Construction of Hall and Repair of Toilet block In Ayush wing CHC at Nuh in Nuh Distt. (Re-invited)

Amount

Earth work in excavation in foundations, trenches etc. in all kinds of soil, not exceeding 2 meters depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry in 15 cm layers with compaction, including disposal of all surplus soil as directed within a lead of 30 Mtrs. (HSR 6.6)

Earth Filling under floors with surplus soil excavated from foundation and taken only from outside the building plinth, in 15 cm layers including ramming watering and consolidating lead up to 30 meters. Subject to condition soil Is non plastic. [HSR 6.13(a)].

Dismantling white or coloured glazed tiles (to be carefully removed) (HSR 8.38)

Centering & shuttering for flat surfaces such as suspended floors, roofs, landings, chajjas, shelves etc. inclination not exceeding 25 degree with horizontal. (HSR 9.1).

Cement concrete 1:5:10 with brick ballast 40 mm nominal size in foundation and plinth (HSR 10.34)

Cement concrete 1:4:8 with stone aggregate 40 mm nominal size in foundation & plinth. (HSR 10.39)

Cement Concrete 1:1½:3 with stone aggregate 20 mm nominal size reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centering and shuttering, laid in position, complete in all respect. (10.82+10.95 (a))

Precast cement concrete 1:1½:3 with stone aggregate 20 mm nominal size in Kerbs and the like items, finished smooth with 6 mm thick cement plaster 1:3 on exposed surface including form work, placing and fixing in position, complete at the ground level or in first storey. [HSR. 10.77 + 10.95 (a)]

Precast Factory Manufactured cement concrete 1:1½:3 with stone aggregate 20 mm nominal size in Tiles and Channels the like items, finished smooth with 6 mm thick cement plaster 1:3 on exposed surface including form work, placing and fixing in position, complete at the ground level or in first storey. [HSR. 10.78 + 10.95 (a)]

Cement Concrete 1:1½:3 with stone aggregate 20 mm nominal size reinforced concrete work for walls exceeding 20 cm thickness (straight and curved) beams, girders, stairs, columns (Square or rectangular) battens and lintels etc. excluding steel reinforcement but including centering and shuttering, laid in position complete in all respects. (10.86+10.95 (a))

Cement Concrete 1:1½:3 with stone aggregate 20 mm nominal size reinforced concrete work for walls exceeding 20 cm thickness (straight and curved) beams, girders, stairs, columns (Square or rectangular) battens and lintels etc. excluding steel reinforcement but including centering and shuttering, laid in position complete in all respects. (10.90+10.95 (a))

First class brick work laid in cement sand mortar 1:6 in foundation and plinth. (HSR 11.2)

First Class brick work laid in cement sand mortar 1:6 in First Storey upto 4 metres above plinth level. (HSR 11.7)

Terracing consisting of tiles 22.86 cm X 11.43 Cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and on other layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 kg per sqm on top of R.C.C slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13)

Top khurra 0.6 m x 0.6 m for rain water pipe in 25 mm thick cement concrete 1:2:4 over 50 mm thick cement concrete 1:8:16. (HSR 13.50)

Cement Concrete 1:2:4 gola 10cm x 10cm quadrant along junction of roof with parapet wall finished smooth, where specified. (HSR 13.64)

Providing & Fixing 100 mm PVC Rainwater Pipe 6 kg. pressure of ISI mark in cement mortar during masonry work. (a) 100 mm dia PVC pipe 6 kg. pressure. (Make Supreme, Phinolex, Prince or equivalent). [HSR 13.89(a)].

Providing & fixing PVC Rain water pipe 6 kg. pressure of ISI mark in cement mortar during masonry work (HSR 13.89 (b)) 150 mm dia PVC pipe 6 kg. pressure, Supreme, Finolex, Prince

Providing and fixing PVC Bend ISI mark (HSR 13.90 (b)) 150 mm dia PVC Bend, Supreme, Finolex, Prince

Providing and fixing False Ceiling without grooves with 12mm to 15mm thick, 600mm X 600mm best quality mineral fibre tiles of approved make fixed on M.S. Steel runners frame i/c cost of screws angles, cleats, rawel plugs, with taping and painting, etc. complete in all respects as approved by the Engineer-In-Charge. (HSR 13.92)

Base course of floors consisting of 100 mm thick cement concrete 1:8:16 and 100 mm sand or stone filling. (HSR 14.1)

Kotah Stone Flooring minimum 25 mm thick in any pattern as specified over 20 mm thick base of cement coarse sand mortar 1:3 laid and jointed with neat cement slurry mixed with pigment to match the shade of stone including rubbing and polishing. (HSR 14.62).

Pdg. & fixing ceramic tiles/anti skid tiles of size 400mm x 400mm or above size of approved make in floors, laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Note:-Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT & JOHNSONS. (HSR 14.91)

Providing and fixing vitrified tiles of size 600x600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like: RAK, NITCO, KAJARIA (Double charged tiles shall be used as approved by Engineer in charge. (HSR 14.89) SOMANI, ORIENT BELL, JOHNSON & SIMPLO ETC.

Providing and fixing vitrified tiles of size 600 x 600mm of approved make in skirting / dado laid in any pattern as specified over base of 12mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like: NITCO, KAJARIA, RAK (Double charged tiles shall be used as approved by Engineer in charge). (HSR 14.90) SOMANI, ORIENT BELL, JOHNSON & SIMPLO ETC.

Providing and fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete. (HSR 14.92)

12mm thick cement Plaster 1:4. (HSR 15.5).

12mm thick cement Plaster 1:6. (HSR 15.7)

15mm thick cement plaster 1:6 on rough side of Single or half brick walls. (HSR 15.12)

10mm thick cement plaster 1:4 under side of ceiling. (HSR 15.52).

Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping etc. (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.2).

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.3).

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.58).

Providing two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.79 (b)).

Providing and applying two coats white cement based putty over plastered surface and grindling the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (Note:- reputed make Putty such as J.K./ Birla shall be used as approved by Engineer-in-charge). (HSR 16.81)

Cost of Aluminnium fittings complete for doors and windows, such as tower bolts, handles, etc. and screws for these fittings (excluding sliding bolt) (a) for Single leaf shutter. (Powder coated fittings will be supplied by the deptt. Instead of Aluminium fittings). (HSR 17.72)

Supplying and fixing hydraulic door closer I.S.I mark, with necessary screws etc. complete (b) I.S.I designation no. II (size of door 701 mm to 850 mm) (HSR 17.82(b))

Providing and fixing sliding bolt with nuts & screws etc complete. (b) Aluminium (HSR 17.83 (b)). (i) Size 300 mm x 16 mm.

Factory manufactured wire gauze door and window shutters of commercial hard wood such as hollock, champ, chikrassy annd chaplash, etc. (non coniferous timber other teak conforming to I.S specification no. 1003, kiln seasoned) with 100 mm wide vertical styles, 150 mm wide lock rail 200 mm wide bottom rail, and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc. complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position) (i) 30 mm thick (HSR 17.92 (i) - Note I under 17.18

Factory manufactured solid flush door shutters, with block board core as der I.S. No. 1659-1669 bonded with water, proof type danol formaloehyde synthetic resin, hot-press as , conforming to I.S. 2202 part-I and II fixed in position including iron hinges screws chocks/cleats and stops, etc. (Excluding the cost of any fittings other than specified above, but including labour for fixing the same in position):- (Note) Commercial veneering with vertical grains or cross bands and face vaneer on both sides comercial facing with laminated core and lipped edges. Duro, Green make 25 mm. Thick (HSR 17.93(a) (i) - note I under 17.18)

Factory manufactured solid flush door shutters, with block board core as per I.S. No. 1659-1669 bonded with water proof type phenol formaldehyde synthetic resin, hot-pressed, conforming to I.S. 2202 part-I and II fixed in position, including iron hinges, screws chocks/cleats and stops etc. (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position):- (Note) :- Commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges. 35 mm. Thick (HSR 17.93a iii- note I under 17.18))

Wrought iron and mild steel (using angles flats square bars, tee and channels ladders, grills grafting frames, widows guards iron doors openable or fixed stair case or parapet or any other type of railing gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position (HSR 18.12)

Steel reinforcement TMT steel bar FE-550 EQR/FE-500 D grade or more for RCC work, where no included in the complete rate of RCC including straightening, bending, binding, wastage, overlaps, welded joints, spacer, bars, chairs, stays, hangers and annealed steel wire etc. and placing in the position complete in all respect for all heights/depts/story/ basement etc. (Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing, shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement). (NS)

Pressed steel sheet frames (chowkhats) consisting of 2mm thick steel sheet of the specified section, including iron lugs (hold fasts) iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete. (HSR 18.34)

(b) door and window frame of size 76 mm X 38 mm with 35 mm wide single rebate

(d) door and window frame size 114 mm X 50 mm with 35 mm wide double rebate.

Providing and placing in horizontal layers filtering media screened, washed and cleaned as described below: (HSR 28.50)

(a) Filter media fine graded 1.5 mm to 3 mm

(c) Filter media course Bajri 6 mm to 20 mm

(d) Filter media boulders 50 mm to 75 mm

Boring for hand-pump in clay, fitting strainer and pipe (b) above 75 mm dia bore, but not exceeding 100 mm dia (i) from 0 to 15 meter. [HSR 26.10 (b)].

Constructing brick masonry inspection chamber sizes as given below upto 0.60 metre average depth in cement mortar 1:5 lime concrete with 40 percent limer mortar 2:3 in foundation cement concrete 1:2:4 benching 12 mm thick cement plaster 1:2 with a floating coat of 1 mm thick of neat cement R.C.C. 1:2;4 slab 100 mm thick./C.C. topping 50 mm thick with 455 mm x 455 mm 610 mm inside light duty C.I. inspection chamber cover and frame weight as per I.S.I. specification painted with 3 coats of black bitumastic superior paint coplete as per standard design. (c) Size 600 mm x 900 mm inside (with 455 mm x 455 mm cover and frame light duty singel weighing 20 Kg with R.C.C. slab). [HSR 29.84]. (a) Size 450 mm x 450 mm

Extra for over 0.30 metre depth of inspection chamber. (a) 450 x 450 mm. (HSR 29.85)

Providing and fixing SFRC manhole covers and frames markd with IS: 12592 including setting the same to correct lines and levels in 1:2 cement sand mortar over manhole including carriage loading, unloading stacking, handling, re-handling etc. complete in all respect to the satisfaction of engineer-in-charge. Type: Extra heavy duty set (MD-10) 560 mm clear opening. (HSR 29.94)

Providing & fixing PVC pipe (4kg/cm2) duly slotted IS-4985:1988 including cost of adhesive, carriage, loading, unloading etc. complete in all respects to the satisfaction engineer incharge. Make:- Supreme, Diplast or any reputed make as approved by Engineer-Charge. (i) 160 mm i/d (NS)

Providing and fixing Steel bar embedded plastic steps of size 263 mm x 165 mm of orange colour, conforming to specifications, in pump chambers, manholes etc. having minimum 3 mm thick Polypropylene polymer confirming to IS : 10910 encapsulated on 12 mm dia ribbed steel bars per IS : 1786. (NS).

Earth work non plastic under floors with good earth taken from outside of campus area with all lead and lift including loading, unloading, laid in 15 cm layer including ramming, watering, consolidating, compaction, and compensation of earth etc., complete in all respect as per the direction of engineer in charge. (For any lead and lift). [NS ITEMS].

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE EUROPEAN TYPE WATER CLOSET SUITE WITH CONCEALED ‘P’ or ‘S’ TRAP with or without vent (as approved by the Engineer-in-charge) and all other necessary fittings as fully described in item no. 30.3 above (i) White. (HSR 30.6 (i)

Providing and fixing in position best Indian make (to the approval of the Engineer-in-charge). Indian type orissa or orya water closet suite for sinking into floor, with raised foot treads complete with 100mm H.C.I. ‘P’ Trap with or without vent as required and all other necessary fitting as fully described in item No.30.1 Above (HSR 30.2)

Extra over item nos. 30.3 to 30.6 for providing and fixing best Indian make plastic hygienic seat with lid complete instead of hollow black or white plastic seat and lid. (HSR 30.13). i) white plastic seat (solid)

Proving and fixing in position best Indian make lavatory suites consisting of. (HSR 30.41) (iv) Size 550mm x 400mm with one no. Tap

Proving & fixing in position 32mm dia G.I. waste pipe embedded in wall or lead waste pipe (weighing 3.47kg. per metre and 2.8 mm thick) upto floor level including cost of wipped solder joints complete (as required by the Engineer-in-Charge). (HSR 30.48)

Providing & fixing in position best Indian Make beveled edge 5.5 mm thick mirror asbestos ground fixed in position by means of 4 Nos. chromium plated brass screws And washers complete including cutting and making good the walls etc. Indian make. (HSR 30.71). a) 600mmx450mm

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the Engineer-in-Charge). (HSR 30.75)

Bib cock long body

Bib cock

Prov. and fixing in position best Indian make flexible tube connection. (HSR 30.82) (b) C.P. brass. i) 15mm x 300mm

Providing and fixing HDPE water storage tank of Sintex, Diplast, O.K., Supreme make with covers. Lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plus on scour pipe including cost of nipples, washesrs, flanges for connections in tanks complete in all respects to the satisfaction of Engineer-in-Charge (except civil work) (HSR 30.119) 1000 Ltrs.