SPECIAL REPAIR TO ROOF TREATMENT OF DUNGEONS AT INS ANGRE, SPECIAL REPAIRS TO ROOF WITH WATER PROOFING TREATMENT OF BLDG NO P-198 SYSTEM DEPARTMENT ND MBI AND PROVISION OF CERTAIN MINOR WORKS AT ND MBI UNDER GE (NW) KUNJALI, COLABA, MUMBAI

Amount

Taking down cement or cement lime plaster, any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc including all necessary scaffolding as required and rubbishing off the premises etc complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for rendering 15mm thick in CM 1:4 on brick surfaces, finished even and smooth (without using extra cement) complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for rendering 15mm thick in CM 1:4 on brick surfaces, finished even and smooth (without using extra cement) mixed with integral water proofing compond in the proportion as mentioned in manufacturer's instructions (WPC shall be measured and paid seperately) complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for Plastering 15mm thick in CM 1:6 on brick surfaces,finished with Neeru finish on walls complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth (without using extra cement) including Sagol finish complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for rendering 20 mm thick pre polymer modified ready mixed cement based plaster in two coats 12 mm thick base coat and 8 mm thick finishing/final coat. Polymer modified ready mixed cement based plaster should having minimum composition of cement and sand 1:4 using fully treated dry, well graded natural sand confirming to IS-383 suitable for external plastering having low rebound properties, low water demand for curing properties , mechnical mixing with water in a metallic tray only to made good, consistency as per the specification of the manufacturer and applied over exterior masonry and concrete surfaces incl using richer mix for making corners if necessary incl making grooves of existing size and necessary two legged MS pipe scaffolding as wherever required incl curing required in high rise building complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for Plastering 5mm thick in CM 1:3 on concete surfaces as in ceiling finished even & smooth without using extra cement in ceiling. complete all as specified and as directed by Engineer-in-Charge.

Supply only integral water proofing compound. complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for machine pressed chequered cement coloured tiles of size 250mmx250mmx20mm/ 300mm x 300mm x 20 mm thick mix with grey cement and pigment laid over 15mm thick screed bed in CM 1:3 set and jointed and pointedin neat cement slurry in floors complete all as specified and as directed by Engineer-in-Charge.

Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for roughening surfaces of old concrete surfaces by picking, sweeping cleaning and washing down with water to remove dust etc including taking down tarfelt and 15 mm thick screeding in cement mortar 1:4 finished even and smooth without using extra cement including mixed with water proofing compound as per manufacturer instructions (WPC shall be measured and paid separately). complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for PCC 1:2:4 type B-0 (using 12.50 mm graded crushed stone aggregate) cement concrete as a leveling course on roof surfaces and coping etc complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in roof/ chajja slope complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for applying a coat of bituminous primer 0.25 Kg/Sqm on prepared surface of plaster as per manufacturer's instructions, manufactured by the same agency of APP membrane. After applying of bituminous primer applying evenly a coat of bitumen 85/25 at the rate of 1.2 kg per sqm incl cleaning surfaces. Providing and laying five layered 4 mm thick APP (Atatic poly propylele) modified polyester reinforced water proofing membrane with minimum weight of 4.60 Kg/Sqm, as specified here-in-after. The APP membrane shall be laid using torch on application with minimum 100 mm side overlap and 150 mm end overlap. The laying of membrane shall be got done through an authorised applicator of manufacturer of the membrane. The APP membrane shall be taken upto minimum 200 mm on vertial surfaces. The edge of the membrane shall be sealed with sealant. The rain water gutter portion shall be finished with cement mortar 1:4 to provide requisite slope towards rain water pipe outlet . over the APP membrane provide a polypropylene/polyester, non woven geotextile fabric of 150 gram/Sqm complete all as specified and directed by Engr-in - charge Notes :- (i) Irrespective of lap the net covered area shall only be measured and paid (ii) The quoted rate shall be deemed to be inclusive of bituminous primer and a coat of bitumen 85/25 at the rate of 1.2 Kg per Sqm for APP membrane complete all as specified and directed by Engineer-in-Charge.

Material & Labour for applying oil bound primer at 0.40 litre/ Sqm manufactured by the same agency as that of APP with density of 0.87 to 0.89 kg/litre at 25 degree celcius on the prepared dry roof surface and provide and lay 4mm thick APP modified water proofing membrane reinforced with non woven polyester mat with physical properties as given in particular specification. The laying shall be done through authorized applicator of manufacturer as specified in particular specification. Providing over the membrane finishing with two coats of solar reflective bituminous aluminium paint @ 0.10 kg/Sqm as prescribed by manufacturer of membrane etc complete all as particular specification, manufacturer's instructions and as directed by Engr-in-charge Notes :-Rate inclusive of taking down and refixing of existing lightning arrestor system including provision of new PCC block for damaged PCC block complete all as specified and directed by the Engr-in- charge

Material & Labour for brushing neat cement slurry with 3Kg of cement per square metre complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for rendering 20 mm thick cement plaster in CM (1:3) on roof top surface finished even and fair including WPC by weight of 3% of total cement content complete all as specified and as directed by Engineer-in-Charge. Note : WPC will be measured and paid separately

Material & Labour for coloured endura terrace tiles of size 300mmx300mmx10mm thick laid over 20mm thick screed bed in CM 1:4 set and jointed and pointed in neat cement slurry complete all as specified and as directed by Engineer-in-Charge.

Taking down chowkats or frames but n exc 1.5 sqm each but with shutters (without taking off shutters from the frame) complete all as specified and as directed by Engineer-in-Charge.

Taking down chowkats or frames exc 1.5 sqm n exc 4 sqm each but with shutters (without taking off shutters from the frame) complete all as specified and as directed by Engineer-in-Charge.

Taking down shutters of any description exc 1 sqm and n exc 2 sq.m each complete all as specified and as directed by Engineer-in-Charge.

Taking down shutters of any description n.exc 1.00 Sqm each complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing 2nd class hard wood (sal) plain, solid, straight chowkhats and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing 35mm thick factory made 2nd class HW rail & stile plain framed , panelled shutter ( two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003( Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing 30mm thick 2nd class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc. divided in to squares,with plain, chamfered or rounded , mitred and rebated sash bars,any numbers ; edges of framing plain, chamfered or rounded , fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8 clause 8.24 (a) ; supplied and fitted to chowkhats of Second class hard wood. complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing 40mm thick flush shutters, solid core construction, with block board core and ply wood face panels, commercial type on both side. complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing in repair powder coated aluminium (minimum 25 micron thickness of coating) of various section as required for doors, window & partition/Ventilator etc including fixing and making the frames hinges to receive glass/wire gauge etc. Complete incl all fittings like rubber beading, clips locking arrangement, handle, tower bolt for shutter, sealant etc complete all as specified and directed by Engr- in- charge.

Supply & Fixing in repair aluminium grill with and including suitable aluminium anodised frame F/H section as required manufactured by M/s. Decogrill as per design No DG- 102, 7.50 mm thick all as complete all as specified and directed by Engr- in- charge.

Supply & Fixing Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel stapple etc. complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing in repairs 18/19 mm thick prelaminated particle board exterior grade prelaminated one side with lamination and other side balancing white lamination fixed with screw to frame work cupboard etc including 6 mm thick teak wood beading all around complete all as specified and as directed by Engineer-in-Charge.

Ditto all as per item no 31.00 above but 9mm thick pre laminated particle board fixed in repairs complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing 12mm thick prelaminated medium density fibre board,interior grade, prelaminated both sides with decorative choice lamination fixed with screws to aluminium frame work complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing 300 mm long aluminium alloy, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts . complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing for aluminium anodized barrel tower bolts 200 mm of extruded section and fixed. complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing for aluminium anodized barrel tower bolts 150 mm of extruded section and fixed. complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing 150 mm size aluminium alloy handles, febricated type extruded section, ISI marked complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing Butt hinges 100 mm mild steel hinges medium weight and fixed. complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing Butt hinges 75 mm mild steel hinges medium weight and fixed. complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for MS flat for hold fast. Conforming to Fe-290-0 or Fe-165 complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing in repairs 125 mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring complete all as specified and as directed by Engineer-in-Charge.

Complete removal of existing water proofing treatment of any description in any position including roof tiles,PCC.brick bat coba,upto any thickness cleaning, wire brushing, watering and removing of debris upto 15km or further distance complete all as specified and as directed by Engineer-in-charge

Material & Labour for chipping, removing carefully concrete work by low impact hammer breakar without damaging the structure & cleaning and disposal of debris out side the premises etc complete as directed by Engr-in-Charge, hard concrete should not be removed by force including necessary scaffolding for high rise bldgs etc complete all as specified and as directed by Engineer-in-charge

Material & Labour for cleaning existing reinforcement with wire/rotary wire brush, making the surfaces free from loose material dirt etc complete applying two coats of alkaline rust converting primer FEOVERT confirming to ASTM-B-117, on the rebars, including cleaning the reinforcement wire brush to removing loose rust spalls with time interval of 6 hour between the coats and applying protective coating IPNET-RB complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for replacement of steel reinforcement with TMT bars of appropriate size where 20% of cross section is reduced including dismantling of rusted steel including application of rust converter FEOVERT and applying protective coating IPNET-RB complete all as specified and as directed by Engineer-in-Charge.

Material & Labour to carry out application of Bi-polar migratory corrosion inhibitor EPCO-KP-100/Protectsil CIT/Ferogard 903 on concrete surface (This inhibitor shall have migratory kind of properly which permits the material to migrate to a vertual extent of 100 mm through pores of concrete, inhibiting the corrosion and de-passivating the Electro-chemical reaction. It should have properly to attack anode as well as cathode, which is purely alkaline in nature (pH-9.5) so it has not carcinogen activity with concrete. complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for providing and applying structural grade EPIBOND-21-LP prior to application of any type of mortar plaster confirming to ASTM-C-882-91 (Arizona Slant Shear Test) to ensure bond between old concrete and new concrete.complete all as specified and as directed by EIC.

Material & Labour for Building up the profile of structural members by using latex additives (MONOBOND) modified air cured mortar system (Polymer modified mortar) (1:5:15 = 1 Monobond-5 Cement-15 sand) -in damaged areas in 30mm thickness including leveling profliling and scaffolding for high rise buildings etc complete all as specified and as directed by EIC.

Material & Labour for Providing and applying jacketing around columns/RCC members with Micro concrete (Molith-MC) M40 including all lifts, shuttering, drilling holes and fixing shear anchor as per specification complete.Note: Reinforcement shall be measured and paid separately.(Rates including jacketing, formwork and micro concrete) complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for Drilling and fixing Rohibb Teflon nozzles in RCC members, including drilling holes of 12mm dia, 50 to 100mm deep holes in structural members at the intervals of 500 center to center in staggered manner or complete all as specied and directed by Engr-in-charge in RCC structural element. Work shall be carried out as under :- (i) Cleaning of holes. Cleaning the holes by air blower prior to fixing nozzles.(ii) Fixing of nozzles. Insert 12mm dia. Rohibb Teflon nozzles in cleaned holes. External end of nozzles to be made to receive outlet of grouting gun.Fixing it inside the holes by applying thixotropic epoxy putty to ensure complete sealing. Curing the system for min.12 hrs. (iii) Cutting of nozzles. Cutting the nozzles by chisel after completion of grouting without damaging structural elements. complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for Injecting of site cement slurry grout, in the ratio 1:2 (1- Cement, 2- Water) including super plasticizer (Supercom-100) 250 ml/50 Kgs. Mixing shall be done by mechanical mixer continuously stirring mechanically to keep cement particles in suspension. Injection of approved/specified grout by means of pump at a pressure of 0.5 Kg/cm2 etc complete till the grout mix flows out from the nozzle indicating complete filling of grout in the holes drilled. (for repair to wall & slab) complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for Injecting low Viscosity MONOPOL (3-5cps) high molecular weight monomer by pressure and using mechanized injector gun with accessories till nozzles refuses to accept the grout, Including,Mixing of materials:Mixing of material components(part a&b) in the required quantities as per manufacturer's instruction by weigh batching.Grouting maintain the pressureat exit(0.5 to 1.0 kg/cm2) by monitoring pressure guage at exit. Grouting the material through prefixed nozzles in the structural elements@ 100ml per nozzle. The process for all the nozzles shall be repeated (Beam and columns) complete all as specified and as directed by Engineer-in-Charge.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles and disposing off complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for brick work with sub class B bricks straight or curved on plan exceeding 6 m mean radius built in CM 1:6 complete all as specified and as directed by Engineer-in-Charge.

Ditto all as per item No 54.00 above but except bricks

Material & Labour for brick work with sub class 'B' bricks straight or curved on plans to any radius in half brick thick walls built in cm (1:4) complete all as specified and as directed by Engineer-in-Charge.

Material & Labour stone walling of random rubble, uncoursed brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge.

Ditto all as per item No 57.00 above but except stone

Material & Labour for flush pointing in CM 1:3 to random rubble masonry, uncoursed or brought upto courses complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc as specified erected in position and securing runners with holdfasts and brackets complete all as specified and as directed by Engineer-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for all. complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; walk ways, railings, frame work for water tanks and similar work conforming to Fe 290 Gd E-165. complete all as specified and as directed by Engineer-in-Charge.

Material and labour for providing plain cement concrete type B-1, 1:2:4 (using 20 mm graded crushed stone agg) as in lintels upto 1.5 M clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60 cm in height, copings, kneelers, apex stones, bed plates, roof kerbs, water troughs and the like including weathering slightly rounded or chamfered angles and throating complete all as specified and as directed by Engineer-in-Charge.

M& L for steel form work & props to sides of concrete foundations, footings, bases of columns , raft and raft beams, sides and soffits ( if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing Mild steel TMT Bars epoxy coated 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending sprially for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed) not less than 0.90 mm dia, or securing with clips complete all as specified and as directed by Engineer-in-Charge.

Returning, filling in, including spreading, levelling , watering and well ramming in layers not exc 25 cm in hard/ dense soil complete all as specified and as directed by Engineer-in-Charge.

Removing excavated material (Rocks) n exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point out side the MoD Land complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Hard wear stone (of any type) granite stone slab 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types and including 15mm thick screed bed in CM 1:4 complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and as directed by Engineer-in-Charge.

Material & Labour brick work with sub class 'B' bricks old size, straight or curved on plan exc 6m mean radius in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for Non skid heritage type coloured ceramic tiles of 12mm thick ( square/ rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors/ wall/ vertical surface etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of the tiles with and including 15mm thick screed bed in CM 1:4 complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for Coloured glazed ceramic tiles in vertical surface 350 x 250 x 7mm/ 450X350X7mm thick with and including 10 mm thick cm (1:4) backing coat and Triangular filleting at top of skirting, set and jointed in neat cement paste and pointed in coloured cement to match the shade of the tiles complete all as specified and as directed by Engineer-in-Charge.

Dismantling stone slab and tiles of of any description or thickness laid bedded and pointed in any mortar in floors, aprons etc complete all as specified and as directed by Engineer-in-Charge.

Material & Labour 20 mm thick Granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window- cills,cooking platforms, working table and like over 20 mm thick screed bed or bedding layer in cement mortar (1:4), including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for machine cut kota stone slab flooring 18 to 20 mm thick as in steps, landings, floors etc laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing,mirror polishing incl making 02 Nos grooves in steps over & incl 20 mm thick screed bed in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for machine cut kota stone slab 18 to 20 mm thick as in skirting/vertical surfaces jointed and pointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing and 15 mm thick backing coat in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge.

Rounding to edges of stone slabs on edge, such as in steps, cooking platform and making grooves for lining and other similar work complete all as specified and as directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and disposing the rubbish to the out side of MoD land complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for Coloured glazed ceramic tiles in vertical surface 450X300X10 / 600 X 300 X 10 mm thick, set and jointed in neat cement paste and pointed in coloured cement to match the shade of the tiles with and including 10 mm thick backing coat in CM 1:3 complete all as specified and as directed by Engineer-in-Charge.

Dismantling posts or struts (wood, steel or R.C.C.) any section, post embedded in cement mortar, brick work, masonry etc. including taking out embedded portion and making good disturbed ground complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing mild steel works as in posts and struts on roof and in fencing including cutting tops to shape as directed, drilling holes, base plate,notching for wire etc flat iron fillets (for securing wire mesh etc) including all necessary drilling bolting or riveting etc and similar works conforming to FE- 290 (Gde E-165) complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for PCC 1:2:4 type B-1, (using 20mm graded crushed stone aggregate) as in grouting of angle posts, pillars etc including necessary form work complete all as specified and as directed by Engineer-in-Charge.

Dismantling cast iron or reinforced concrete drain pipes of dia upto 100 mm jointed in cement mortar fixed to wall of high rise buildings or taking out from trenches as required. complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing 100 mm bore Cast iron soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls with MS clamps complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing 75 mm bore Cast iron soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls with MS clamps complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing in repairs CI Bends100 mm bore (any radius), diminishing pieces or tapers ( larger bore measured) complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing in repairs CI Bends 75 mm bore ( any radius), diminishing pieces or tapers ( larger bore measured) complete all as specified and as directed by Engineer-in-Charge.

Material & Labour in repairs Cast iron nahani trap with grating including jointing to waste pipe run lead 100 mm complete all as specified and as directed by Engineer-in-Charge.

Taking down PVC waste and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing 160mm dia bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls with ms clamps complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing 160mm dia bore PVC (SWR) bends any radius complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing 110 mm bore PVC (SWR) bends any radius complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing 75 mm bore PVC (SWR) bends any radius complete all as specified and as directed by Engineer-in-Charge.

Taking up or down 15mm bore steel tubing connection including cleaning for refixing or removing etc complete.

-Ditto- all as per srl item No. 99.00 above but 20mm dia.

-Ditto- all as per Srl item No. 99.00 above but 25mm

Supply, laying, connecting and testing GI Tubing, medium grade with all fittings and fixed complete to wall and ceiling or laid in floor complete all as specified and as directed by Engineer-in-Charge. for following sizes:-

15mm dia

20mm dia

25mm dia

Supply & Fixing in gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe & fixed in repairs for 20mm bore complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing in gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe & fixed in repairs for 25 mm bore complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing in repairs 20mm bore Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of of primer complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for preparation of newly plastered surfaces of ceiling and applying two coat of oil emulsion distemper over a coat of primer complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for preparation of old painted steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying one coat of synthetic enamel paint with necessary scaffolding for high rise bldgs etc complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for preparation of new steel surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and as directed by Engineer-in-Charge.

Complete removal of existing treatment on ceiling surfaces and applying two coats of oil emulsion distemper over a coat of primer on ceiling surfaces incl preparation of surfaces complete all as specified and as directed by Engineer-in-Charge.

Complete removal of existing treatment on wall surfaces by scrapping, washing & rubbing down with water and applying two coats of oil bound distemper over a coat Chalk whiting, onplastered surfaces, complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for preparation of old decorated surfaces of wall and applying one coat of oil emulsion distemper complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for applying 1 to 2 mm thick wall care putty (JK/Birla) for making the surface even & smooth all as specified and directed by the Engineer-in-Charge.

Material & Labour for preparation of old decorated surfaces of ceiling and applying one coat of oil emulsion distemper complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for preparation of newly plastered surfaces of wall, soffits, facia roof and applying two coats of weather proof acrylic based paint (100% acrylic) over one coat of cement based primer with necessary scaffolding for high rise blds etc complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for preparing new plastered surfaces of walls and applying two coats of oil bound distemper with priming plastered and other surfaces with alkali resistant primer with 3mm thk wall care putty on plastered surfaces complete all as specified and as directed by Engineer-in-Charge.

Material & Labour preparation of new plastered surface of ceiling and applying three coat of white wash on ceiling complete all as specified and as directed by Engineer-in-Charge.

Surface excavation n. exc 30cm depth and averaging 15cm deep and getting out in soft/loose soil complete all as specified and as directed by Engineer-in-Charge.

Excavating over areas, n exc 1.5 m deep and getting out in hard/ dense soil complete all as specified and as directed by Engineer-in-Charge.

Material & Labour hardcore of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to true surfaces (broken stone or boulders) complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for PCC 1:3:6 type C-2 ( 40 mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for RCC (design mix), M-30 in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under reamed piles and mass concrete complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for 150 mm spread thick soling with broken boulders or quarried stone, interstices filled , surface formed and rolled and consolidated to required gradient and camber complete all as specified and as directed by Engineer-in-Charge.

Rolling to Soling of broken boulder or quarried stone n.exc. 15 cm thickness using 8 to 10 ton Power roller complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for polythene film ,black ,50 micron laid in floors complete all as specified and as directed by Engineer-in-Charge.

Material & Labour PCC (1:4:8) D-2 40mm graded crushed stone aggregate in sub base 150 mm thick complete all as specified and as directed by Engineer-in-Charge.

Material & Labour PCC 1:11/2 :3, type B 1 100 mm thick in floors complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for forming Construction (Dummy) jionts 65 mm deep x 10 mm wide, filled with sealing compound joint 30 mm deepX 10 mm wide filled with sealing compound, Grade' A' complete all as specified and as directed by Engineer-in-Charge.

Material & Labour Complete removal of existing treatment of old decorated surfaces of walls soffits, facia roof and applying two coat of weather proof acrylic based paint (100% acrylic) over one coat of cement base primer with necessary scaffolding for high rise bldgs. etc complete all as specified and as directed by Engineer-in-Charge.

Material & Labour preparation of old decorated surfaces of walls, soffits, roof facia and applying one coat of weather proof acrylic based paint (100% acrylic) with necessary scaffolding for high rise bldgs etc complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for preparation of newly wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer incl preparation of surfaces. complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for preparation of old painted wooden surfaes of any description over 10cm width or girth and applying one coat of synthetic enamel paint including external window with necessary scaffolding for high rise bldgs. complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for 4 mm Bakelite sheet with decorative choice laminated on both side complete all as specified and as directed by Engineer-in-Charge.

Removing excavated material n.exc 50m and n.exc 250m and depositiing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed by Engineer-in-Charge.

Removing of bldg materials exc 5 KM but not exc15.00 KM and depositing where directed outside MoD land complete all as specified and as directed by Engineer-in-Charge.

Taking down carefully old unserviceable point wiring copper/Aluminum (light/ fan /sockets/power) complete with switches, sockets, fan regulators, ceiling roses, lamp holders, brackets, ,removing material to store for keeping in safe custody and making good to disturbed surfaces as complete all as specified and directed by Engineer-in-Charge

Material & Labour for point wiring with FRLS PVC insulated, un-sheathed, multi stranded copper conductor cable of 1.5sqmm size, 1100volts, drawn through and including non metalic rigid PVC casing and caping not less than 25mm with all accessories fixed on wall//ceiling/truss including FRLS PVC insulated, unsheathed, multi stranded copper conductor cable of 1.5sqmm size as earth continuty conductor connected to common earth dolly including required numbers and size of PVC modular box with cover plate in any size fixed on wall for fixing the switches, switch sockets,sockets, regulators etc complete all as specified and as directed by Engineer-in-Charge. NOTE: a) Colour coding shall be followed as given below:- i) Phase - Red/Blue/Yellow ii) Neutral - Black iii) Earth - Greenb) Electrical wiring above false ceiling shall be drawn through medium grade PVC conduit.

One light point controlled by one 5A switch

One Fan point controlled by one 5A switch

One 5A flush type switch socket point on same board board

One 5A flush type switch socket point on independent board

Material & Labour for point wiring complete with proper clour coding using PVC insulated unsheathed multistranded copper conductor cable 2.5 sqmm size, 1100 volts ISI marked, FRLS grade drawn through and including non metalic rigid, double lock, ISI marked, not less than 25mm casing caping with all accessories such as tee, bends, elbow, reducers, junction box etcfixed on wall/ceiling/truss and one run of PVC insulated unsheathed, multistranded copper conductor cable of 2.5sqmm size, 1100 volts, ISI marked, FRLS grade green colour as earth continuty conductor connected to common earth dolly with and including required size of PVC modular box with cover plate for One 5 pin, 15A switch socket combination on the independent board complete all as specified and directed by Engr-in- charge. Note: (a) Colour coding shall be folowed as (i) Phase- Red/Blue/Yellow (ii) Neutral - Black (iii) Earth - green (b) Switch socket measured & paid separately

Supply & Fixing ceiling rose surface bakelite 65 x 50mm, flush type, 3 terminals c complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing modular switch 1 way 6A complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing modular switch 1 way 16A,1 module complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing modular socket, 6A - 2/3 pin combined 2 modules complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing modular socket 6/16A,2/3 pin, combined 2 module complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing for modular fan step regulator, 120W - 2 modular complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing on replacement of hanger clamp assembly with down rod up to 3 feet for hanging of ceiling fan with nuts,bolts,washers & split pin complete all as specified and as directed by Engineer-in-Charge.

Disconnecting and taking down the fan and Overhauling of ceiling fan any size and make, dismantling parts, properly cleaning/removing old existing grease oil and applying new oil grease, varnishing of winding, cleaning dust, rust and applying two coats white enamel paint over a coat of steel primer, assembling and refixing at same position complete all as specified and as directed by Engineer-in-Charge.

Disconnecting and taking down the fan and Overhauling of exhaust fan any size and make, dismantling parts, properly cleaning/removing old existing grease oil and applying new oil grease, varnishing of winding, cleaning dust, rust and applying two coat grey paint over a coat of steel primer, assembling and refixing at same position complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair new generation wall/surface mounted 1x 20W LED batten fitting, 4 feet surface mounted provides high quality ecomonic energy saving lighting complete with all accessories internally pre-wired and including fixing the fitting on wall/ceiling with suitable PVC round/square block-02 Nos including connecting up with twin core twisted flexible copper conductor cable with suitable size and complete all as specified and directed by Engr-in-Charge. Make : Shakti cat No SZSLBMX020 or as approved by GE

Supply and fixing in repair new generation wall/surface mounted 1x 9 W LED batten fitting, 2 feet surface mounted provides high quality ecomonic energy saving lighting complete with all accessories internally pre-wired and including fixing the fitting on wall/ceiling with suitable PVC round/square block-02 Nos including connecting up with twin core copper conductor cable with suitable size and complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair new generation wall/surface mounted bluk head LED fitting 10W, provides high quality ecomonic energy saving lighting complete with all accessories internally pre-wired and including fixing the fitting on wall/ceiling including connecting up with copper conductor cable with suitable size complete all as specified and directed by Engr-in-Charge..

Supply and fixing in replacement LED 150W heavy duty LED highbay luminaires with toughened glass for added protection, secondary optics and IP66 protection complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement LED 120W Street/building security light fittings with high pressure die cast housing with toughened glass and individual LED with secondary optics and IP66 protection complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement MS arms bracket 30 degree bend, 1.5mtr long for mounting one in nos street light fitting including clamps / nut / bolts & washer to brace the same properly with duly painted in synthetic enamel paint of two coat in silver colour complete all as specified and directed by the Engr-in-Charge.

Supply & Fixing in repair of double door type vertical type TPN DB 6 Way ,415V with busbar , double door type IK 09 protection suitable for housing MCCB's complete all as specified and as directed by Engineer-in-Charge. Note : DBs shall be concealed in wall where ever possible including making good the surface to match with surrounding.

Supply & Fixing in repair of double door type SPN DB 08 Way ,240V with 100A copper busbar each phase , double door type IK 09 protection suitable for housing MCB's complete all as specified and as directed by Engineer-in-Charge. Note : MCB DBs shall be concealed in wall where ever possible including making good the surface to match with surrounding.

Supply & Fixing in repair MCB DB double door SPN 4 Way with 200 Amps rated copper bus bar, IP 54, IK 09 suitable for flush mounting and surface mounting complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing modular power socket 25A,2 module, 25A plug top, 25A mini MCB 'B' series 10 KA including 4 module box with cover plate complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing MCB SP 6-32 Amps,10KA, 'B' curve, complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing MCB SPN 40 Amps,10KA , 'B' curve complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing MCB TPN 40 Amps,10KA , 'B' curve complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing MCCB FP 100 Amps,16KA, complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for shifting of Split AC unit from existing postion & refixing the new position/location including outdoor stand as required, Servicing, leak testing, testing & commisssioning complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing copper tubings of appropriate dia for suction line & for liquid discharge line duly insulated with suitable insulation material including making hole in wall for passing through pipe and making good distrubed surface completely.

Material & Labour for sub-main wiring with 2 runs of 2.5 sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn in and including heavy grade PVC casing and caping not less than 25mm dia (internal width) with all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 2.5 sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains, with all accessories like PVC elbow, PVC tee, etc including taking up/down old unservicable sub main wiring and making good the distrubed surfaces/location complete all as specified and as directed by Engineer-in-Charge. Note: (a) Colour coding shall be followed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green

Material & Labour for sub-main wiring with 2 runs of 10.0sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn in and iincluding non metallic rigid PVC casing and caping not less than 25mm with all accessories fixed on wall//ceiling/truss etc as required, including one run of 10.0sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains, with all accessories like PVC elbow, PVC tee, etc including taking up/down old unserviceable sub main wiring and making good the distrubed surfaces/location complete all as specified and as directed by Engineer-in-Charge. Note:Colour coding shall be followed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green

Material & Labour for sub-main wiring with 2 runs of 4.0sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn in and including heavy grade PVC casing caping not less than 25mm dia (internal width) with all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 4.0sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains, with all accessories like PVC elbow, PVC tee, etc including taking up/down old unservucable sub main wiring and making good the distrubed surfaces/location complete all as specified and directed by Engr-in-charge. Note: (a) Colour coding shall be followed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green

Disconnecting & taking down old unserviceable cable & Supply and laying in repair cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50sq mm 3½ core complete all as specified and directed by Engr-in-Charge.

Supply and fixing GI cable tray perforated type 2 mm thick of size 450x50mm ( Including pre fabricated GI clamp suitable for fixing/supporting ) with0.71mm thick aluminium sheet cover, alloy 31000 H4 in ridges, Hips valley gutter cable trucking for plain to be fixed on any wall (brick/stone) vertically/horizontally including all accessories complete bending,shaping,drilling,welding, cutting & all fixing arrangement complete all as specified and as directed by Engineer-in-Charge.

RS Enterprises

SHREE JAGDISH FURNITURE CO.