REPAIR TO FACIA, CHAJJA, COLUMN TO CERTAIN BLDGS AND OTHER MISC WORKS AT VAYUSENABAD AND REPAIR TO WOODEN FURNITURE AT AF STN TUGHLAKABAD UNDER GE (AF) TUGHLAKABAD

Amount

M&L for gunniting to RCC works in column, beams, slabs, chajja, facia, landing, balconies etc by removing/ dismantling of RCC (loose concrete) including plaster and cutting of steel bar including plaster cleaning of surfaces with wire brushes and applying epoxy, paint anti corrosive coating of minimum 40-50 microns thick with sikatop Armatec 108 or Colusal VL of MC Bauchemie to rusted steel reinforcement after removing cleaning all rust and supply and fixing welded steel wire mesh 75mm x75mm with 4mm dia steel wire as facies/drops and similar work etc and epoxy based or other equivalent suitable bonding against treatment to be carried out on old concrete surface with Sikadur 32 of Sikka. Nito bond EP of fosroc or equivalent (as per manufacturers instruction) to bond old and new concrete mixing @ 2% by weight of cement polycrete and providing gunniting with a minimum pressure of 2 to 2.5 Kg sqcm and applying 25mm to 100 mm thick gunniting in cement mortar (1:2) (1 part of cement and two part of ghaghar sand) with plastering(1:4) using ordinary port land cement of 43 grade over wherever required at any height complete all as specified and directed by Engr-in-charge. Note: All windows and doors shall be covered by tarpaulin sheet. (i) After placing the additional reinforcement all concrete surface shall be thoroughly scrubbing with. (ii) Additional reinforced TMT bars where incorporated in work and including 20mm thick cement plaster in 1:4 to be included in quoted rate. (iii) Work to be carried out as in patches and scattered locations of bldgs as directed by Engr-in-charge. (iv) Rate for steel scaffolding deemed to be included in quoted rate. (v) All demolished material removed from MOD land completely. No extra cost claimed by contractor for same.

M&L for mild steel TMT bars 10mm dia and over cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engr-in-charge.

M&L for TMT steel bars 6mm to 8mm dia and over cut to length bent shape required, including cranking bending binding with mild steel wire (annealed) not less than 0.9mm dia quality conforming to relevant IS complete all as specified and directed by Engr-in-charge.

Re-baring by drilling holes and fixing nozzle if required in existing concrete/brick work as in column, beams, slabs and foundation etc in any position and any description size of hole 14mm, 16mm & 22mm suitable for dowels of size 10mm, 12mm & 16mm respectively (minimum depth 140mm for 10mm & 12 mm dia bars and 180mm for 16mm dia bar, cleaning the surface properly with blow out pump & round brushes and fixing of dowel bars with epoxy resin (resin+hardner) complete all as specified and directed by Engr-in-charge. Note:- (i) Adequate lap length shall be provided as per IS-456-2000. (ii) Reinforced TMT bars where incorporated in work will be paid under item no 2&3. (iii) The work shall be carried out upto four storied building with scaffolding.

M&L for providing and applying corrosion resistance non-shrink free flow, cementious one component Micro-concrete with average thickness 75mm having compressive strength (BS 4551-80-60) 50 MPA at 28 days, Tensile strength (ASTM C 348)-2.0 N/mm2 @ 28 days, Flexural strength (ASTM C 348)-9 epoxy bonding agent TM bond EP thermax having mix density of 1.45 to 1.5 kg/ltr, compressive strength (BS-6319 PT 3)-25 Mpa at 7 days bond strength (ASTM C 881)- 11 N/mm2 at 7 days, having an over lay time of 3 hrs at 30°C pouring of micro concrete into the formwork using suitable arrangement or if required using pumping device for and the necessary shuttering after 7 days ensuring proper bond between the micro concrete and existing concrete substrate etc including all tools and tackles as per accepting office, complete all as specified and directed by Engr-in-charge. Note: Rate deemed to be included scaffolding and shuttering

M&L for 15mm thick rendering in CM 1:4 on fair faces of brick or concrete surfaces finished even and smooth without using extra cement including taking down loose cement plaster on brick, stone walls and concrete surfaces (except above mention in description 1 area) of any description/position etc including racking out joints, hacking for keys scrubbing down with water etc complete all as specified and directed by Engr-in-charge. Note: - All works to be carried out up to Approx 12 mtr height. Rates included to the necessary steel scaffolding required for execution of works upto Approx 12 mtr height from ground floor. No extra claim by the contractor for same. All dismantling/ demolished material removed from MOD land completely. Rate of removal outside side from MoD land deemed to be included in the same item.

M&L for 15mm thick rendering in CM 1:6 on other than fair faces of brick or concrete surfaces finished even and smooth without using extra cement including taking down loose cement plaster on brick, stone walls and concrete surfaces (except above mention in description 1 area) of any description/position etc including racking out joints, hacking for keys scrubbing down with water etc complete all as specified and directed by Engr-in-charge. Note: - All works to be carried out up to Approx 12 mtr height. Rates included to the necessary steel scaffolding required for execution of works upto Approx 12 mtr height from ground floor. No extra claim by the contractor for same. All dismantling/ demolished material removed from MOD land completely. Rate of removal outside side from MoD land deemed to be included in the same item.

M&L for 5mm thick rendering in CM 1:3 on concrete/gunniting surface as in ceiling finished even and smooth w/o using extra complete including taking down loose cement plaster on brick, stone walls and concrete surfaces (except above mention in description 1 area) of any description/position etc including racking out joints, hacking for keys scrubbing down with water etc complete all as specified and directed by Engr-in-charge. Note: - All works to be carried out up to Approx 12 mtr height. Rates included to the necessary steel scaffolding required for execution of works upto Approx 12 mtr height from ground floor. No extra claim by the contractor for same. All dismantling/ demolished material removed from MOD land completely. Rate of removal outside side from MoD land deemed to be included in the same item.

M&L for two coat of exterior emulsion paint on newly plastered over primer of walls to match the existing colour incl preparation the surface (External) complete all as specified and directed by Engr-in-charge.

M&L for preparing newly surfaces of ceilings and applying three coat of white wash on new surface complete all as specified and directed by Engr-in-charge.

M&L for preparation of new plastered surfaces of walls and applying two coat of Oil Bound distemper over 1mm thick wall putty on new wall surface, complete all as specified.

M&L for preparation of old decorated plastered or unplastered surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil & greasy spots including cornices etc and applying two coat of oil bound distemper white or tinted over a coat of white putty in patches as required complete all as specified and directed by Engr-in-charge.

M&L for preparation of old surface of brick/concrete wall surface by brushing, washing and applying two coat of exterior emulsion paint on old decorated surface complete all as specified and directed by Engr-in-charge. Note:- Quoted rate shall be deemed to be included for work in buildings/ structure of any height.

M&L for cutting chases n. exc 10 cm girth in brick wall and making good in cement mortar 1:3 for embedding of GI sheet in wall complete all as specified and directed by Engr-in-charge.

S&F in repair Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-charge.

S&F rolled sections as in framing for cladding, glazing and the like etc fixed with angle clips and connecting plates etc FE 410 W Gde E-250 quality B fixed with fastener complete all as specified and directed by Engr-in-charge.

M&L for Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed by Engr-in-charge.

Demolition of RCC of any description and in any position at any height not otherwise specially provided for reinforcement cut as required to facilitate demolition complete all as specified and directed by Engr-in-charge.

M&L for cement concrete type B-0 12.5mm graded stone aggregate , in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, complete all as specified and directed by Engr-in-charge.

S&F in repair PVC (SWR) pipes single socketed 110mm dia in any length with rubber ring joints fixed to walls complete all as specified and directed by Engr-in-charge.

S&F in repair PVC (SWR) bends 110mm dia any radius complete all as specified and directed by Engr-in-charge.

S&F in repairs vitreous China squatting pan of Orissa pattern of approved make of size 580 mm X 440 X 260 mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe incl lime concrete bedding and connection to anti syphonage pipe etc including making good to floor complete all as specified and directed by Engr-in-charge. Note: All dismantling/demolished material removed from MOD land completely. Rate of removal outside side from MoD land deemed to be included in the same item.

S&F in repair vitreous china wash down water closet pan (pedestal pattern) white (excluding fixing bolts flushing cistern and flush pipe) with seat cover with CP screw complete all as specified and directed by Engr-in-charge.

S&F in repair A Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed by Engr-in-charge.

S&F in repair of PVC low level flushing cistern of 10 ltrs capacity with top push button inclusive of brackets and PVC bend long type and connection to flush pipe of any size and pattern with inlet ball valve float and handle of approved make complete all as specified and directed by Engr-in-charge.

S&F in repair of wash hand basin of size 550 x 400 mm vitreous China white flat back including brackets, waste coupling & PVC waste pipe of 32 mm dia etc. complete all as specified and directed by Engr-in-charge.

S&F in repair of 32 mm bore of pipe low density (LDPE) of pressure rating 6 kg/ sqcm fixed to wall or floor etc including fittings complete all as specified and directed by Engr-in-charge.

S&F in repair of 15mm bore chromium plated Pillar cock screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and directed by Engr-in-charge.

S&F in repair of PVC connection 15 mm size with PTMT nuts of length 450 mm of approved quality complete all as specified and directed by Engr-in-charge.

S&F in repair angle valves CP screwed down high pressure of fancy type chromium plated screwed both ends for iron pipe or for union and fixed with 15mm bore complete all as specified and directed by Engr-in-charge.

S&F in repair of brass chromium plated shower rose 125 mm of size with arm and with or without swivel joints to steel pipe or union complete all as specified and directed by Engr-in-charge.

S&F in repair of 15 mm dia bore concealed stop valves cast copper alloy chromium plated fancy type with long shank & cup (concealed type) complete all as specified and directed by Engr-in-charge.

S&F in repair brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges complete all as specified and directed by Engr-in-charge.

S&F in repair of CP soap tray fixed to walls with rubber plugs complete all as specified and directed by Engr-in-charge.

S&F in repair of 15 mm dia bore bib taps cast copper alloy with crutch and butterfly handle, screwed for iron pipe, or for brass ferrule complete all as specified and directed by Engr-in-charge.

S&F in repair sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, etc complete all as specified and directed by Engr-in-charge.

S&F in repair of 125mm dia grating doom with/without waste hole of PTMT (Minimum weight 40 gms) complete all as specified and directed by Engr-in-charge.

S&F in repair of for 25mm dia fancy type PVC coated on MS Pipe coloured curtain rod with brackets and knobs at both ends as per site requirement including taking down old existing PVC conduit pipes with accessories complete all as specified and directed by Engr-in-charge. Note : The cost of brackets and knobs is deemed to be including in the quoted rate. Nothing extra shall be paid on this account.

Taking down or up 15 mm bore galvanised iron tubing and connection and S&F GI tubing medium grade with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 15 mm complete all as specified and directed by Engr-in-charge.

All as per serial item 40 here in before but 20 mm bore complete all as specified and directed by Engr-in-charge.

Taking down and refixing only old GI tubing 15 mm bore pipe and connections in new or old position as on walls ceiling floors etc complete all as specified and directed by Engr-in-charge.

All as per serial item 42 here in before but 20 mm bore complete all as specified and directed by Engr-in-charge.

M&L for removing building old materials etc. (broken tiles, broken bricks, broken others building materials) to a distance of 1500m (outside of MoD land), beyond the lead included in the rates, including loading, unloading and stacking at the destination complete all as specified and directed by Engr-in-charge.

S&F non skid ceramic coloured tiles of 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm with 15 mm thick Screed bed or bedding layer in CM (1:6) including dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed by Engr-in-charge. Note: All dismantling/demolished material removed from MOD land completely. Rate of removal outside side from MoD land deemed to be included in the same item.

S&F glazed ceramic coloured tiles 7mm thick 450 x 300mm size in vertical surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to the shade. Etc including 10 mm thick rendering in CM 1:4 including dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed by Engr-in-charge. Note: All dismantling/demolished material removed from MOD land completely. Rate of removal outside side from MoD land deemed to be included in the same item.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors over 15 mm thick screed bed in CM (1:6) etc set and jointing in neat cement slurry and pointed in white or coloured cement to match, including dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed by Engr-in-charge. Note: All dismantling/demolished material removed from MOD land completely. Rate of removal outside side from MoD land deemed to be included in the same item.

Note for item Nos 1 to 47 above 1. All works to be carried out up to Approx 15 mtr height. Rates included to the necessary steel scaffolding required for execution of works upto Approx 15 mtr height from ground floor and disposal of all demolished material from outside the MOD land. 2. The work will be scatted in nature various buildings according to site requirement and as directed by Engineer-in- Charge.

Sofa set to seat five (FD-281) Taking out the torn out unserviceable cushion set of one seat & one back from Sofa set (FD-281) and supply new foam cushion set made of superior quality cushion of 40 density 100mm thick of size 530x560mm including tapestry cloth cover stiched on all sides with tapestry cloth of approved shade/texture costing not less than Rs 450/- per Sqm complete all as shown in drg and directed by Engr-in-Charge.

Taking out the unserviceable long rail from the sofa set of three seater (FD-281) and S&F of new long rail made out of well seasoned first class hard wood as per existing shape and size complete all as per drg and directed by Engr-in-Charge.

Taking out the unserviceable short rail from the sofa set three seater (FD-281) and S&F of new short rail made out of well seasoned first class hard wood without changing the shape and dimensions complete all as per drg

Taking out the unserviceable legs from sofa set of three seater (FD-281) and S&F of new leg made out of well seasoned first class hard wood as per existing shape and size complete all as per drg and directed by Engr-in-Charge.

Taking out the unserviceable strip from the back of sofa set three seated (FD-281) and S&F of new strip made out of well seasoned first class hard wood as per existing shape and size complete all as per drg and directed by Engr-in-Charge.

Bed with plywood top (FD-246) Taking out the unserviceable footrest from the bed with plywood top and S&F new footrest made out of well seasoned teak wood duly covered with decorative type plywood of commercial type 4 mm thick with one side teak face ISI Marked complete all as shown in drg and directed by Engr-in-Charge.

Taking out the unserviceable Headrest from bed with plywood top and S&F new Headrest made out of well seasoned teak wood duly covered with decorative type plywood commercial of 4 mm thick one side teak face complete all as shown in drg and directed by Engr-in-Charge.

Taking out the unserviceable long rail from Bed with plywood top and S&F new long rail made of well seasoned hard wood as per existing shape and size complete all as shown in drg and directed by Engr-in-Charge.

Taking out the unserviceable short rail from Bed with plywood top and S&F new short rail made out of seasoned hard wood as per existing shape and size complete all as shown in drg and directed by Engr-in-Charge.

Taking out the old unserviceable centre Stiffeners from bed plywood top and S&F of new centre stiffeners made out of well seasoned hard wood as per existing shape and size complete all as shown on drg and directed by Engr-in-Charge.

Taking out the unserviceable top plywood from Bed with plywood top and S&F new plywood of commercial type of 12mm thick ISI Marked superior quality as per existing shape and size all as shown on drg and directed by Engr-in-Charge.

Taking out the old unserviceable MS supporting Clamp from the bed with ply top and S&F of new clamps made out of 25mmx6mm MS flat iron fitted supporting to long rails all as shown on drg and directed by Engr-in-charge.

Table 900x600x760mm with/without drawer (FD-223, 224 283 & 284) Taking out the unserviceable top from table 900x600mm and S&F new top made out of pre-laminated particle board of one side teak face, exterior grade of 18mm thick duly provided with 4mm thick teak wood beading all round the top complete all as shown on drg and directed by Engr-in-Charge.

Taking out the unserviceable leg from the table 900x600mm and S&F new leg made out of well seasoned teak wood as per existing shape & size including PVC shoes of all four legs to be replaced with new one of superior quality for proper balancing to the repaired table complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable long rail from the table 900x600mm without drawers and S&F new long rail made of well seasoned teak wood as per existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable short rail from the table 900x600mm with drawers and S&F new short rail made of well seasoned teak wood as per existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable centre stiffener from the table 900x600mm and S&F new centre stiffener made out of well seasoned teak wood as per existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable drawers from the table 900x600mm and S&F new drawers made out of 12mm thick teak wood except bottom of drawers shall be of 6mm thick ply wood commercial ISI Marked complete all as shown in drg and directed by Engr-in-Charge.

Taking out old unserviceable knobs from the drawers of table 900x600mm with drawer and S&F of new Knobs as per approved quality complete all as shown in drg and directed by Engr-in-Charge.

Table Centre (FD-274) Taking out unserviceable top from table centre and S&F new top made out of pre-laminated particle board one side teak face exterior grade of BWR 18mm thick duly provided with 4mm thick teak wood beading all around the top complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable leg from the table and S&F new leg made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable top rail from the table and S&F new top rail made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

S&F of new bracket of 50mm triangular on two sides shape made out of 25mm thick well seasoned hardwood with suitable size screws as support between rails and (legs set of 08 Nos to each table) all as directed by GE/Engr-in-charge.

Teapoy wooden (FD-232,278 & 34) Taking out the unserviceable top from Teapoy wooden and S&F new top made out of pre-laminated particle board of one side teak face exterior grade BWR type of 18mm thick duly provided with 4mm thick teak wood beading all around the top complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable leg from Teapoy wooden and S&F new leg made out of well seasoned teak wood as per existing shape & size complete including PVC shoes of all four legs to be replaced with new one of superior quality for proper balancing complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable long rail from the Teapoy wooden and S&F new long rail made out of well seasoned teak wood as per existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out the the unserviceable side rail from Teapoy wooden and S&F new side rail made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Table peg (FD-236 & 277) Taking out unserviceable top from table peg and S&F new top made out of pre-laminated particle board one side teak face exterior grade of BWR 18mm thick duly provided with 4mm thick teak wood beading all around the top complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable leg from the table peg and S&F new leg made out of well seasoned teak wood as per the existing shape & size complete. PVC shoes of all four legs to be replaced with new one of superior quality for proper balancing, all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable long rail from the table peg and S&F new long rail made out of well seasoned teak wood as per existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable side rail from the table peg and S&F new side rail made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Table dining 6 persons (FD-239 & 273) Taking out the unserviceable top from table dining 6 persons and S&F new top made of pre-laminated particle board one side teak face exterior grade of BWR type 18mm thick duly provided with 4mm thick teak wood beading all around the top complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable leg from table dining 6 persons and S&F new leg made out of well seasoned teak wood as per the existing shape & size complete including. PVC shoes of all four legs to be replaced with new one of superior quality for proper balancing, all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable long rail from table dining 6 persons and S&F new long rail made out of well seasoned teak wood as per existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable side rail from table dining 6 persons and S&F new side rail made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

S&F of new bracket 100mm triangular on two sides shape made out of 25mm thick well seasoned hardwood with suitable size screws as support between rails and legs (set of 08 Nos to each table) all as directed by GE/Engr-in-charge.

Table dining 8 persons (FD-239, 273 & 376) Taking out unserviceable top from table dining 8 persons and S&F new top made out of pre-laminated particle board one side teak face exterior grade BWR 18mm thick duly provided with 4mm thick teak wood beading all around the top complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable leg from table dining 8 persons and S&F new leg made out of well seasoned teak wood as per the existing shape & size complete including PVC shoes of all four legs to be replaced with new one of superior quality for proper balancing, all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable long rail from table dining 8 persons and S&F new long rail made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable short rail from table dining 8 persons and S&F new short rail made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

S&F of new bracket 100mm triangular on two sides shape made out of 25mm thick well seasoned hardwood with suitable size screws as support between rails and legs (set of 08 Nos to each table) all as directed by GE/Engr-in-charge.

TABLE 900x900mm (FD-30 & 291) Taking out unserviceable top from table 900x900 mm and S&F new top made out of pre-laminated particle board one side teak face exterior grade BWR of 18mm thick duly provided with 4mm thick teak wood beading all around the top complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable leg from table 900x900mm and S&F new leg made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable top rail from table 900x900mm and S&F new top rail made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

S&F of new bracket 100mm triangular shape made out of 25mm thick well seasoned hardwood with suitable size screws as support between rails and legs (set of 08 Nos to each table) all as directed by GE/Engr-in-charge.

Table writing (FD-249,275 & 33) Taking out unserviceable top from table writing and S&F new top made out of pre-laminated particle board one side teak face exterior grade BWR 18mm thick duly provided with 4mm thick teak wood beading all around the top complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable leg from table writing and S&F new leg made out of well seasoned teak wood as per the existing shape & size complete including. PVC shoes of all four legs to be replaced with new one of superior quality for proper balancing, all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable long rail the from table writing and S&F new long rail made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable short rail from the table writing and S&F new short rail made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable centre stiffener from the table writing and S&F new centre stiffener made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable side stiffener from the table writing and S&F new side stiffener made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable shutter from the table writing and S&F new shutter made out of pre-laminated particle board of 18mm thick exterior grade BWR one side teak face duly provided with 4mm thick teak wood beading all around the shutter including piano type hinge continuous, knob & 6 lever brass lock with duplicate keys of best quality complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable back plywood from box of table writing and S&F new back plywood made out of 6mm thick plywood commercial exterior grade of BWR as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable drawers from Table writing and S&F new drawers made out of 12mm thick well seasoned teak wood except bottom of drawers which shall be of 6mm thick ply wood commercial exterior grade BWR including knob etc complete all as shown in drg and directed by Engr-in-Charge.

Table bed side (FD-276,248 & 28) Taking out unserviceable back plywood from table bed side and S&F new back plywood made out of 6mm thick plywood commercial exterior grade BWR as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable shelves from table bed side and S&F new shelves made out of 12mm thick prelaminated particle board exterior grade BWR as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable side from table bed side and S&F new side made out of 18mm thick pre-laminated particle board one side teak face exterior grade duly provided with 4mm thick teak wood beading on front side matching with the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable top from table bed side and S&F new top made out of 18mm thick pre-laminated particle board one side teak face exterior grade on front side as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Side board (FD-26 & 241) Taking out unserviceable top from side board and S&F new top made out of 18mm thick block board commercial exterior grade BWR provided with 4mm thick teak wood beading on front side complete as shown on drg and directed by Engr-in-Charge.

Taking out unserviceable back plywood from side board and S&F new back plywood made out of 6mm thick plywood commercial exterior grade BWR as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable door shutter from side board and S&F new shutter made out of pre-laminated particle board 18mm thick exterior grade duly provided with 4mm thick teak wood beading all around the top as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable drawers from side board and S&F new drawers made out of 12mm thick teak wood except bottom of drawers which shall be of 6mm thick ply wood commercial grade BWR and front which shall be of 18mm thick prelaminated particle board exterior grade duly provided with 4mm thick teak wood beading all around for front part including knob etc. All as shown in drg.

Taking out unserviceable leg from side board and S&F new leg made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Table dressing Gents with mirror FD-230 Taking out unserviceable drawers from table dressing gents and S&F new drawers made out of 12mm thick teak wood except bottom of drawers which shall be of 6mm thick ply wood commercial exterior grade BWR ply & front of drawers shall be made of 12mm thick pre-laminated particle board one side teak face exterior grade BWR including knob etc as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable top from the table dressing gents and S&F new top made out of 12mm thick pre-laminated particle board one side teak face exterior grade BWR as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable bottom from table dressing gents and S&F new bottom made out of 12mm thick pre-laminated particle board one side teak face exterior grade BWR as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable side from table dressing gents and S&F new side made out of 12mm thick pre-laminated particle board one side teak face exterior grade BWR as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable looking mirror from table dressing gents and S&F new looking mirror of 5.5mm thick, free from distortion and other defect duly framed with back 06 mm thick commercial plywood, teak wood beading & vertical support etc. as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Table dressing ladies with mirror (FD-251, 378 & 32) Taking out unserviceable drawers from table dressing ladies and S&F new drawers made out of 12mm thick teak wood except bottom of drawers which shall be of 6mm thick ply wood commercial exterior grade BWR & front of drawers shall be made of 18mm thick pre-laminated particle board one side teak face exterior grade BWR as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable top from table dressing ladies and S&F new top made out of 18mm thick pre-laminated particle board one side teak face exterior grade BWR as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable bottom from table dressing ladies and S&F new bottom made out of 18mm thick pre-laminated particle board one side teak face exterior grade BWR as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable side from table dressing ladies and S&F new side made out of 18mm thick pre-laminated particle board one side teak face exterior grade BWR as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable looking mirror from table dressing ladies and S&F new looking mirror of size 5.5mm thick, free from distortion and other defect duly framed with back plywood of 06 mm thick commercial, teak wood beading & vertical support etc. as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable plain glass and S&F new plain glass shutter of 4mm thick alongwith standard aluminum channels having two ‘U’ shaped channel for sliding as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Chair dining (FD-279 & 223) Taking out unserviceable rear leg from chair dining and S&F new rear leg made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable front leg from chair dining and S&F new front leg made out of well seasoned teak wood as per the existing shape & size complete including. PVC shoes of all four legs to be replaced with new one of superior quality for proper balancing, all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable front or back or side rail from chair dining and S&F new front or back or side rail made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable cane from the chair dinning Supply & re-canning with new cane of 2 mm wide half round as per Godrej pattern as per the existing complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable stiffener from chair dining and S&F new stiffener made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Chair Writing (FD-280 & 250) Taking out unserviceable rear leg from chair writing and S&F new rear leg made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable front leg from chair writing and S&F new front leg made out of well seasoned teak wood as per the existing shape & size complete including. PVC shoes of all four legs to be replaced with new one of superior quality for proper balancing, all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable front or back or side rail from chair writing and S&F new front or back or side rail made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable cane from chair writing Supply & re-canning with new cane 2 mm wide half round superior quality as per Godrej pattern as per the existing complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable stiffener from chair writing and S&F new stiffener made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable hand rest from chair writing and S&F new hand rest made out of well seasoned teak wood matching with the existing shape & size.

Chair Easy (FD-229 & 281) Taking out unserviceable rear leg from chair easy and S&F new rear leg made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable front leg from chair easy and S&F new front leg made out of well seasoned teak wood as per the existing shape & size complete including PVC shoes of all four legs to be replaced with new one of superior quality for proper balancing, all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable back rail upper side from chair easy and S&F new back rail upper side made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable back rail lower side from chair easy and S&F new back rail lower side made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable side rail from chair easy and S&F new side rail made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable stiffener from chair easy and S&F new stiffener made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable hand rest from chair easy and S&F new hand rest made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable cane from chair easy Supply & re-canning with new cane 2 mm wide half round as per Godrej pattern as per the existing complete all as shown in drg and directed by Engr-in-Charge.

STOOL DRESSING CB (FD-282 & 252) Taking out unserviceable leg from the stool dressing CB and S&F new leg made out of well seasoned teak wood including rubber shoe at bottom of leg as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable long rail from stool dressing CB and S&F new long rail made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable short rail from stool dressing CB and S&F new short rail made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable cane from stool dressing CB Supply & re-canning with new cane of 2 mm wide half round as per Godrej pattern as per the existing complete all as shown in drg and directed by Engr-in-Charge.

CHAIR DINING MAP/SPL/LONG BACK (FD/MAP-II/04 & TP) Taking out unserviceable rear leg from chair and S&F new rear leg made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable front leg from chair and S&F new front leg made out of well seasoned teak wood as per the existing shape & size and changing PVC shoes of all four legs to be replaced with new one of superior quality for proper balancing, all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable front or back or side rail from chair and S&F new front or back or side rail made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable cushion seat from chair S&F with new seat made out of 75mm cushion 40 density on 12mm plywood covered with tapestry cloth of approved shade/texture costing not less than Rs 400/- per Sqm All as shown in drg and directed by Engr-in-Charge.

Taking out unserviceable stiffener from chair and S&F new stiffener made out of well seasoned teak wood as per the existing shape & size complete all as shown in drg and directed by Engr-in-Charge.

TABLE COMPUTER VARIOUS SIZE (TP) Taking out unserviceable drawers from Table computer and S&F new drawers made out of 18mm thick prelaminated particle board exterior grade of suitable size of matching shade including replacement of the sliding channel of existing size and pattern and brass lock of 6 levers complete all as specified and directed by Engr-in-Charge.

Taking out unserviceable key board holding unit from Table and S&F new unit made out of 18mm thick prelaminated particle board exterior grade of suitable size of matching shade including replacement of sliding channels of existing size and pattern complete all as specified and directed by Engr-in-Charge.

M&L for preparation of old polished wooden surfaces duly scrapping the old polish completely with chemical/emery paper & cleaning the old surface. Applying polish to get perfect glossy finish duly applying two or more coats of french polish to three seater Sofa set complete all as specified and directed by Engr-in-Charge.

All as per sl item No 152 but for sofa set single seat

All as per sl item No 152 but for Bed with ply top.

All as per sl item No 152 but for Table 900x600x760 with/ without drawers.

All as per sl item No 152 but for Teapoy wooden.

All as per sl item No 152 but for Table peg.

All as per sl item No 152 but for Table dining 6 persons.

All as per sl item No 152 but for Table dining 8 persons.

All as per sl item No 152 but for Table 900x900.

All as per sl item No 152 but for Table Writing.

All as per sl item No 152 but for Table Bed Side.

All as per sl item No 152 but for Side Board.

All as per sl item No 152 but for Table dressing gents.

All as per sl item No 152 but for Table dressing ladies.

All as per sl item No 152 but for Chair dinning.

All as per sl item No 152 but for Chair writing.

All as per sl item No 152 but for Chair easy.

All as per sl item No 152 but for Stool dressing.

All as per sl item No 152 but for chair dinning MAP/Spl/Long back.

All as per sl item No 152 but for Table centre.

M/S Delhi Engineering Co. (BID ID -3375839)

M/S S.K.Electricals (BID ID -3375979)