SPL REP TO LS BN PH PUMP HOUSE LT PANEL CABLE SPL REP NEW WIRING WITH PVC CASING CAPING OF OFFR BLDG NO P500 P487 P488 P489 OF WEU PO CHEM EARTH AT OPTO SET OF CORP ZONAL WKSP CERAIN MINOR WORKS UNDER GE 865 EWS AT LEH

Amount

Taking down carefully copper/Aluminum point wiring (Light, Fan, Socket or power) complete fitting such as switches, ceiling, regulator, sockets etc removing materials to be store for keeping in safe custody for taking credit and making good disturbed surfaces of walls, floors etc as directed.

M&L for point wiring for one light point or fan point controlled by one switch with PVC insulated copper conductor stranded cable of size 1.5 sqmm and including PVC casing/caping terminated in existing sunk CI/pressed steel terminal boxes for fixing and 1.5 sqmm PVC insulated copper wire as earth wire connected to earth wire connected to earth folly and 3.0mm thick plastic laminated sheet cover all as specified and directed by Engr-in-Charge. Make of cable: L&T/FINOLEX/GRANDPLAY/ANCHOR/ POLYCAB Make of casing caping PLAZA/FINOLEX/ SUPREME/PRESTO PLAST

All as per item No 2.00 here-in-before but 1.5 Sqmm for one 3 pin 5 amps socket outlet including 1.5 sqmm insulated copper wire as earth wire to the same earth dolly on the same board complete all as specified and directed by Engr-in-Charge. Make of cable: L&T/FINOLEX/GRANDPLAY/ANCHOR/ POLYCAB Make of casing caping PLAZA/FINOLEX/ SUPREME/PRESTO PLAST

All as per ser Item No 2.00 here-in-before but, for point wiring for 3 pin 5 amps socket outlet independent with copper conductor cable PVC insulated multistrand 1.5 sqmm 1.5 sqmm PVC copper conductor as earth wire connected to earth dolly and including PVC casing/caping with sunk cast iron. Make of cable: L&T/FINOLEX/GRANDPLAY/ANCHOR/ POLYCAB Make of casing caping PLAZA/FINOLEX/ SUPREME/PRESTO PLAST

All as per item No 2.00 above but for power point 3 pin switch socket 15 Amp with PVC copper conductor cable multistrand unsheathed 4.00 Sqmm on independent board incl one run 2.5 Sqmm multistrand PVC copper conductor cable for earth continuity in and including PVC casing and capping fixed on wall incl teak wooden board with 3mm thick of hylam top sheet complete all as specified and as directed. Make of cable: L&T/FINOLEX/GRANDPLAY/ANCHOR/ POLYCAB Make of casing caping PLAZA/FINOLEX/ SUPREME/PRESTO PLAST

S&F for socket outlet 5Pin, 5A, flush type 230 Volts complete all as specified and directed. Make : Anchor/Legrand/Crabtree/Cona

S&F for socket outlet 6Pin, 5A and 15 Amps flush type 230 Volts complete all as specified and directed. Make : Anchor/Legrand/Crabtree/Cona

S&F lamp holder PVC/Polycorbonate type insulated body with back plate suitable for batten fittings as specified and directed. Make : Anchor/Legrand/Crabtree/Cona

S&F in replacement of LED Bulb 10 Watts, 230 volts, 50 hz, AC, complete all as specified and as directed. Make : Cat part No - LHLDEUHEMK8P010 of Havells or equivalent in Bajaj/Philips.

S&F switch piano flush type one way single pole 5 Amp 240 volts. Make : Anchor/Legrand/Crabtree/Cona

M&L for ceiling rose 3 phase, PVC/polycarbonate isolated body all as specified and directed by Engr-in-charge. Make : Anchor/Legrand/Crabtree/Cona

S&F in replacement of STRATO 2x2 Sesthetically designed 2x2 LED flat panel which provides soft-light and glare free symmetrical illumination also for POP ceilings 36 Watt slim type with LEDDRIVER36V36WS complete all as specified and directed by Engr-in-Charge. Make : Cat Part No STRATO2x2PLR36WLED857MOD of Havells or equivalent in Bajaj/Philips.

S&F in replacement of LED single tube light fitting surface / pendent mounting complete with batten for LED tube light 20 Watt with , extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver complete all as specified and directed by Engr-in-Charge. Make : Cat Part No STOUTPLUS600BS20WLED857SPCWH, HSN Code 9405 of Havells or equivalent in Crompton/Bajaj

Supply & Fixing in replacement of surface mounted Bulk Head fitting Environmental friendly, ultra modern, energy saving, surface mounted, decorative oval bulk head edge-lit LED luminaire comprising of high brightness LEDs 10 Watt complete all as specified and directed by Engr-in-Charge. Make : Cat Part No HEXAFT10WLED857SSYMBOPC of Havells or equivalent in Crompton/Bajaj

Supply and fixing MCB distribution board Double door, regal grey, sheet metal enclosure, SPN 240 volts 12 way with 200 amps rated bus bar concealed to wall and making flush with wall surfaces and making good to disturbed surfaces of walls to match with the exisiting surface etc incl taking down old DBs. Make: Cat part No 5076 12 of Legrand (Ekinoxe) or equal approved in Schneider (Acti-9)/Siemens (Betagard-8GB32)

Supply and fixing MCB distribution board Double door, regal grey, sheet metal enclosure, SPN 240 volts 8 way with 200 amps rated bus bar concealed to wall and making flush with wall surfaces and making good to disturbed surfaces of walls to match with the exisiting surface etc incl taking down old DBs. Make: Cat part No 5076 11 of Legrand (Ekinoxe) or equal approved in Schneider (Acti-9)/Siemens (Betagard-8GB32)

Supply and fixing MCB SPN 40 Amps, 'C' series, 230 V A/C complete incl taking down old MCBs all as specified and as directed by Engineer-in-Charge. Make: Cat part No 4086 18 of Legrand (DX³) or equal approved in Schneider (Acti -9)/ Siemens (Betagard-5SL4)

Supply and fixing MCB SP 6 to 32 Amps, 'C' series, 230 V A/C complete incl taking down old MCBs all as specified and as directed by Engineer-in-Charge. Make: Cat part No 4085 87 to 4085 95 of Legrand (DX³) or equal approved in Schneider (Acti -9)/ Siemens (Betagard-5SL4)

Supplying, laying, jointing and testing underground cable PVC XLPE insulated armoured and PVC sheathed LT 1100 volts grade (heavy duty) with aluminium conductor 2 core, 10 Sqmm, confirming to IS-1554, laid in ducts/through pipes, in floor, on poles, in trenches including taking down of old cable complete all as specified and directed by Engr-in-Charge. Make : Cable Corporation of India/Finolex Cable Co/Polycab/ Gloster/Havells/KEI/ RR Kabel Note :- Clamps, GI pipes, excavation, earth work, sand cushioning and brick protection cover shall be measured and paid for separately.

Excavating in trenches, n exc 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, for laying cables/pipes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth in hard/dense soil and getting out soil, complete all as specified and as directed by Engineer-in-Charge.

Returning filling in (soil) including spreading, levelling, watering and well ramming in layers n.exc 25cm thick in any type of soil complete all as specifed and as directed by Engineer-in-Charge.

Removal of excavated material (soil) to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specifed and as directed by Engineer-in-Charge.

M&L for Sand cushioning to underground cables 8 cm below the cable before laying & 15 cm above the cable after laying, including punning upto total 18 cm thick complete all as specified in clause 19.75 of SSR Par-I, complete all as specified. Note : Only punned thickness of 18 cm will be measured and paid.

Supply and laying factory made, machine pressed, unreinforced, pre-cast concrete cable cover class LV type-I flate size 250x150x40mm, complete all as specified and directed

Supply and fix in replacement of Off load Change over switch (Side handle) with advance neutral, 415 Volt in sheet metal inclosure 4 Pole of capacity 200 Amps with connecting acessories complete all as specified and directed. Make : Havells cat part No : IHBFFE0200 or equivalent of HPL/C&S/Legrand/ABB/Schneider/Siemens

S&F in replacement Air circulator exhaust fan plastic body of size 300 mm sweep with louvers & shutters and connecting up including provn of cable from ceiling rose to connector of fan controlled by one way switch complete all as specified and directed by Engr-in-Charge. Make : Orient/Usha/Havells/Khaitan/CG

Supply, fixing, connecting and testing street light LED type suitable for working on 230 volts, 50 Hz, AC of 48 Watts with suitable size GI pipe 1.5 mtr and 02 Nos MS clamp with nut and boltscomplete all as specified. Make : Cat Part No. ENDURAPEARLNEOSL48WLED757PASYTOPC of Havells or equal approved in Crompton Greaves/Bajaj.

Sub main wiring with two runs of 6 Sqmm (2x6 sqmm) 1100 volts grade single core FRLS PVC insulated unsheathed multistranded copper conductor confirming to IS-694 drawn through and including non-metalic PVC conduit of suitable dia, ISI marked with all accessories etc with one run of 6 Sqmm (1x6 sqmm) single core FRLS PVC insulated unsheathed copper conductor cable as earth wire and making good to match with existing surfaces including taking down of old sub main wirings complete all as specified and directed by Engineer-in-Charge. Note:- 2 runs of 6 Sqmm (2x6 sqmm), one run of 6 Sqmm (1x6 sqmm) cable and one metre of PVC Conduit will be measured as one unit. Make of cable: L&T/FINOLEX/GRANDPLAY/ANCHOR/ POLYCAB Make of Conduit : PLAZA/FINOLEX/ SUPREME/PRESTO PLAST

Material and labour for earthing complete with galvanised steel earth plate 600 x 600 x 6 mm buried directly in ground vertically to a depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below ground level connected to and including GI wire of size 4 mm dia by means of nuts, bolts, washers etc made of and connected to test point and earth dolly as all shown in electrical plate No.3 of SSR Part-I 2009 and specified or indicated including excavation and earth work in any type of soil PCC (1:3:6) type C1 in chamber, pre cast RCC slab 50mm thick in cement concrete (1:2:4) type B1, reinforced with welded steel wire fabric or XPM jali (weight not less than 4.0 kg/Sqm) with cast iron frame, funnel, with wire mesh, 20mm bore medium grade GI watering pipe, lugs, 15mm bore light grade GI protection pipe, test point etc including taking down of old u/s earthing set complete all as specified and as directed. Note: (i) Item includes the cost of 7.5 m GI pipe for protection of earth lead. Any additional length shall be adjusted through deviation order. (ii) Item includes the cost of 7.5 m GI earth lead. Any additional in length shall be adjusted through deviation order (iii) Item includes the cost of Charcoal and commercial salt

S&L galvanized iron tubing 'light grade' 100 mm bore, with all fittings, laid in trenches or under road crossing as protection pipe, or fixed alongwith walls/poles with clamps including bolts, nuts & washers, including taking down old steel tubing and connections complete all as specified and directed. Make : Jindal/TATA/BST/Prakash Surya

S&L galvanized iron tubing 'light grade' 50 mm bore, with all fittings, laid in trenches or under road crossing as protection pipe, or fixed alongwith walls/poles with clamps including bolts, nuts & washers, including taking down old steel tubing and connections complete all as specified and directed. Make : Jindal/TATA/BST/Prakash Surya

Supplying, laying, jointing and testing underground cable PVC XLPE insulated armoured and PVC sheathed LT 1100 volts grade (heavy duty) with aluminium conductor 3.5 core, 400 Sqmm, confirming to IS-1554, laid in ducts/through pipes, in floor, on poles, in trenches including taking down of old cable complete all as specified and directed by Engr in Charge. Make : Cable Corporation of India/Finolex Cable Co/Polycab/ Gloster/Havells/KEI/ RR Kabel Note :- Clamps, GI pipes, excavation, earth work, sand cushioning and brick protection cover shall be measured and paid for separately.

Supplying, laying, jointing and testing underground cable PVC XLPE insulated armoured and PVC sheathed LT 1100 volts grade (heavy duty) with aluminium conductor 3.5 core, 240 Sqmm, confirming to IS-1554, laid in ducts/through pipes, in floor, on poles, in trenches including taking down of old cable complete all as specified and directed by Engr in Charge. Make : Cable Corporation of India/Finolex Cable Co/Polycab/ Gloster/Havells/KEI/ RR Kabel Note :- Clamps, GI pipes, excavation, earth work, sand cushioning and brick protection cover shall be measured and paid for separately.

Supplying, laying, jointing and testing underground cable PVC XLPE insulated armoured and PVC sheathed LT 1100 volts grade (heavy duty) with aluminium conductor 3.5 core, 120 Sqmm, confirming to IS-1554, laid in ducts/through pipes, in floor, on poles, in trenches including taking down of old cable complete all as specified and directed by Engr in Charge. Make : Cable Corporation of India/Finolex Cable Co/Polycab/ Gloster/Havells/KEI/ RR Kabel Note :- Clamps, GI pipes, excavation, earth work, sand cushioning and brick protection cover shall be measured and paid for separately.

Supplying, laying, jointing and testing underground cable PVC XLPE insulated armoured and PVC sheathed LT 1100 volts grade (heavy duty) with aluminium conductor 4 core, 25 Sqmm, confirming to IS-1554, laid in ducts/through pipes, in floor, on poles, in trenches including taking down of old cable complete all as specified and directed by Engr in Charge. Make : Cable Corporation of India/Finolex Cable Co/Polycab/ Gloster/Havells/KEI/ RR Kabel Note :- Clamps, GI pipes, excavation, earth work, sand cushioning and brick protection cover shall be measured and paid for separately.

Material and labour for earthing complete with galvanised steel earth plate 600 x 600 x 6 mm buried directly in ground vertically to a depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below ground level connected to and including GI strip of size 25x4mm as earthing leads by means of nuts, bolts, washers etc made of and connected to test point and earth dolly as all shown in electrical plate No.3 of SSR Part-I 2009 and specified or indicated including excavation and earth work in any type of soil PCC (1:3:6) type C1 in chamber, pre cast RCC slab 50mm thick in cement concrete (1:2:4) type B1, reinforced with welded steel wire fabric or XPM jali (weight not less than 4.0 kg/Sqm) with cast iron frame, funnel, with wire mesh, 20mm bore medium grade GI watering pipe, lugs, 40mm bore light grade GI protection pipe, test point etc complete including taking down of old u/s earthing set all as specified and as directed. Note: (i) Earth pit chamber and RCC pit cover shall be painted with two coats of red synthetic eanmel paint over one coat of primer including preparing of surfaces. (ii) Item includes the cost of 7.5 m GI pipe for protection of earth lead. Any additional length shall be adjusted through deviation order. (iii) Item includes the cost of 7.5 m GI earth lead. Any additional in length shall be adjusted through deviation order (iv) Item includes the cost of Charcoal and commercial salt

Supply, installation, testing and Commissioning in replacement of Street light Panel cubical type pole/floor mounted totally enclosed made out of 2.16 mm thick CRCA powder coated sheet and angle iron base frame of height 2' accompained with 65 Amp contactor, TPN MCB 63 Amp, max capacityy 12 kW, with digital type timmer switch internally pre wired suitable for 3 phase power supply complete all as directed by the Engr-in-Charge. Make : Cat Part No IHXTS0912A of Havells or equal approved in L&T/Siemens

Supply, installation, testing and commissioning of Oil fired Hot Water Heater up to 85 degree centigrade continuously for industrial process or human requirement, working on kerosene/Diesel as fuel, the body of the boiler is coated with electrostatic powder coating on galvanised sheet metal of sheet 4 mm thick inner and 3 mm outer, fitted with standard burner with nozzle ignition transformer photocell thermostatically controlled with digital temperature meter, provided withrock wool insulted duly covered with aluminium sheet to prevent heat loss of standard capacity 500 ltrs alogwith HDPE Fuel tank for 10 Hrs continuous working duly anchored with the body and connected to burner and provided with suitable size angle iron stand duly painted with red oxide followed by black enameled paint including installation, testing commissioning & one year warranty complete all as specified and directed by Engr-in-Charge. Make : Top Mind Industries Private Limted/EECCO FLAME/FLAMECO/THERMEX

Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required with and including copper strip 20x3 mm with saddles and fixing screws etc. for roof conductors and down conductors above ground complete all as specified and as directed.

Material & labour for Chemical earthing complete with copper plate electrode 900mm x 600mm x 5mm burried directly in ground vetically to a depth not less than 4.70 mtr below normal ground level (with top edge of earth plate not less than 3.60 mtrs below ground level ) connected to copper strip 32 mm x 6 mm as main earthing lead by means of tinned copper/ brass bolts nuts checknuts, and washers besides brazing ( copper strip shall be 0.5 M overlaped with copper plate by brazing) at all joints all as directed and connected to earth test point all as specified and testing on completion with and including necessary excavation and earth work in any type of soil earth,GI pipe medium grade 50 mm bore for protection of copper strip from earth electrode to and including the earth test point of galvanised Iron/steel , adequate quality of charcoal dust, common salt and magnesium sulphate in alternate layers of 100 mm thick x 6 layers all around the plate and RCC cover with size of angle iron 54x54x50 mm, (1:2:4) type B1 using 20 mm graded crushed stone aggregate reinforced with 8 mm dia TMT bars @ 75mm C/C both ways with mild steel handle 12 mm dia, PGI funnel with wire mesh, 20 mm dia GI pipe light grade for watering all as shown in drawing Note - 1. Cost of copper strip and GI protection pipe up to a distance 7.5 M shall be included in quoted rate of above Items. 2. On testing, after completion of job, if desired, earth resistence is not found i.e. below 1.00 Ohms, the earthing shall be redone by the contractor without any extra cost to the department.

Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw complete all as specified and as directed.

Supply and fixing refrigerator (Single door Cooler black), electric driven (single phase), 230 Volts, 50Hz, single door with front glass of capacity 320 ltr complete all as specified and as directed by Engr-in-Charge. Make : Voltas Model No. VC 320 BLK/GFLS or equal approved in Whirlpool/Blue Star/Samsung

M&L for surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard/ dense soil complete all as specified and directed

Excavating over areas, n exc 1.5 m deep and getting out hard/dense soil complete all as specified and directed.

Excavation over area exc 1.50 m deep and n exc 3.00m in depth and getting out in hard/dense soil complete all as specified and directed.

M&L Plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregates as in sub base, foundation, filling and mass concrete, complete all as specified and as directed by Engineer-in-Charge.

Walling of random rubble, uncoursed stone masonary, well bonded, laid dry in retaining wall, abutment and similar work complete all specified and as directed

Walling of random rubble, uncoursed stone masonary, well bonded, bedded and solidly hearted, built in CM 1:6 complete all specified and as directed

Use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc to obtain rough flat finished surface of concrete complete all as specified and as directed.

Formwork to edges of rough finished concrete flat surfaces, treads , breaks in flors, window cills concrete railing s openings in concrete walls , floors and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar works exc 10 cm but n exc 20 cm wide

Reinforced cement concrete 1:2:4 type B1, (using 20 mm graded crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and as directed by Engineer-in-Charge.

M&L pre-cast RCC 1:2:4 type B1 using 20mm graded aggregates for precast cement conc slabs as in drain/ manhole covers, chullah hoods, chajjas, water troughs , mangers , shelves and similar articles and set in CM 1:6

TMT mild steel bars, 10mm dia and over, as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) , complete all as specified and as directed by Engineer-in-charge.

Supply and filling of broken bricks for loose filling of gauge 80mm to 150mm graded complete all as specified and as directed.

Plain cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregates as in sub base, foundation, filling and mass concrete, complete all as specified and as directed by Engineer-in-charge.

Providing, cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregates) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, bed blocks for hold fasts, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, all as specified and directed by Engineer-in-Charge.

TMT mild steel bars, 5mm dia and over upto and including 10mm dia, as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) , complete all as specified and as directed by Engineer-in-charge.

M&L for pre cast cement concrete block masonary of 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) with soild blocks, exc.10cm in width, set and jointed in cement mortor 1:6 complete all as spd and directed.

Material & Labour for rendering 15mm thick in cement mortar 1:4 on fair faces of brick walls or on concrete surfaces plastered surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Material & Labour for rendering 10mm thick in cement mortar 1:6 on other than fair faces of brick walls or stone masonary plastered surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L broken stone and boulders hardcore of gauge n exc 63 mm, deposited, spread and levelled in layers n exc 15 cm thick water and rammed to a true surface complete all as specified and directed.

M&L for plain cement concrete 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) 100 mm thick sub base, sub floor and pavings complete all as specified and directed.

M&L for plain cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) 100 mm thick as in floors and the like including the finishing the surfaces even and fair complete all as specified and directed.

M & L for joint free Non-Skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed or bedding layer in Cement Mortar 1:4 for laying floor finishes complete all as specified and directed. MAKE: KAJARIA/H&R JOHNSON/CERA/ NITCO/SOMANY

M&L for (350mmx250mmx7mm/450mmx350mmx 7mm thick ) coloured glazed ceramic tiles set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments.(Note: Any disturbed surfaces shall be matched w/o any extra cost to the govt) incl 10mm thick rendering in CM 1:4 below tile for dado/skirting complete all as specified and directed by Engr-in-Charge. MAKE: KAJARIA/H&R JOHNSON/CERA/ NITCO/SOMANY

M&L for two coats cement base paint on newly plastered surfaces of wall including preparation of surfaces including curing before and after applying each coat complete all as specified and directed. MAKE : Snowcem/Asian/BERGER/DURACEM

M&L for preparing newly plastered surfaces of internal walls and applying three coats of white wash complete all as as specified and as directed.

Material & Labour 75mm thick PCC 1:3:6 type C1 (using 20mm graded stone aggregate) as in plinth protection and finished concrete surface even and smooth without using extra cement including making proper joints with bitumen mastic with sand as per specification at an interval of 3m complete all as specified and as directed.

S&F 0.63 mm thick corrugated Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 complete all as specified and directed. Make : SAIL/TATA/JSW STEEL

Mild Steel Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, conforming to Fe 410 -W (Gde- E- 250) quality-A complete all as specified and as directed

M&L 2nd class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the soild, rounded or chamfered, put together with glue pinned at joints, supplied and fixed plain fillets, square, rectangular or triangular in section clean swan, secured with nails or brads complete all as specified.

Factory made 35mm thick IInd Class Hard wood Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats, complete all as specified and directed by Engineer-in-Charge. MAKE: M/S WOOD PRODUCT INDORE/M/S GOYAL INDUTRIES CORPORATION 8743 DESH BANDHU GUPTA ROAD NEW DELHI/ M/S JAIN WOOD INDUSTRIES MURTHAL SONIPAT/M/S PIONEER TIMBER PRODUCT CHANDIGARH/M/S SHIV JOINERY& FURNITURE INDUSTRIES JAMMU/M/S M.S JOINERY WORKS, PARIMPORA, SRINAGAR

S & F 100mm Aluminium handles, cast type, anodised complete all as specified and directed by engineer in charge.

Butt hinges, medium weight, cold rolled mild steel and fixed with screws to wooden frames or with welding to existing MS frames, 75 mm size, ISI marked, complete all as specified and directed by Engineer-in- Charge.

S&F for Aluminum, anodized, barrel tower bolts, ISI Marked, of extruded section 100 mm long, complete all as specified and directed.

Preparation of new or previously untreated steel or steel based surfaces of any description not otherwise described not exc 10 cm in width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide or zinc chrome primer complete all as specified and directed by Engineer-in-Charge. MAKE: NEROLAC PAINTS/ JEHNSON & NICHOLSON/BERGER PAINTS/ICI DULUXE/ASIAN PAINTS

S&F PVC waste pipe 32 mm bore with cup and washers complete on new or old locations complete all as specified and as directed.

600 mm x 450 mm mirror of thickness 5/5.5mm of slected quality glass, mounted on 6 mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete, all as specified and as directed by Engr-in-Charge. MAKE: SAINT GOBAIN / MODI GUARD / TRIVENI FLOAT GLASS

Viterous china wash basin, white flat back size 600x 480mm including waste coupling CP 32mm dia and CI brackets of iron 65 x 65 x 6mm embedded in PCC block with PCC 1:2:4 type B-1 and PVC waste pipe 32mm dia & CP grating with holes complete, all as specified and as directed by Engr-in-Charge. MAKE: CERA/HINDWARE/PARRYWARE

PVC connections 15 mm size with PTMT nuts of length 600 mm complete, all as specified and diected by Engr-in-Charge. Make: Prayag/Polytuf/Supreme

15mm bore bib tap, (minmum weight 350 gms), chromium plated, fancy type, cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule complete, all as specified and directed by Engineer-in-Charge. MAKE: PARKO/MARC/ESS ESS/CERA

15mm bore pillar tap cast copper alloy chromium plated screwed downhigh pressure, with or without lettered 'hot or cold' with long screwed shanks and fly-nuts screwed for iron pipe complete, all as specified and directed by Engineer-in-Charge. MAKE: PARKO/MARC/ESS ESS/CERA

Chromium plated, fancy type Stop valve/cock, cast copper alloy, screwed down, high pressure with handle, chromium plated, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe complete, all as specified and directed by Engineer-in-Charge. MAKE: PARKO/MARC/ESS ESS/CERA

Rotational moulded polyethylene water storage tank, inner and out white, two layers, ISI marked (cylinderical vertical with closed top) hoisted with threaded cap and fixed in position all as specified in SSR Part-I of Capacity 500 litres each including all accessories (i.e GI nipples, etc), including provn of 20/15mm dia spout for connecting inlet, outlet, overflow and washout pipes complete, all as specified and as directed by Engr-in-Charge. MAKE: SINTEX/POLYWELL/ROTEX/POLYCON

S&F 15mm bore 3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass treaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc.complete all as specified. Make : JINDAL/KISAN/SFMC/Supreme/Kanha Plastic Pvt Ltd

S&F 20mm bore 3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass treaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc.complete all as specified. Make : JINDAL/KISAN/SFMC/Supreme/Kanha Plastic Pvt Ltd

S&F 20mm outer dia PPR Gate valve (Brass insert) confirming to ISO 2000 high pressure with epoxy coated aluminium rod and high density plastic ball screwed for PPR pipe or for union and fixed as per requirement of site completely all as specified and directed by the Engr-in-Charge. Make : JINDAL/KISAN/SFMC/Supreme/Kanha Plastic Pvt Ltd

S&F in repair 20mm outer dia PPR Ball valve (Brass insert) confirming to ISO 2000 high pressure with epoxy coated aluminium rod and high density plastic ball screwed for PPR pipe or for union and fixed as per requirement of site completely all as specified and directed by the Engr-in-Charge. Make : JINDAL/KISAN/SFMC/Supreme/Kanha Plastic Pvt Ltd

S&F grating doom 125 mm with waste hole of PTMT complete all as specified and as directed. Make: Prayag/Polytuf/Supreme

S&F PVC (SWR) pipe 110 mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floors cement complete all as specified. MAKE: SUPREME/ASHIRWAD/FINOLEX/ SFMC/ASTRAL

M&L 75 mm bore PVC (SWR) multi floor trap with grating including jointing with solvent cement complete all as specified and as directed. MAKE: SUPREME/ASHIRWAD/FINOLEX/ SFMC/ASTRAL

S&F PVC (SWR) pipe 75 mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floors cement complete all as specified. MAKE: SUPREME/ASHIRWAD/FINOLEX/ SFMC/ASTRAL

S&F 110mm bore PVC (SWR) pipe bends any radius complete, all as specified and as directed. MAKE: SUPREME/ASHIRWAD/FINOLEX/ SFMC/ASTRAL

S&F 75mm bore PVC (SWR) pipe bends any radius complete, all as specified and as directed. MAKE: SUPREME/ASHIRWAD/FINOLEX/ SFMC/ASTRAL

S&F 75mm bore PVC (SWR) junction single, (Single T) equal or unequal complete, all as specified and as directed. MAKE: SUPREME/ASHIRWAD/FINOLEX/ SFMC/ASTRAL

S&F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal complete, all as specified and as directed. MAKE: SUPREME/ASHIRWAD/FINOLEX/ SFMC/ASTRAL

S & F brass towel rail, 600mm long, chromium plated with a pair of brackets, fixed to wall with CP brass screw and PVC rowl plugs complete all as specified and as directed. MAKE: PARYAG/POLYTUF/SUPREME

M&L for 6mm thick ply wood (No of plys 05) BWR, type BB as in ceiling panelling fixed with nails to timber frame work, complete all as specified and as directed. Make : DURA PLY/GREEN PLY/DURO/BHUTAN BOARD/ CENTURY/DURIAN

M&L for 2nd class softwood clean sawn plain fillets, square,rectangular or triangular in section, clean sawn, secured with nails or brads exceeding 13 Sqcm and n.exc 25 Sqcm in section as in framed work complete all as specified and directed.

10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets with twin flush provision, complete, fixed in repairs all as specified and as directed by Engr-in-Charge. MAKE: Cera Model Combiflush twin flush as per Cat Part No. B1020101 (Old Cat Part No 2603) or equivalent in HINDWARE/PARRYWARE

Vitreous china water closet, 'Orissa' pattern, including lime concrete bedding, size 580 x 440 mm white with integral foot rests excluding flushing cistern and flush pipe but including connection to trap, anti syphonage pipe etc. complete fixed in repairs, incl bedding with PCC 1:2:4 type B-1 using 20 mm grade stone aggregate complete all as specified and as directed by Engr-in-Charge. Make: Cera/Hindware/Parryware

S&F sand cast iron 'P' or 'S' trap 110mm bore for Indian type water closet compele all as specified and directed

Preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over and including one coat of pink primer complete all as specified and directed by Engineer-in-Charge. MAKE: NEROLAC PAINTS/ JENSON & NICHOLSON/BERGER PAINTS/ICI DULUXE/ASIAN PAINTS

M&L for pre cast cement concrete block masonary of 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) with soild blocks, 10cm thick (with plain or interlocking joints as directed), set and jointed in cement mortor 1:6 complete all as spd and directed.

TMT mild steel bars, 6 to 8mm dia, as in stirrups, spacers and binders for reinforcemnent, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia), complete all as specified and as directed by Engineer-in-charge.

Use and waste of form work to floor or roof beams, beam haunch- ings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. etc to obtain rough flat finished surface of concrete complete all as specified and as directed.

Plain cement concrete 1:3:6 type C-0 using 12.50mm graded crushed stone aggregates as in Damp Proof Course and the like, complete all as specified and as directed by Engineer-in-charge.

Reinforced cement concrete 1:2:4 type B1, (using 20 mm graded crushed stone aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span and the like all as specified and as directed by Engineer-in-Charge.

M&L for plain cement concrete 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) 75 mm thick sub base, sub floor and pavings complete all as specified and directed.

M&L for plain cement concrete 1:2:4, type B-0 (using 12.50 mm graded crushed stone aggregate) 25 mm thick as in floors and the like including the finishing the surfaces even and rough complete all as specified and directed.

35mm thick, factory made 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete, all as specified and directed by Engr in Charge. Make : M/S WOOD PRODUCT INDORE M/S GOYAL INDUTRIES CORPORATION 8743 DESH BANDHU GUPTA ROAD NEW DELHI M/S JAIN WOOD INDUSTRIES MURTHAL SONIPAT M/S PIONEER TIMBER PRODUCT CHANDIGARH M/S SHIV JOINERY& FURNITURE INDUSTRIES JAMMU M/s M.S JOINERY WORKS, PARIMPORA, SRINAGAR

Plain Sheet glass 3.00 mm thick, ordinary quality and glazing with oil pane putty in squares not exceeding 0.5 Sq. mm in each pane, complete, complete all as specified and as directed.

S&F for Aluminum, anodized, barrel tower bolts, ISI Marked, of extruded section 150 mm long, complete all as specified and directed.

S & F 150mm extruded Aluminium handles, fabricated type, anodised complete all as specified and directed by engineer in charge.

Butt hinges, medium weight, cold rolled mild steel and fixed with screws to wooden frames or with welding to existing MS frames, 100 mm size, ISI marked, complete all as specified and directed by Engineer-in- Charge.

Mild steel sliding door bolts 300mm long, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed ISI marked complete all as specified and directed by Engr-in-Charge

S&F 25mm bore 3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass treaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc.complete all as specified. Make : JINDAL/KISAN/SFMC/Supreme/Kanha Plastic Pvt Ltd

Chromium plated, fancy type Stop valve/cock, cast copper alloy, screwed down, high pressure with handle, chromium plated, screwed end for iron pipe or for union and fixed, suitable for 25 mm bore pipe complete, all as specified and directed by Engineer-in-Charge. MAKE: PARKO/MARC/ESS ESS/CERA

Rotational moulded polyethylene water storage tank, inner and out white, two layers, ISI marked (cylinderical vertical with closed top) hoisted with threaded cap and fixed in position all as specified in SSR Part-I of Capacity 1000 litres each including all accessories (i.e GI nipples, etc), including provn of 20/15mm dia spout for connecting inlet, outlet, overflow and washout pipes complete, all as specified and as directed by Engr-in-Charge. MAKE: SINTEX/POLYWELL/ROTEX/POLYCON

Forming Contraction (Dummy) Joints 20 mm deep x 10 mm wide, filled with sealing compound grade A for plinth protection and the similar works, complete all as specified and directed.

S& F mild steel Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated and similar work conforming to Fe 290 Gd E 165 complete all as specified and as directed.

M&L for plain cement concrete 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) 75 mm thick sub base, sub floor and pavings complete all as specified and directed.

M&L for Chequred cement concrete tiles 30cm X 30cm X 20mm thick, set ,pointed & jointed in neat cement slurry in floors polished with grey cement & pigments .Layed over 20mm thick cement screed base (1:4) and all as directed by Engr-in -Charge. Make : NTC/NITCO/ULTRA /JOHNSON

M/S ADHISH ENGINEERS

R B TRADERS