REPAIR TO SECURITY FENCING WALL PERIMETER WALL AND ALLIED WORKS AT VARIOUS LOCATIONS UNDER AGE B R I OF GE AF ADM AREA KHERIA AGRA

Amount

Taking down chain link fencing including line wires, of any mesh size and type of standard rails, straining bolts etc. complete all as specified and directed.

Dismantling of posts or struts (Steel/ RCC) any section including taking out embedded portion in concrete or brick work or masonry portion & making good disturbed ground complete all as specified and directed.

Dismantling of structural steel work including door, gates, grill or any description complete all as specified and directed.

S&F in repair galvanised two strand steel barbed wire 2.24mm dia, barbed with 2 mm dia barbs at 75 mm spacing & straining & fixing to any type of standard rails straining bolts including securing or tying at crossing with & provision of galvanised mild steel wire staples or steel pins complete all as specified and directed.

All as per item No 4.00 here-in-before but fixing only in repairs.

M&L for PCC 1:3:6 Type C-2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

S&F mild steel posts & struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc. fillets for securing wire mesh etc including necessary drilling bolting riveting etc. & similar work, fence complete conforming to Fe- 410 - or Fe-310-0 complete all as specified and directed.

All as per item No 7.00 here-in-before but fixing only.

S&F for mild steel flat iron of size 40 x 6 mm for securing wire mesh as in fencing post including necessary drilling holes completes conforming to Fe. 410-0 or Fe. 310-0 all as specified and directed.

S&F for mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, of suitable length & dia for fixing of the flat iron in fencing post complete all as specified and directed.

S&F chain link MS galvanised fencing of 4 mm dia of wire & aperture 75 mm x 75 mm including line wires straining bolts etc. rails & binding wire complete all as specified and directed.

All as per item No 11.00 here-in-before but except chain link fencing of any mesh size and type.

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping, hooking ends and binding with ms wire (annealed not less than 0.9 mm dia and fixed to angle iron posts including welding and woven through chain link fencing etc complete all as specified and directed.

S&F in repair MS framed work for grills, railings, gratings, etc. with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard square bars, MS plates to framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for taking down MS doors shutters and refixing same by necessary jointing/ welding, straighten the MS member incl MS hold fast and with PCC block and providing two coats of synthetic enemal paint, size of MS shutter exc 1.00 Sqm and n. exc 2.50 Sqm complete all as specified and directed.

M&L for brick work with old size, sub-class `B' bricks in full brick thick walls, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 including demolition of old/ existing brick work complete all as specified and directed.

All as per item No 16.00 here-in-before but except bricks.

M&L for rendering 15 mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished surfaces even and fair complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 on other than fair faces of brick work or concrete surfaces finished surfaces even and fair complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint complete all as specified and directed.

M&L for preparation of new steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L in repair for 60 mm thick machine pressed rubber moulded precast concrete M-30 interlocking coloured paver block any shape and size conforming to IS-15658-2006 laid over and including 25 mm sand cushion and filling joints complete all as specified and directed.

Demolition of precast cement concrete articles such as RCC jalli etc set in cement mortar or cement lime mortar complete all as specified and directed.

S&F precast RCC louvers, jallies 40 mm thick Type B-0, 1:2:4 (using 12.5 mm graded stone aggregate) including all mouldings and frame work set in CM (1:4) complete all as specified and directed.

M&L for 18 to 20 mm thick granite (any type) work (table rubbed and polished) as in skirting, dado, steps, pillars, jambs, cooking platform, window cills and like in cement mortar 1:4 including pointed with white cement (1:2) using marble dust with admixture of pigment to match the shade of granite stone over screed bed 15 mm thick in cement mortar 1 : 4 including dismantling old granite complete all as specified and directed.

Demolition of cement concrete ( reinforced) of any description in any position not otherwise specially provide for complete all as specified and directed.

M&L for reinforced cement concrete type A-1 (1:1.5 :3) (using 20 mm graded stone aggregate) as in foundations, inlcuding rafts, footing, foundation beams, plinth beams bases for columns etc basement slabs under reamed piles and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete 1:1.5:3 type A-1 (using 20 mm graded stone aggregate) as in columns, pillars, etc complete all as specified and directed.

M&L for formwork to sides of pillars, post, structs, piers foundation, columns and stanchions etc with rough finished square or rectangular complete all as specified and directed.

M&L for mild steel TMT bar 10 mm dia and over cut to length, bent to shape reqd, incl cranking, bending, spirally for hooping, hooking ends and binding with 0.90 mm dia MS wire (annealed) not less than 0.9mm dia or securing with clips etc complete all as specified and directed.

S&F Mild steel TMT bars 8 mm dia , cut to length and bent to shape as reqd, including cranking , bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed ) not less than 0.90 mm dia complete all as specified and directed .

M&L for formwork to soffit and sides of suspended slab, slab supported on walls, columns, beams and similar work not exceeding 200 mm thick (Horizontal or sloping) , rough finished surface of concrete all as specified and directed.

M&L for RCC 1:1.5:3, Type A-1, (using 20 mm graded stone aggregate) in slab supported on walls , beams, columns and similar work etc . complete all as specified and directed.

S&F in repair concertina coil of 600 mm dia (in stretched position), not dip galvanised steel wire coated with CLR anti corrosive paint, making diamond shape with the help of dove tail clips (18 SWG), fixed to the MS angle iron/ precast RCC fencing post to be fixed with barbed wire at points where coil touched the bottom with the help of lug rings (24 SWG) complete all as specified and directed.

All as per item No 34.00 here-in-before but except concertina coil.

S&F in repair concertina coil of 900 mm dia (in stretched position), not dip galvanised steel wire coated with CLR anti corrosive paint, making diamond shape with the help of dove tail clips (18 SWG), fixed to the MS angle iron/ precast RCC fencing post to be fixed with barbed wire at points where coil touched the bottom with the help of lug rings (24 SWG) complete all as specified and directed.

All as per item No 36.00 here-in-before but except concertina coil.

S&F in repair galvanised 2 strand, steel razor sharp wire spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossings with and provision of galvanised mild steel, wire, staples or steel pins, etc complete all as specified and directed.(Note - Each line of wire to be measured).

M&L for washed stone grit plaster on exterior walls in two layers, under layer 12 mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square meter, top layer 15 mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings including taking down old girth finish and cleaning/ prepration of surface complete all as specified and directed. Note : Making grooves(of uniform size 15 mm x 15 mm) shall be included in quoted rates.

M&L for 25 mm thick rough dressed sand stone slab as in vertical surfaces, set, jointed and pointed in cement mortar 1:3 over & including 10mm thick rendering in CM (1:3) including taking down complete all as specified and directed.

Demolition cement concrete (un reinforced) of any description in ground floor n. exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for plain cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete all as specified and directed.

M&L for cement concrete type B-0,1:2:4 ( using 12.50 mm graded stone aggregate) as in coping etc including necessary formwork complete all as specified and directed.

M&L for apply 2mm thick thermo plastic road marking compound of white/yellow (approved colours) colour & shade for road marking with machine on bituminous/concrete road surface width or paint line as per direction of Engr-in-Charge at site & managing the traffic control with proper arrangement etc complete all as specified and directed. Make : ASIAN MOST CMS APCO-BS or approved by GE

M&L for coloured vitrified tiles of 8 to 10 mm thick first quality (square / rectangular) polished, area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm as in floor etc set and jointed in neat cement slurry and pointed with coloured cement to match the colour of tiles over and including 15 mm thick screed bed in CM 1:4 and dismantling of old tiles complete all as specified and directed.

All as per item No 45.00 here-in-before but in dado/ skirting over and including 15 mm thick rendering in CM 1:3.

M&L for coloured glazed ceramic tiles first quality of size 400 mm x 400 mm, 7 mm thick, set & jointed in neat cement slurry and pointed with coloured cement to match with tiles in floosr etc over and including 15 mm thick screed bed in cement mortar 1:4 including dismantiling of old tiles complete all as specified and directed.

All as per item No 47.00 here-in-before but in dado/ skirting over and including 15 mm thick rendering in CM 1:3.

M&L of glazed ceramic coloured tiles in vertical surface of size 450 mm x 300 mm x 7 mm thick set & jointed in neat cement slurry and pointed with coloured cement to match with tiles over and including 15 mm thick rendering in cement mortar 1:3 including dismantiling of old tiles complete all as specified and directed.

S&F in repairs colour cat eyes/road studs size (mm) 100 x 110 x 20 having tough poly carbonite micro reflected corned cube reflector tenses with a protective abrasion resistant ceramor coating having body of weather proof and impact resistant thermoplastic fixed on road for roadways sign complete all as specified and as per manufacturers instructions and directed. MAKE- Dark Eye model No DA-52 with double shank, 3M or equivalent as approved by GE. .

S&F in repair ABS plastic speed bumb/speed breaker in parabolic convex shape and of size 750 mm x 250 mm x 75 mm made out of stardy plastic highly resistance to sever impacts and harsh weather condition, dovetail interlocking sub units, jointed and fixed to make the bub perfectly uniform bump made out of precoloured material (black/yellow) and UV stablizers to keep them perfectly colourful, studded with reflectors on either side to make it clearly visible to motorists during night hours complete all as specified and directed. Make: Dark eye India Pvt Ltd Model No DA 1006/ 3M or equivalent or as approved by GE.

M&L for 16 to 18 mm thick polished red stone (any type) work (table rounded and polished) as in skirting, dado, steps, pillars, jambs, in fixed cement mortar 1:4 including pointed with white cement (1 :2) using marble dust with admixture of pigment to match the shade of stone over & including 15mm thick screed bed in cement mortar 1:4 with and including fixing of SS clamp/fastening including taking down of existing red stone including cement plaster complete all as specified and directed.

M&L for complete removal of existing treatment from external surfaces of walls by wire brushing and washing rubbing down and stopping of surfaces and leveling/edging the disturbed place/edge and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L for complete removal of existing treatment from external surfaces of walls by wire brushing and washing rubbing down and stopping of surfaces and leveling/edging the disturbed place/edge using necessary filling compound of altek putty to obtain smooth regular/even finish using sand paper and applying two coats of exterior emulsion paint over a coat of primer and 1 mm thick putty complete all as specified and directed.

M&L for complete removal of existing treatment on old painted plastered or concrete surfaces and applying two coats of synthetic enamel paint on kerb stone in alternative colour complete all as specified and directed.

M&L for rendering 15 mm thick on fair face of brick works or concrete surfaces of walls with CM (1:6) and finished even and smooth without using extra cement including taking down of old cement plaster of any description complete all as specified and directed.

M&L for prepration of newly plastered surface of walls and applying two coats of exterior emulsion paint over a coat of primer and 1 mm thick putty complete all as specified and directed.

M&L for 100 mm thick moorum/ red bajri filling under berms spread, levelled to gradient and camber as required complete all as specified and directed.

M&L for rubber moulded chequered cement concrete tiles 30cmx30cmx25mm thick, set, jointed and pointed in neat cement slurry in floors including screed bed or bedding layer of cement mortar 1:6, 15 mm thick for laying floor finishes including dismantling of old tiles with bedding complete all as specified and directed.

M&L for 40 mm thick cement concrete type B1, 1:2:4 (20 mm graded stone aggregate) as in floor, finished the surface even and smooth with using extra cement laid in panels including provn of 3 mm thick 38 mm wide glass strips and demolition of old PCC floor complete all as specified and directed.

M&L for preparation of old painted concrete/ cement plastered surfaces and applying one coat of synthetic enamel paint in alternative coloures complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C1 (using 20mm graded stone aggregate) as in plinth protection/ paving, finished surface even and fair including demolition of old PCC complete all as specifie and directed.

M&L for prepration of old painted surfaces of walls and appying one coat cement base paint all as specified and directed.

M/s K S Builders

GIRENDRA SINGH AND CO

M/s M S Sharma and Co.

deva engineers

Asha Construction

SHRI SAINATH ENGINEERS