Construction Combined House for Srilankan Tamil Refugees Camp Phase III 2025-26 Combined House Unit No. 1 to 23 (23 units with 4 houses per Unit ) at M.Mettupatty Panchayat Erumapatty Block of Namakkal District Pkg.No1/2025

Amount

Construction New Combined house (4-Nos) at Srilankan Tamil Refugees Camp in Mettupatty H/O Mettupatty (Unit-1)

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,-

Cement concrete 1:4:8 (one of cement five of sand and ten of aggregate) using 40mm size hard broken granite stone jelly for flooring including well rammed and rendering the top surface rough to receive the floor finish, curing etc. complete complying with standard specifications. The rate is inclusive of necessary planking for panelling into bays wherever necessary and as directed by the departmental officers.

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Below Basement

Basement to Lintel

Litel to Roof

Supplying and erecting, centering for sides and soffits including necessary supports and strutting up to 3.30m height for the following surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size.90cm.x 60cm and 10 B.G stiffened with mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak (country wood) joists of size 10cm x 6.5cm. spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centres complete complying with standard specification (The payment for centering shall be given after the concrete is laid.) The retrieved materials should be taken back by the contractor.

upto Basement

Lintel and Sunshade

Roof Slab

Reinforcement Cement Concrete 1:1.5:3 using 20 mm ISS HBG metal for all RCC item of works excluding cost of reinforcement and fabricating charges, centering and shuttering but icluding curing and providing fixtures like fan clamps in the RCC floor or roof vibrators, finishing, curing etc. complete and also fixing fixtures like fan clamps in the RCC floor / roof slab wherever necessary and the bearing surfaces of walls, beams shall be plastered with cement mortar 1:3 (one cement and three sand) and kraft paper laid etc.complete complying with standard specifications and as directed by the departmental officers.

upto Basement

Lintel and Sunshade

Roof Slab

Supplying, fabricating and placing in position of mild steel or ribbed tor steel grills for all RCC works as per the design given including cost of steel and binding wire in all floors etc.complete complying with standard specifications. The contractor ha

Plastering the surface of walls with cement mortar 1:5 (one of cement and six of sand) 12mm thick in all floors Finishing smooth, scaffolding, curing etc., complete complying with standard specification as directed by the departmental officers.

Supply and applying of two coats of putty of 3mm tk over the exposed RCC surface thorougly cleaned out of dust and scrubbing as per specifications etc complete.,

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing 25 mm thickness of Granolithic pattern for floor finish with cement concrete 1:2:4 (One of Cement, two of sand and four of hard broken stone jelly) using 10 to 12 mm HBG stone jelly on top surface shall be rubbed smooth finishing and curing etc., complete as per the instruction of departmental officer.

Supply and Delivery Fabrication of MS doors with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete. (Refer TWAD Page No 94)

Steel Door (0.90x2.10m) (Refer TWAD Page No 94, WD-M1485)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supply and Delivery Fabrication of MS windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete.

Steel Windows 0.90mX1.20m (Refer TWAD Page No 94, WD-M1487)

Steel Windows 0.90mX0.60m (Refer TWAD Page No 94, WD-M1488)

Painting the newly plastered wall surfaces with two coats of white washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Painting the newly plastered wall surfaces with two coats of colour washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Supplying and painting two coats new iron work such as steel doors ventilators, window bars etc., (WITHOUT PRIMER)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Labour charges for fixing of doors including all charges etc. ( Refer SOR Page No-35, W-0152 )

Labour charges for fixing of Windows including all charges etc. ( Refer SOR Page No-35, W-0153 )

Provision for Cudappa Slab for Shelf 0.90 x 0.30 x 0.025 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Provision for Cudappa Slab for Shelf 1.77 x 0.60 x 0.040 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Providing rain water harvesting structure including earthwork excavation and filling with brick jally , 40mm jally and sand including cost of material and all labour charges.

Towards supply and delivery of RCC Jolly (20 cm x 20 cm) including cost and conveyance of materails and all labour charges for fixing in position as per std. Specification

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supply and fixing of 110 mm dia pvc pipe for chamber connection

Provision for Septic Tank (2-Nos)

Earthwork excavation in all soils & subsoils includibng all charges etc.,

Earth work excavation for foundation in hard rock requiring blasting & Stacking

Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier etc

Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all R.C.C works with standard specification etc complete.

Reinforced cement concrete 1:1.5:3mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum

Plastering with cement mortar 1:4 mix to 20 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Plastering with cement mortar 1:5 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Provision for electrification

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3 mm thick Hylum sheet cover with TW box And 5 A FT switch with continuous earth connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed Light point / fan point (For electronic Regulator) SD 24

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 mm X 100 mm X 113 mm TW switch box with 3 mm thick Hylum sheet cover for 5 A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for concealed PVC plug point SD 37

Supply and run of 2 of 1.50 sq.mm (22/0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade on 7/20GI bearer wire for service connection mains SD 64

Supply and run of 2 X 4 sq.mm (56 / 0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade in 25 mm dia GI pipe ( Class ' B ' ) suitably bent at both ends with necessary angle iron upright and end supports for mains. SD 70

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1"x1/8"copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW reepersof1" thick an either side with painting with suitable bolt and nuts for fixing theTWplank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Lower End) with suitable necessary connectio SD125

Supply and fixing of 1200 mm ( 48") AC ceiling fan complete with stepped electronic 300 W regulator with 300 mm down rod on the existing clamp. SD 112

Supply and fixing for 9W LED BULB SD 79

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Lower End (SD 506)

Supply and fixing for Arial Fuse Unit SD 130

Construction New Combined house (4-Nos) at Srilankan Tamil Refugees Camp in Mettupatty H/O Mettupatty (Unit-2)

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,-

Cement concrete 1:4:8 (one of cement five of sand and ten of aggregate) using 40mm size hard broken granite stone jelly for flooring including well rammed and rendering the top surface rough to receive the floor finish, curing etc. complete complying with standard specifications. The rate is inclusive of necessary planking for panelling into bays wherever necessary and as directed by the departmental officers.

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Below Basement

Basement to Lintel

Litel to Roof

Supplying and erecting, centering for sides and soffits including necessary supports and strutting up to 3.30m height for the following surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size.90cm.x 60cm and 10 B.G stiffened with mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak (country wood) joists of size 10cm x 6.5cm. spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centres complete complying with standard specification (The payment for centering shall be given after the concrete is laid.) The retrieved materials should be taken back by the contractor.

upto Basement

Lintel and Sunshade

Roof Slab

Reinforcement Cement Concrete 1:1.5:3 using 20 mm ISS HBG metal for all RCC item of works excluding cost of reinforcement and fabricating charges, centering and shuttering but icluding curing and providing fixtures like fan clamps in the RCC floor or roof vibrators, finishing, curing etc. complete and also fixing fixtures like fan clamps in the RCC floor / roof slab wherever necessary and the bearing surfaces of walls, beams shall be plastered with cement mortar 1:3 (one cement and three sand) and kraft paper laid etc.complete complying with standard specifications and as directed by the departmental officers.

upto Basement

Lintel and Sunshade

Roof Slab

Supplying, fabricating and placing in position of mild steel or ribbed tor steel grills for all RCC works as per the design given including cost of steel and binding wire in all floors etc.complete complying with standard specifications. The contractor ha

Plastering the surface of walls with cement mortar 1:5 (one of cement and six of sand) 12mm thick in all floors Finishing smooth, scaffolding, curing etc., complete complying with standard specification as directed by the departmental officers.

Supply and applying of two coats of putty of 3mm tk over the exposed RCC surface thorougly cleaned out of dust and scrubbing as per specifications etc complete.,

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing 25 mm thickness of Granolithic pattern for floor finish with cement concrete 1:2:4 (One of Cement, two of sand and four of hard broken stone jelly) using 10 to 12 mm HBG stone jelly on top surface shall be rubbed smooth finishing and curing etc., complete as per the instruction of departmental officer.

Supply and Delivery Fabrication of MS doors with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete. (Refer TWAD Page No 94)

Steel Door (0.90x2.10m) (Refer TWAD Page No 94, WD-M1485)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supply and Delivery Fabrication of MS windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete.

Steel Windows 0.90mX1.20m (Refer TWAD Page No 94, WD-M1487)

Steel Windows 0.90mX0.60m (Refer TWAD Page No 94, WD-M1488)

Painting the newly plastered wall surfaces with two coats of white washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Painting the newly plastered wall surfaces with two coats of colour washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Supplying and painting two coats new iron work such as steel doors ventilators, window bars etc., (WITHOUT PRIMER)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Labour charges for fixing of doors including all charges etc. ( Refer SOR Page No-35, W-0152 )

Labour charges for fixing of Windows including all charges etc. ( Refer SOR Page No-35, W-0153 )

Provision for Cudappa Slab for Shelf 0.90 x 0.30 x 0.025 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Provision for Cudappa Slab for Shelf 1.77 x 0.60 x 0.040 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Providing rain water harvesting structure including earthwork excavation and filling with brick jally , 40mm jally and sand including cost of material and all labour charges.

Towards supply and delivery of RCC Jolly (20 cm x 20 cm) including cost and conveyance of materails and all labour charges for fixing in position as per std. Specification

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supply and fixing of 110 mm dia pvc pipe for chamber connection

Provision for Septic Tank (2-Nos)

Earthwork excavation in all soils & subsoils includibng all charges etc.,

Earth work excavation for foundation in hard rock requiring blasting & Stacking

Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier etc

Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all R.C.C works with standard specification etc complete.

Reinforced cement concrete 1:1.5:3mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum

Plastering with cement mortar 1:4 mix to 20 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Plastering with cement mortar 1:5 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Provision for electrification

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3 mm thick Hylum sheet cover with TW box And 5 A FT switch with continuous earth connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed Light point / fan point (For electronic Regulator) SD 24

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 mm X 100 mm X 113 mm TW switch box with 3 mm thick Hylum sheet cover for 5 A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for concealed PVC plug point SD 37

Supply and run of 2 of 1.50 sq.mm (22/0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade on 7/20GI bearer wire for service connection mains SD 64

Supply and run of 2 X 4 sq.mm (56 / 0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade in 25 mm dia GI pipe ( Class ' B ' ) suitably bent at both ends with necessary angle iron upright and end supports for mains. SD 70

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1"x1/8"copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW reepersof1" thick an either side with painting with suitable bolt and nuts for fixing theTWplank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Lower End) with suitable necessary connectio SD125

Supply and fixing of 1200 mm ( 48") AC ceiling fan complete with stepped electronic 300 W regulator with 300 mm down rod on the existing clamp. SD 112

Supply and fixing for 9W LED BULB SD 79

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Lower End (SD 506)

Supply and fixing for Arial Fuse Unit SD 130

Construction New Combined house (4-Nos) at Srilankan Tamil Refugees Camp in Mettupatty H/O Mettupatty (Unit-3)

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,-

Cement concrete 1:4:8 (one of cement five of sand and ten of aggregate) using 40mm size hard broken granite stone jelly for flooring including well rammed and rendering the top surface rough to receive the floor finish, curing etc. complete complying with standard specifications. The rate is inclusive of necessary planking for panelling into bays wherever necessary and as directed by the departmental officers.

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Below Basement

Basement to Lintel

Litel to Roof

Supplying and erecting, centering for sides and soffits including necessary supports and strutting up to 3.30m height for the following surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size.90cm.x 60cm and 10 B.G stiffened with mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak (country wood) joists of size 10cm x 6.5cm. spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centres complete complying with standard specification (The payment for centering shall be given after the concrete is laid.) The retrieved materials should be taken back by the contractor.

upto Basement

Lintel and Sunshade

Roof Slab

Reinforcement Cement Concrete 1:1.5:3 using 20 mm ISS HBG metal for all RCC item of works excluding cost of reinforcement and fabricating charges, centering and shuttering but icluding curing and providing fixtures like fan clamps in the RCC floor or roof vibrators, finishing, curing etc. complete and also fixing fixtures like fan clamps in the RCC floor / roof slab wherever necessary and the bearing surfaces of walls, beams shall be plastered with cement mortar 1:3 (one cement and three sand) and kraft paper laid etc.complete complying with standard specifications and as directed by the departmental officers.

upto Basement

Lintel and Sunshade

Roof Slab

Supplying, fabricating and placing in position of mild steel or ribbed tor steel grills for all RCC works as per the design given including cost of steel and binding wire in all floors etc.complete complying with standard specifications. The contractor ha

Plastering the surface of walls with cement mortar 1:5 (one of cement and six of sand) 12mm thick in all floors Finishing smooth, scaffolding, curing etc., complete complying with standard specification as directed by the departmental officers.

Supply and applying of two coats of putty of 3mm tk over the exposed RCC surface thorougly cleaned out of dust and scrubbing as per specifications etc complete.,

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing 25 mm thickness of Granolithic pattern for floor finish with cement concrete 1:2:4 (One of Cement, two of sand and four of hard broken stone jelly) using 10 to 12 mm HBG stone jelly on top surface shall be rubbed smooth finishing and curing etc., complete as per the instruction of departmental officer.

Supply and Delivery Fabrication of MS doors with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete. (Refer TWAD Page No 94)

Steel Door (0.90x2.10m) (Refer TWAD Page No 94, WD-M1485)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supply and Delivery Fabrication of MS windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete.

Steel Windows 0.90mX1.20m (Refer TWAD Page No 94, WD-M1487)

Steel Windows 0.90mX0.60m (Refer TWAD Page No 94, WD-M1488)

Painting the newly plastered wall surfaces with two coats of white washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Painting the newly plastered wall surfaces with two coats of colour washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Supplying and painting two coats new iron work such as steel doors ventilators, window bars etc., (WITHOUT PRIMER)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Labour charges for fixing of doors including all charges etc. ( Refer SOR Page No-35, W-0152 )

Labour charges for fixing of Windows including all charges etc. ( Refer SOR Page No-35, W-0153 )

Provision for Cudappa Slab for Shelf 0.90 x 0.30 x 0.025 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Provision for Cudappa Slab for Shelf 1.77 x 0.60 x 0.040 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Providing rain water harvesting structure including earthwork excavation and filling with brick jally , 40mm jally and sand including cost of material and all labour charges.

Towards supply and delivery of RCC Jolly (20 cm x 20 cm) including cost and conveyance of materails and all labour charges for fixing in position as per std. Specification

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supply and fixing of 110 mm dia pvc pipe for chamber connection

Provision for Septic Tank (2-Nos)

Earthwork excavation in all soils & subsoils includibng all charges etc.,

Earth work excavation for foundation in hard rock requiring blasting & Stacking

Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier etc

Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all R.C.C works with standard specification etc complete.

Reinforced cement concrete 1:1.5:3mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum

Plastering with cement mortar 1:4 mix to 20 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Plastering with cement mortar 1:5 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Provision for electrification

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3 mm thick Hylum sheet cover with TW box And 5 A FT switch with continuous earth connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed Light point / fan point (For electronic Regulator) SD 24

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 mm X 100 mm X 113 mm TW switch box with 3 mm thick Hylum sheet cover for 5 A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for concealed PVC plug point SD 37

Supply and run of 2 of 1.50 sq.mm (22/0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade on 7/20GI bearer wire for service connection mains SD 64

Supply and run of 2 X 4 sq.mm (56 / 0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade in 25 mm dia GI pipe ( Class ' B ' ) suitably bent at both ends with necessary angle iron upright and end supports for mains. SD 70

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1"x1/8"copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW reepersof1" thick an either side with painting with suitable bolt and nuts for fixing theTWplank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Lower End) with suitable necessary connectio SD125

Supply and fixing of 1200 mm ( 48") AC ceiling fan complete with stepped electronic 300 W regulator with 300 mm down rod on the existing clamp. SD 112

Supply and fixing for 9W LED BULB SD 79

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Lower End (SD 506)

Supply and fixing for Arial Fuse Unit SD 130

Construction New Combined house (4-Nos) at Srilankan Tamil Refugees Camp in Mettupatty H/O Mettupatty (Unit-4)

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,-

Cement concrete 1:4:8 (one of cement five of sand and ten of aggregate) using 40mm size hard broken granite stone jelly for flooring including well rammed and rendering the top surface rough to receive the floor finish, curing etc. complete complying with standard specifications. The rate is inclusive of necessary planking for panelling into bays wherever necessary and as directed by the departmental officers.

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Below Basement

Basement to Lintel

Litel to Roof

Supplying and erecting, centering for sides and soffits including necessary supports and strutting up to 3.30m height for the following surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size.90cm.x 60cm and 10 B.G stiffened with mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak (country wood) joists of size 10cm x 6.5cm. spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centres complete complying with standard specification (The payment for centering shall be given after the concrete is laid.) The retrieved materials should be taken back by the contractor.

upto Basement

Lintel and Sunshade

Roof Slab

Reinforcement Cement Concrete 1:1.5:3 using 20 mm ISS HBG metal for all RCC item of works excluding cost of reinforcement and fabricating charges, centering and shuttering but icluding curing and providing fixtures like fan clamps in the RCC floor or roof vibrators, finishing, curing etc. complete and also fixing fixtures like fan clamps in the RCC floor / roof slab wherever necessary and the bearing surfaces of walls, beams shall be plastered with cement mortar 1:3 (one cement and three sand) and kraft paper laid etc.complete complying with standard specifications and as directed by the departmental officers.

upto Basement

Lintel and Sunshade

Roof Slab

Supplying, fabricating and placing in position of mild steel or ribbed tor steel grills for all RCC works as per the design given including cost of steel and binding wire in all floors etc.complete complying with standard specifications. The contractor ha

Plastering the surface of walls with cement mortar 1:5 (one of cement and six of sand) 12mm thick in all floors Finishing smooth, scaffolding, curing etc., complete complying with standard specification as directed by the departmental officers.

Supply and applying of two coats of putty of 3mm tk over the exposed RCC surface thorougly cleaned out of dust and scrubbing as per specifications etc complete.,

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing 25 mm thickness of Granolithic pattern for floor finish with cement concrete 1:2:4 (One of Cement, two of sand and four of hard broken stone jelly) using 10 to 12 mm HBG stone jelly on top surface shall be rubbed smooth finishing and curing etc., complete as per the instruction of departmental officer.

Supply and Delivery Fabrication of MS doors with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete. (Refer TWAD Page No 94)

Steel Door (0.90x2.10m) (Refer TWAD Page No 94, WD-M1485)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supply and Delivery Fabrication of MS windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete.

Steel Windows 0.90mX1.20m (Refer TWAD Page No 94, WD-M1487)

Steel Windows 0.90mX0.60m (Refer TWAD Page No 94, WD-M1488)

Painting the newly plastered wall surfaces with two coats of white washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Painting the newly plastered wall surfaces with two coats of colour washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Supplying and painting two coats new iron work such as steel doors ventilators, window bars etc., (WITHOUT PRIMER)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Labour charges for fixing of doors including all charges etc. ( Refer SOR Page No-35, W-0152 )

Labour charges for fixing of Windows including all charges etc. ( Refer SOR Page No-35, W-0153 )

Provision for Cudappa Slab for Shelf 0.90 x 0.30 x 0.025 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Provision for Cudappa Slab for Shelf 1.77 x 0.60 x 0.040 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Providing rain water harvesting structure including earthwork excavation and filling with brick jally , 40mm jally and sand including cost of material and all labour charges.

Towards supply and delivery of RCC Jolly (20 cm x 20 cm) including cost and conveyance of materails and all labour charges for fixing in position as per std. Specification

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supply and fixing of 110 mm dia pvc pipe for chamber connection

Provision for Septic Tank (2-Nos)

Earthwork excavation in all soils & subsoils includibng all charges etc.,

Earth work excavation for foundation in hard rock requiring blasting & Stacking

Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier etc

Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all R.C.C works with standard specification etc complete.

Reinforced cement concrete 1:1.5:3mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum

Plastering with cement mortar 1:4 mix to 20 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Plastering with cement mortar 1:5 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Provision for electrification

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3 mm thick Hylum sheet cover with TW box And 5 A FT switch with continuous earth connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed Light point / fan point (For electronic Regulator) SD 24

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 mm X 100 mm X 113 mm TW switch box with 3 mm thick Hylum sheet cover for 5 A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for concealed PVC plug point SD 37

Supply and run of 2 of 1.50 sq.mm (22/0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade on 7/20GI bearer wire for service connection mains SD 64

Supply and run of 2 X 4 sq.mm (56 / 0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade in 25 mm dia GI pipe ( Class ' B ' ) suitably bent at both ends with necessary angle iron upright and end supports for mains. SD 70

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1"x1/8"copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW reepersof1" thick an either side with painting with suitable bolt and nuts for fixing theTWplank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Lower End) with suitable necessary connectio SD125

Supply and fixing of 1200 mm ( 48") AC ceiling fan complete with stepped electronic 300 W regulator with 300 mm down rod on the existing clamp. SD 112

Supply and fixing for 9W LED BULB SD 79

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Lower End (SD 506)

Supply and fixing for Arial Fuse Unit SD 130

Construction New Combined house (4-Nos) at Srilankan Tamil Refugees Camp in Mettupatty H/O Mettupatty (Unit-5)

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,-

Cement concrete 1:4:8 (one of cement five of sand and ten of aggregate) using 40mm size hard broken granite stone jelly for flooring including well rammed and rendering the top surface rough to receive the floor finish, curing etc. complete complying with standard specifications. The rate is inclusive of necessary planking for panelling into bays wherever necessary and as directed by the departmental officers.

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Below Basement

Basement to Lintel

Litel to Roof

Supplying and erecting, centering for sides and soffits including necessary supports and strutting up to 3.30m height for the following surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size.90cm.x 60cm and 10 B.G stiffened with mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak (country wood) joists of size 10cm x 6.5cm. spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centres complete complying with standard specification (The payment for centering shall be given after the concrete is laid.) The retrieved materials should be taken back by the contractor.

upto Basement

Lintel and Sunshade

Roof Slab

Reinforcement Cement Concrete 1:1.5:3 using 20 mm ISS HBG metal for all RCC item of works excluding cost of reinforcement and fabricating charges, centering and shuttering but icluding curing and providing fixtures like fan clamps in the RCC floor or roof vibrators, finishing, curing etc. complete and also fixing fixtures like fan clamps in the RCC floor / roof slab wherever necessary and the bearing surfaces of walls, beams shall be plastered with cement mortar 1:3 (one cement and three sand) and kraft paper laid etc.complete complying with standard specifications and as directed by the departmental officers.

upto Basement

Lintel and Sunshade

Roof Slab

Supplying, fabricating and placing in position of mild steel or ribbed tor steel grills for all RCC works as per the design given including cost of steel and binding wire in all floors etc.complete complying with standard specifications. The contractor ha

Plastering the surface of walls with cement mortar 1:5 (one of cement and six of sand) 12mm thick in all floors Finishing smooth, scaffolding, curing etc., complete complying with standard specification as directed by the departmental officers.

Supply and applying of two coats of putty of 3mm tk over the exposed RCC surface thorougly cleaned out of dust and scrubbing as per specifications etc complete.,

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing 25 mm thickness of Granolithic pattern for floor finish with cement concrete 1:2:4 (One of Cement, two of sand and four of hard broken stone jelly) using 10 to 12 mm HBG stone jelly on top surface shall be rubbed smooth finishing and curing etc., complete as per the instruction of departmental officer.

Supply and Delivery Fabrication of MS doors with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete. (Refer TWAD Page No 94)

Steel Door (0.90x2.10m) (Refer TWAD Page No 94, WD-M1485)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supply and Delivery Fabrication of MS windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete.

Steel Windows 0.90mX1.20m (Refer TWAD Page No 94, WD-M1487)

Steel Windows 0.90mX0.60m (Refer TWAD Page No 94, WD-M1488)

Painting the newly plastered wall surfaces with two coats of white washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Painting the newly plastered wall surfaces with two coats of colour washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Supplying and painting two coats new iron work such as steel doors ventilators, window bars etc., (WITHOUT PRIMER)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Labour charges for fixing of doors including all charges etc. ( Refer SOR Page No-35, W-0152 )

Labour charges for fixing of Windows including all charges etc. ( Refer SOR Page No-35, W-0153 )

Provision for Cudappa Slab for Shelf 0.90 x 0.30 x 0.025 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Provision for Cudappa Slab for Shelf 1.77 x 0.60 x 0.040 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Providing rain water harvesting structure including earthwork excavation and filling with brick jally , 40mm jally and sand including cost of material and all labour charges.

Towards supply and delivery of RCC Jolly (20 cm x 20 cm) including cost and conveyance of materails and all labour charges for fixing in position as per std. Specification

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supply and fixing of 110 mm dia pvc pipe for chamber connection

Provision for Septic Tank (2-Nos)

Earthwork excavation in all soils & subsoils includibng all charges etc.,

Earth work excavation for foundation in hard rock requiring blasting & Stacking

Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier etc

Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all R.C.C works with standard specification etc complete.

Reinforced cement concrete 1:1.5:3mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum

Plastering with cement mortar 1:4 mix to 20 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Plastering with cement mortar 1:5 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Provision for electrification

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3 mm thick Hylum sheet cover with TW box And 5 A FT switch with continuous earth connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed Light point / fan point (For electronic Regulator) SD 24

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 mm X 100 mm X 113 mm TW switch box with 3 mm thick Hylum sheet cover for 5 A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for concealed PVC plug point SD 37

Supply and run of 2 of 1.50 sq.mm (22/0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade on 7/20GI bearer wire for service connection mains SD 64

Supply and run of 2 X 4 sq.mm (56 / 0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade in 25 mm dia GI pipe ( Class ' B ' ) suitably bent at both ends with necessary angle iron upright and end supports for mains. SD 70

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1"x1/8"copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW reepersof1" thick an either side with painting with suitable bolt and nuts for fixing theTWplank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Lower End) with suitable necessary connectio SD125

Supply and fixing of 1200 mm ( 48") AC ceiling fan complete with stepped electronic 300 W regulator with 300 mm down rod on the existing clamp. SD 112

Supply and fixing for 9W LED BULB SD 79

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Lower End (SD 506)

Supply and fixing for Arial Fuse Unit SD 130

Construction New Combined house (4-Nos) at Srilankan Tamil Refugees Camp in Mettupatty H/O Mettupatty (Unit-6)

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,-

Cement concrete 1:4:8 (one of cement five of sand and ten of aggregate) using 40mm size hard broken granite stone jelly for flooring including well rammed and rendering the top surface rough to receive the floor finish, curing etc. complete complying with standard specifications. The rate is inclusive of necessary planking for panelling into bays wherever necessary and as directed by the departmental officers.

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Below Basement

Basement to Lintel

Litel to Roof

Supplying and erecting, centering for sides and soffits including necessary supports and strutting up to 3.30m height for the following surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size.90cm.x 60cm and 10 B.G stiffened with mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak (country wood) joists of size 10cm x 6.5cm. spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centres complete complying with standard specification (The payment for centering shall be given after the concrete is laid.) The retrieved materials should be taken back by the contractor.

upto Basement

Lintel and Sunshade

Roof Slab

Reinforcement Cement Concrete 1:1.5:3 using 20 mm ISS HBG metal for all RCC item of works excluding cost of reinforcement and fabricating charges, centering and shuttering but icluding curing and providing fixtures like fan clamps in the RCC floor or roof vibrators, finishing, curing etc. complete and also fixing fixtures like fan clamps in the RCC floor / roof slab wherever necessary and the bearing surfaces of walls, beams shall be plastered with cement mortar 1:3 (one cement and three sand) and kraft paper laid etc.complete complying with standard specifications and as directed by the departmental officers.

upto Basement

Lintel and Sunshade

Roof Slab

Supplying, fabricating and placing in position of mild steel or ribbed tor steel grills for all RCC works as per the design given including cost of steel and binding wire in all floors etc.complete complying with standard specifications. The contractor ha

Plastering the surface of walls with cement mortar 1:5 (one of cement and six of sand) 12mm thick in all floors Finishing smooth, scaffolding, curing etc., complete complying with standard specification as directed by the departmental officers.

Supply and applying of two coats of putty of 3mm tk over the exposed RCC surface thorougly cleaned out of dust and scrubbing as per specifications etc complete.,

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing 25 mm thickness of Granolithic pattern for floor finish with cement concrete 1:2:4 (One of Cement, two of sand and four of hard broken stone jelly) using 10 to 12 mm HBG stone jelly on top surface shall be rubbed smooth finishing and curing etc., complete as per the instruction of departmental officer.

Supply and Delivery Fabrication of MS doors with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete. (Refer TWAD Page No 94)

Steel Door (0.90x2.10m) (Refer TWAD Page No 94, WD-M1485)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supply and Delivery Fabrication of MS windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete.

Steel Windows 0.90mX1.20m (Refer TWAD Page No 94, WD-M1487)

Steel Windows 0.90mX0.60m (Refer TWAD Page No 94, WD-M1488)

Painting the newly plastered wall surfaces with two coats of white washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Painting the newly plastered wall surfaces with two coats of colour washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Supplying and painting two coats new iron work such as steel doors ventilators, window bars etc., (WITHOUT PRIMER)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Labour charges for fixing of doors including all charges etc. ( Refer SOR Page No-35, W-0152 )

Labour charges for fixing of Windows including all charges etc. ( Refer SOR Page No-35, W-0153 )

Provision for Cudappa Slab for Shelf 0.90 x 0.30 x 0.025 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Provision for Cudappa Slab for Shelf 1.77 x 0.60 x 0.040 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Providing rain water harvesting structure including earthwork excavation and filling with brick jally , 40mm jally and sand including cost of material and all labour charges.

Towards supply and delivery of RCC Jolly (20 cm x 20 cm) including cost and conveyance of materails and all labour charges for fixing in position as per std. Specification

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supply and fixing of 110 mm dia pvc pipe for chamber connection

Provision for Septic Tank (2-Nos)

Earthwork excavation in all soils & subsoils includibng all charges etc.,

Earth work excavation for foundation in hard rock requiring blasting & Stacking

Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier etc

Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all R.C.C works with standard specification etc complete.

Reinforced cement concrete 1:1.5:3mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum

Plastering with cement mortar 1:4 mix to 20 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Plastering with cement mortar 1:5 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Provision for electrification

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3 mm thick Hylum sheet cover with TW box And 5 A FT switch with continuous earth connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed Light point / fan point (For electronic Regulator) SD 24

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 mm X 100 mm X 113 mm TW switch box with 3 mm thick Hylum sheet cover for 5 A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for concealed PVC plug point SD 37

Supply and run of 2 of 1.50 sq.mm (22/0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade on 7/20GI bearer wire for service connection mains SD 64

Supply and run of 2 X 4 sq.mm (56 / 0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade in 25 mm dia GI pipe ( Class ' B ' ) suitably bent at both ends with necessary angle iron upright and end supports for mains. SD 70

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1"x1/8"copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW reepersof1" thick an either side with painting with suitable bolt and nuts for fixing theTWplank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Lower End) with suitable necessary connectio SD125

Supply and fixing of 1200 mm ( 48") AC ceiling fan complete with stepped electronic 300 W regulator with 300 mm down rod on the existing clamp. SD 112

Supply and fixing for 9W LED BULB SD 79

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Lower End (SD 506)

Supply and fixing for Arial Fuse Unit SD 130

Construction New Combined house (4-Nos) at Srilankan Tamil Refugees Camp in Mettupatty H/O Mettupatty (Unit-7)

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,-

Cement concrete 1:4:8 (one of cement five of sand and ten of aggregate) using 40mm size hard broken granite stone jelly for flooring including well rammed and rendering the top surface rough to receive the floor finish, curing etc. complete complying with standard specifications. The rate is inclusive of necessary planking for panelling into bays wherever necessary and as directed by the departmental officers.

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Below Basement

Basement to Lintel

Litel to Roof

Supplying and erecting, centering for sides and soffits including necessary supports and strutting up to 3.30m height for the following surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size.90cm.x 60cm and 10 B.G stiffened with mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak (country wood) joists of size 10cm x 6.5cm. spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centres complete complying with standard specification (The payment for centering shall be given after the concrete is laid.) The retrieved materials should be taken back by the contractor.

upto Basement

Lintel and Sunshade

Roof Slab

Reinforcement Cement Concrete 1:1.5:3 using 20 mm ISS HBG metal for all RCC item of works excluding cost of reinforcement and fabricating charges, centering and shuttering but icluding curing and providing fixtures like fan clamps in the RCC floor or roof vibrators, finishing, curing etc. complete and also fixing fixtures like fan clamps in the RCC floor / roof slab wherever necessary and the bearing surfaces of walls, beams shall be plastered with cement mortar 1:3 (one cement and three sand) and kraft paper laid etc.complete complying with standard specifications and as directed by the departmental officers.

upto Basement

Lintel and Sunshade

Roof Slab

Supplying, fabricating and placing in position of mild steel or ribbed tor steel grills for all RCC works as per the design given including cost of steel and binding wire in all floors etc.complete complying with standard specifications. The contractor ha

Plastering the surface of walls with cement mortar 1:5 (one of cement and six of sand) 12mm thick in all floors Finishing smooth, scaffolding, curing etc., complete complying with standard specification as directed by the departmental officers.

Supply and applying of two coats of putty of 3mm tk over the exposed RCC surface thorougly cleaned out of dust and scrubbing as per specifications etc complete.,

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing 25 mm thickness of Granolithic pattern for floor finish with cement concrete 1:2:4 (One of Cement, two of sand and four of hard broken stone jelly) using 10 to 12 mm HBG stone jelly on top surface shall be rubbed smooth finishing and curing etc., complete as per the instruction of departmental officer.

Supply and Delivery Fabrication of MS doors with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete. (Refer TWAD Page No 94)

Steel Door (0.90x2.10m) (Refer TWAD Page No 94, WD-M1485)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supply and Delivery Fabrication of MS windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete.

Steel Windows 0.90mX1.20m (Refer TWAD Page No 94, WD-M1487)

Steel Windows 0.90mX0.60m (Refer TWAD Page No 94, WD-M1488)

Painting the newly plastered wall surfaces with two coats of white washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Painting the newly plastered wall surfaces with two coats of colour washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Supplying and painting two coats new iron work such as steel doors ventilators, window bars etc., (WITHOUT PRIMER)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Labour charges for fixing of doors including all charges etc. ( Refer SOR Page No-35, W-0152 )

Labour charges for fixing of Windows including all charges etc. ( Refer SOR Page No-35, W-0153 )

Provision for Cudappa Slab for Shelf 0.90 x 0.30 x 0.025 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Provision for Cudappa Slab for Shelf 1.77 x 0.60 x 0.040 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Providing rain water harvesting structure including earthwork excavation and filling with brick jally , 40mm jally and sand including cost of material and all labour charges.

Towards supply and delivery of RCC Jolly (20 cm x 20 cm) including cost and conveyance of materails and all labour charges for fixing in position as per std. Specification

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supply and fixing of 110 mm dia pvc pipe for chamber connection

Provision for Septic Tank (2-Nos)

Earthwork excavation in all soils & subsoils includibng all charges etc.,

Earth work excavation for foundation in hard rock requiring blasting & Stacking

Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier etc

Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all R.C.C works with standard specification etc complete.

Reinforced cement concrete 1:1.5:3mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum

Plastering with cement mortar 1:4 mix to 20 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Plastering with cement mortar 1:5 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Provision for electrification

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3 mm thick Hylum sheet cover with TW box And 5 A FT switch with continuous earth connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed Light point / fan point (For electronic Regulator) SD 24

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 mm X 100 mm X 113 mm TW switch box with 3 mm thick Hylum sheet cover for 5 A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for concealed PVC plug point SD 37

Supply and run of 2 of 1.50 sq.mm (22/0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade on 7/20GI bearer wire for service connection mains SD 64

Supply and run of 2 X 4 sq.mm (56 / 0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade in 25 mm dia GI pipe ( Class ' B ' ) suitably bent at both ends with necessary angle iron upright and end supports for mains. SD 70

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1"x1/8"copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW reepersof1" thick an either side with painting with suitable bolt and nuts for fixing theTWplank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Lower End) with suitable necessary connectio SD125

Supply and fixing of 1200 mm ( 48") AC ceiling fan complete with stepped electronic 300 W regulator with 300 mm down rod on the existing clamp. SD 112

Supply and fixing for 9W LED BULB SD 79

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Lower End (SD 506)

Supply and fixing for Arial Fuse Unit SD 130

Construction New Combined house (4-Nos) at Srilankan Tamil Refugees Camp in Mettupatty H/O Mettupatty (Unit-8)

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,-

Cement concrete 1:4:8 (one of cement five of sand and ten of aggregate) using 40mm size hard broken granite stone jelly for flooring including well rammed and rendering the top surface rough to receive the floor finish, curing etc. complete complying with standard specifications. The rate is inclusive of necessary planking for panelling into bays wherever necessary and as directed by the departmental officers.

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Below Basement

Basement to Lintel

Litel to Roof

Supplying and erecting, centering for sides and soffits including necessary supports and strutting up to 3.30m height for the following surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size.90cm.x 60cm and 10 B.G stiffened with mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak (country wood) joists of size 10cm x 6.5cm. spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centres complete complying with standard specification (The payment for centering shall be given after the concrete is laid.) The retrieved materials should be taken back by the contractor.

upto Basement

Lintel and Sunshade

Roof Slab

Reinforcement Cement Concrete 1:1.5:3 using 20 mm ISS HBG metal for all RCC item of works excluding cost of reinforcement and fabricating charges, centering and shuttering but icluding curing and providing fixtures like fan clamps in the RCC floor or roof vibrators, finishing, curing etc. complete and also fixing fixtures like fan clamps in the RCC floor / roof slab wherever necessary and the bearing surfaces of walls, beams shall be plastered with cement mortar 1:3 (one cement and three sand) and kraft paper laid etc.complete complying with standard specifications and as directed by the departmental officers.

upto Basement

Lintel and Sunshade

Roof Slab

Supplying, fabricating and placing in position of mild steel or ribbed tor steel grills for all RCC works as per the design given including cost of steel and binding wire in all floors etc.complete complying with standard specifications. The contractor ha

Plastering the surface of walls with cement mortar 1:5 (one of cement and six of sand) 12mm thick in all floors Finishing smooth, scaffolding, curing etc., complete complying with standard specification as directed by the departmental officers.

Supply and applying of two coats of putty of 3mm tk over the exposed RCC surface thorougly cleaned out of dust and scrubbing as per specifications etc complete.,

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing 25 mm thickness of Granolithic pattern for floor finish with cement concrete 1:2:4 (One of Cement, two of sand and four of hard broken stone jelly) using 10 to 12 mm HBG stone jelly on top surface shall be rubbed smooth finishing and curing etc., complete as per the instruction of departmental officer.

Supply and Delivery Fabrication of MS doors with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete. (Refer TWAD Page No 94)

Steel Door (0.90x2.10m) (Refer TWAD Page No 94, WD-M1485)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supply and Delivery Fabrication of MS windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete.

Steel Windows 0.90mX1.20m (Refer TWAD Page No 94, WD-M1487)

Steel Windows 0.90mX0.60m (Refer TWAD Page No 94, WD-M1488)

Painting the newly plastered wall surfaces with two coats of white washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Painting the newly plastered wall surfaces with two coats of colour washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Supplying and painting two coats new iron work such as steel doors ventilators, window bars etc., (WITHOUT PRIMER)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Labour charges for fixing of doors including all charges etc. ( Refer SOR Page No-35, W-0152 )

Labour charges for fixing of Windows including all charges etc. ( Refer SOR Page No-35, W-0153 )

Provision for Cudappa Slab for Shelf 0.90 x 0.30 x 0.025 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Provision for Cudappa Slab for Shelf 1.77 x 0.60 x 0.040 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Providing rain water harvesting structure including earthwork excavation and filling with brick jally , 40mm jally and sand including cost of material and all labour charges.

Towards supply and delivery of RCC Jolly (20 cm x 20 cm) including cost and conveyance of materails and all labour charges for fixing in position as per std. Specification

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supply and fixing of 110 mm dia pvc pipe for chamber connection

Provision for Septic Tank (2-Nos)

Earthwork excavation in all soils & subsoils includibng all charges etc.,

Earth work excavation for foundation in hard rock requiring blasting & Stacking

Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier etc

Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all R.C.C works with standard specification etc complete.

Reinforced cement concrete 1:1.5:3mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum

Plastering with cement mortar 1:4 mix to 20 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Plastering with cement mortar 1:5 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Provision for electrification

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3 mm thick Hylum sheet cover with TW box And 5 A FT switch with continuous earth connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed Light point / fan point (For electronic Regulator) SD 24

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 mm X 100 mm X 113 mm TW switch box with 3 mm thick Hylum sheet cover for 5 A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for concealed PVC plug point SD 37

Supply and run of 2 of 1.50 sq.mm (22/0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade on 7/20GI bearer wire for service connection mains SD 64

Supply and run of 2 X 4 sq.mm (56 / 0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade in 25 mm dia GI pipe ( Class ' B ' ) suitably bent at both ends with necessary angle iron upright and end supports for mains. SD 70

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1"x1/8"copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW reepersof1" thick an either side with painting with suitable bolt and nuts for fixing theTWplank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Lower End) with suitable necessary connectio SD125

Supply and fixing of 1200 mm ( 48") AC ceiling fan complete with stepped electronic 300 W regulator with 300 mm down rod on the existing clamp. SD 112

Supply and fixing for 9W LED BULB SD 79

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Lower End (SD 506)

Supply and fixing for Arial Fuse Unit SD 130

Construction New Combined house (4-Nos) at Srilankan Tamil Refugees Camp in Mettupatty H/O Mettupatty (Unit-9)

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,-

Cement concrete 1:4:8 (one of cement five of sand and ten of aggregate) using 40mm size hard broken granite stone jelly for flooring including well rammed and rendering the top surface rough to receive the floor finish, curing etc. complete complying with standard specifications. The rate is inclusive of necessary planking for panelling into bays wherever necessary and as directed by the departmental officers.

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Below Basement

Basement to Lintel

Litel to Roof

Supplying and erecting, centering for sides and soffits including necessary supports and strutting up to 3.30m height for the following surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size.90cm.x 60cm and 10 B.G stiffened with mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak (country wood) joists of size 10cm x 6.5cm. spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centres complete complying with standard specification (The payment for centering shall be given after the concrete is laid.) The retrieved materials should be taken back by the contractor.

upto Basement

Lintel and Sunshade

Roof Slab

Reinforcement Cement Concrete 1:1.5:3 using 20 mm ISS HBG metal for all RCC item of works excluding cost of reinforcement and fabricating charges, centering and shuttering but icluding curing and providing fixtures like fan clamps in the RCC floor or roof vibrators, finishing, curing etc. complete and also fixing fixtures like fan clamps in the RCC floor / roof slab wherever necessary and the bearing surfaces of walls, beams shall be plastered with cement mortar 1:3 (one cement and three sand) and kraft paper laid etc.complete complying with standard specifications and as directed by the departmental officers.

upto Basement

Lintel and Sunshade

Roof Slab

Supplying, fabricating and placing in position of mild steel or ribbed tor steel grills for all RCC works as per the design given including cost of steel and binding wire in all floors etc.complete complying with standard specifications. The contractor ha

Plastering the surface of walls with cement mortar 1:5 (one of cement and six of sand) 12mm thick in all floors Finishing smooth, scaffolding, curing etc., complete complying with standard specification as directed by the departmental officers.

Supply and applying of two coats of putty of 3mm tk over the exposed RCC surface thorougly cleaned out of dust and scrubbing as per specifications etc complete.,

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing 25 mm thickness of Granolithic pattern for floor finish with cement concrete 1:2:4 (One of Cement, two of sand and four of hard broken stone jelly) using 10 to 12 mm HBG stone jelly on top surface shall be rubbed smooth finishing and curing etc., complete as per the instruction of departmental officer.

Supply and Delivery Fabrication of MS doors with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete. (Refer TWAD Page No 94)

Steel Door (0.90x2.10m) (Refer TWAD Page No 94, WD-M1485)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supply and Delivery Fabrication of MS windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete.

Steel Windows 0.90mX1.20m (Refer TWAD Page No 94, WD-M1487)

Steel Windows 0.90mX0.60m (Refer TWAD Page No 94, WD-M1488)

Painting the newly plastered wall surfaces with two coats of white washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Painting the newly plastered wall surfaces with two coats of colour washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Supplying and painting two coats new iron work such as steel doors ventilators, window bars etc., (WITHOUT PRIMER)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Labour charges for fixing of doors including all charges etc. ( Refer SOR Page No-35, W-0152 )

Labour charges for fixing of Windows including all charges etc. ( Refer SOR Page No-35, W-0153 )

Provision for Cudappa Slab for Shelf 0.90 x 0.30 x 0.025 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Provision for Cudappa Slab for Shelf 1.77 x 0.60 x 0.040 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Providing rain water harvesting structure including earthwork excavation and filling with brick jally , 40mm jally and sand including cost of material and all labour charges.

Towards supply and delivery of RCC Jolly (20 cm x 20 cm) including cost and conveyance of materails and all labour charges for fixing in position as per std. Specification

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supply and fixing of 110 mm dia pvc pipe for chamber connection

Provision for Septic Tank (2-Nos)

Earthwork excavation in all soils & subsoils includibng all charges etc.,

Earth work excavation for foundation in hard rock requiring blasting & Stacking

Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier etc

Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all R.C.C works with standard specification etc complete.

Reinforced cement concrete 1:1.5:3mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum

Plastering with cement mortar 1:4 mix to 20 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Plastering with cement mortar 1:5 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Provision for electrification

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3 mm thick Hylum sheet cover with TW box And 5 A FT switch with continuous earth connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed Light point / fan point (For electronic Regulator) SD 24

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 mm X 100 mm X 113 mm TW switch box with 3 mm thick Hylum sheet cover for 5 A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for concealed PVC plug point SD 37

Supply and run of 2 of 1.50 sq.mm (22/0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade on 7/20GI bearer wire for service connection mains SD 64

Supply and run of 2 X 4 sq.mm (56 / 0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade in 25 mm dia GI pipe ( Class ' B ' ) suitably bent at both ends with necessary angle iron upright and end supports for mains. SD 70

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1"x1/8"copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW reepersof1" thick an either side with painting with suitable bolt and nuts for fixing theTWplank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Lower End) with suitable necessary connectio SD125

Supply and fixing of 1200 mm ( 48") AC ceiling fan complete with stepped electronic 300 W regulator with 300 mm down rod on the existing clamp. SD 112

Supply and fixing for 9W LED BULB SD 79

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Lower End (SD 506)

Supply and fixing for Arial Fuse Unit SD 130

Construction New Combined house (4-Nos) at Srilankan Tamil Refugees Camp in Mettupatty H/O Mettupatty (Unit-10)

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,-

Cement concrete 1:4:8 (one of cement five of sand and ten of aggregate) using 40mm size hard broken granite stone jelly for flooring including well rammed and rendering the top surface rough to receive the floor finish, curing etc. complete complying with standard specifications. The rate is inclusive of necessary planking for panelling into bays wherever necessary and as directed by the departmental officers.

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Below Basement

Basement to Lintel

Litel to Roof

Supplying and erecting, centering for sides and soffits including necessary supports and strutting up to 3.30m height for the following surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size.90cm.x 60cm and 10 B.G stiffened with mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak (country wood) joists of size 10cm x 6.5cm. spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centres complete complying with standard specification (The payment for centering shall be given after the concrete is laid.) The retrieved materials should be taken back by the contractor.

upto Basement

Lintel and Sunshade

Roof Slab

Reinforcement Cement Concrete 1:1.5:3 using 20 mm ISS HBG metal for all RCC item of works excluding cost of reinforcement and fabricating charges, centering and shuttering but icluding curing and providing fixtures like fan clamps in the RCC floor or roof vibrators, finishing, curing etc. complete and also fixing fixtures like fan clamps in the RCC floor / roof slab wherever necessary and the bearing surfaces of walls, beams shall be plastered with cement mortar 1:3 (one cement and three sand) and kraft paper laid etc.complete complying with standard specifications and as directed by the departmental officers.

upto Basement

Lintel and Sunshade

Roof Slab

Supplying, fabricating and placing in position of mild steel or ribbed tor steel grills for all RCC works as per the design given including cost of steel and binding wire in all floors etc.complete complying with standard specifications. The contractor ha

Plastering the surface of walls with cement mortar 1:5 (one of cement and six of sand) 12mm thick in all floors Finishing smooth, scaffolding, curing etc., complete complying with standard specification as directed by the departmental officers.

Supply and applying of two coats of putty of 3mm tk over the exposed RCC surface thorougly cleaned out of dust and scrubbing as per specifications etc complete.,

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing 25 mm thickness of Granolithic pattern for floor finish with cement concrete 1:2:4 (One of Cement, two of sand and four of hard broken stone jelly) using 10 to 12 mm HBG stone jelly on top surface shall be rubbed smooth finishing and curing etc., complete as per the instruction of departmental officer.

Supply and Delivery Fabrication of MS doors with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete. (Refer TWAD Page No 94)

Steel Door (0.90x2.10m) (Refer TWAD Page No 94, WD-M1485)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supply and Delivery Fabrication of MS windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete.

Steel Windows 0.90mX1.20m (Refer TWAD Page No 94, WD-M1487)

Steel Windows 0.90mX0.60m (Refer TWAD Page No 94, WD-M1488)

Painting the newly plastered wall surfaces with two coats of white washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Painting the newly plastered wall surfaces with two coats of colour washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Supplying and painting two coats new iron work such as steel doors ventilators, window bars etc., (WITHOUT PRIMER)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Labour charges for fixing of doors including all charges etc. ( Refer SOR Page No-35, W-0152 )

Labour charges for fixing of Windows including all charges etc. ( Refer SOR Page No-35, W-0153 )

Provision for Cudappa Slab for Shelf 0.90 x 0.30 x 0.025 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Provision for Cudappa Slab for Shelf 1.77 x 0.60 x 0.040 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Providing rain water harvesting structure including earthwork excavation and filling with brick jally , 40mm jally and sand including cost of material and all labour charges.

Towards supply and delivery of RCC Jolly (20 cm x 20 cm) including cost and conveyance of materails and all labour charges for fixing in position as per std. Specification

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supply and fixing of 110 mm dia pvc pipe for chamber connection

Provision for Septic Tank (2-Nos)

Earthwork excavation in all soils & subsoils includibng all charges etc.,

Earth work excavation for foundation in hard rock requiring blasting & Stacking

Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier etc

Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all R.C.C works with standard specification etc complete.

Reinforced cement concrete 1:1.5:3mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum

Plastering with cement mortar 1:4 mix to 20 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Plastering with cement mortar 1:5 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Provision for electrification

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3 mm thick Hylum sheet cover with TW box And 5 A FT switch with continuous earth connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed Light point / fan point (For electronic Regulator) SD 24

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 mm X 100 mm X 113 mm TW switch box with 3 mm thick Hylum sheet cover for 5 A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for concealed PVC plug point SD 37

Supply and run of 2 of 1.50 sq.mm (22/0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade on 7/20GI bearer wire for service connection mains SD 64

Supply and run of 2 X 4 sq.mm (56 / 0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade in 25 mm dia GI pipe ( Class ' B ' ) suitably bent at both ends with necessary angle iron upright and end supports for mains. SD 70

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1"x1/8"copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW reepersof1" thick an either side with painting with suitable bolt and nuts for fixing theTWplank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Lower End) with suitable necessary connectio SD125

Supply and fixing of 1200 mm ( 48") AC ceiling fan complete with stepped electronic 300 W regulator with 300 mm down rod on the existing clamp. SD 112

Supply and fixing for 9W LED BULB SD 79

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Lower End (SD 506)

Supply and fixing for Arial Fuse Unit SD 130

Construction New Combined house (4-Nos) at Srilankan Tamil Refugees Camp in Mettupatty H/O Mettupatty (Unit-11)

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,-

Cement concrete 1:4:8 (one of cement five of sand and ten of aggregate) using 40mm size hard broken granite stone jelly for flooring including well rammed and rendering the top surface rough to receive the floor finish, curing etc. complete complying with standard specifications. The rate is inclusive of necessary planking for panelling into bays wherever necessary and as directed by the departmental officers.

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Below Basement

Basement to Lintel

Litel to Roof

Supplying and erecting, centering for sides and soffits including necessary supports and strutting up to 3.30m height for the following surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size.90cm.x 60cm and 10 B.G stiffened with mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak (country wood) joists of size 10cm x 6.5cm. spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centres complete complying with standard specification (The payment for centering shall be given after the concrete is laid.) The retrieved materials should be taken back by the contractor.

upto Basement

Lintel and Sunshade

Roof Slab

Reinforcement Cement Concrete 1:1.5:3 using 20 mm ISS HBG metal for all RCC item of works excluding cost of reinforcement and fabricating charges, centering and shuttering but icluding curing and providing fixtures like fan clamps in the RCC floor or roof vibrators, finishing, curing etc. complete and also fixing fixtures like fan clamps in the RCC floor / roof slab wherever necessary and the bearing surfaces of walls, beams shall be plastered with cement mortar 1:3 (one cement and three sand) and kraft paper laid etc.complete complying with standard specifications and as directed by the departmental officers.

upto Basement

Lintel and Sunshade

Roof Slab

Supplying, fabricating and placing in position of mild steel or ribbed tor steel grills for all RCC works as per the design given including cost of steel and binding wire in all floors etc.complete complying with standard specifications. The contractor ha

Plastering the surface of walls with cement mortar 1:5 (one of cement and six of sand) 12mm thick in all floors Finishing smooth, scaffolding, curing etc., complete complying with standard specification as directed by the departmental officers.

Supply and applying of two coats of putty of 3mm tk over the exposed RCC surface thorougly cleaned out of dust and scrubbing as per specifications etc complete.,

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing 25 mm thickness of Granolithic pattern for floor finish with cement concrete 1:2:4 (One of Cement, two of sand and four of hard broken stone jelly) using 10 to 12 mm HBG stone jelly on top surface shall be rubbed smooth finishing and curing etc., complete as per the instruction of departmental officer.

Supply and Delivery Fabrication of MS doors with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete. (Refer TWAD Page No 94)

Steel Door (0.90x2.10m) (Refer TWAD Page No 94, WD-M1485)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supply and Delivery Fabrication of MS windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete.

Steel Windows 0.90mX1.20m (Refer TWAD Page No 94, WD-M1487)

Steel Windows 0.90mX0.60m (Refer TWAD Page No 94, WD-M1488)

Painting the newly plastered wall surfaces with two coats of white washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Painting the newly plastered wall surfaces with two coats of colour washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Supplying and painting two coats new iron work such as steel doors ventilators, window bars etc., (WITHOUT PRIMER)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Labour charges for fixing of doors including all charges etc. ( Refer SOR Page No-35, W-0152 )

Labour charges for fixing of Windows including all charges etc. ( Refer SOR Page No-35, W-0153 )

Provision for Cudappa Slab for Shelf 0.90 x 0.30 x 0.025 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Provision for Cudappa Slab for Shelf 1.77 x 0.60 x 0.040 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Providing rain water harvesting structure including earthwork excavation and filling with brick jally , 40mm jally and sand including cost of material and all labour charges.

Towards supply and delivery of RCC Jolly (20 cm x 20 cm) including cost and conveyance of materails and all labour charges for fixing in position as per std. Specification

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supply and fixing of 110 mm dia pvc pipe for chamber connection

Provision for Septic Tank (2-Nos)

Earthwork excavation in all soils & subsoils includibng all charges etc.,

Earth work excavation for foundation in hard rock requiring blasting & Stacking

Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier etc

Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all R.C.C works with standard specification etc complete.

Reinforced cement concrete 1:1.5:3mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum

Plastering with cement mortar 1:4 mix to 20 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Plastering with cement mortar 1:5 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Provision for electrification

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3 mm thick Hylum sheet cover with TW box And 5 A FT switch with continuous earth connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed Light point / fan point (For electronic Regulator) SD 24

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 mm X 100 mm X 113 mm TW switch box with 3 mm thick Hylum sheet cover for 5 A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for concealed PVC plug point SD 37

Supply and run of 2 of 1.50 sq.mm (22/0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade on 7/20GI bearer wire for service connection mains SD 64

Supply and run of 2 X 4 sq.mm (56 / 0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade in 25 mm dia GI pipe ( Class ' B ' ) suitably bent at both ends with necessary angle iron upright and end supports for mains. SD 70

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1"x1/8"copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW reepersof1" thick an either side with painting with suitable bolt and nuts for fixing theTWplank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Lower End) with suitable necessary connectio SD125

Supply and fixing of 1200 mm ( 48") AC ceiling fan complete with stepped electronic 300 W regulator with 300 mm down rod on the existing clamp. SD 112

Supply and fixing for 9W LED BULB SD 79

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Lower End (SD 506)

Supply and fixing for Arial Fuse Unit SD 130

Construction New Combined house (4-Nos) at Srilankan Tamil Refugees Camp in Mettupatty H/O Mettupatty (Unit-12)

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,-

Cement concrete 1:4:8 (one of cement five of sand and ten of aggregate) using 40mm size hard broken granite stone jelly for flooring including well rammed and rendering the top surface rough to receive the floor finish, curing etc. complete complying with standard specifications. The rate is inclusive of necessary planking for panelling into bays wherever necessary and as directed by the departmental officers.

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Below Basement

Basement to Lintel

Litel to Roof

Supplying and erecting, centering for sides and soffits including necessary supports and strutting up to 3.30m height for the following surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size.90cm.x 60cm and 10 B.G stiffened with mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak (country wood) joists of size 10cm x 6.5cm. spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centres complete complying with standard specification (The payment for centering shall be given after the concrete is laid.) The retrieved materials should be taken back by the contractor.

upto Basement

Lintel and Sunshade

Roof Slab

Reinforcement Cement Concrete 1:1.5:3 using 20 mm ISS HBG metal for all RCC item of works excluding cost of reinforcement and fabricating charges, centering and shuttering but icluding curing and providing fixtures like fan clamps in the RCC floor or roof vibrators, finishing, curing etc. complete and also fixing fixtures like fan clamps in the RCC floor / roof slab wherever necessary and the bearing surfaces of walls, beams shall be plastered with cement mortar 1:3 (one cement and three sand) and kraft paper laid etc.complete complying with standard specifications and as directed by the departmental officers.

upto Basement

Lintel and Sunshade

Roof Slab

Supplying, fabricating and placing in position of mild steel or ribbed tor steel grills for all RCC works as per the design given including cost of steel and binding wire in all floors etc.complete complying with standard specifications. The contractor ha

Plastering the surface of walls with cement mortar 1:5 (one of cement and six of sand) 12mm thick in all floors Finishing smooth, scaffolding, curing etc., complete complying with standard specification as directed by the departmental officers.

Supply and applying of two coats of putty of 3mm tk over the exposed RCC surface thorougly cleaned out of dust and scrubbing as per specifications etc complete.,

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing 25 mm thickness of Granolithic pattern for floor finish with cement concrete 1:2:4 (One of Cement, two of sand and four of hard broken stone jelly) using 10 to 12 mm HBG stone jelly on top surface shall be rubbed smooth finishing and curing etc., complete as per the instruction of departmental officer.

Supply and Delivery Fabrication of MS doors with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete. (Refer TWAD Page No 94)

Steel Door (0.90x2.10m) (Refer TWAD Page No 94, WD-M1485)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supply and Delivery Fabrication of MS windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete.

Steel Windows 0.90mX1.20m (Refer TWAD Page No 94, WD-M1487)

Steel Windows 0.90mX0.60m (Refer TWAD Page No 94, WD-M1488)

Painting the newly plastered wall surfaces with two coats of white washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Painting the newly plastered wall surfaces with two coats of colour washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Supplying and painting two coats new iron work such as steel doors ventilators, window bars etc., (WITHOUT PRIMER)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Labour charges for fixing of doors including all charges etc. ( Refer SOR Page No-35, W-0152 )

Labour charges for fixing of Windows including all charges etc. ( Refer SOR Page No-35, W-0153 )

Provision for Cudappa Slab for Shelf 0.90 x 0.30 x 0.025 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Provision for Cudappa Slab for Shelf 1.77 x 0.60 x 0.040 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Providing rain water harvesting structure including earthwork excavation and filling with brick jally , 40mm jally and sand including cost of material and all labour charges.

Towards supply and delivery of RCC Jolly (20 cm x 20 cm) including cost and conveyance of materails and all labour charges for fixing in position as per std. Specification

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supply and fixing of 110 mm dia pvc pipe for chamber connection

Provision for Septic Tank (2-Nos)

Earthwork excavation in all soils & subsoils includibng all charges etc.,

Earth work excavation for foundation in hard rock requiring blasting & Stacking

Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier etc

Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all R.C.C works with standard specification etc complete.

Reinforced cement concrete 1:1.5:3mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum

Plastering with cement mortar 1:4 mix to 20 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Plastering with cement mortar 1:5 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Provision for electrification

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3 mm thick Hylum sheet cover with TW box And 5 A FT switch with continuous earth connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed Light point / fan point (For electronic Regulator) SD 24

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 mm X 100 mm X 113 mm TW switch box with 3 mm thick Hylum sheet cover for 5 A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for concealed PVC plug point SD 37

Supply and run of 2 of 1.50 sq.mm (22/0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade on 7/20GI bearer wire for service connection mains SD 64

Supply and run of 2 X 4 sq.mm (56 / 0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade in 25 mm dia GI pipe ( Class ' B ' ) suitably bent at both ends with necessary angle iron upright and end supports for mains. SD 70

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1"x1/8"copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW reepersof1" thick an either side with painting with suitable bolt and nuts for fixing theTWplank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Lower End) with suitable necessary connectio SD125

Supply and fixing of 1200 mm ( 48") AC ceiling fan complete with stepped electronic 300 W regulator with 300 mm down rod on the existing clamp. SD 112

Supply and fixing for 9W LED BULB SD 79

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Lower End (SD 506)

Supply and fixing for Arial Fuse Unit SD 130

Construction New Combined house (4-Nos) at Srilankan Tamil Refugees Camp in Mettupatty H/O Mettupatty (Unit-13)

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,-

Cement concrete 1:4:8 (one of cement five of sand and ten of aggregate) using 40mm size hard broken granite stone jelly for flooring including well rammed and rendering the top surface rough to receive the floor finish, curing etc. complete complying with standard specifications. The rate is inclusive of necessary planking for panelling into bays wherever necessary and as directed by the departmental officers.

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Below Basement

Basement to Lintel

Litel to Roof

Supplying and erecting, centering for sides and soffits including necessary supports and strutting up to 3.30m height for the following surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size.90cm.x 60cm and 10 B.G stiffened with mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak (country wood) joists of size 10cm x 6.5cm. spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centres complete complying with standard specification (The payment for centering shall be given after the concrete is laid.) The retrieved materials should be taken back by the contractor.

upto Basement

Lintel and Sunshade

Roof Slab

Reinforcement Cement Concrete 1:1.5:3 using 20 mm ISS HBG metal for all RCC item of works excluding cost of reinforcement and fabricating charges, centering and shuttering but icluding curing and providing fixtures like fan clamps in the RCC floor or roof vibrators, finishing, curing etc. complete and also fixing fixtures like fan clamps in the RCC floor / roof slab wherever necessary and the bearing surfaces of walls, beams shall be plastered with cement mortar 1:3 (one cement and three sand) and kraft paper laid etc.complete complying with standard specifications and as directed by the departmental officers.

upto Basement

Lintel and Sunshade

Roof Slab

Supplying, fabricating and placing in position of mild steel or ribbed tor steel grills for all RCC works as per the design given including cost of steel and binding wire in all floors etc.complete complying with standard specifications. The contractor ha

Plastering the surface of walls with cement mortar 1:5 (one of cement and six of sand) 12mm thick in all floors Finishing smooth, scaffolding, curing etc., complete complying with standard specification as directed by the departmental officers.

Supply and applying of two coats of putty of 3mm tk over the exposed RCC surface thorougly cleaned out of dust and scrubbing as per specifications etc complete.,

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing 25 mm thickness of Granolithic pattern for floor finish with cement concrete 1:2:4 (One of Cement, two of sand and four of hard broken stone jelly) using 10 to 12 mm HBG stone jelly on top surface shall be rubbed smooth finishing and curing etc., complete as per the instruction of departmental officer.

Supply and Delivery Fabrication of MS doors with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete. (Refer TWAD Page No 94)

Steel Door (0.90x2.10m) (Refer TWAD Page No 94, WD-M1485)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supply and Delivery Fabrication of MS windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete.

Steel Windows 0.90mX1.20m (Refer TWAD Page No 94, WD-M1487)

Steel Windows 0.90mX0.60m (Refer TWAD Page No 94, WD-M1488)

Painting the newly plastered wall surfaces with two coats of white washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Painting the newly plastered wall surfaces with two coats of colour washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Supplying and painting two coats new iron work such as steel doors ventilators, window bars etc., (WITHOUT PRIMER)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Labour charges for fixing of doors including all charges etc. ( Refer SOR Page No-35, W-0152 )

Labour charges for fixing of Windows including all charges etc. ( Refer SOR Page No-35, W-0153 )

Provision for Cudappa Slab for Shelf 0.90 x 0.30 x 0.025 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Provision for Cudappa Slab for Shelf 1.77 x 0.60 x 0.040 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Providing rain water harvesting structure including earthwork excavation and filling with brick jally , 40mm jally and sand including cost of material and all labour charges.

Towards supply and delivery of RCC Jolly (20 cm x 20 cm) including cost and conveyance of materails and all labour charges for fixing in position as per std. Specification

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supply and fixing of 110 mm dia pvc pipe for chamber connection

Provision for Septic Tank (2-Nos)

Earthwork excavation in all soils & subsoils includibng all charges etc.,

Earth work excavation for foundation in hard rock requiring blasting & Stacking

Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier etc

Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all R.C.C works with standard specification etc complete.

Reinforced cement concrete 1:1.5:3mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum

Plastering with cement mortar 1:4 mix to 20 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Plastering with cement mortar 1:5 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Provision for electrification

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3 mm thick Hylum sheet cover with TW box And 5 A FT switch with continuous earth connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed Light point / fan point (For electronic Regulator) SD 24

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 mm X 100 mm X 113 mm TW switch box with 3 mm thick Hylum sheet cover for 5 A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for concealed PVC plug point SD 37

Supply and run of 2 of 1.50 sq.mm (22/0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade on 7/20GI bearer wire for service connection mains SD 64

Supply and run of 2 X 4 sq.mm (56 / 0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade in 25 mm dia GI pipe ( Class ' B ' ) suitably bent at both ends with necessary angle iron upright and end supports for mains. SD 70

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1"x1/8"copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW reepersof1" thick an either side with painting with suitable bolt and nuts for fixing theTWplank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Lower End) with suitable necessary connectio SD125

Supply and fixing of 1200 mm ( 48") AC ceiling fan complete with stepped electronic 300 W regulator with 300 mm down rod on the existing clamp. SD 112

Supply and fixing for 9W LED BULB SD 79

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Lower End (SD 506)

Supply and fixing for Arial Fuse Unit SD 130

Construction New Combined house (4-Nos) at Srilankan Tamil Refugees Camp in Mettupatty H/O Mettupatty (Unit-14)

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,-

Cement concrete 1:4:8 (one of cement five of sand and ten of aggregate) using 40mm size hard broken granite stone jelly for flooring including well rammed and rendering the top surface rough to receive the floor finish, curing etc. complete complying with standard specifications. The rate is inclusive of necessary planking for panelling into bays wherever necessary and as directed by the departmental officers.

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Below Basement

Basement to Lintel

Litel to Roof

Supplying and erecting, centering for sides and soffits including necessary supports and strutting up to 3.30m height for the following surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size.90cm.x 60cm and 10 B.G stiffened with mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak (country wood) joists of size 10cm x 6.5cm. spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centres complete complying with standard specification (The payment for centering shall be given after the concrete is laid.) The retrieved materials should be taken back by the contractor.

upto Basement

Lintel and Sunshade

Roof Slab

Reinforcement Cement Concrete 1:1.5:3 using 20 mm ISS HBG metal for all RCC item of works excluding cost of reinforcement and fabricating charges, centering and shuttering but icluding curing and providing fixtures like fan clamps in the RCC floor or roof vibrators, finishing, curing etc. complete and also fixing fixtures like fan clamps in the RCC floor / roof slab wherever necessary and the bearing surfaces of walls, beams shall be plastered with cement mortar 1:3 (one cement and three sand) and kraft paper laid etc.complete complying with standard specifications and as directed by the departmental officers.

upto Basement

Lintel and Sunshade

Roof Slab

Supplying, fabricating and placing in position of mild steel or ribbed tor steel grills for all RCC works as per the design given including cost of steel and binding wire in all floors etc.complete complying with standard specifications. The contractor ha

Plastering the surface of walls with cement mortar 1:5 (one of cement and six of sand) 12mm thick in all floors Finishing smooth, scaffolding, curing etc., complete complying with standard specification as directed by the departmental officers.

Supply and applying of two coats of putty of 3mm tk over the exposed RCC surface thorougly cleaned out of dust and scrubbing as per specifications etc complete.,

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing 25 mm thickness of Granolithic pattern for floor finish with cement concrete 1:2:4 (One of Cement, two of sand and four of hard broken stone jelly) using 10 to 12 mm HBG stone jelly on top surface shall be rubbed smooth finishing and curing etc., complete as per the instruction of departmental officer.

Supply and Delivery Fabrication of MS doors with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete. (Refer TWAD Page No 94)

Steel Door (0.90x2.10m) (Refer TWAD Page No 94, WD-M1485)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supply and Delivery Fabrication of MS windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete.

Steel Windows 0.90mX1.20m (Refer TWAD Page No 94, WD-M1487)

Steel Windows 0.90mX0.60m (Refer TWAD Page No 94, WD-M1488)

Painting the newly plastered wall surfaces with two coats of white washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Painting the newly plastered wall surfaces with two coats of colour washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Supplying and painting two coats new iron work such as steel doors ventilators, window bars etc., (WITHOUT PRIMER)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Labour charges for fixing of doors including all charges etc. ( Refer SOR Page No-35, W-0152 )

Labour charges for fixing of Windows including all charges etc. ( Refer SOR Page No-35, W-0153 )

Provision for Cudappa Slab for Shelf 0.90 x 0.30 x 0.025 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Provision for Cudappa Slab for Shelf 1.77 x 0.60 x 0.040 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Providing rain water harvesting structure including earthwork excavation and filling with brick jally , 40mm jally and sand including cost of material and all labour charges.

Towards supply and delivery of RCC Jolly (20 cm x 20 cm) including cost and conveyance of materails and all labour charges for fixing in position as per std. Specification

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supply and fixing of 110 mm dia pvc pipe for chamber connection

Provision for Septic Tank (2-Nos)

Earthwork excavation in all soils & subsoils includibng all charges etc.,

Earth work excavation for foundation in hard rock requiring blasting & Stacking

Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier etc

Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all R.C.C works with standard specification etc complete.

Reinforced cement concrete 1:1.5:3mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum

Plastering with cement mortar 1:4 mix to 20 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Plastering with cement mortar 1:5 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Provision for electrification

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3 mm thick Hylum sheet cover with TW box And 5 A FT switch with continuous earth connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed Light point / fan point (For electronic Regulator) SD 24

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 mm X 100 mm X 113 mm TW switch box with 3 mm thick Hylum sheet cover for 5 A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for concealed PVC plug point SD 37

Supply and run of 2 of 1.50 sq.mm (22/0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade on 7/20GI bearer wire for service connection mains SD 64

Supply and run of 2 X 4 sq.mm (56 / 0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade in 25 mm dia GI pipe ( Class ' B ' ) suitably bent at both ends with necessary angle iron upright and end supports for mains. SD 70

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1"x1/8"copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW reepersof1" thick an either side with painting with suitable bolt and nuts for fixing theTWplank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Lower End) with suitable necessary connectio SD125

Supply and fixing of 1200 mm ( 48") AC ceiling fan complete with stepped electronic 300 W regulator with 300 mm down rod on the existing clamp. SD 112

Supply and fixing for 9W LED BULB SD 79

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Lower End (SD 506)

Supply and fixing for Arial Fuse Unit SD 130

Construction New Combined house (4-Nos) at Srilankan Tamil Refugees Camp in Mettupatty H/O Mettupatty (Unit-15)

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,-

Cement concrete 1:4:8 (one of cement five of sand and ten of aggregate) using 40mm size hard broken granite stone jelly for flooring including well rammed and rendering the top surface rough to receive the floor finish, curing etc. complete complying with standard specifications. The rate is inclusive of necessary planking for panelling into bays wherever necessary and as directed by the departmental officers.

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Below Basement

Basement to Lintel

Litel to Roof

Supplying and erecting, centering for sides and soffits including necessary supports and strutting up to 3.30m height for the following surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size.90cm.x 60cm and 10 B.G stiffened with mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak (country wood) joists of size 10cm x 6.5cm. spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centres complete complying with standard specification (The payment for centering shall be given after the concrete is laid.) The retrieved materials should be taken back by the contractor.

upto Basement

Lintel and Sunshade

Roof Slab

Reinforcement Cement Concrete 1:1.5:3 using 20 mm ISS HBG metal for all RCC item of works excluding cost of reinforcement and fabricating charges, centering and shuttering but icluding curing and providing fixtures like fan clamps in the RCC floor or roof vibrators, finishing, curing etc. complete and also fixing fixtures like fan clamps in the RCC floor / roof slab wherever necessary and the bearing surfaces of walls, beams shall be plastered with cement mortar 1:3 (one cement and three sand) and kraft paper laid etc.complete complying with standard specifications and as directed by the departmental officers.

upto Basement

Lintel and Sunshade

Roof Slab

Supplying, fabricating and placing in position of mild steel or ribbed tor steel grills for all RCC works as per the design given including cost of steel and binding wire in all floors etc.complete complying with standard specifications. The contractor ha

Plastering the surface of walls with cement mortar 1:5 (one of cement and six of sand) 12mm thick in all floors Finishing smooth, scaffolding, curing etc., complete complying with standard specification as directed by the departmental officers.

Supply and applying of two coats of putty of 3mm tk over the exposed RCC surface thorougly cleaned out of dust and scrubbing as per specifications etc complete.,

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing 25 mm thickness of Granolithic pattern for floor finish with cement concrete 1:2:4 (One of Cement, two of sand and four of hard broken stone jelly) using 10 to 12 mm HBG stone jelly on top surface shall be rubbed smooth finishing and curing etc., complete as per the instruction of departmental officer.

Supply and Delivery Fabrication of MS doors with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete. (Refer TWAD Page No 94)

Steel Door (0.90x2.10m) (Refer TWAD Page No 94, WD-M1485)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supply and Delivery Fabrication of MS windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete.

Steel Windows 0.90mX1.20m (Refer TWAD Page No 94, WD-M1487)

Steel Windows 0.90mX0.60m (Refer TWAD Page No 94, WD-M1488)

Painting the newly plastered wall surfaces with two coats of white washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Painting the newly plastered wall surfaces with two coats of colour washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Supplying and painting two coats new iron work such as steel doors ventilators, window bars etc., (WITHOUT PRIMER)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Labour charges for fixing of doors including all charges etc. ( Refer SOR Page No-35, W-0152 )

Labour charges for fixing of Windows including all charges etc. ( Refer SOR Page No-35, W-0153 )

Provision for Cudappa Slab for Shelf 0.90 x 0.30 x 0.025 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Provision for Cudappa Slab for Shelf 1.77 x 0.60 x 0.040 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Providing rain water harvesting structure including earthwork excavation and filling with brick jally , 40mm jally and sand including cost of material and all labour charges.

Towards supply and delivery of RCC Jolly (20 cm x 20 cm) including cost and conveyance of materails and all labour charges for fixing in position as per std. Specification

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supply and fixing of 110 mm dia pvc pipe for chamber connection

Provision for Septic Tank (2-Nos)

Earthwork excavation in all soils & subsoils includibng all charges etc.,

Earth work excavation for foundation in hard rock requiring blasting & Stacking

Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier etc

Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all R.C.C works with standard specification etc complete.

Reinforced cement concrete 1:1.5:3mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum

Plastering with cement mortar 1:4 mix to 20 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Plastering with cement mortar 1:5 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Provision for electrification

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3 mm thick Hylum sheet cover with TW box And 5 A FT switch with continuous earth connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed Light point / fan point (For electronic Regulator) SD 24

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 mm X 100 mm X 113 mm TW switch box with 3 mm thick Hylum sheet cover for 5 A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for concealed PVC plug point SD 37

Supply and run of 2 of 1.50 sq.mm (22/0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade on 7/20GI bearer wire for service connection mains SD 64

Supply and run of 2 X 4 sq.mm (56 / 0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade in 25 mm dia GI pipe ( Class ' B ' ) suitably bent at both ends with necessary angle iron upright and end supports for mains. SD 70

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1"x1/8"copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW reepersof1" thick an either side with painting with suitable bolt and nuts for fixing theTWplank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Lower End) with suitable necessary connectio SD125

Supply and fixing of 1200 mm ( 48") AC ceiling fan complete with stepped electronic 300 W regulator with 300 mm down rod on the existing clamp. SD 112

Supply and fixing for 9W LED BULB SD 79

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Lower End (SD 506)

Supply and fixing for Arial Fuse Unit SD 130

Construction New Combined house (4-Nos) at Srilankan Tamil Refugees Camp in Mettupatty H/O Mettupatty (Unit-16)

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,-

Cement concrete 1:4:8 (one of cement five of sand and ten of aggregate) using 40mm size hard broken granite stone jelly for flooring including well rammed and rendering the top surface rough to receive the floor finish, curing etc. complete complying with standard specifications. The rate is inclusive of necessary planking for panelling into bays wherever necessary and as directed by the departmental officers.

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Below Basement

Basement to Lintel

Litel to Roof

Supplying and erecting, centering for sides and soffits including necessary supports and strutting up to 3.30m height for the following surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size.90cm.x 60cm and 10 B.G stiffened with mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak (country wood) joists of size 10cm x 6.5cm. spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centres complete complying with standard specification (The payment for centering shall be given after the concrete is laid.) The retrieved materials should be taken back by the contractor.

upto Basement

Lintel and Sunshade

Roof Slab

Reinforcement Cement Concrete 1:1.5:3 using 20 mm ISS HBG metal for all RCC item of works excluding cost of reinforcement and fabricating charges, centering and shuttering but icluding curing and providing fixtures like fan clamps in the RCC floor or roof vibrators, finishing, curing etc. complete and also fixing fixtures like fan clamps in the RCC floor / roof slab wherever necessary and the bearing surfaces of walls, beams shall be plastered with cement mortar 1:3 (one cement and three sand) and kraft paper laid etc.complete complying with standard specifications and as directed by the departmental officers.

upto Basement

Lintel and Sunshade

Roof Slab

Supplying, fabricating and placing in position of mild steel or ribbed tor steel grills for all RCC works as per the design given including cost of steel and binding wire in all floors etc.complete complying with standard specifications. The contractor ha

Plastering the surface of walls with cement mortar 1:5 (one of cement and six of sand) 12mm thick in all floors Finishing smooth, scaffolding, curing etc., complete complying with standard specification as directed by the departmental officers.

Supply and applying of two coats of putty of 3mm tk over the exposed RCC surface thorougly cleaned out of dust and scrubbing as per specifications etc complete.,

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing 25 mm thickness of Granolithic pattern for floor finish with cement concrete 1:2:4 (One of Cement, two of sand and four of hard broken stone jelly) using 10 to 12 mm HBG stone jelly on top surface shall be rubbed smooth finishing and curing etc., complete as per the instruction of departmental officer.

Supply and Delivery Fabrication of MS doors with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete. (Refer TWAD Page No 94)

Steel Door (0.90x2.10m) (Refer TWAD Page No 94, WD-M1485)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supply and Delivery Fabrication of MS windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete.

Steel Windows 0.90mX1.20m (Refer TWAD Page No 94, WD-M1487)

Steel Windows 0.90mX0.60m (Refer TWAD Page No 94, WD-M1488)

Painting the newly plastered wall surfaces with two coats of white washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Painting the newly plastered wall surfaces with two coats of colour washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Supplying and painting two coats new iron work such as steel doors ventilators, window bars etc., (WITHOUT PRIMER)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Labour charges for fixing of doors including all charges etc. ( Refer SOR Page No-35, W-0152 )

Labour charges for fixing of Windows including all charges etc. ( Refer SOR Page No-35, W-0153 )

Provision for Cudappa Slab for Shelf 0.90 x 0.30 x 0.025 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Provision for Cudappa Slab for Shelf 1.77 x 0.60 x 0.040 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Providing rain water harvesting structure including earthwork excavation and filling with brick jally , 40mm jally and sand including cost of material and all labour charges.

Towards supply and delivery of RCC Jolly (20 cm x 20 cm) including cost and conveyance of materails and all labour charges for fixing in position as per std. Specification

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supply and fixing of 110 mm dia pvc pipe for chamber connection

Provision for Septic Tank (2-Nos)

Earthwork excavation in all soils & subsoils includibng all charges etc.,

Earth work excavation for foundation in hard rock requiring blasting & Stacking

Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier etc

Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all R.C.C works with standard specification etc complete.

Reinforced cement concrete 1:1.5:3mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum

Plastering with cement mortar 1:4 mix to 20 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Plastering with cement mortar 1:5 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Provision for electrification

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3 mm thick Hylum sheet cover with TW box And 5 A FT switch with continuous earth connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed Light point / fan point (For electronic Regulator) SD 24

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 mm X 100 mm X 113 mm TW switch box with 3 mm thick Hylum sheet cover for 5 A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for concealed PVC plug point SD 37

Supply and run of 2 of 1.50 sq.mm (22/0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade on 7/20GI bearer wire for service connection mains SD 64

Supply and run of 2 X 4 sq.mm (56 / 0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade in 25 mm dia GI pipe ( Class ' B ' ) suitably bent at both ends with necessary angle iron upright and end supports for mains. SD 70

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1"x1/8"copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW reepersof1" thick an either side with painting with suitable bolt and nuts for fixing theTWplank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Lower End) with suitable necessary connectio SD125

Supply and fixing of 1200 mm ( 48") AC ceiling fan complete with stepped electronic 300 W regulator with 300 mm down rod on the existing clamp. SD 112

Supply and fixing for 9W LED BULB SD 79

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Lower End (SD 506)

Supply and fixing for Arial Fuse Unit SD 130

Construction New Combined house (4-Nos) at Srilankan Tamil Refugees Camp in Mettupatty H/O Mettupatty (Unit-17)

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,-

Cement concrete 1:4:8 (one of cement five of sand and ten of aggregate) using 40mm size hard broken granite stone jelly for flooring including well rammed and rendering the top surface rough to receive the floor finish, curing etc. complete complying with standard specifications. The rate is inclusive of necessary planking for panelling into bays wherever necessary and as directed by the departmental officers.

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Below Basement

Basement to Lintel

Litel to Roof

Supplying and erecting, centering for sides and soffits including necessary supports and strutting up to 3.30m height for the following surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size.90cm.x 60cm and 10 B.G stiffened with mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak (country wood) joists of size 10cm x 6.5cm. spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centres complete complying with standard specification (The payment for centering shall be given after the concrete is laid.) The retrieved materials should be taken back by the contractor.

upto Basement

Lintel and Sunshade

Roof Slab

Reinforcement Cement Concrete 1:1.5:3 using 20 mm ISS HBG metal for all RCC item of works excluding cost of reinforcement and fabricating charges, centering and shuttering but icluding curing and providing fixtures like fan clamps in the RCC floor or roof vibrators, finishing, curing etc. complete and also fixing fixtures like fan clamps in the RCC floor / roof slab wherever necessary and the bearing surfaces of walls, beams shall be plastered with cement mortar 1:3 (one cement and three sand) and kraft paper laid etc.complete complying with standard specifications and as directed by the departmental officers.

upto Basement

Lintel and Sunshade

Roof Slab

Supplying, fabricating and placing in position of mild steel or ribbed tor steel grills for all RCC works as per the design given including cost of steel and binding wire in all floors etc.complete complying with standard specifications. The contractor ha

Plastering the surface of walls with cement mortar 1:5 (one of cement and six of sand) 12mm thick in all floors Finishing smooth, scaffolding, curing etc., complete complying with standard specification as directed by the departmental officers.

Supply and applying of two coats of putty of 3mm tk over the exposed RCC surface thorougly cleaned out of dust and scrubbing as per specifications etc complete.,

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing 25 mm thickness of Granolithic pattern for floor finish with cement concrete 1:2:4 (One of Cement, two of sand and four of hard broken stone jelly) using 10 to 12 mm HBG stone jelly on top surface shall be rubbed smooth finishing and curing etc., complete as per the instruction of departmental officer.

Supply and Delivery Fabrication of MS doors with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete. (Refer TWAD Page No 94)

Steel Door (0.90x2.10m) (Refer TWAD Page No 94, WD-M1485)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supply and Delivery Fabrication of MS windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete.

Steel Windows 0.90mX1.20m (Refer TWAD Page No 94, WD-M1487)

Steel Windows 0.90mX0.60m (Refer TWAD Page No 94, WD-M1488)

Painting the newly plastered wall surfaces with two coats of white washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Painting the newly plastered wall surfaces with two coats of colour washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Supplying and painting two coats new iron work such as steel doors ventilators, window bars etc., (WITHOUT PRIMER)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Labour charges for fixing of doors including all charges etc. ( Refer SOR Page No-35, W-0152 )

Labour charges for fixing of Windows including all charges etc. ( Refer SOR Page No-35, W-0153 )

Provision for Cudappa Slab for Shelf 0.90 x 0.30 x 0.025 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Provision for Cudappa Slab for Shelf 1.77 x 0.60 x 0.040 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Providing rain water harvesting structure including earthwork excavation and filling with brick jally , 40mm jally and sand including cost of material and all labour charges.

Towards supply and delivery of RCC Jolly (20 cm x 20 cm) including cost and conveyance of materails and all labour charges for fixing in position as per std. Specification

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supply and fixing of 110 mm dia pvc pipe for chamber connection

Provision for Septic Tank (2-Nos)

Earthwork excavation in all soils & subsoils includibng all charges etc.,

Earth work excavation for foundation in hard rock requiring blasting & Stacking

Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier etc

Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all R.C.C works with standard specification etc complete.

Reinforced cement concrete 1:1.5:3mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum

Plastering with cement mortar 1:4 mix to 20 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Plastering with cement mortar 1:5 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Provision for electrification

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3 mm thick Hylum sheet cover with TW box And 5 A FT switch with continuous earth connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed Light point / fan point (For electronic Regulator) SD 24

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 mm X 100 mm X 113 mm TW switch box with 3 mm thick Hylum sheet cover for 5 A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for concealed PVC plug point SD 37

Supply and run of 2 of 1.50 sq.mm (22/0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade on 7/20GI bearer wire for service connection mains SD 64

Supply and run of 2 X 4 sq.mm (56 / 0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade in 25 mm dia GI pipe ( Class ' B ' ) suitably bent at both ends with necessary angle iron upright and end supports for mains. SD 70

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1"x1/8"copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW reepersof1" thick an either side with painting with suitable bolt and nuts for fixing theTWplank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Lower End) with suitable necessary connectio SD125

Supply and fixing of 1200 mm ( 48") AC ceiling fan complete with stepped electronic 300 W regulator with 300 mm down rod on the existing clamp. SD 112

Supply and fixing for 9W LED BULB SD 79

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Lower End (SD 506)

Supply and fixing for Arial Fuse Unit SD 130

Construction New Combined house (4-Nos) at Srilankan Tamil Refugees Camp in Mettupatty H/O Mettupatty (Unit-18)

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,-

Cement concrete 1:4:8 (one of cement five of sand and ten of aggregate) using 40mm size hard broken granite stone jelly for flooring including well rammed and rendering the top surface rough to receive the floor finish, curing etc. complete complying with standard specifications. The rate is inclusive of necessary planking for panelling into bays wherever necessary and as directed by the departmental officers.

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Below Basement

Basement to Lintel

Litel to Roof

Supplying and erecting, centering for sides and soffits including necessary supports and strutting up to 3.30m height for the following surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size.90cm.x 60cm and 10 B.G stiffened with mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak (country wood) joists of size 10cm x 6.5cm. spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centres complete complying with standard specification (The payment for centering shall be given after the concrete is laid.) The retrieved materials should be taken back by the contractor.

upto Basement

Lintel and Sunshade

Roof Slab

Reinforcement Cement Concrete 1:1.5:3 using 20 mm ISS HBG metal for all RCC item of works excluding cost of reinforcement and fabricating charges, centering and shuttering but icluding curing and providing fixtures like fan clamps in the RCC floor or roof vibrators, finishing, curing etc. complete and also fixing fixtures like fan clamps in the RCC floor / roof slab wherever necessary and the bearing surfaces of walls, beams shall be plastered with cement mortar 1:3 (one cement and three sand) and kraft paper laid etc.complete complying with standard specifications and as directed by the departmental officers.

upto Basement

Lintel and Sunshade

Roof Slab

Supplying, fabricating and placing in position of mild steel or ribbed tor steel grills for all RCC works as per the design given including cost of steel and binding wire in all floors etc.complete complying with standard specifications. The contractor ha

Plastering the surface of walls with cement mortar 1:5 (one of cement and six of sand) 12mm thick in all floors Finishing smooth, scaffolding, curing etc., complete complying with standard specification as directed by the departmental officers.

Supply and applying of two coats of putty of 3mm tk over the exposed RCC surface thorougly cleaned out of dust and scrubbing as per specifications etc complete.,

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing 25 mm thickness of Granolithic pattern for floor finish with cement concrete 1:2:4 (One of Cement, two of sand and four of hard broken stone jelly) using 10 to 12 mm HBG stone jelly on top surface shall be rubbed smooth finishing and curing etc., complete as per the instruction of departmental officer.

Supply and Delivery Fabrication of MS doors with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete. (Refer TWAD Page No 94)

Steel Door (0.90x2.10m) (Refer TWAD Page No 94, WD-M1485)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supply and Delivery Fabrication of MS windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete.

Steel Windows 0.90mX1.20m (Refer TWAD Page No 94, WD-M1487)

Steel Windows 0.90mX0.60m (Refer TWAD Page No 94, WD-M1488)

Painting the newly plastered wall surfaces with two coats of white washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Painting the newly plastered wall surfaces with two coats of colour washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Supplying and painting two coats new iron work such as steel doors ventilators, window bars etc., (WITHOUT PRIMER)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Labour charges for fixing of doors including all charges etc. ( Refer SOR Page No-35, W-0152 )

Labour charges for fixing of Windows including all charges etc. ( Refer SOR Page No-35, W-0153 )

Provision for Cudappa Slab for Shelf 0.90 x 0.30 x 0.025 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Provision for Cudappa Slab for Shelf 1.77 x 0.60 x 0.040 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Providing rain water harvesting structure including earthwork excavation and filling with brick jally , 40mm jally and sand including cost of material and all labour charges.

Towards supply and delivery of RCC Jolly (20 cm x 20 cm) including cost and conveyance of materails and all labour charges for fixing in position as per std. Specification

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supply and fixing of 110 mm dia pvc pipe for chamber connection

Provision for Septic Tank (2-Nos)

Earthwork excavation in all soils & subsoils includibng all charges etc.,

Earth work excavation for foundation in hard rock requiring blasting & Stacking

Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier etc

Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all R.C.C works with standard specification etc complete.

Reinforced cement concrete 1:1.5:3mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum

Plastering with cement mortar 1:4 mix to 20 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Plastering with cement mortar 1:5 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Provision for electrification

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3 mm thick Hylum sheet cover with TW box And 5 A FT switch with continuous earth connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed Light point / fan point (For electronic Regulator) SD 24

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 mm X 100 mm X 113 mm TW switch box with 3 mm thick Hylum sheet cover for 5 A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for concealed PVC plug point SD 37

Supply and run of 2 of 1.50 sq.mm (22/0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade on 7/20GI bearer wire for service connection mains SD 64

Supply and run of 2 X 4 sq.mm (56 / 0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade in 25 mm dia GI pipe ( Class ' B ' ) suitably bent at both ends with necessary angle iron upright and end supports for mains. SD 70

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1"x1/8"copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW reepersof1" thick an either side with painting with suitable bolt and nuts for fixing theTWplank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Lower End) with suitable necessary connectio SD125

Supply and fixing of 1200 mm ( 48") AC ceiling fan complete with stepped electronic 300 W regulator with 300 mm down rod on the existing clamp. SD 112

Supply and fixing for 9W LED BULB SD 79

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Lower End (SD 506)

Supply and fixing for Arial Fuse Unit SD 130

Construction New Combined house (4-Nos) at Srilankan Tamil Refugees Camp in Mettupatty H/O Mettupatty (Unit-19)

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,-

Cement concrete 1:4:8 (one of cement five of sand and ten of aggregate) using 40mm size hard broken granite stone jelly for flooring including well rammed and rendering the top surface rough to receive the floor finish, curing etc. complete complying with standard specifications. The rate is inclusive of necessary planking for panelling into bays wherever necessary and as directed by the departmental officers.

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Below Basement

Basement to Lintel

Litel to Roof

Supplying and erecting, centering for sides and soffits including necessary supports and strutting up to 3.30m height for the following surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size.90cm.x 60cm and 10 B.G stiffened with mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak (country wood) joists of size 10cm x 6.5cm. spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centres complete complying with standard specification (The payment for centering shall be given after the concrete is laid.) The retrieved materials should be taken back by the contractor.

upto Basement

Lintel and Sunshade

Roof Slab

Reinforcement Cement Concrete 1:1.5:3 using 20 mm ISS HBG metal for all RCC item of works excluding cost of reinforcement and fabricating charges, centering and shuttering but icluding curing and providing fixtures like fan clamps in the RCC floor or roof vibrators, finishing, curing etc. complete and also fixing fixtures like fan clamps in the RCC floor / roof slab wherever necessary and the bearing surfaces of walls, beams shall be plastered with cement mortar 1:3 (one cement and three sand) and kraft paper laid etc.complete complying with standard specifications and as directed by the departmental officers.

upto Basement

Lintel and Sunshade

Roof Slab

Supplying, fabricating and placing in position of mild steel or ribbed tor steel grills for all RCC works as per the design given including cost of steel and binding wire in all floors etc.complete complying with standard specifications. The contractor ha

Plastering the surface of walls with cement mortar 1:5 (one of cement and six of sand) 12mm thick in all floors Finishing smooth, scaffolding, curing etc., complete complying with standard specification as directed by the departmental officers.

Supply and applying of two coats of putty of 3mm tk over the exposed RCC surface thorougly cleaned out of dust and scrubbing as per specifications etc complete.,

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing 25 mm thickness of Granolithic pattern for floor finish with cement concrete 1:2:4 (One of Cement, two of sand and four of hard broken stone jelly) using 10 to 12 mm HBG stone jelly on top surface shall be rubbed smooth finishing and curing etc., complete as per the instruction of departmental officer.

Supply and Delivery Fabrication of MS doors with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete. (Refer TWAD Page No 94)

Steel Door (0.90x2.10m) (Refer TWAD Page No 94, WD-M1485)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supply and Delivery Fabrication of MS windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete.

Steel Windows 0.90mX1.20m (Refer TWAD Page No 94, WD-M1487)

Steel Windows 0.90mX0.60m (Refer TWAD Page No 94, WD-M1488)

Painting the newly plastered wall surfaces with two coats of white washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Painting the newly plastered wall surfaces with two coats of colour washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Supplying and painting two coats new iron work such as steel doors ventilators, window bars etc., (WITHOUT PRIMER)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Labour charges for fixing of doors including all charges etc. ( Refer SOR Page No-35, W-0152 )

Labour charges for fixing of Windows including all charges etc. ( Refer SOR Page No-35, W-0153 )

Provision for Cudappa Slab for Shelf 0.90 x 0.30 x 0.025 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Provision for Cudappa Slab for Shelf 1.77 x 0.60 x 0.040 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Providing rain water harvesting structure including earthwork excavation and filling with brick jally , 40mm jally and sand including cost of material and all labour charges.

Towards supply and delivery of RCC Jolly (20 cm x 20 cm) including cost and conveyance of materails and all labour charges for fixing in position as per std. Specification

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supply and fixing of 110 mm dia pvc pipe for chamber connection

Provision for Septic Tank (2-Nos)

Earthwork excavation in all soils & subsoils includibng all charges etc.,

Earth work excavation for foundation in hard rock requiring blasting & Stacking

Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier etc

Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all R.C.C works with standard specification etc complete.

Reinforced cement concrete 1:1.5:3mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum

Plastering with cement mortar 1:4 mix to 20 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Plastering with cement mortar 1:5 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Provision for electrification

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3 mm thick Hylum sheet cover with TW box And 5 A FT switch with continuous earth connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed Light point / fan point (For electronic Regulator) SD 24

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 mm X 100 mm X 113 mm TW switch box with 3 mm thick Hylum sheet cover for 5 A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for concealed PVC plug point SD 37

Supply and run of 2 of 1.50 sq.mm (22/0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade on 7/20GI bearer wire for service connection mains SD 64

Supply and run of 2 X 4 sq.mm (56 / 0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade in 25 mm dia GI pipe ( Class ' B ' ) suitably bent at both ends with necessary angle iron upright and end supports for mains. SD 70

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1"x1/8"copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW reepersof1" thick an either side with painting with suitable bolt and nuts for fixing theTWplank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Lower End) with suitable necessary connectio SD125

Supply and fixing of 1200 mm ( 48") AC ceiling fan complete with stepped electronic 300 W regulator with 300 mm down rod on the existing clamp. SD 112

Supply and fixing for 9W LED BULB SD 79

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Lower End (SD 506)

Supply and fixing for Arial Fuse Unit SD 130

Construction New Combined house (4-Nos) at Srilankan Tamil Refugees Camp in Mettupatty H/O Mettupatty (Unit-20)

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,-

Cement concrete 1:4:8 (one of cement five of sand and ten of aggregate) using 40mm size hard broken granite stone jelly for flooring including well rammed and rendering the top surface rough to receive the floor finish, curing etc. complete complying with standard specifications. The rate is inclusive of necessary planking for panelling into bays wherever necessary and as directed by the departmental officers.

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Below Basement

Basement to Lintel

Litel to Roof

Supplying and erecting, centering for sides and soffits including necessary supports and strutting up to 3.30m height for the following surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size.90cm.x 60cm and 10 B.G stiffened with mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak (country wood) joists of size 10cm x 6.5cm. spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centres complete complying with standard specification (The payment for centering shall be given after the concrete is laid.) The retrieved materials should be taken back by the contractor.

upto Basement

Lintel and Sunshade

Roof Slab

Reinforcement Cement Concrete 1:1.5:3 using 20 mm ISS HBG metal for all RCC item of works excluding cost of reinforcement and fabricating charges, centering and shuttering but icluding curing and providing fixtures like fan clamps in the RCC floor or roof vibrators, finishing, curing etc. complete and also fixing fixtures like fan clamps in the RCC floor / roof slab wherever necessary and the bearing surfaces of walls, beams shall be plastered with cement mortar 1:3 (one cement and three sand) and kraft paper laid etc.complete complying with standard specifications and as directed by the departmental officers.

upto Basement

Lintel and Sunshade

Roof Slab

Supplying, fabricating and placing in position of mild steel or ribbed tor steel grills for all RCC works as per the design given including cost of steel and binding wire in all floors etc.complete complying with standard specifications. The contractor ha

Plastering the surface of walls with cement mortar 1:5 (one of cement and six of sand) 12mm thick in all floors Finishing smooth, scaffolding, curing etc., complete complying with standard specification as directed by the departmental officers.

Supply and applying of two coats of putty of 3mm tk over the exposed RCC surface thorougly cleaned out of dust and scrubbing as per specifications etc complete.,

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing 25 mm thickness of Granolithic pattern for floor finish with cement concrete 1:2:4 (One of Cement, two of sand and four of hard broken stone jelly) using 10 to 12 mm HBG stone jelly on top surface shall be rubbed smooth finishing and curing etc., complete as per the instruction of departmental officer.

Supply and Delivery Fabrication of MS doors with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete. (Refer TWAD Page No 94)

Steel Door (0.90x2.10m) (Refer TWAD Page No 94, WD-M1485)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supply and Delivery Fabrication of MS windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete.

Steel Windows 0.90mX1.20m (Refer TWAD Page No 94, WD-M1487)

Steel Windows 0.90mX0.60m (Refer TWAD Page No 94, WD-M1488)

Painting the newly plastered wall surfaces with two coats of white washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Painting the newly plastered wall surfaces with two coats of colour washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Supplying and painting two coats new iron work such as steel doors ventilators, window bars etc., (WITHOUT PRIMER)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Labour charges for fixing of doors including all charges etc. ( Refer SOR Page No-35, W-0152 )

Labour charges for fixing of Windows including all charges etc. ( Refer SOR Page No-35, W-0153 )

Provision for Cudappa Slab for Shelf 0.90 x 0.30 x 0.025 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Provision for Cudappa Slab for Shelf 1.77 x 0.60 x 0.040 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Providing rain water harvesting structure including earthwork excavation and filling with brick jally , 40mm jally and sand including cost of material and all labour charges.

Towards supply and delivery of RCC Jolly (20 cm x 20 cm) including cost and conveyance of materails and all labour charges for fixing in position as per std. Specification

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supply and fixing of 110 mm dia pvc pipe for chamber connection

Provision for Septic Tank (2-Nos)

Earthwork excavation in all soils & subsoils includibng all charges etc.,

Earth work excavation for foundation in hard rock requiring blasting & Stacking

Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier etc

Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all R.C.C works with standard specification etc complete.

Reinforced cement concrete 1:1.5:3mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum

Plastering with cement mortar 1:4 mix to 20 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Plastering with cement mortar 1:5 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Provision for electrification

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3 mm thick Hylum sheet cover with TW box And 5 A FT switch with continuous earth connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed Light point / fan point (For electronic Regulator) SD 24

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 mm X 100 mm X 113 mm TW switch box with 3 mm thick Hylum sheet cover for 5 A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for concealed PVC plug point SD 37

Supply and run of 2 of 1.50 sq.mm (22/0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade on 7/20GI bearer wire for service connection mains SD 64

Supply and run of 2 X 4 sq.mm (56 / 0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade in 25 mm dia GI pipe ( Class ' B ' ) suitably bent at both ends with necessary angle iron upright and end supports for mains. SD 70

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1"x1/8"copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW reepersof1" thick an either side with painting with suitable bolt and nuts for fixing theTWplank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Lower End) with suitable necessary connectio SD125

Supply and fixing of 1200 mm ( 48") AC ceiling fan complete with stepped electronic 300 W regulator with 300 mm down rod on the existing clamp. SD 112

Supply and fixing for 9W LED BULB SD 79

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Lower End (SD 506)

Supply and fixing for Arial Fuse Unit SD 130

Construction New Combined house (4-Nos) at Srilankan Tamil Refugees Camp in Mettupatty H/O Mettupatty (Unit-21)

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,-

Cement concrete 1:4:8 (one of cement five of sand and ten of aggregate) using 40mm size hard broken granite stone jelly for flooring including well rammed and rendering the top surface rough to receive the floor finish, curing etc. complete complying with standard specifications. The rate is inclusive of necessary planking for panelling into bays wherever necessary and as directed by the departmental officers.

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Below Basement

Basement to Lintel

Litel to Roof

Supplying and erecting, centering for sides and soffits including necessary supports and strutting up to 3.30m height for the following surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size.90cm.x 60cm and 10 B.G stiffened with mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak (country wood) joists of size 10cm x 6.5cm. spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centres complete complying with standard specification (The payment for centering shall be given after the concrete is laid.) The retrieved materials should be taken back by the contractor.

upto Basement

Lintel and Sunshade

Roof Slab

Reinforcement Cement Concrete 1:1.5:3 using 20 mm ISS HBG metal for all RCC item of works excluding cost of reinforcement and fabricating charges, centering and shuttering but icluding curing and providing fixtures like fan clamps in the RCC floor or roof vibrators, finishing, curing etc. complete and also fixing fixtures like fan clamps in the RCC floor / roof slab wherever necessary and the bearing surfaces of walls, beams shall be plastered with cement mortar 1:3 (one cement and three sand) and kraft paper laid etc.complete complying with standard specifications and as directed by the departmental officers.

upto Basement

Lintel and Sunshade

Roof Slab

Supplying, fabricating and placing in position of mild steel or ribbed tor steel grills for all RCC works as per the design given including cost of steel and binding wire in all floors etc.complete complying with standard specifications. The contractor ha

Plastering the surface of walls with cement mortar 1:5 (one of cement and six of sand) 12mm thick in all floors Finishing smooth, scaffolding, curing etc., complete complying with standard specification as directed by the departmental officers.

Supply and applying of two coats of putty of 3mm tk over the exposed RCC surface thorougly cleaned out of dust and scrubbing as per specifications etc complete.,

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing 25 mm thickness of Granolithic pattern for floor finish with cement concrete 1:2:4 (One of Cement, two of sand and four of hard broken stone jelly) using 10 to 12 mm HBG stone jelly on top surface shall be rubbed smooth finishing and curing etc., complete as per the instruction of departmental officer.

Supply and Delivery Fabrication of MS doors with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete. (Refer TWAD Page No 94)

Steel Door (0.90x2.10m) (Refer TWAD Page No 94, WD-M1485)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supply and Delivery Fabrication of MS windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete.

Steel Windows 0.90mX1.20m (Refer TWAD Page No 94, WD-M1487)

Steel Windows 0.90mX0.60m (Refer TWAD Page No 94, WD-M1488)

Painting the newly plastered wall surfaces with two coats of white washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Painting the newly plastered wall surfaces with two coats of colour washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Supplying and painting two coats new iron work such as steel doors ventilators, window bars etc., (WITHOUT PRIMER)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Labour charges for fixing of doors including all charges etc. ( Refer SOR Page No-35, W-0152 )

Labour charges for fixing of Windows including all charges etc. ( Refer SOR Page No-35, W-0153 )

Provision for Cudappa Slab for Shelf 0.90 x 0.30 x 0.025 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Provision for Cudappa Slab for Shelf 1.77 x 0.60 x 0.040 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Providing rain water harvesting structure including earthwork excavation and filling with brick jally , 40mm jally and sand including cost of material and all labour charges.

Towards supply and delivery of RCC Jolly (20 cm x 20 cm) including cost and conveyance of materails and all labour charges for fixing in position as per std. Specification

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supply and fixing of 110 mm dia pvc pipe for chamber connection

Provision for Septic Tank (2-Nos)

Earthwork excavation in all soils & subsoils includibng all charges etc.,

Earth work excavation for foundation in hard rock requiring blasting & Stacking

Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier etc

Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all R.C.C works with standard specification etc complete.

Reinforced cement concrete 1:1.5:3mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum

Plastering with cement mortar 1:4 mix to 20 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Plastering with cement mortar 1:5 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Provision for electrification

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3 mm thick Hylum sheet cover with TW box And 5 A FT switch with continuous earth connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed Light point / fan point (For electronic Regulator) SD 24

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 mm X 100 mm X 113 mm TW switch box with 3 mm thick Hylum sheet cover for 5 A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for concealed PVC plug point SD 37

Supply and run of 2 of 1.50 sq.mm (22/0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade on 7/20GI bearer wire for service connection mains SD 64

Supply and run of 2 X 4 sq.mm (56 / 0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade in 25 mm dia GI pipe ( Class ' B ' ) suitably bent at both ends with necessary angle iron upright and end supports for mains. SD 70

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1"x1/8"copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW reepersof1" thick an either side with painting with suitable bolt and nuts for fixing theTWplank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Lower End) with suitable necessary connectio SD125

Supply and fixing of 1200 mm ( 48") AC ceiling fan complete with stepped electronic 300 W regulator with 300 mm down rod on the existing clamp. SD 112

Supply and fixing for 9W LED BULB SD 79

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Lower End (SD 506)

Supply and fixing for Arial Fuse Unit SD 130

Construction New Combined house (4-Nos) at Srilankan Tamil Refugees Camp in Mettupatty H/O Mettupatty (Unit-22)

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,-

Cement concrete 1:4:8 (one of cement five of sand and ten of aggregate) using 40mm size hard broken granite stone jelly for flooring including well rammed and rendering the top surface rough to receive the floor finish, curing etc. complete complying with standard specifications. The rate is inclusive of necessary planking for panelling into bays wherever necessary and as directed by the departmental officers.

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Below Basement

Basement to Lintel

Litel to Roof

Supplying and erecting, centering for sides and soffits including necessary supports and strutting up to 3.30m height for the following surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size.90cm.x 60cm and 10 B.G stiffened with mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak (country wood) joists of size 10cm x 6.5cm. spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centres complete complying with standard specification (The payment for centering shall be given after the concrete is laid.) The retrieved materials should be taken back by the contractor.

upto Basement

Lintel and Sunshade

Roof Slab

Reinforcement Cement Concrete 1:1.5:3 using 20 mm ISS HBG metal for all RCC item of works excluding cost of reinforcement and fabricating charges, centering and shuttering but icluding curing and providing fixtures like fan clamps in the RCC floor or roof vibrators, finishing, curing etc. complete and also fixing fixtures like fan clamps in the RCC floor / roof slab wherever necessary and the bearing surfaces of walls, beams shall be plastered with cement mortar 1:3 (one cement and three sand) and kraft paper laid etc.complete complying with standard specifications and as directed by the departmental officers.

upto Basement

Lintel and Sunshade

Roof Slab

Supplying, fabricating and placing in position of mild steel or ribbed tor steel grills for all RCC works as per the design given including cost of steel and binding wire in all floors etc.complete complying with standard specifications. The contractor ha

Plastering the surface of walls with cement mortar 1:5 (one of cement and six of sand) 12mm thick in all floors Finishing smooth, scaffolding, curing etc., complete complying with standard specification as directed by the departmental officers.

Supply and applying of two coats of putty of 3mm tk over the exposed RCC surface thorougly cleaned out of dust and scrubbing as per specifications etc complete.,

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing 25 mm thickness of Granolithic pattern for floor finish with cement concrete 1:2:4 (One of Cement, two of sand and four of hard broken stone jelly) using 10 to 12 mm HBG stone jelly on top surface shall be rubbed smooth finishing and curing etc., complete as per the instruction of departmental officer.

Supply and Delivery Fabrication of MS doors with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete. (Refer TWAD Page No 94)

Steel Door (0.90x2.10m) (Refer TWAD Page No 94, WD-M1485)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supply and Delivery Fabrication of MS windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete.

Steel Windows 0.90mX1.20m (Refer TWAD Page No 94, WD-M1487)

Steel Windows 0.90mX0.60m (Refer TWAD Page No 94, WD-M1488)

Painting the newly plastered wall surfaces with two coats of white washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Painting the newly plastered wall surfaces with two coats of colour washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Supplying and painting two coats new iron work such as steel doors ventilators, window bars etc., (WITHOUT PRIMER)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Labour charges for fixing of doors including all charges etc. ( Refer SOR Page No-35, W-0152 )

Labour charges for fixing of Windows including all charges etc. ( Refer SOR Page No-35, W-0153 )

Provision for Cudappa Slab for Shelf 0.90 x 0.30 x 0.025 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Provision for Cudappa Slab for Shelf 1.77 x 0.60 x 0.040 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Providing rain water harvesting structure including earthwork excavation and filling with brick jally , 40mm jally and sand including cost of material and all labour charges.

Towards supply and delivery of RCC Jolly (20 cm x 20 cm) including cost and conveyance of materails and all labour charges for fixing in position as per std. Specification

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supply and fixing of 110 mm dia pvc pipe for chamber connection

Provision for Septic Tank (2-Nos)

Earthwork excavation in all soils & subsoils includibng all charges etc.,

Earth work excavation for foundation in hard rock requiring blasting & Stacking

Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier etc

Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all R.C.C works with standard specification etc complete.

Reinforced cement concrete 1:1.5:3mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum

Plastering with cement mortar 1:4 mix to 20 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Plastering with cement mortar 1:5 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Provision for electrification

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3 mm thick Hylum sheet cover with TW box And 5 A FT switch with continuous earth connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed Light point / fan point (For electronic Regulator) SD 24

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 mm X 100 mm X 113 mm TW switch box with 3 mm thick Hylum sheet cover for 5 A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for concealed PVC plug point SD 37

Supply and run of 2 of 1.50 sq.mm (22/0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade on 7/20GI bearer wire for service connection mains SD 64

Supply and run of 2 X 4 sq.mm (56 / 0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade in 25 mm dia GI pipe ( Class ' B ' ) suitably bent at both ends with necessary angle iron upright and end supports for mains. SD 70

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1"x1/8"copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW reepersof1" thick an either side with painting with suitable bolt and nuts for fixing theTWplank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Lower End) with suitable necessary connectio SD125

Supply and fixing of 1200 mm ( 48") AC ceiling fan complete with stepped electronic 300 W regulator with 300 mm down rod on the existing clamp. SD 112

Supply and fixing for 9W LED BULB SD 79

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Lower End (SD 506)

Supply and fixing for Arial Fuse Unit SD 130

Construction New Combined house (4-Nos) at Srilankan Tamil Refugees Camp in Mettupatty H/O Mettupatty (Unit-23)

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,-

Cement concrete 1:4:8 (one of cement five of sand and ten of aggregate) using 40mm size hard broken granite stone jelly for flooring including well rammed and rendering the top surface rough to receive the floor finish, curing etc. complete complying with standard specifications. The rate is inclusive of necessary planking for panelling into bays wherever necessary and as directed by the departmental officers.

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Below Basement

Basement to Lintel

Litel to Roof

Supplying and erecting, centering for sides and soffits including necessary supports and strutting up to 3.30m height for the following surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size.90cm.x 60cm and 10 B.G stiffened with mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak (country wood) joists of size 10cm x 6.5cm. spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centres complete complying with standard specification (The payment for centering shall be given after the concrete is laid.) The retrieved materials should be taken back by the contractor.

upto Basement

Lintel and Sunshade

Roof Slab

Reinforcement Cement Concrete 1:1.5:3 using 20 mm ISS HBG metal for all RCC item of works excluding cost of reinforcement and fabricating charges, centering and shuttering but icluding curing and providing fixtures like fan clamps in the RCC floor or roof vibrators, finishing, curing etc. complete and also fixing fixtures like fan clamps in the RCC floor / roof slab wherever necessary and the bearing surfaces of walls, beams shall be plastered with cement mortar 1:3 (one cement and three sand) and kraft paper laid etc.complete complying with standard specifications and as directed by the departmental officers.

upto Basement

Lintel and Sunshade

Roof Slab

Supplying, fabricating and placing in position of mild steel or ribbed tor steel grills for all RCC works as per the design given including cost of steel and binding wire in all floors etc.complete complying with standard specifications. The contractor ha

Plastering the surface of walls with cement mortar 1:5 (one of cement and six of sand) 12mm thick in all floors Finishing smooth, scaffolding, curing etc., complete complying with standard specification as directed by the departmental officers.

Supply and applying of two coats of putty of 3mm tk over the exposed RCC surface thorougly cleaned out of dust and scrubbing as per specifications etc complete.,

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing 25 mm thickness of Granolithic pattern for floor finish with cement concrete 1:2:4 (One of Cement, two of sand and four of hard broken stone jelly) using 10 to 12 mm HBG stone jelly on top surface shall be rubbed smooth finishing and curing etc., complete as per the instruction of departmental officer.

Supply and Delivery Fabrication of MS doors with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete. (Refer TWAD Page No 94)

Steel Door (0.90x2.10m) (Refer TWAD Page No 94, WD-M1485)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supply and Delivery Fabrication of MS windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete.

Steel Windows 0.90mX1.20m (Refer TWAD Page No 94, WD-M1487)

Steel Windows 0.90mX0.60m (Refer TWAD Page No 94, WD-M1488)

Painting the newly plastered wall surfaces with two coats of white washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Painting the newly plastered wall surfaces with two coats of colour washing of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Supplying and painting two coats new iron work such as steel doors ventilators, window bars etc., (WITHOUT PRIMER)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Labour charges for fixing of doors including all charges etc. ( Refer SOR Page No-35, W-0152 )

Labour charges for fixing of Windows including all charges etc. ( Refer SOR Page No-35, W-0153 )

Provision for Cudappa Slab for Shelf 0.90 x 0.30 x 0.025 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Provision for Cudappa Slab for Shelf 1.77 x 0.60 x 0.040 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position

Providing rain water harvesting structure including earthwork excavation and filling with brick jally , 40mm jally and sand including cost of material and all labour charges.

Towards supply and delivery of RCC Jolly (20 cm x 20 cm) including cost and conveyance of materails and all labour charges for fixing in position as per std. Specification

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supply and fixing of 110 mm dia pvc pipe for chamber connection

Provision for Septic Tank (2-Nos)

Earthwork excavation in all soils & subsoils includibng all charges etc.,

Earth work excavation for foundation in hard rock requiring blasting & Stacking

Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier etc

Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all R.C.C works with standard specification etc complete.

Reinforced cement concrete 1:1.5:3mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum

Plastering with cement mortar 1:4 mix to 20 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Plastering with cement mortar 1:5 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Provision for electrification

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3 mm thick Hylum sheet cover with TW box And 5 A FT switch with continuous earth connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed Light point / fan point (For electronic Regulator) SD 24

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 mm X 100 mm X 113 mm TW switch box with 3 mm thick Hylum sheet cover for 5 A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for concealed PVC plug point SD 37

Supply and run of 2 of 1.50 sq.mm (22/0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade on 7/20GI bearer wire for service connection mains SD 64

Supply and run of 2 X 4 sq.mm (56 / 0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade in 25 mm dia GI pipe ( Class ' B ' ) suitably bent at both ends with necessary angle iron upright and end supports for mains. SD 70

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1"x1/8"copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW reepersof1" thick an either side with painting with suitable bolt and nuts for fixing theTWplank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Lower End) with suitable necessary connectio SD125

Supply and fixing of 1200 mm ( 48") AC ceiling fan complete with stepped electronic 300 W regulator with 300 mm down rod on the existing clamp. SD 112

Supply and fixing for 9W LED BULB SD 79

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Lower End (SD 506)

Supply and fixing for Arial Fuse Unit SD 130

GST Amount for providing Service to Government Contract Works for the above RENEWAL Works. { GST Amount is the Total GST Amount for overall quoted amount above this row in column "BB" for all works in this package} (Refer Clause 13.2 & 13.3 of Section 2 of Instruction to Bidders (ITB) of SBD)

SRI BHANNARI AMMAN BUILDERS (BID ID -1371727)