Lake Front Development at Ayanambakkam Chennai

Amount

Pile Works

Labour Charges for Boring and installing cast insitu encasing piles on lake bed resting on hard strata with N value more than 100 (using DMC method) of size 450mm diameter, including necessary reinforcement as given in drawing, of basic length measured from under side of pile cap to the tip of pile shoe by adopting M25 grade and reinforcement as in drawing and 8mm diameter stirrups at a spacing of 200mm c/c. However, payment will be made on the basis of work done.The work includes dewatering,Bentonite slurry process,pile muck removal,casing for stabilization of pile bore,flushing of pile bore,welding of reinforcement if necessary,Slush removal,cleaning and the protection of surface water.

Providing And Laying In Position, Standarded Concrete Mix M-30 Grade In Accordance With Is:456-2000, Using 20mm And Down Graded Hard Broken Granite Stone Jelly For All Rcc Iterns of Works With Minimum Cement Content of 350 Kg/M3 And Maximum Water Cement Ratio of 0.50, Including Admixture (Plastidser Super Plastidser)In Recommended ProportionsAs Per Is 9103 to accelerate, Retard Setting of Concrete, Improve Workability Without Impairing Strength And Durability With About (5.0 cm.) 7730 Kg. of 20mm Machine Crushed Stone Jelly And With About (3.3 Cu.m.) 5156 Kg. of 10-12mm Machine Crushed Stone Jelly And With About And With About(4.79 Cu.m.) 7670 Kg of Crushed Stone Sand (M Sand), But Excluding Cost of Reinforcement Grill And Fabricating Charges, Centering Shuttering And Also Including Laying, Vibrating With Mechanical Vibrators, Finishing, Curing and including pumping charges Etc. And Providing Fixtures Like Fan Clamps In The Rcc Floor/Roof Slabs Wherever Necessary Without Claimin Extra ,Etc., Complete Complying With Standard Specification And Des Alimentarer Over He Departmental Officers, The Coarse Und Die Aggregates To Be Used Should Comply With The Requirements That Is Standards (No Separate Payment Will Be Made By The Department For The Excess Usage of Materials)

Supplying and fabricating EPOXY Coated STEEL including cutting, bending hooks, cranking, fabricating, assembling and laying in exact position,typing with soft steel wire 16 gauge ,etc., complete conforming to BIS std.

Carrying out Initial working pile load test on the Specified dia piles as specified in IS 2911(part 4) includes all machinery, instruments, measuring devices platforms and kentledge pile caps etc., dismantling and carting away entire setup, excavation and dewatering etc., all complete - 450mm dia Pile - Safe load upto - 32MT

Carrying out Dynamic load pile test on the Specified dia piles as specified in ASTM D4945 for specified load test includes all machinery, instruments, measuring devices platforms and kentledge pile caps etc., dismantling and carting away entire setup, excavation and dewatering etc., all complete - 450mm dia Pile

Civil Works

Earth Work Excavation and deposting on banks with initial lead of 10m and initial lift of 2m in hard stiff clay stiff black cotton soil, hard red earth, shales, muram, gravel, stony earth and earth mixed with small boulders etc., as per SS 20B excluding hard rock requiring blasting etc., complete in all respects complying with relevent standard specifications and as directed by departmental officers.

Refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification

Supply and filling Rubble soling in foundation and basement as per requirement

Supplying and filling in foundation, basement, etc with filling crushed stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation and basement with conveyed earth in layers of not more than 15cm.thick well rammed watered and compacted etc., complete complying with standard specification.

Plain Cement concrete work 1:4:8 (1 cement, 4 Crushed Stone Sand (Commercially called M-Sand) and 8 blue granite broken stone jelly 40mm gauge) including consolidation curing, etc. complete for foundation, etc. upto basement

Supplying and erecting centering for sides and soffits including supports and shuttering upto 3m high for plane surface such asRCC circular coloumn using mild steel sheets of size 90x60cm,10gauge stiffened with welded mild steel angles of size 25x25x3mmfor boarding laid over silver Oak(country wood) joists of size10x6.5cm spaced at about 90cm centre to centre and supported bycasuarina props of 10 to 13cm dia spaced at 75cm centre to centreetc.,complete

Circular Column/Pond

Foundation

Plinth Beam

Column

Beam/Slab

Curved Surfaces

Providing And Laying In Position, Standarded Concrete Mix M-30 Grade In Accordance With Is:456-2000, Using 20mm And Down Graded Hard Broken Granite Stone Jelly For All Rcc Iterns of Works With Minimum Cement Content of 350 Kg/M3 And Maximum Water Cement Ratio of 0.50, Including Admixture (Plastidser Super Plastidser)In Recommended ProportionsAs Per Is 9103 to accelerate, Retard Setting of Concrete, Improve Workability Without Impairing Strength And Durability With About (5.0 cm.) 7730 Kg. of 20mm Machine Crushed Stone Jelly And With About (3.3 Cu.m.) 5156 Kg. of 10-12mm Machine Crushed Stone Jelly And With About And With About(4.79 Cu.m.) 7670 Kg of Crushed Stone Sand (M Sand), But Excluding Cost of Reinforcement Grill And Fabricating Charges, Centering Shuttering And Also Including Laying, Vibrating With Mechanical Vibrators, Finishing, Curing and including pumping charges Etc. And Providing Fixtures Like Fan Clamps In The Rcc Floor/Roof Slabs Wherever Necessary Without Claimin Extra ,Etc., Complete Complying With Standard Specification And Des Alimentarer Over He Departmental Officers, The Coarse Und Die Aggregates To Be Used Should Comply With The Requirements That Is Standards (No Separate Payment Will Be Made By The Department For The Excess Usage of Materials) (If pumping of Concrete is required

Foundation Level

Ground Floor Level

Supplying and fabricating MS Steel including cutting, bending hooks, cranking, fabricating, assembling and laying in exact position,typing with soft steel wire 16 gauge ,etc., complete conforming to BIS std.

SOLID BLOCKS 40X20X20 CM Supplying and fixing Solid Blocks of following size confirming to S.S. 2145-1965 (including jam blocks closers etc.) made in CC 1:3:6 (One Cement Three Sand and Six HBSJ 6 mm) in CM 1:5 (one cement and five sand),for masonry wall partition wall including curing neat finishing etc. complete

SOLID BLOCKS 40X10X20 CM Supplying and fixing Solid Blocks of following size confirming to S.S. 2145-1965 (including jam blocks closers etc.) made in CC 1:3:6 (One Cement Three Sand and Six HBSJ 6 mm) in CM 1:5 (one cement and five sand),for masonry wall partition wall including curing neat finishing etc. complete

Brick work in Cement Mortar 1:5 using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-1/4" for foundation and basement including curing, etc., complete complying with standard specifiction.

Special Ceiling Plastering with cement mortar 1:3,10 mm thick in all floors including cost and conveyance of all materials to site and labour charges etc, complete as per standard specifications (S.I.306)

Plastering with Cement Mortar 1:5 (One cement and Five Crushed stone sand ), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Supplying & fixing the floor with Double charges Vitrified tiles of approved quality, colour and design joint free of Size 600mm x 600mm x 8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (one cement three sand) 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officers. The colour & quality of tiles should be got approved by the Executive Engineer before use on work.

Flooring with following Designed antiskid ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadoing walls with following best approved quality, white / colour Glazed tiles of approved sizes set in Cement Mortar 1:2 (One Cement and Two M.sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.600x300x10mm thick

Pre-Painted Galvanized Iron Fixed Louvered Ventilators with Glass and Grill: Providing and fixing louvered ventilator fabricated from roll formed sections made of galvanized steel colour coated / powder coated (Base steel as per IS 513 'D' quality, galvanized as per IS 277 with zinc of 120 grams / sqm.) with total coated thickness of 0.58mm. Paint specification: Coated sections should be with primer coat of epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns. Dimensions of sections: The section for external frame should be of 57mm x 33mm. Fixing details: The section should be cut to length, joined with profile to profile component. Accessories: Glass holding flanges made of glass filled nylon. Glass: Louvers should be provided with 4mm pinhead glass. Grill: Ventilator should be provided with grill made of 10mm Square MS bars to 12mm x 5mm flat at 4" intervals. Total grill unit should be powder coated and fixed to ventilator frame with screws. The above frames should be fixed to brick / concrete masonry walls and floor by means of self-expanding screws.

Supply and fixing of Aluminum Flush door etc, complete as per standard specification.

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Weathering Course with Concrete Broken Brick (S.I.No.278) & ( P & D) Data 54.Jelly 20mm gauge in pure slaked lime (no sand to be added) over roof slab, the proportion of brick jelly to lime being '32 to 12.5 well beated with wooden beaters for giving required slope and thickness as directed by the departmental officers etc., complete.-10 cum

Finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in Cement Mortar 1:3 (One Cement add three sand) 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete

Supplying & fixing the floor with River washed stone75mm thick 60mmX45mm size including fixing in cement mortar as directed

Supply & laying of Tremix Concrete using MS channel as directed

Screed Concrete 1:1-1/2:3 (One Cement, One and a half crushed stone sand and Three hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with Cement Mortar 1:3 (One Cement and Three crushed stone Sand) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers

Seating - RCC Supplying, erecting and Fixing precast reinforcement bench with back rest. Bench shall consist of 2 nos. L shaped bases support in natural cement color of thickness 100mm, back height 1000mm, front height 450mm, base width 620mm and 5Nos Reinforced Concrete planks in red color and size of 1500x100x50mm and 1no. reinforced concrete plank of 150x200x50mm: manufactured by using M?30 grade concrete & reinforced suitably: all parts to 1 No 9994.60 9994.60 9994.60be joined with galvanized nuts and bolts of suitable size As per Park SOR - PD 1890

Providing and laying WPC Flooring of size 2800X150X25mm as per requirement.

Providing and Fixing of polyurethane foam for Sloped roofas thermal insulation panels or Sandwich insulated panels with external 0.50mm total coated thickness pre painted Galvalume sheet with trapezoidal roofing profile having crest height of 38mm at every 333mm span , whereas internal 0.50mm total coated thickness pre painted galvanized iron sheet with micro ribbed profile and the insulation material will be chlorofluoro carbon and hydro chlorofluoro carbon free , high performance rigid polyurethane foam (PUF) conforming to IS 12436 having density not less than 40±2Kg/M3, Thermal conductivity (K-Value) 0.024 W/m.K measured at 10 degree C mean temperature along with necessary flashings such as L flashing, C flashing etc& accessories such as screws ,fastners ,sealants etc for fixing the panel etc., complete complying with standard specification.

Providing And Fixing All Side Machine Cut Granite Stone Using 0.75M Height 0.100M Thick And 1.0M Length Granite Stone Without Fragmentation For Centre Median Including Cost And Conveyance of Granite Kerb From Available Source To Work Site Including Labour Charges For Fixing The Granite And Pointing With cm. 1:3 And All Other Incidental Charges Etc. Complete

STRUCTURAL STEEL WORKS: Supplying fabricating, hoisting, erecting and fixing in position Mild steel structural steel works of Pergola, Gate for compound wall and grill at all elevations, levels and heights including aligning, levelling, providing and fixing bolts, nuts, washers, comprising MS plates, flats, squares etc., of various sizes and other structural steel sections conforming to latest IS2062 Grade - A&B including straightening, cutting, welding, bending to shape, bolting and inclusive of the following finishes. The rate including cost of all materials, labour changes, scaffolding, stagging, transportation, lead & Lifts, wastage, etc., complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge. All MS members shall be painted with one coat of zinc chromite primer and 2 Coats of 35 microns DFT of synthetic enamel paint of approved colour and make etc,. The rate includes the cost of all materials, labour, tools, tackle and plants, wastage etc., as per specification and drawings complete. The rate quoted is to include cost of bolts, nuts, washers, welding, electrodes and connections required for the work. No extra on this account will be paid for. The rate to include preparation of fabrication shop drawings for owner's approval:

Supplying & Erection in position of Structural Steel sections : Providing and fixing in position Hot rolled structural steel Members / Sections consists of MS joists, channels, angles, purlins, pipes, hollow tubes, runners, insert plates, flats etc. at all levels. Surface preparation of all MS members by Sand blasting to SA 21/2 grade and painted with anti corrosive, low VOC PU paint (metallic finish) with compatible primer to a minimum film thickness of 75 microns and 2 coats of low VOC PU paint of Akzonoble make and total dry film thickness 225 microns. (Only Main structural supports related to Facade works if required any shall be considered and no base frame or support structure shall not be considere, which shall form part of the respective cladding and Glazing items). Refer Particular Specification for Mode of measurement for this item. The rate including the cost of all materials,labour,tools,tackle and plants, wastage etc.,as per specification and drawings complete. The rate including cost of bolts, nuts, washers, welding, electrodes and connections required for the work. No extra on this account will be paid for. The rate to include preparation of fabrication shop drawings for departmental engineer-in-charge approval before commencement of work.

Providing and Applying two component flexible polymer modified acrylic cementitious waterproofing coating with a mix ratio of (5 Liquid :7 Powder) to the RCC surface of the STP tank applied @ 2.2kg/m2 in 2 coats to achieve 1.2mm DFT, having Elongation at break >120% as per ASTM D 412, Tensile strength >1N/ mm2 as per ASTM D 412, Adhesion strength: 0.80N/mm2 as per ASTM D 4541, crack bridging upto 2mm as per ASTM C 836. The finished cost to include surface preparation, making coving of 50 mm X 50mm at all right angles of wall Junction with Polymer Repair Mortar and lay 45 gsm glass fibre mesh over the angle fillet when the first coat in still wet, treatment of cracks completely as per specification. Followed by applying 15 mm thick dimensionally stable fibrous reinforced cementitious structural grade dual shrinkage Polymer Mortar on as protective plastering @ 29kg/m2. The material having Compressive strength of 38 MPa at 28 days as per EN 12190, Adhesive Bond Test, >1.5 Mpa as per EN 1542, followed by Water curing by sprinkling water for 3 times a day for 5- 7 days. followed by applying two component coal tar epoxy-based coating on inside surface of Sewage & Effluent treatment tank @ 0.30 kg/m2 in 2 coats to achieve a DFT of 200 microns when fully cured. Ensure that this coating is applied over the protective plaster. The material shall have Scratch resistance, for 7kg load as per ASTM : D 7027 - 05, Chemical resistance, immersion in dilute acid alkali & salt solutions – 7 days confirms to ASTM : C 868, Salt Spray resistance confirms to ASTM : B 117.

Pavers

Supply and Fixing of 83mm - Paver Type II over quarry dust cushioning as per the drawing. The cost of Quarry dust will not be paid separately. The rate shall be inclusive of all lead, lift etc complete and as per the instructions of EIC

Supplying And Fixing of Rubber Moulded Grey Premium Concrete Kerb of Size 450X125X300mm Using M30 Concrete. The Concrete Shall Be Moulded By Table Mount Vibrated With Polypropylene Fibers At 5% And Curing Compound. The Rate Shall Include Cost of Materials, Transportation, Loading & Unloading Charges And including Necessary Earth Work Pointing With cm. 1:3 To Full Depth Curing Thread Lining etc., completed as standard specification and as directed by the engineer-in-charge.AS PER GCC BRR 2022 - 2023, S.No:74, Sch.No:BRR GPC (RM)K

Supply and Fixing of Cobble stone flooring. The rate shall be inclusive of all lead, lift etc complete and as per the instructions of EIC

Landscape Works

Supply & stacking of red earth at site to the departmental guage for pre-measurements which is of light textured, crystalline, porous and friable and not of generally acidic or neutral but not of alkalineand should be fertile, including seignior age charges, cost of transportation, loading, unloading, stacking and inclusive of all taxes etc., complete.

Supplying and planting Shrubs with Bushy cost including material, labour and transport charges etc., complete.

Pennisetum alba

Tabernae montana

Jatropha

Ixhora White

Tabemae montana dwarf

Tecoma Yellow

Ixhora Red

Ixhora dwarf yellow

Justica adhatoda

Alternanthera sessilis white

Raphis Excelsia

ophiopogan japanicus

Helicona lady di yellow

Canna red

Alpina Zerumbeta

ophiopogan japanicus (long)

Canna varigated

Helicona lady di

Crossandra Red

Boston fem

Spider Lilly narrow

Canna yellow

Canna white

Rohio

Crossandra yellow

Spathophyllum

Heliconia Psittacorum

Asparagus Densiflora

Statchitarpheta mutabius

ophiopogan japanicus varigated

Alternanthera sessilis red

Ipomia batata

Canna Pink

Sanchiza speciosa

Costus woodsoni

Philodendron Sellom

Areca Palm Dypsis

Ficus Lytara

Painted Bamboo

Dracena Marginata

Dracena Fragrans

Kenita Palms

Areca Palm

Dypsis lutescana

Alpinia purpureta

Buddha Belly Bamboo

Pgmy date palm

Cordyline fruiticosa

Licula Grandis

Cymbopogon citratus

Cordyline tricolor

calathuea lutea

Helicona Rosatara

Ficus Benjamina

Tecoma gaudichi

Bambusa multiplex

Dsaoxylum lineare

Peace Lilly

Bird nest fern

Calaodium

Statchitarpeta

Colocassia

Pandanus

Colocassia black

Tecoma Stans

Nerium Oleander Pink

Plumeria alba

Nerium Oleander White

Codium Varigatum

Eugenia

Helicona Lady di Varigated

Cordyline Fruiticosa Pink

Tecoma Stans Red

Supplying and planting Trees with height of 6' cost including material, labour and transport charges etc., complete.

Swetenia Manogany

Terminalia Arjuna

Samaneasaman

Terminalia Mentalis

Bahunia Purpurea

Cacosnufia

Pogamania Pinata

Delonix Regia

Skeleton Tree

Fish Tail Palm

Ficus Religosa

Areca Nuts

Cordia Dihtoma

Ficus Bengalis

Syzygin Cumini

Calophylum inophylum

Jackfruit Tree

Ficus racemosa

Borassus Flabelifer

Tamarindus indica

Azadirchta indica

Thespesia Populnea

Indian Date Palm

Cassia fistula

Cathatanthus Roseus , indian oleanderq

Bottle Gourd Colocasia, yam

Erythrina Indica

Spathudia campunulam

Peepal

Nili gulmohar

Pink trumpet

Bahunia

Supplying and Laying Lawn cost including material, labour and transport charges etc.,complete.

Preparation of Mounds of various size and shape by availlable excavated/ Supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer - in - charge.

Maintenance of lawns: Lawn mowing with electric motor / portable cutter machine and edging & weeding of the lawns (once in 15 days from June - Nov and once in 30 days from Dec - May) with watering 10 to 15 ltrs /per Sqmt/per day basing on season and weather conditions (30 watering is required in a month to maintain sub-soil moisture continuously), application of fertilizers, insecticides, Fungicides (once in a month) by manual excluding cost of fertilizers & water.

Maintenance of shrubs, other ornamental foliage, foliage planting and Trees planting including watering, weeding, application of fertilizers and pesticides, trimming etc for One month 1 Sq.m/ Month

Electrical

CT Metering Panel - Supply, Installation, Testing and Commissioning of CPRI approved make of panel, cubicle type, Free standing, floor mounted, single front, 14 SWG CRCA sheet steel, enclosed separate compartment for each feeder, front operated, Powder coated, indoor type dust and vermin proof, hinged lockable doors, complete with electrolytic grade copper bus bars, internal wiring, colour coding, ferrules, Panel mounting MS Channels, fasteners, etc., including all associated control wiring. 1set of 200/5A CT with TNEB Metering provision and 1nos of 200/5A CT for APFCR .

200A Isolator Panel - Supply, Installation, Testing and Commissioning of CPRI approved make of 200A TPN MCCB panel, cubicle type, Free standing, floor mounted, single front, 14 SWG CRCA sheet steel, enclosed separate compartment for each feeder, front operated, Powder coated, indoor type dust and vermin proof, hinged lockable doors.

Fabrication, Supply, Erection, Testing and Commissioning of whether proof CRCA sheet steel made up of 2mm powder coated MCCB Indoor Type Three Phase Changer Over panel of size (H 1450 X L 1400 X D 400 ) mm with suitable to accommodate 200A 4 pole Three phase Change Over Switch-1No. as incomer for EB Source and as incomer for DG Source , 1no 160A 4Pole MCCB, 6nos of 125A 4Pole MCCB, and 2nos of 63A 4Pole MCCB's, compartment for as O/G supply with the provisions to accommodate Busbar chamber and cable chamber with size of 33x6mm copper busbar 4 runs having three phase Multifunction meter with line indicators and with all necessary accessories with all other connected works etc. The panel made up of 16/18 SWG CRCA sheet steel comprising of 4 sections with separate sheet steel weatherproof and shock proof safety insulation system conforming to IE Rules with IP protection, and with the panel should be painting by powder coating finishing etc.,as complete and making good of the panel with neat finishing. (Switch make : L & T / ABB) panel should be earthing confirming ISI specifications. The panel should be erected on Anchor fastners, bolts and nuts for mounting the Indoor Panel as directed by engineer-in charge/department superior engineers. Including Bus bar support, Cost of Weldding charges for mounting the panel, Rotary Handle, Spreader Terminal, Multifunction Meter digital type / MFM 5010 LED meter CI 0.5S

VERTICAL THREE PHASE MCB DISTRIBUTION BOARD WITH MCB : Supply and fixing of 84way vertical TPMCB sheet steel Industrial Type TPMCB DB with IP54 Protection of surface type fitted with bus bars and neutral links with1 No. of 100A FP MCB as Incoming and 12 Nos.of 32A,10KA Triple Pole MCB in Flush with wall and making good of the concealed portion with earth connection.( Industrial Type TPMCB DB with IP54 Protections)

Supply and fixing of 7 segment 8 way 63A TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and separate 4 way provision for accommodating one no. 4 pole incoming 63 A TPN MCB, 10kA, / Isolator and another separate 4 way for accommodating one no. 63 Amps, 30 mA, 4 pole ELCB / RCD (totally 8 ways in one segment) and 24 nos 6-32 A, 10kA, SP MCB / Isolators ( totally 24 nos.) for outgoing in 3 segments with label holder and provision for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only.

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 25A FP ELCB switch as incoming and 4 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Higher End

Supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonry pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 48W LED Street light fitting with LED (Higher end) with 1 metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED street light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour

Supply and Fixing of 40W 4' LED Tube Light with PVC unsheathed copper leads from terminals to the fitting. (Make : Philips/Crompton/Havelles )

Supply and fixing of 1200mm (48") sweep AC ceiling fan 5 star rated complete ( Higher end) with 2 module 100W fan step regulator (Higher end) with 2.5 metre down rod with fan clamp, and wiring to the near by point with 1.5 sqmm FRLS , PVC insulated copper wires, including necessary accessories and hardware's as required.

Supply and fixing of 300mm(12")sweep (Heavy duty) AC Exhaust fan complete with necessary wall opening and making good of the wall and wiring to the near by point with 1.5 sqmm FRLS PVC insulated copper wires including necessary accessories and hardware's as required.

Supply and fixing of louvers shutter arrangements for 300mm(12")sweep (Heavy duty) AC Exhaust fan complete

Supply and Fixing of Cove LED Light (10W) on floor or Ceiling with Mounting accessories ( IP20 & IP44 ) Complete etc,. (Make :Philips/ Klite /Crompton/Havelles )

Supply and laying of following XLPE armoured LTUG cable in a trench/Tray with suitable cable tie tag etc as required.

Supply and laying of 31/2 core 120 Sq.mm PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Laying of 3 1/2 x 95 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Laying of 3 1/2 x 70 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Laying of 3 1/2 x 50 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Laying of 3 1/2 x 35 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Laying of 31/2 x 25sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Laying of 4C x 16 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Laying of 4C x 6 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Laying of 4C x 4 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Laying of 3C x 2.5 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supplying & Laying HDPE Pipe as per requirements including excavation & refilling.

Supply and fixing of double compression brass cable gland for following Aluminium conductor XLPE insulated armoured cable of 1100 V grade with earth connection.

Supply and fixing of brass cable gland for 3 1/2 C x 120 Sq.mm PVC LTUG armoured cable with earth connection

Supply and fixing of brass cable gland for 3 1/2 C x 70 Sq.mm PVC LTUG armoured cable with earth connection

Supply and fixing of brass cable gland for 3 1/2 C x 50 Sq.mm PVC LTUG armoured cable with earth connection

Supply and fixing of brass cable gland for 3 1/2 C x 35 Sq.mm PVC LTUG armoured cable with earth connection

Supply and fixing of brass cable gland for 3 1/2 C x 25 Sq.mm PVC LTUG armoured cable with earth connection

Supply and fixing of brass cable gland suitable for 4C x 16 PVC armoured LTUG cable with earth connection.

Supply and fixing of brass cable gland for 4C x 6 sqmm COPPER cable LTUG cable with earth connection.

Supply and fixing of brass cable gland for 4C x 4 sqmm COPPER cable LTUG cable with earth connection.

Supply and fixing of brass cable gland for 3C x 2.5 sqmm COPPER cable LTUG cable with earth connection.

Supply and providing cable end termination of the following size PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (copper sockets for copper cables and Alu. Sockets for alum. Cable)

Supply and providing cable end termination of 3 1/2 Core x 120 Sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete.

Supply and providing cable end termination of 3 1/2 Core x 70 Sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete.

Supply and providing cable end termination of 3 1/2 Core x 50Sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete.

Supply and providing cable end termination of 3 1/2 Core x 35Sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete.

Supply and providing cable end termination of 3 1/2 Core x 25Sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete.

Supply and providing cable end termination of 4 C x 16sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping with electrical connection complete.

Supply and providing cable end termination of 4 X 6 Sqmm PVC LTUG Copper cable with necessary copper cable sockets by crimping etc, with electrical connection complete.

Supply and providing cable end termination of 4C X 4 Sqmm PVC LTUG Copper cable with necessary copper cable sockets by crimping etc, with electrical connection complete.

Supply and providing cable end termination of 3C X 2.5 Sqmm PVC LTUG Copper cable with necessary copper cable sockets by crimping etc, with electrical connection complete.

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 6A one way module switch and 1 no. 6A 3/2 pin module socket with module front plate with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with painting of suitable colour for concealed PVC pipe Plug point ( 8 points / Coil) Higher End

Wiring with 2 x 4 sq.mm. (56/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 16A one way module switch and 1 no. 16A 3/2 pin module socket with module front plate with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with painting of suitable colour for Concealed PVC pipe power Plug point ( 8 points / Coil) Higher End

Supply and Run of 4 of 6 sq.mm. (84/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire with painting of suitable colour.

Supply and Run of 2 of 4 sq.mm. (56/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour.

Supply and Run of 2 Run x 2.5 sqmm and 1R of 1.5sq sqmm PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable Pvc conduit pipe on concealed wall and ceiling with continuous earth wire connection with painting of suitable colour.

Supply, Installation, testing & erecting of 12-18W LED up side light made of pressure die cast aluminium housing with supreme powder coating technology for path light application with IP54 protection. (FOR EXTERNAL LIGHT) Equivalent to BAJAJ, WIPRO & LIGHTING TECHNOLOGIES.

LED Bollard fittings of minimum height 600 mm & dia.100mm having polycarbonate clear/milky diffuser mounted on 3mm thick aluminium finished powder coated pipe with base plate 160x160mm with erection by M8x75mm fastner with required RCC foundation.IP65 for 9 to 20 watt ,surge-4kv- cat-II

Under Water Light,12V DC including Driver,IP-67 with die-cast/deep drawn housing with impact resistance clear toughened glass.

Supply and fixing of thermoplastic loop - in and loop out boxes with lid of dimension min 104X104X70MM with 20A connector. shorting link 2 way necessary and along DIN rail terminal block. The Junction Box shall be insulated and made out of high grade thermoplastic. The JB shall be IP Rated for outdoor applications, environment friendly, recyclable, UV resistant, halogen & silicon free, anti acid& anti corrosive. The JB shall be rated for Degree of Ingress Protection IP 65 in accordance with IEC 60529.

Supply and fixing of 1no.6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Scope cover wall cutting , grouting , flushing and making good on the wall. Higher End.

Supply and fixing of 2nos.6A two module 5 pin socket , 2 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Scope cover wall cutting , grouting , flushing and making good on the wall. Higher End.

Supply and fixing of manufacturer's GI metal back box and 3 nos of 6A modular switch, 3nos of 6A 3 pin combined modular type wall socket in flush with wall mounted on poly carbonate front plate with switch mounting metal parts, in flush with wall.

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Scope cover wall cutting , grouting , flushing and making good on the wall. Higher End.

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 50mm and 2 mtr long earth electrode of low carbon steel rod with 100 micron bonding and 25 kgs of carbon based environment friendly backfill compound and suitable clamp and with copper earth plate of size 125mm x 50mm x 6mm with necessary funnelling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Supply, Installation, Testing and Commissioning of earthing station consisting of 600 x 600 x 3 mm. thick, copper Plate earth electrode, back filling with alternate layer of charcoal, salt, brick masonry work for chamber 450 x 450 mm. heavy duty CI cover, watering pipe, funnel and earthing conductor as per IS:3043 specification. All civil works required such as excavation in all types of soils, rocks, PCC Earthing Chamber foundation, reinstatement and making good the surface to match original, removal of surplus earth etc. are included.

Coil earth to street light poles with No.8 SWG GI wire of 11.5 metres of length in which 10 metres of total length compressed in to a coil of one meter length (75mm to 100mm dia) connected suitable with hexagonal earth bolt of size 8mm in to 25mm welded on the pole at one end with a coil position fixed on the earth.

Supply, fabrication, of GI /Copper earth flat of following size in provided trench, clamping in wall, ceiling, with suitable Clamps/ saddles, connecting the joints through bracing / welding covering with termination in the earth pits, Panels, Distribution boards and equipments with bitumen paint including accessories wooden plugs, screws, fastener etc., all inclusive

Supply and run of 25mm x 6mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection

Supply and run of 25mm x 6mm GI flat with necessary clamps / supports on wall / floor / ground for earth connection

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection

Supply and Run of 1 of No.8 SWG GI wire in suitable PVC rigid pipe on wall / floor / ground for earth connection

Supply and Run of 2 of 10 sq.mm. (140/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with painting of suitable colour.

Supply, Installation, Testing and commissioning of 40 channel 8 SATA NVR, with 6T Hard Disk Drive 4 nos, New logical and visualized GUI design Dual-OS design to ensure high reliability of system running, ANR technology to enhance the storage reliability when the network is disconnected, Configurable normal or hot spare working mode to constitute an N+1 hot spare system Video Input and Transmission, Connectable to the third-party network cameras Compression and Recording, H.265+ compression effectively reduces the storage space by upto 75%, Full channel recording at up to 12MP resolution HD Video Output  HDMI1 / VGA1 outputs provided  HDMI1 Video output at up to 4K ( 3840 × 2160 ) resolution Storage and Playback, Upto 16 SATA interfaces and 1 eSATA interface for HDD connection, Support upto 10TB capacity for each HDD, Smart search for efficient playback. and smart playback to improve the playback efficiency, Supports VCA search for fire/ship/temperature/temperature difference detection triggered video files, POS information overlay on live view and playback, POS triggered recording and alarm Network & Ethernet Access  Hik-Connect for easy network management, 2 Gigabit Ethernet network interfaces.

Supply, Installation, Testing and commissioning of 16 channel NVR with 4TB HDD * 4nos, Up to 20-ch 8 MP IP cameras can be connected, Connectable to the third-party network cameras Compression and Recording, H.265+ compression effectively reduces the storage space by up to 75%, Full channel recording at up to 12MP resolution HD Video Output  HDMI1/VGA1 outputs provided  HDMI1 Video output ) resolution Storage and Playback, Up to 4SATA interfaces and 1 eSATA interface for HDD connection, Support upto 6TB capacity for each HDD, Smart search for efficient playback. (Make: Hikvision/Dahua/Panasonic)

Supply of 8MP, Internet Protocol fixed BULLET CAMERA with following specification: ●1/2.5" Progressive Scan CMOS, ● 3840 × 2160 @15 fps,2.8/4 mm fixed lens,01 lux @ (F1.2, AGC ON), 0.028 lux @(F2.0, AGC ON), 0 lux with IR, H.265+, H.265, H.264+, H.264, 2 Behaviour analyses ( Line crossing detection, intrusion detection) ● Face Detection ● 120dB WDR, ● BLC/3D DNR/ROI, IP67 complied ●On-board Storage - Built-in micro SD/SDHC/SDXC card slot, up to 128 GB, ● Shutter Speed 1/3 s to 1/100,000 s, ● 3-Axis Adjustment Pan: 0° to 360°, tilt: 0° to 100°, ● rotate: 0° to 360°, 2.8 mm, ● horizontal FOV: 102°, vertical FOV: 53°, diagonal FOV: 124°, ●Lens Mount M12 ● IR Range I5: up to 50 m, ● Image Settings Rotate mode, saturation, brightness, contrast, sharpness adjustable by client software or web browser, ● Power Consumption and Current-12 VDC, 0.7 A, max. 7.5W PoE: (802.3af, 36V to 57V), 0.3 A to 0.2 A, max. 9W ● Camera out fitted with metal housing so as to prevent the lens from damages during physical abuse. All including suitable camera stand and accessories. (Make: Dahua/Panasonic)

Supply, Installation, Testing & Commissioning of IP Network TDN Low-Light IR Dome Each Cameras, 1/2.8" CMOS,4 MP 2592 x1520 or better , triple stream, Min. Illumination required 0.005 Lux/F2.0 (Color,30IRE), 0 Lux/F2.0 (IR ON), 140dB True WDR, triple stream,3 to 12 mm, F1.4 to 2.8 , MFZ, Backlight Compensation, Highlight Compensation 3DNR, Privacy Mask, Internal/External Smart IR LEDs with up to 50m IR distance, H.265& |MJPEG, Inbuilt Video Analytics: Smart Motion Detection, Intrusion Detection, People Counting, Multiloitering, Face Detection, Line Crossing, Missing Object detection, [Unattended Object Detection. THe camera shall have inbuilt cyber security FIPS Chipset.Audio Stream Full Duplex, 1TB SD card support, IP 67 & IK10, Alarm: 1 In & 1out, PoE, H.265 High Profile and MJPEG, PoE Class . Certifications: ONVIF Profile S,G,T & M compliant, NDAA 889 UL, CE, EN, FCC & RoHS compliant and with all accessories and as per detailed tender specifications.

Supply, Installation, Testing and Commissioning of 55" smart LED TV with following specifications a) Full HD 1920 x1080 (4K monitor) b) IPS panel c) Slim back light LED module d) 900 PMI e) Triple XD engine f) Dynamic scanning g) ANR h) True colour generator i) 8modes of picture j) picture wizardIII k) Real cinema 24P l) HDMI -3nos m) USB -3nos n) Built in LAN o) Magic remote p) Dimension 1242 x 724 x 55.1min(37). (Make: Sony/ LG /Samsung). (Rate as per quotation enclosed)

Supply and Clamping of CAT 6 armoured cable in suitable PVC Pipe 1" thick on wall / ceiling with connected PVC accessories with clamps, saddles etc., complete. (Between ethernet switch to camera and radio modem) i. Application : Primary (Campus), Secondary (Riser), Tertiary(Horizontal) IEEE 802.3 : 10Base-T; 100Base-T; 1000Base-T IEEE 802.5 16 MB; ISDN; TPDDI; ATM ii. Standards: ISO/IEC 11801 2nd ed.; IEC 61156-5 2nd EN 50173-1; EN 50288-6-1,EIA/TIA 568C.2, RoHS Compliant. Fire Rating: PVC : IEC 60332-1. iii. Conductor - Bare Copper Wire iv. Insulation - Polyethylene v. Twisting - 2 Cores to the pair vi. Cable lay up - 4 Core to the pair It has diameter of (23 AWG) 0.550 ± 0.015.Insulation : Polyethylene.GI wire of size is 0.90 ± 0.030mm.

Fixing and Termination of CAT 6 Cable RJ 45Jack Single Point ( Point to Point ) Crimping, Testing and arrangement charges.

Supply and fixing of POE 24 port switch 10/ 100 / 1000 Base -T / 2 x 1000Base-FX / 20Gbps bandwidth / IEEE803.af/at compliant PoE+ / RJ45 supports auto MDI/MDI-X function / Auto negotiation speed, half/full-duplex / Store and forward / Max packet size: 10kbytes / Wide range power design (12~56VDC) / Operating temperature (-40 ̊C ~ +75 ̊C) / Reverse polarity protection / Resettable fuse to protect against overcurrent / IP-40 protection / EFT protection for power line.

Supply and Fixing of Rack with Accessories -Higher end 36 U Rack with LNS unit and fan extra for the above rack.

Supply and Installation for 2KVA UPS with Battery, Single Phase UPS (Single Phase In & Single Phase Out) Capacity - System with Battery - 2Hours back up

Supply & Fixing 50W Led Light Model: K-Lite KL-7030 Angle Dixon, Dimension : 865 x 785 x 3660mm, Wattage : 50W LED. NOTE: (i) LED: 2700K,3000K,4000K,5700K (ii) Product Finish: Jet Black

Supply & Fixing of 24w LED Light Model: K-Lite KL-7036 Column Light, Dimension : Ø166 x 2700mm, Wattage : 24W LED. NOTE: (i) LED: 2700K,3000K,4000K,5700K (ii) Product Finish: Graphite Grey, Anthracite grey, Jet Black

Supply & Fixing 6W Led Light Model: K-Lite KL-2747 Wall-Recess, COD (mm) : 124 x 83 x 70, Wattage : 6W LED. NOTE: (i) LED: 2700K,3000K,4000K,5700K (ii) Product Finish: Jet Black

Supply & Fixing 6W Led Model K-Lite KL-4267, Luminaire dimension : 113mm length x 100mm width x 451mm height, Beam angle 15° / 25° / 40°, Wattage : 60W LED. NOTE: (i) LED: 3000K, 4000K, (ii) Product Finish: Jet Black

Supply and Fixing 100W Led Light Model K-Lite KL-1038 , Dimension : 100x200x50, Pole height: 9m, Pole size: Sq100, Arms:4 Wattage : 100W LED. NOTE: (i) LED: 2700K,3000K,4000K,5700K (ii) Product Finish: Jet Black

Supply & Fixing 20W RGB Led Light Model: K-Lite KL-3561 Translucent polyurethane encapsulation., Dimension : 1005 x 25 x 32 , Wattage : 20W LED. NOTE: (i) LED: 2700K,3000K,4000K,5700K (ii) Product Finish: Graphite Grey, Anthracite grey, Jet Black

Supply & Fixing 40W RGB Led Light Model: K-Lite KL-3561 Translucent polyurethane encapsulation., Dimension : 1005 x 25 x 32 , Wattage : 20W LED. NOTE: (i) LED: 2700K,3000K,4000K,5700K (ii) Product Finish: Graphite Grey, Anthracite grey, Jet Black

Supply & Fixing 20W Led Light Model: K-Lite: Leva-4, KL-4319, Lluminium alloy (grade 6063), 3000K,RGBW BA:2°,20°,10°x30°, Clear Toughened GlassFinish: Pure polyester powder coated grey

Supply & Fixing 30W Led Light Model: K-Lite: Navi, KL-4287, Dimension :329 x Ø166 x 160mm , Wattage : 30W LED. NOTE: (i) LED: 2700K,3000K,4000K,5700K BA:45°,28°,10°, Polycarbonate Optical Lens (ii) Product Finish: Graphite Grey, Anthracite grey, Jet Black

PA SYSTEMS

Supply,installation, testing and commissioning of 30W High efficiency ABS horn loudspeaker with weather protectin IP 65 Max Power : 45 W, Rated power, 30 Watts, Power tapping, 30/15/7.5W-Effective frequency range (-10 db) (-380 Hz to 5 kHz) - SPL at rated power (1 khz) 126 dB- Self extinguishing acc. to UL 94 VO - IP 65 acc. to IEC 60529, safety acc. to EN 60065. (Make - BOSCH)

Supply, installaion, testing and commissioning of 240W mixer amplifier with following features : inbuilt bluetooth for audio streaming, sports audio playback from USB pen drive, 4 microphone/line inputs, plus music source input, insert features to use as a pre/power amplifier, Optional 2 tone chime generation for input 1 technical specifications - Frequency response 80 Hz to 18 kHx (+1/-3 dB W - 10 dB ref. rated output) - Distortion <1% @ rated output power, 1 kHz bass control Max +/- 8 dB Treble control max +/- 8 dB. (Make - BOSCH)

Supply, installation, testing and commissioning of 480W Power amplifier in a 3U high housing with 70V / 100V and 8 Ohm outputs, Dual inputs with priority switching, 100V input for slave operating on 100V speaker line, Mains, battery backup, with following features -Output ower (rms) 480W, - Frequency response 60 Hz to 18 kHz (+1 / -3 dB at -10 dB ref rated output) - Distortion <1% @ rated output power, 1 kHz, - S/N (flat at max volume) > 90 dB - Batter power supply 24 VDC (Make BOSCH)

Supply and installation of Handheld microphone with a dynamic transducer element that shall be designed for high speech intelligivility. It should have a rugged enclosure is both stylish and easy to use in a wide range of public and sound reinforcement applications. Polar Pattern unidirectional, frequency range 80 hZ to 12 kHz, Sensitivity 1.7mV/Pa +/- dB, Rate out impedance 600 Ohms. (Make BOSCH)

Supply and laying of FRLS PVC insulated 2 core 1.5 sq.mm. Armoured Copper Cable on ceiling / wall using fixing accessories like screws, plug, clamps, etc., asper standard methods and as directed by the Departmental Officers.

Plumbing

Sanitary Fixtures & Cp Fittings

Supplying and fxing in position White / Colour Special Delux Model Glazed Cascade Type Parryware / Hindware / Equivalent Wall Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fxing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fttings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fttings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifcations. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) with 10 litres capacity flushing tank with all internal dual flush fttings with normal seat cover Wall Fitting

Providing and fixing C.P jet spray / health faucet with required length of flexible tube, clamp and bracket for fixing to wall as per required. Hand shower (Health Faucet),flexble tube&wall Bracket(Model No-ALD -565)

Providing and fixing C.P Brass angle valve 15 mm complate as per required. (Make: CP Angle stop cock with wall flange (Model no-FUS-29053)

Providing and fixing 450mm Long Braided Hose pipe with M10X1 Nipple, 15mm Nut, O-Ring & Rubber Washer (Suitable for Wash Basin, Kitchen Sink etc.) of approved make and conforming to Manufacturers Standards.

Supplying and fixing white Wash Hand Basin of size 550mm x 400mm with all accessories such as Cast Iron Brackets, 32mm dia CP Waste Coupling, Rubber Plug and Chain, 32mm dia ‘B’ Class GI Waste Pipe, 15mm dia GM Wheel Valve, 15mm dia Nylon Connection,15mm dia Brass Nipples, 15mm CP Pillar Tap etc Colour with Pedastal

Providing and fixing pillar tap, capstan head, screw down high pressure with screws, shanks and back nuts. .

Providing and fixing chromium plated, bottle trap with necessary couplings of approved quality for wash basin.

Providing and fixing in position superior quality and approved make Lipped Mouth Porcelain Flat Back Urinal with all accessories such as 32mm dia Bell Mouth PVC Connection, 15mm dia GM Wheel Value, 15mm dia ‘B’ Class GI Waste Water Pipe, 15mm dia Nylon Connection, 15mm dia Brass Nipple etc..

Supplying and fixing 60x45cm best Belgium mirror (bevelled edge)with plywood back,etc.,complete.

Supplying and fixing chromium plated brass towel rail 60cm long with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Supplying and fixing chromium Porcelain Soap Dish of size 150mm x 150mm x 50mm of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).

Providing and fixing in position 15mm dia CP brass Bib Cock with cover flange plate including CP brass extension nipple wherever required and all necessary fittings etc complete.

Supply, storing, installation and testing liquid soap dispenser with CP / SS cap and bracket, fixed to wall with CP brass screw, etc. complete. (Make: Hind ware/cera/jaguar/Grohe)

Providing and fixing of grab bars 300 mm Stainless steel in physically disabled toilet including all necessary fitting, SS Screws & Accessories etc.Complted in all manners and satisfied to of EIC.(Make: Hind ware/cera/jaguar/Grohe)

Providing and fixing of grab bars Vertical Swing 18-8 S, type-304, 18-gauge (1mm) stainless steel tubing with satin-finish. 1–1/4 (25mm) outside diameter wall mounted in physically disabled toilet including all necessary fitting, SS Screws & Accessories etc.Complted in all manners and satisfied to of EIC.(Make: Hind ware/cera/jaguar/Grohe)

Water Supply Piping

Pipes and pipe accessories, traps, supply of supports and support fixing, chase cutting and making good the surfaces, coving, core cutting, etc. shall be in the Scope of the Contractor. All consumables other than materials supplied by manufacturer required for fixing the china ware, sanitary ware and CP fittings and fixtures shall be provided by the Contractor. All the shaft clamps (inclusive in unit rate) shall be with slotted FRP channel, 6mm MS L bend, U bolts with silicon rubber with required nuts and washer set. The clams shall be considered at min 1 distance in shaft. For suspended plumbing the clamps shall include 10mm anchor fastener with 10mm threaded rod of required length with 25 x 2mm oval clamps with silicon rubber @ min 1Mt distance.

Internal Water Supply Supplying, laying and jointing CPVC pipes (having working pressure 10kg/SqCm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using CPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works.

15mm dia

20mm dia

25mm dia

32mm dia

40mm dia

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

20mm dia Wheel Valve

25mm dia Wheel Valve

32mm dia Wheel Valve

40mm dia Wheel Valve

50mm dia Gate Valve

External Water Supply Arrangements Providing laying and jointing in true line UPVC Pipe (SCH- 80) for cold water including fittings make Ashirvad / Prince / Supreme / Astral / Finolex or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every 2meter C/C or shall be concealed as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

20mm dia

25mm dia

32mm dia

40mm dia

50mm dia

Providing and fixing in position of approved quality G.M. float valve with copper ball float and brass rods of required length suitable for test pressure of 5Kg/SqCm of the following sizes : [A] 50mm.

Providing and fixing 20mm diameter Brass Air release valve, double acting, screw end of approved make complete as per engineer in charge.

Making connection with the external water supply main, OHT connection including providing of required length of pipes (for connection), fittings & necessary fixtures.

Providing, Fixing, testing and commissioning of C.I. Non Return dual plate Valve of specified diameter as per technical specifications and directions of the Project Manager. The rate shall include providing gaskets 6mm thick and reducers.

40mm dia.

50mm dia.

Providing and fixing cast iron 'Y' strainer suitable to pipes of following dia. including flange. Min Pressure Rating should be PN16. Body should be ductile Iron With Epoxy Coating & Gasket of EPDM material. Filter Screen : Stainless Steel, Medium Temperature -10-120°C, End Connections : Flanged

50mm dia.

Supplying and erecting SINTEX or approved equivalent make HDPE plastic vertical cylindrical 2000 Litre Water Storage Tank. Strickly adhering ISI Standard as per ISI Mark 12701 (Latest revision) including all taxes and freight charges within Corpn.City limit.

Constructing brick masonry chamber for underground Valve chamber and bends with bricks having crushing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm internal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete.(ii) Inside dimensions 600mm x 600 mm and 600mm deep for pipe line with one or two inlets. (more than 10 ton)

Drainage System (Soil,Waste & Rain Water Piping)

Pipes and pipe accessories, traps, supply of supports and support fixing, chase cutting and making good the surfaces, coving, core cutting, etc. shall be in the Scope of the Contractor. All consumables other than materials supplied by manufacturer required for fixing the china ware, sanitary ware and CP fittings and fixtures shall be provided by the Contractor. All the shaft clamps (inclusive in unit rate) shall be with slotted FRP channel, 6mm MS L bend, U bolts with silicon rubber with required nuts and washer set. The clams shall be considered at min 1 distance in shaft. For suspended plumbing the clamps shall include 10mm anchor fastener with 10mm threaded rod of required length with 25 x 2mm oval clamps with silicon rubber @ min 1Mt distance.

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 6 kg/SqCm including cost of necessary PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

110mm dia PVC Pipe

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6kg/SqCm pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level.

110mm dia.

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

110mm dia PVC Plain Elbow

110mm dia PVC Door Elbow

110mm dia PVC Plain Tee

110mm dia PVC Door Tee

PVC Y with door 110mm dia

Providing and Fixing RIGID PVC Pipe for Kitchen Sink, basin wash out & urinal wash out pipe ISI marked brand as per IS:4985 (6KG) complete with PVC Fittings & claps & hinges including cutting and making good the walls & ceiling for waste pipes, connections & as directed by the engineer-in-charge. (Astral / Ashirvad / Supreme)

40mm dia INCLUDING ALL BENDS

Supplying and fixing in position PVC cowls of following dia of best approved quality conforming to BIS, etc., complete complying with standard specifications. (The PVC cowl should be got approved by the Executive Engineer before use on works).

110mm dia.

CI Nahani Trap / Floor Trap Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of crushed stone sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works). Nahani Trap of size 100 x 75mm with stainless steel gratings.

External Drainage Sysytem(Soil, Waste & Rain watering pipe)

Providing, Fixing, testing and commissioning of under ground UPVC foam core multi layer pipes SN-8 having outer and inner layers of conventional PVC and middle layer of foamed PVC with fittings of specified diameter with all necessary excavation, providing and laying PCC (1:4:8), laying, refilling, compaction, dewatering, curing, retesting and disposal of any excess earth / soil from the site as per & complete to specifications, drawings, details as directed by Project Manager. (The pipe should be laid with sand layer 150mm above and below the pipe with encasing as per directed by the Project Manager).

160mm dia

200mm dia

Construction of Inspection chamber of size 60x60x60cm with necessary earth work excavation, 40mm size brick jelly concretein C.M.1:4:10 ( 1 cement, 4 Crushed Stone Sand (Commercially called M-Sand) and 10 broken brick jelly)stock brick work in c.M.1:y (1 cement and 6 Crushed Stone Sand (Commercially called M-Sand)) for 23cmthick wall, benching, channelling and plastering,interior,exterior and top with c.M.1:3 (1 cement and 3 Crushed Stone Sand (Commercially called M-Sand) Sandsand) 12mm thick and providing 7.5cm thick RCC loose slabcovering in CC 1:2:4 ( 1 Cement,2 Crushed Stone Sand (Commercially called M-Sand) and 4 blue granitebroken stone jelly of 12mm to 20mm size) with necessary reinforcement and arrangements to lift for cleaning purpose,etc.,complete.

Construction of inspection chamber of size 60x60x90cm with necessary earth work excavation, 40mm size brick jelly concretein C.M. 1:4:10 ( 1 cement, 4 Crushed Stone Sand (Commercially called M-Sand) and 10 broken brick jelly) stock brick work in C.M. 1:6 (1 cement and 6 Crushed Stone Sand (Commercially called M-Sand)) for 23cm thick wall, benching, channelling and plastering,interior, exterior, and plastering, interior, extrior and top with C.M. 1:3 ( 1 cement and 3 Crushed Stone Sand (Commercially called M-Sand)), 12mm thick and providing 7.5cm thick R.C.C loose slab covering in C.C. 1:1.5:3 (1 cement, 1.5 Crushed Stone Sand (Commercially called M-Sand) and 3 blue granite broken stone jelly of12mm to 20mm size) with necessary reinforecement and arrangementsto lift for cleaning purpose, etc., complete.

Construction of inspection chamber of size 60x60x120cm withnecessary earth work excavation, 40mm size brick jelly concretein C.M.1:4:10 (1 cement,4 Crushed Stone Sand (Commercially called M-Sand) and 10 broken brick jelly)stock brick work in C.M.1:6 ( 1cement and 6 Crushed Stone Sand (Commercially called M-Sand)) for 23cmthick wall, benching, channelling and plastering, interior,exterior, and top with C.M.1:3 (1 cement and 3 Crushed Stone Sand (Commercially called M-Sand)), 12mm thick and providing 7.5cm thick RCC loose slab covering in C.C.1:1.5:3 ( 1 cement ,1.5 Crushed Stone Sand (Commercially called M-Sand) and 3 blue granite broken stonejelly of 12mm to 20mm size) with necessary reinforcement andarrangements to lift for cleaning purpose etc.,complete.

Supplying and fixing 15x10cm stoneware gully with 'P'or 'S' trapwith 15x15cm C.I.grating and 10cm dia S.W.bend including 40mm size brick jelly concrete in C.M.1:4:10 ( 1 cement, 4 Crushed Stone Sand (Commercially called M-Sand) and 10 broken brick jelly 40mm gauge),10cm thick alround the gully, 11cm thick wall with stock brick work in C.M.1:4 ( 1cement and 4 Crushed Stone Sand (Commercially called M-Sand)) upto ground level and plastering with C.M.1:3 (1 cement and 3 Crushed Stone Sand (Commercially called M-Sand),12mm thick for gully silt pit of size 15x15cm etc.,complete.

Making connection from central existing sewer pipe line, STP and Septic tank and soak well by breaking, excavation dewatering, purchasing / fabricating suitable size fittings for connection, refilling etc. comp. work to be done as per the local authority requirement including all liasoning cost.

Supplying and fixing FRC cover and frame 60x60cm size including necessary masonry work with cement mortar, fixing inposition,etc.,complete.

Supply and fixing, water level controller for the Under ground tanks of approved make complete, as directed.

Plant and Machineries

Supply, installation, testing and commissioning of Hydro pneumatic Horizontal Multistage Pump's system, PRESSURISED WATER FROM UGWT TO OHT - Each Pump Flow : 10m3/hr, Each Pump Head : 50Mt, Pump MOC : Pump Head & Base - CED Coated CI, Assembly - SS304, SUC & DEL - 40 x 40mm Each Pump Motor : 1.1KW (1.5HP), 2Pole, 3Phase, 50Hz, IE3. Control Panel (1W+1S) : Control Panel IP54 Equivalent, Multi VFD based inbuilt PLC & Cascade operation. Pressure Tank - 100Litre pressure tank (Global make, 10 Bar). Scope of Supply : Pump set (2 Nos.) Skid Mounted, Control Panel (Wall Mounted 1 No), Suction & Discharge Header with Isolation & NRV, Pressure Gauge & Pressure transmitter, Pressure tank, Air Vent Valve.

Supplying and erecting in position of following liters capacity Industrial Model Reverse Osmosis Water-cumPurifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact. 50 Litres

Filteration System & Cleaning Accessories

Supply of Bobbin Wound FRP Filters Top Mounted Connection, the inner distribution system and under bed draw off system shall be of hub and lateral type. The filter shall be equipped with man hole, air drain, water / sand draining hole inlet/outlet with union and minimum working pressure of 2.5 kg/cm2 with MPV, valves, pipe supports and media complete in accordance to the manufacturers specification. Max. Permissible Velocity 35 m3/m2/hr. Dia: 450mm, Flow Rate: 5 m3/hr for the filter Size of Multiport Valve - 1.5"

Supply of Self-Priming Centrifugal Monobloc Pump Horizontal, closed coupled, single stage Centrifugal Self-Priming Pump with, 6m3/hr@10m, with mechanical shaft seal and one piece pump motor shaft. Rated Speed: 2900. 0.5 HP Enclosure class: IP 55, Insulation class: Class F Single Phase: 220 - 240 V (1-working)

Supply of Pump Starter and Necessary Piping and Wiring for Cleaning Trolley

Supply of SS Suction Sweeper/vaccumme Head, fixed with clip type connection of 1-1/2". Size: 450mm

Supply of Floating Suction / Hose Pipe, made of polyethlyne in blue colour, connection : 40mm, 15m Long

Supply of Water Deep Skimmer.

Supply of Water Surface Skimmer.

Supply of Reinforced Telescopic Handle, Pool Cleaning. Size: 4.8mtr

Supply of Straight brush.

Supply of Algae Brush with SS Bristle, 40mm Clip type connection

Supply of Test Kit for measuring Chlorine & pH Levels in pool water

Supply of TCCA90 Chemical

Supply of HCL

Supply, Installtion, Testing & Commissioning of Horizontal Openwell submersible Pump having capacity of 210000 LPH. MOC : Cast Iron,Three Phase 2880 rpm motor - 415 V,50hz. (2-Working for Clear Sheet)

Supply, Installation, Testing and Commissioning Drain Grill, Rectangular of 300mm x 300mm, Made of ABS White plastic

Supply, Installation, Testing and Commissioning of Nozzle Mount LED Lighting of RGB, made of ABS white plastic, 18 W, 12 volts, with 1 meter inbuilt electrical cable

Supply, Installation, Testing and Commissioning of Transformer for the all Under Water LED Light,wich convert 12 v power.

SITC of PVC, PN6, piping including all fittings such as bands, elbows, reducer,tees, union, coupler, tail piece, flanges etc. cost shall be providing supports as per specification and making goods. Pipes shall be connected to pumps, equipments, etc to tail piece for swimming pool plant room piping only.

SITC of Electrical Cables for underwater LED lights and for all pumps other electrical equipments. 2.5 sq.mm 4 core

Supply, Installation, Testing and Commissioning of Starter Panel for Pump

Labour & Supervision Charges for Installation, Commissioning of Entire Waterbody System as per BOQ. Included with Stabilizing Basin and Operator Training

Multiple Transportation During Erection and Installation Work

Signanges

Parking Signage: Providing And Fixing of Retro Refelctorised Cautionary, Mandatory And Informatory Signs (Without Definition Board) Made Out of High Intensity Prismatic Grade Sheeting Conforming To Type – Iv Standards of Irc 67 : 2012 And Astm D 4956 – 09, Specification And Fixed Over 2mm Thick Aluminium Sheet Fixed Over a Back Supporting Frame of 25mm X 25mmx3mm. Mild Steel Angel And Supported On A Mild Steel Angel Post 75X75X6mm With A Clear Height of Not Less Than 2.10M From The Ground Level To The Bottom of The Sign Board And 0.60M Below Ground Level. The Sign Post Should Be Painted As Per Irc 67-2012 And Firmly Fixed to The Ground By Means of Properly Designed Foundation With M15 Grade Cement Concrete 45cmx45cmx60cm Size Including Cost And Conveyance of All Materials, Equipment, Machinery And Labour With All Leads And Lifts, Loading Charges Necessary For Satisfactory Completion of The Work As Directed By The Engineer In Charge. High Intensity Retro – Reflection Sheet Shall Consist of Minimum Coefficient of Retro- Reflection As Per Table 6.6 of Irc 67- 2012. The Retro Reflection Sheeting Shall Be Covered Under 7 Years Warranty Issued For Field Performance And A Certified Copy of Three Years Outdoor Exposure Report Shall Be Obtained As Per Irc 67:2012 (As Per Mort&H Specification No.801)

Way Finding Pylon Signage: Spec: 150mm depth painted aluminium can with stencil cut letters. 3mm thick white acrylic fixed on back of the aluminium. 50x50mm SHS SS pipe structure with 1.2mm SS brush finish Sheet cover on fascia. Signage to be fixed with the help of 850x250x8mm thick SS base plate with necessary fixtures

Providng & fixing signage using Stone with letter etching as given in the drawing and as per requirements

Miscellaneous

Jungle Clearance

Kinetic Sculptures

Providing and Fixing tiltable SS Dustbin as per requirement and complete

Providing & Fixing Play Area Swing as per requirement

Providing & Fixing Monkey Climber as per requirement

Providing & Fixing Bridge Ladder Scrambler as per requirement

Providing & fixing Suspended Beams as per requirement

V NARAYANAN (BID ID -1116410)

Sri Sivaram and co (BID ID -1116404)