Construction of road by providing interlocking Paver Block for setting up 102 bedded prefabricated COVID care Modular Hospital in the Campus of Civil Hospital BK Hospital NIT Faridabad REINVITED

Amount

Brick work with common burnt clay non-modular bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement: 6 coarse sand) [HSR 7.21.2]

Brick work with common burnt clay non-modular bricks of class designation 7 .5 in superstructure above plinth level up to floor IV level in all shapes and sizes in Cement mortar 1:4 (1 cement: 4 coarse sand) [HSR 7.22.1]

12 mm cement plaster of mix - 1 :4 (1 cement: 4 fine sand) [HSR 11.5.3]

15 mm cement plaster on the rough side of single or half brick wall of mix - 1 :4 (1 cement: 4 fine sand) [HSR 11.6.1]

Providing and applying two coats white cement based putty of approved brand and manufacturer, over plastered surface and grinding the surface smooth with sand paper to get en even and smooth finish including cost and carriage of all material , labour charges, scaffolding, sundries etc. complete [HSR 11.58]

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface - Water thinnable cement primer [HSR 11.67]

Wall painting with acrylic emulsion paint, having voe (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour- Two coats [HSR 11.74.2]

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade [HSR 11.78]

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and comers, all necessary fittings complete, including applying a priming coat of approved steel crimer. [HSR 13.6] (i) Using M.S. angels 40x40x6 mm for diagonal braces [HSR 13.6.1]

Using flats 30x6mm for diagonal braces and central cross piece [HSR 13.6.2]

Compaction of & preparation of sub grade including loosening, leveling of earth 225 mm thick top layer, rough dressing of soil, final dressing of earth to give level, camber, watering, rolling with road roller, compacting the bed to achieve minimum dry density as given in the Table 3000-2 as per technical clause 305 of MORT&H specifications (HSR 17.5.3)

Providing & laying 150mm Granular Sub-Base with Coarse Graded Material - Grading-I (Table:- 400-2) Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with Rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401.of MORT&H specifications. Grading I material (Based on HSR 17.15.1) Note: - 1.Only crushed metal material should be used. No local earth sand shall be used. The material finer than 425 micron shall have zero Plasticity Index (PI).2. Materials to be used and operations of manufacturing shall be approved by the engineer.

Providing and Laying 80 mm thick ISI marked Interlocking Paver Blocks conforming to IS 15658:2006/IRC SP 63: 2004 of all shapes and colours in design mix cement M 40 over the bed of 30 mm thick fine sand complete in all respect.(HSR 17.69.2)

Providing and laying of cement concrete blocks of size 0.450 m x 0.300 m x 0.15 m of cement concrete (C.C) M30 grade for edging of interlocking paver blocks as per technical specification clause 1503 (Based on HSR 17.66.1)

Earth work in excavation in foundations, trenches etc. in all kind of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, staking the excavated soil clear from the edge of excavation and subsequent filling around masonry, in 15cm layers with compaction, including disposal of all surplus soil, as directed with in a lead of 30 metres (HSR 24.10.2)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: (HSR 6.1.6) 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Reinforced cement concrete work in beams, suspended floors roofs having slope up to 15 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor four level, excluding the cost of centering, shuttering, finishing and reinforcement with 1: 1.5:3 (1 cement : 1.5 coarse sand(zone-111) : 3 graded stone aggregate 20 mm nominal size). (HSR 6.16)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor four level, excluding cost of centering, shuttering, finishing and reinforcement : (HSR 6.15.1) 1:1.5:3 (1 cement : 1.5 coarse sand(zone-111) : 3 cum graded stone aggregate 20 mm nominal size)

12 mm cement plaster of mix : 1 :2 (1 cement: 2 fine sand) (HSR 11.5.1)

Cement rendering on plaster 1 mm thick (HSR 11.52)

1O mm thick cement plaster- :3 (1 cement: 3 fine sand) (HSR 11.4.2)

Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect below plinth level- Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work , excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement- Cold twisted bars (HSR 6.33.3)

Providing and laying of flat brick or tile flooring with bricks of class designation 7 .5 laid in cement sand mortar 1 :4 on 100 mm thick cement concrete 1:8:16 and 100 mm sand filling and cement pointing 1 :2 on top.. (HSR 10.35.1)

Centering and shuttering including strutting, propping etc. and removal of form for (HSR 6.30.3) Suspended floors, roofs, landings, balconies

Providing, laying, jointing and testing of following sizes of pipes conforming to IS-1239 with all accessories like all fittings (upto 50mm dia threaded G.I.forged fittings and above 50 mm dia MS forged fittings with welded joints shall be used)fittings including tees, elbows, reducers, flanges, rubber gaskets, nuts bolts, washer. And fixing the pipe on floor / wall /ceiling with suitable size clamps, hangers, structural steel supports as per specification including cutting holes and chases in brick, R.C.C work and making good the same to original conditions complete in all respects.(Jindal,tata,prakash surya) (i) 200 mm dia (DSR 7.9)

150 mm dia (DSR 7.8)

100 mm dia (DSR 7.7)

Providing and fixing C.I.`Y' strainer with bronze perforated sheet basket tested to a pressure of 15 Kg/sqcm including rubber gasket, flanges, nuts, bolts and washers, complete as required. (KARTAR, LEADER, NEWAGE, SANT,KIRLOSKAR) (i) 150 mm dia (DSR 15.3)

200 mm dia (DSR 15.4)

Supplying , fixing, testing and commissioning of butterfly valve of PN.1.6 rating with bronze/gunmetal seat duly ISI marked complete with nut, bolts, washers, gaskets conforming to IS:13095 of following size as required Make:-KARTAR/ZOLOTO/CASTLE/KILOSKAR/NEWAGE/SANT OR EQUILENTS (i) a) 080 mm dia (DSR.11.4)

b) 065 mm dia (DSR.11.3)

Providing, Installation, testing and commissioning of non-return valve following size conforming to IS: 5312 complete with rubber gasket, G.I. nut and bolt washers etc. as required Make:- KARTAR/ZOLOTO/CASTLE/KILOSKAR/NEWAGE/SANT OR EQUILENTS. (i) a) 150 mm dia (DSR 14.7)

b) 100 mm dia (DSR.14.5)

c) 080 mm dia (DSR.14.4)

d) 065 mm dia (DSR.14.3)

Providing, and fixing of pressure relief valve suitable for pressure of 15 kg./sq.cm including flange, nut, bolt, washers etc. complete as required c.i. dual plate non-return valve PN. 1.6 rating 16kgkg/cm2 conforming to IS:778 and test pressure not less than 20 kg./cm2 complete 2 nos. matching flange, rubber inseration, with nut, bolts and washers etc. of following size : (N.S.)

Providing, fixing , testing and commissioning of pressure switch in mild steel pipe including connection etc. Make:- INDOFUS/DANFOS/SWITZER ( DSR. 22 )

Providing, fixing , testing and commissioning of 150mm dia bourden type brass Dfial typepressure guage celiberated for 0-16kg./sq.cm range with brass isolation valve complete.( N.S. )

Supplying, insstallation, testing and commissioning of 100 mm dia Draw of connection on fire water tank for fire brigade (N.S.)

Supplying, insstallation, testing and commissioning of 100 mm dia emergency connection on fire water tank for fire brigade (N.S.)

Supplying, insstallation, testing and commissioning of cast iron foot valve connection with all accessories with the tech space 15360 in fire water tank -100mm dia (N.S.)

Supplying, insstallation, testing and commissioning of air vessel nade out of 250mm dia, 8mm thick mild shteel sheet 1200 mm in height with air release valve on top end flangee connection to vertical and horizontal pipe / riser drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure guage and painting with synthetic enamel paint of approved shade as required : FIRE CUT/HYDROTECH/ SALEX ETC.(DSR.- 20 )

Supplying, insstallation, testing and commissioning of four way fire brigade inlet connection in mains near suitable connection location with non-return valve 150mm dia and btter fly valve 150mm dia all accessories located on fire water tank and around the building ring mains as required. (N.S.)

Supplying, fabricating structuralsteel supports such as mild steel channel, angles, fltas rods as required at site with anchor fasstners claimps, treaded rods, nut, bolts, washers etc. as required complete with paintings. (.N.S. )

Supplying, insstallation, testing and commissioning of water level indication including all necessary fittings an cabling up to panel. ( N.S. )

Supplying, insstallation, testing and commissioning of anti vortex devoice including elbow for 150mm dia pump suction line. ( N.S. )

Supplying, installation, testing and commissioning of single headed internal and external yard hydrant valve instantaneouse stainless steel couplng of 63mm dia with cast iron wheel ISI marked conforming to IS: 5290 (ype - A ) with blanck stainless steel cap and chain as required (Make :- TYCO, SAFEX,HD,KARTAR,SALEX,FIRECUTE, PGC,NEWAGE,ETC.( DSR.) -:( 9.2 )

Supplying, installation, testing and commissioning of 63mm dia 15 mtrs. long RRL hose pipe with 63mm dia maale and female couplings duly bound with G.I. wire, rivets etc. confroming to IS: 636 ( type - A ) as required (Make :- FIRE CUT/NEWAGE/ SALEX/ KARTAR, PGC/ MINIMAX, SAFEX) ETC (DSR:- 16.2 ).

Supplying, installation, testing and commissioning of 63MM DIA STAINLESS STEEL (GRADE 304 ) short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS : 903 suitable for instantaneouse connection to IS: 903 suitable for inter connecte hose pipe coupling as required ( Make :- TYCO, SAFEX,HD, KARTAR, SALEX, FIRECUTE, PGC,NEWAGE,ETC. ( DSR.) -: ( 18.2 )

Providing, fixing, testing and commissioning of fire man axe conforming to IS:926 - 1985 with claimp ( N.S. )

Supplying , fixing, testing and commissioning of butterfly valve of PN.1.6 rating with bronze/gunmetal seat duly ISI marked complete with nut, bolts, washers, gaskets conforming to IS:13095 of following size as required Make:-KARTAR/ZOLOTO/CASTLE/KILOSKAR/NEWAGE/SANT OR EQUILENTS ETC. (i) 150 mm dia (DSR 11.6)

100 mm dia (DSR 11.5)

Providing, fabricating and fixing double leaf door with frame only for internal fire hydrants fabricated frm MS sections, welded construction, having glazed panels with reinforced glass with locking arrangement, stove enameled fire red finish with “Fire Hose” written on front, suitable to house two nos. 15 m lengths of RRL hose with couplings, 1 No. Branch pipe and 1 No. First Aid Fire Hose Reel along with the landing valve all complete (Door Size-2100 x 1200mm) (N.S)

The Kapil CoOp LandC Society Ltd