Providing RCC platform and internal painting works to CSD 1st floor of old chemical Engg building and Partition works to Room No 003 in Dept of MME and Room No CH501 in New Chemical Engg building

Amount

Dismantling plastering: Dismantling wall plastering (either in cement mortar or lime mortar), removing, transporting and disposal of the debris with all lead and lift etc. complete

Cement concrete Solid blocks: Providing and constructing non load bearing wall with solid concrete blocks of size 400x100x200mm having a block density not less than 1800kg/cum having minimum average compressive strength of 4.00N/mm2 confirming to IS 2185 (Part 1): 2005 and constructed with CM 1:4 as per IS 2572:2005 including cost of all materials, labour charges, scaffolding, curing, hire charges of machineries et., complete as per specifications. KBS No5.4.

TMT steel reinforcement for RCC work: KSRB 4.9.2: Providing TMT steel reinforcement for R.C.C. work including straightening, cutting, bending, hooking, placing in position, lapping and / or welding wherever required, tying with binding wire and anchoring to adjoining members wherever necessary, all laps and wastage complete as per design (laps, hooks and wastage shall not be measured and paid) cost of materials, labours, HOM of machinery complete as per specifications. Specification No. KBS 4.6.3. Fe-500 grade TMT steel from the primary producers such as SAIL/ TISCO/ RINL/ IISCO/ VIZAG as approved by the Ministry of Steel shall only be used. - in 6th Floor

M20 for RCC Platform: KSRB 4.2.8: Providing and laying in position reinforced cement concrete of design mix - M20 - with OPC cement at 320 kgs/ PPC/ PSC cement with 20mm and down size graded granite metal coarse aggregates at 0.69 cum and clean sieved fine aggregates at 0.46 cum with superplasticizer at 3ltrs conforming to IS 9103 -1999 Reaffirmed-2008,machine mixed, concrete laid in layers not exceeding 15 cms thick, vibrated for RCC works of all sizes including cost of all materials, labour HOM of machinery curing complete as per specifications (excluding cost of steel and fabrication charges). Design mix test should conform to IS 456:2000 - Specification No. KBS 4.1, 4.6

Centering/shuttering for RCC platform: KSRB 4-6.10: Providing and removing centering, shuttering, strutting propping etc., for RCC platform etc., including edges including cost of all materials, labour complete as per specifications. Specification No. KBS 4.6.2

Cudapa slabs : Providing 20mm thick cudapa slab using cement mortar 1:6 25mm thick over existing cement concrete bed or top of roof laid to line and level and jointed with cement slurry mixed with pigment to match the shade of the slab, including cost of materials, labour, curing, polishing complete as per specifications., Specification No. KBS

Nosing for Cudapa : Providing half nosing for 20mm thick cadapa slab using required machinery including cost and conveyance of all materials, labour for all items of work, HOM of equipment, necessary scaffolding etc., complete as per specification.

12mm thick Plastering in cm 1:4:- (Ceiling) : Providing 12mm thick cement plaster in single coat with cement mortar 1:3, to Ceiling surface including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labours, coring complete as per specifications.

15mm thick Plastering in cm 1:4 – (wall surface) : Providing 12mm thick cement plaster in single coat with cement mortar 1:4, to wall surface including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labours, coring complete as per specifications.

Plastic emulsion painting for Ceiling surface – in two coats: Providing and applying painting in two coats with plastic emulsion paint of approved brand (Asian Emulsion/ Nerolac/ Berger/ Nitco/ equivalent) over one coat of Asian paints Deco Prime wall primer / equivalent on ceiling surface to give an even shade after thoroughly brushing the surface, free from mortar drops and other foreign matter including preparing the surface even and sand paper smooth, cost of all material, labour etc complete as per specifications.

Plastic emulsion painting for walls –in two coats: Providing and applying painting in two coats with plastic emulsion paint of approved brand (Asian Emulsion/ Nerolac/ Berger/ Nitco/ equivalent) over one coat of Asian paints Deco Prime wall primer / equivalent on wall surface to give an even shade after thoroughly brushing the surface, free from mortar drops and other foreign matter including preparing the surface even and sand paper smooth, cost of all material, labour etc complete as per specifications.

Laboratory sink: Providing and fixing laboratory sink of white glazed fire clay of size 600x 450x200 mm with M.S / CI brackets, CP brass chain with rubber plug, 32mm C.P brass waste, tap with union, brass stop cock complete, painting of fittings and brackets, curring and making good the wall and floor wherever required, including cost of materials labour complete as per specifications.

UPVC plumbing pipes – 32 mm dia: KSRB: 13.10 Providing and fixing to wall, ceiling and floor unplasticised PVC pipes 10kgs/sqcm working pressure of out side dia meter with approved make with fittings, wall clips making good the wall, ceiling and floor including cost of all materials, with all lead and lift for all the floors, including scaffolding, labour charges, - 32 mm nominal dia pipes

UPVC plumbing pipes – 16 mm dia: KSRB: 13.10 Providing and fixing to wall, ceiling and floor unplasticised PVC pipes 10kgs/sqcm working pressure of out side dia meter with approved make with fittings, wall clips making good the wall, ceiling and floor including cost of all materials, with all lead and lift for all the floors, including scaffolding, labour charges, - 16 mm nominal dia pipes

Wall bore: Wall bore in stone masonry up to 45cm thick including cost of materials, labour, necessary scaffolding, HOM complete as per specifications. Up to 45cm thick.

PVC pipe – 63 mm dia – 6kgf/ sqcm class: Providing and fixing in wall, ceiling and floor PVC pipes 6.00 kgf/sqcm working pressure 63 mm outside diameter conforming to IS specification with fittings such as elbows, bends, couplings, wall clips/ brackets, making good the wall ceiling or floor including cost of all material, labour charges, HOM of equipment and testing etc., complete as per specification.

32mm dia brass ball valve: Providing and fixing in position brass ball valve of approved quality nominal bore including cost of all materials, labour and HOM with all leads complete as per specification.

GRP Door shutter 32 mm thick – Providing and fixing factory made single leaf rigid GRP Sandwich composite door shutter of 32mm thick, laminated with two GRP skins with wood grain finish, fabricated using U.V- stabilized Isopthalic Gelcoat and on layer of 450gsm E-Glass Chopped strand Mat (CSM), impregnated with orthopthalic polyester resin. The thickness of the skins shall not be less than 1.5mm. Expanded polystyrene EPS) structural foam panel of 29mm thickness and a density of 20 kg/m3 shall be used as core material. Wooden reinforcements made of Seasoned Salwood block of cross section not less than 28x32mm and also necessary salwood reinforcements for fixing the metal fittings such as tower bolts, aldrops, handles, etc., shall be provided. A structural adhesive compatible with EPS foam shall be used for bonding the core material, the salwood reinforcement and the skins. The material and process for manufacturing the door shutters shall conform to RV/TIFAC Composites Design center Standards and specifications and the door shutters tested in conformation to IS 4020-1994. The finish of shutter will be plain colour White/Ivory/Beige/Light Grey or any other colour using high quality pigments, and inclusive of supply of shutter to respective work spot (excluding cost of fixture)

GRP Door frame: Providing and fixing 65mmx125mm GRP Door frame fabricated using E-Glass Chopped strand Mat (CSM) UV- stabilized Isopthalic Gelcoat and Isopthalic resin. The thickness of the GRP skin shall not be less than 2.0 mm. The door frame consists of four segments, which are provided with plug-in-socket arrangement in-situ in the mould. The segments are plugged in and are joined together by means of screws. The GRP frame shall be provided with wooden reinforcement on locations for high screw holding capacity for fixing metalling hold fast and shall be consolidated by filling with medium density foam/Plaster of Paris with fibre reinforcement. Six numbers of 260mm x 25mm x5mm size S shaped M.S.flat hold fast shall be provided with the frame.

Solid PVC Door frame: Providing and fixing factory-made PVC door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet metered cut at corners and jointed 2 Nos of 150mm long brackets of 15x15mm M.S square tube, the entire door frame to be reinforced with 19x19mm M.S Square tube of 19 gauge. The door frame to be fixed to the wall using M.S Screws of 65/80mm size complete as per manufacturers specifications and direction of Engineer -in-charge. – in 6th floor

Enamel painting on previously wooden surface: KSRB 15-17.19: Providing and applying painting in One coat on previously painted wood surface and/ or wood based surface with enamel paint (to give an even shade, cleaning oil, grease, dirt and foreign matter, sand papering and knotting ready mix paint including cost of material and labour complete as per specifications - Asian /Nerolac/ Berger or equivalent Make

Painting to previously painted steel work – in One coat: Providing and applying enamel metal paint one coat ( excluding priming coat) on previously painted steel or other metal surface brushing to give an even shad after cleaning oil, grease, dirt and other foreign matter, including cost of materials, labour, complete as per specifications.

Repairs of existing Aluminium window shutter: Providing repairs to aluminium window shutters by dismantling the shutters from the frame, cleaning the track, replacing glass beading with PVC white U beading, replacing the rusted screws and refixing the shutter to the frame after tightening the frame firmly to the wall, checking the smooth sliding movement of the shutter including cost of material, labour, transportation lead and lift, scaffolding wherever necessary etc., complete.

Plastic emulsion painting for ceiling without primer: Providing and applying painting in One coat with plastic emulsion paint of approved brand (Asian Emulsion/ Nerolac / Berger/ Sherwin Williams/ equivalent) on ceiling surface without primer to give an even shade after thoroughly brushing the surface, free from mortar drops and other foreign matter including preparing the surface even and sand paper smooth, cost of all material, labour etc complete as per specifications.

Plastic emulsion painting for walls without primer: Providing and applying painting in two coats with plastic emulsion paint of approved brand (Asian Emulsion/ Nerolac/ Berger/ Sherwin Williams/ equivalent) on wall surface without primer to give an even shade after thoroughly brushing the surface, free from mortar drops and other foreign matter including preparing the surface even and sand paper smooth, cost of all material, labour etc., complete as per specifications.

Floor paint: Providing and applying floor painting with ready mix paint in Two coats ( excluding primer coat ) on concrete / plastered / floor surfaces brushing to give an even shade after preparing the surface after thoroughly cleaning oil, dirt, Dust other foreign matter, including cost of materials, labour, complete as per specifications or as directed.

Colour anodized Aluminium partitions: Providing, fabricating, assembling and fixing in position aluminium partition using 101.60mm x 44.45mm x 3.18mm aluminium, mat finish or glossy finish, anodized sections combination of plain, single groove and double groove members should not exceed 0.60m c/c and bottom member of required lengths, joints mitred and corner grinded sub dividing assembled frame should be stiffened with corner angles. Stripped and fixed with screws rawl plug and teakwood guttas to RCC column or masonry on sides. RCC lintels or beams at tops and mosaic floor at bottom; including cutting chistelling and making good with cement mortar to match the surface. Providing and fixing 12mm thick prelaminated sheet (Ecoboard - exterior grade ) of approved colour for bottom panel of maximum height 0.90m, and 5.50mm thick plain or pin headed glass for middle panel and top panel with glazing clips of 19.05mm x 17.30mm.1.00mm . All the aluminium sections used should be treated for removal of any rust and prevention of futher rust formation and coated with greasy materials for non adherence of mortar or any other sticky materials: The vertical members should be embedded in the flooring by making suitable size holes and fixing with cement motar. All the frame should be thoroughly cleaned free from rust, scale or dirt. Work should be carried out as per direction of engineer-in-charge of the work with all lead and lift as per chief Architect’s drawing etc., complete to a degree of perfection.-using aluminium section anodized to 12-15 microns – for Ground floor

Colour anodized Aluminium partitions: Providing, fabricating, assembling and fixing in position aluminium partition using 101.60mm x 44.45mm x 3.18mm aluminium, mat finish or glossy finish, anodized sections combination of plain, single groove and double groove members should not exceed 0.60m c/c and bottom member of required lengths, joints mitred and corner grinded sub dividing assembled frame should be stiffened with corner angles. Stripped and fixed with screws rawl plug and teakwood guttas to RCC column or masonry on sides. RCC lintels or beams at tops and mosaic floor at bottom; including cutting chistelling and making good with cement mortar to match the surface. Providing and fixing 12mm thick prelaminated sheet (Ecoboard - exterior grade ) of approved colour for bottom panel of maximum height 0.90m, and 5.50mm thick plain or pin headed glass for middle panel and top panel with glazing clips of 19.05mm x 17.30mm.1.00mm . All the aluminium sections used should be treated for removal of any rust and prevention of futher rust formation and coated with greasy materials for non adherence of mortar or any other sticky materials: The vertical members should be embedded in the flooring by making suitable size holes and fixing with cement motar. All the frame should be thoroughly cleaned free from rust, scale or dirt. Work should be carried out as per direction of engineer-in-charge of the work with all lead and lift as per chief Architect’s drawing etc., complete to a degree of perfection.-using aluminium section anodized to 12-15 microns – for 5th floor

Aluminium door : KSRB 7.16: Providing, fabricating, assembling and fixing in position aluminium shutters to the existing door frame in the partition using 47.62 x 44.45mm section thickness 3.18mm, weight 1.505kg/m for vertical frame, 47.62x44.45 thickness of 3mm, weight 1.42kg/m for top section, 49.91mm x44.45mm with wall thickness 3mm weight 1.495kg/m for central rail; and 114.3mm x 44.45mm thickness 3.18mm, weight 2.646kg/m for bottom rail; aluminium sections and cut to length joint metred and corners grinded, the bottom rail and top rail hinged or pivoted, opening arrangements including providing and fixing standard approved accessories, such as aluminium handles, tower bolts, lock, pivots: hinges PVC. Or rubber gasket, 12mm prelaminated sheets (Novopan) exterior grade of approved colour both sides same colour for bottom panel of maximum height 0.90m and 5.5mm thick plain glass for top panel (Novopan) and glass fixed with glazed clips 19mm x17.3mmx11mm, 0.9mm thick, weight 0.124kg/m; aluminium sections treated for removal of any rust and prevention of further rust formation, and coated with greasy materials for non-adherance of mortars or any other sticky materials, including cost of materials, fixtures, labour and HOM of machinery complete as per specifications.- using aluminium section anodized to 12-15 microns.- in Ground Floor

Aluminium door : KSRB 7.16: Providing, fabricating, assembling and fixing in position aluminium shutters to the existing door frame in the partition using 47.62 x 44.45mm section thickness 3.18mm, weight 1.505kg/m for vertical frame, 47.62x44.45 thickness of 3mm, weight 1.42kg/m for top section, 49.91mm x44.45mm with wall thickness 3mm weight 1.495kg/m for central rail; and 114.3mm x 44.45mm thickness 3.18mm, weight 2.646kg/m for bottom rail; aluminium sections and cut to length joint metred and corners grinded, the bottom rail and top rail hinged or pivoted, opening arrangements including providing and fixing standard approved accessories, such as aluminium handles, tower bolts, lock, pivots: hinges PVC. Or rubber gasket, 12mm prelaminated sheets (Novopan) exterior grade of approved colour both sides same colour for bottom panel of maximum height 0.90m and 5.5mm thick plain glass for top panel (Novopan) and glass fixed with glazed clips 19mm x17.3mmx11mm, 0.9mm thick, weight 0.124kg/m; aluminium sections treated for removal of any rust and prevention of further rust formation, and coated with greasy materials for non-adherance of mortars or any other sticky materials, including cost of materials, fixtures, labour and HOM of machinery complete as per specifications.- using aluminium section anodized to 12-15 microns.- in 2nd Floor

Aluminium door : KSRB 7.16: Providing, fabricating, assembling and fixing in position aluminium shutters to the existing door frame in the partition using 47.62 x 44.45mm section thickness 3.18mm, weight 1.505kg/m for vertical frame, 47.62x44.45 thickness of 3mm, weight 1.42kg/m for top section, 49.91mm x44.45mm with wall thickness 3mm weight 1.495kg/m for central rail; and 114.3mm x 44.45mm thickness 3.18mm, weight 2.646kg/m for bottom rail; aluminium sections and cut to length joint metred and corners grinded, the bottom rail and top rail hinged or pivoted, opening arrangements including providing and fixing standard approved accessories, such as aluminium handles, tower bolts, lock, pivots: hinges PVC. Or rubber gasket, 12mm prelaminated sheets (Novopan) exterior grade of approved colour both sides same colour for bottom panel of maximum height 0.90m and 5.5mm thick plain glass for top panel (Novopan) and glass fixed with glazed clips 19mm x17.3mmx11mm, 0.9mm thick, weight 0.124kg/m; aluminium sections treated for removal of any rust and prevention of further rust formation, and coated with greasy materials for non-adherance of mortars or any other sticky materials, including cost of materials, fixtures, labour and HOM of machinery complete as per specifications.- using aluminium section anodized to 12-15 microns.- in 5th Floor

Resetting of aluminium existing partition: Removing existing aluminium partition section and resetting aluminium partition for required size cost including cutting the frames, corner, grinding, resetting size of existing glass, beading etc., complete as per direction of the Engineer in charge. size : 1.22m x2.13m

EKADANTHA CONSTRUCTION

BHARATESH V KULAL