2 module as per existing make/model complete all as specified & directed.

Supply & fix in replacement of white modular cover plate with frame for modular switch 3 module as per existing make/model complete all as specified & directed.

Supply & fix in replacement of white modular cover plate with frame for modular switch 4 module as per existing make/model complete all as specified & directed.

Supply & fix in replacement of white modular cover plate with frame for modular switch 6 module as per existing make/model complete all as specified & directed.

Supply & fix in replacement of white modular cover plate with frame for modular switch 8 module as per existing make/model complete all as specified & directed.

Supply & fix in replacement modular metal flush box 1/2 module suitable for modular switch as existing switch box and making good the disturbed surface complete all as specified & directed.

Supply & fix in replacement modular metal flush box 3 module suitable for modular switch as existing switch box and and making good the disturbed surface complete all as specified & directed.

Supply & fix in replacement modular metal flush box 4/5 module suitable for modular switch as existing switch box and making good the disturbed surface complete all as specified & directed.

Supply & fix in replacement modular metal flush box 6/8 module suitable for modular switch as existing switch box and making good the disturbed surface complete all as specified & directed.

Supply & fix in replacement of modular switch 06-10 Amp one module 230 volts AC complete all as specified and directed.

Supply & fix in replacement of modular switch 16 Amp one module 230 volts AC complete all as specified and directed.

Supply & fix in replacement of modular socket 6 Amp, 2/3 pin combined 2 module, 230 volt AC complete all as specified and directed.

Supply & fix in replacement of modular socket 6/16 Amp, 2/3 pin combined 2 module, 230 volt AC complete all as specified and directed.

Supply and fix angle type lamp holder insulated with polycarbonate body complete all as specified and directed.

Supply and fix in repairs, decorative wall light fixture made up of polycarbonate, suitable for 9 W retrofit LED lamp B22 base and connecting up with & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed.

Supply & fix ceiling rose, surface bakelite, 65x50mm surface type, two to three terminals, AC 240 volts complete all as specified & directed.

Supply & fix in repairs, modular stepped type electronic fan regulator mini flush type 120/ 280 Volts, 02 module complete all as specified & directed.

M&L for provision of sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 4.0 sqmm drawn in and including rigid PVC conduit medium grade ISI marked not less than 25 mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 4sqmm as earth continuity and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish complete all as specified & directed. Notes:- (i) Finished sub main wiring with two runs of 4.0 sqmm cable & one run of 4 sqmm cable alongwith PVC conduit and its accessories shall be measured and paid one unit length. (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles. (iii) Colour coding for wiring/ bus bar/ main connection shall be followed .

M&L for provision of sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 6.0 sqmm drawn in and including rigid PVC conduit medium grade ISI marked not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 6 sqmm as earth continuity and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish complete all as specified & directed. Notes:- (i) Finished sub main wiring with two runs of 6.0 sqmm cable & one run of 6 sqmm cable alongwith PVC conduit and its accessories shall be measured and paid one unit length. (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles. (iii) Colour coding for wiring/ bus bar/ main connection shall be followed .

M&L for provision of sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 2.5 sqmm drawn in and including rigid PVC conduit medium grade ISI marked not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 2.5 sqmm as earth continuity and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish complete all as specified & directed. Notes:- (i) Finished sub main wiring with two runs of 2.5 sqmm cable & one run of 2.5 sqmm cable alongwith PVC conduit and its accessories shall be measured and paid one unit length. (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles. (iii) Colour coding for wiring/ bus bar/ main connection shall be followed .

S & F, in repair, Smart bright Batten Series, LED luminaire using LED 22 watt 110 LM/watt with diffuser which ensures uniform distribution and comfort batten series features latest LED and delivers consistent light output, stable color, start Extruded Aluminum housing, Energy efficient, Flicker free start Inbuilt driver unit Suitable for wall and ceiling mounting using brackets complete all as specified and as directed.

S & F, in repair,10 watt LED mirror light fitting of decorative ultra slim square profile LED lighting fixture with extruded polycarbonate environment friendly with energy efficient with and including electric connection to ceiling rose with three core copper conductor cable of suitable size & length complete all as specified & directed.

S&F MCCB tripple pole, 415 V ,with thermal megnetic release, adjustable type 100 Amp with breaking capacity 16 KA including taking down old unserviceable MCCB of any type and capacity complete all as specified and as directed.

S&F, in replacement, sheet metal enclosure distribution boards IP-54 and IK-09 , double door factory made Vertical TPN 4 way 3 phase 415 volts 4 way with 200 amps rating copper bus barand PVC insulated copper jumpers of suitable size from the MCCB to the out going circuits one incoming MCCB 100 amps and 12 modules circuits comprising of 3 phase 4 wire of suitable rating all as specified and directed.

Supply and fix in repairs, 45 watt new generation energy saving and environmental friendly long life LED security light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP opening separate driver compartment with IP66 protection and impact resistance of IK07 on bldg wall with and including pipe bracket made of G.I tubing 32/40 mm dia bore medium grade ISI marked 1.20m long bent to shape & providing clamps 2 Nos made out of 50 x 6 mm Flat iron/ MS clamps & 12mm dia bolts, nuts & washers etc including painting to all and connecting up with & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed.

Supply and fixing in repair sheet metal enclosure MCB DB double door (Acrylic) single pole and neutral, 240 volts, 8 way with 200 Amp, 10 KA breaking capacity rated bus bar with blanking plate wherever required and IP-43 degree protection, complete all as specified & directed.

Supply & fix MCB SPN, 40 Amps, 'C' series, 240 volts, 50Hz, 10kA complete all as specified & directed.

Supply & fix MCB SP, 40 Amps, 'C' series, 240 volts, 50Hz, 10kA complete all as specified & directed.

Supply & fix in replacement, single pole and neutral sheet metal enclosure (AC box) with a two pin & earth plug and socket with one no. MCB SP of capacity 20 Amps 240 volts complete all as specified & directed.

Supply & fix MCB TPN, 63 Amps, 'C' series, 415 volts, 50Hz, 10kA complete all as specified & directed.

Supply and fix in repair TPN DB, 4 way double door sheet metal enclosure IP 43 -IK 09 with metal door, 415 volts with copper bus bar of 200A suitable for fixing MCBs, Isolators etc complete all as specified and directed.

Supply and fix in repairs, 70 watt Energy saving, environmental friendly, long life, exclusive innovative die-cast aluminium IP66 flood light, suitable for highlighting architectural facade and general purpose lighting & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed.

Supply and fix in repairs, 100 watt Energy saving, environmental friendly, long life, exclusive innovative die-cast aluminium IP66 flood light, suitable for highlighting architectural facade and general purpose lighting & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed.

M&L for earthing complete with galvansided steel earth plate electrode 600x600x6.0mm thick directly burried in the ground (earth pit not less than 2.25M deep below ground level) with top edge of earth plate not less than 1.50M deep below normal ground level, connected to galvanised iron wire 4mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel, 15mm bore GI pipe medium grade including necessary fittings for protection of earthing wire, watering pipe 20mm bore GI medium grade, concrete chamber in PCC (1:4:8) type D-2 using 40 mm grade aggregate, coping shall be in PCC (1:3:6) type C-1 using 20 mm grade aggregate and internal surfaces of concrete chamber shall be given 12mm thick plaster in CM (1:4), funnel with wire gauge of 22 gauge (0.63 mm) 8 mesh per linear including 50mm thick cover of RCC (1:2:4) type B-1 using 20mm grade stone aggregate reinforced with 8mm MS deformed bar @ 75 mm C/C both ways, char coal dust and common salt all as shown in electrical plate No. 3 of SSR Part-I (2009) including all necessary excavation & earth work and removal of surplus soil to a distance n. exc 50M and providing connection points with MS/ GI bolts & washers as required and connection from earth test point to earth electrode with same GI earth wire alongwith protection pipe and testing on completion complete all as specified and directed. Note:- GI wire and protection pipe from earth electrode to test point max upto 7.50M shall be deemed to be included in the unit rates as quoted by the contractor.

Supply and fixing ceiling fans complete with three blades 1.05 mm thick aluminium sheet, down rods, electronic regulator with remote control radio frequency 5 speed + off timer option and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply and fixing Single phase propeller type ventilating ( Exhaust fan) AC 230 volts 250 mm sweep, speed range 1200 rpm made of sturdy Engineering plastic body with insect protection, motion sensor and motorized louvre and full copper motor provides high speed and silent operation complete including making holes of suitable size and making good the disturbed surface and shutters including electric connection with PVC flexible twin core copper wire from ceiling rose to Exhaust fan, nut & bolt complete all as specified and as directed. Note:- Old fan to be deposited in MES store of AGE E/M

Supply and fixing Single phase wall mounted remote controlled fan heavy duty AC 230 volts 400 mm sweep , metallic body including electric connection with PVC flexible twin core copper wire for wall mounted fan, nut & bolt complete all as specified and as directed. Note:- Old fan to be deposited in MES store of AGE E/M

Taking down carefully any type of cable complete all as specified and directed.

Supply and laying or fixing or passing in trenches/ on pole/ through pipes, 1100 volts grade XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured, heavy duty electric cable with stranded aluminium conductor of cross section area 35 sqmm, 3.5 core including jointing materials such as cable glands & lugs etc and testing on completion complete all as directed.

Supply and laying or fixing or passing in trenches/ on pole/ through pipes, 1100 volts grade XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured, heavy duty electric cable with stranded aluminium conductor of cross section area 10 sqmm, 4 core including jointing materials such as cable glands & lugs etc and testing on completion complete all as directed.

Supply and spreading clean and dry fine sand free from sharp materials (unwashed) laying in trenches around the cable for cushioning in trenches, laid to a uniform thickness of 23cm (15cm under the cable & 8cm over the cable) and gently punned down to 18cm thickness complete all as specified and as directed. (Note :- Punned thickness will be measured.)

Supplying and fixing/ laying of 40mm bore dia GI pipe medium grade in trenches/ under roads/ along pole/ wall including all necessary fittings & clamps made out of 25x3mm flat iron as required for cable protection etc after taking out existing old unserviceable GI pipe with fittings complete all as specified and directed.

Supplying and laying brick covering with width equal to length of brick as mechanical protection to cable with well burnt sub class B brick laid dry flat complete all as specified and directed.

Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for laying of pipe, cable etc or n. exc.10 Sqm on plan and n. exc. 1.5m in depth and getting out in soft/ loose soil complete all as specified and directed.

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed.

Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Drilling (Horizontally) to existing road (maximum 10M wide) suitable for passing GI tubing of dia upto 80mm as required at site complete all as specified and directed. Note:- All necessary T&P required at site for drilling shall be arranged by contractor at his own cost and quoted rate shall be deemed to be included for all these provisions and nothing extra shall be paid on this account.

Schedule of credit amount of Rs. 1,77,510.00 to be deducted during AOC

S R BUILDERS AND SUPPLIERS

J.P ENTERPRISES

Kirti Chandeliya and Assosicates

DEEPAK CONSTRUCTION

Tiki Water proofing Co

M/S Modern builders