DEMOLITION OF BLDG NO T/18 AND CONSTRUCTION OF TESTING FACILITY FOR RAMPAGE MISSILE AT NAD, GOA

Amount

SCHEDULE "A" Part - I (BUILDINGS & STRUCTURES WORKS) Total of Sch-'A' Part-I B/F from Serial Page No. 26 (RR )

SCHEDULE "A" PART-II (SITE CLEARANCE, AREA DEVELOPMENT, EXCAVATION & EARTHWORK) Total of Sch-'A' Part-II B/F from Serial Page No. 28 ( RR )

SCHEDULE "A" PART-III ( INTERNAL ELECTRIFICATION & FLAMEPROOF WIRING) Total of Sch-'A' Part-III B/F from Serial Page No. 32 (RR )

SCHEDULE "A" PART-IV (INTERNAL WATER SUPPLY) Total of Sch-'A' Part-IV B/F from Serial Page No. 33

SCHEDULE "A" PART-V ( ROAD & HARD STANDING ) Total of Sch-'A' Part-V B/F from Serial Page No. 34 (R )

SCHEDULE "A" PART-VI ( SEWAGE DISPOSAL ) Total of Sch-'A' Part-VI B/F from Serial Page No. 36 (RR )

SCHEDULE "A" PART-VII ( AREA DRAINAGE ) Total of Sch-'A' Part-VII B/F from Serial Page No. 37 (R )

SCHEDULE "A" PART-VIII ( EXTERNAL ELECTRIFICATION ) Total of Sch-'A' Part-VIII B/F from Serial Page No. 39 (RR )

SCHEDULE "A" PART-IX (EXTERNAL WATER SUPPLY) Total of Sch-'A' Part-IX B/F from Serial Page No. 41 (RR )

SCHEDULE "A" PART-X ( FIRE ALARM SYSTEM ) Total of Sch-'A' Part-X B/F from Serial Page No. 42

SCHEDULE "A" PART-XI ( LIGHTNING PROTECTION ) Total of Sch-'A' Part-XI B/F from Serial Page No. 43

SCHEDULE "A" PART-XII ( AIR CONDITIONING ) Total of Sch-'A' Part-XII B/F from Serial Page No. 44 (R )

SCHEDULE "A" PART-XIII ( EOT CRANE ) Total of Sch-'A' Part-XIII B/F from Serial Page No. 45

SCHEDULE "A" PART-XIV ( DEMOLITION / DISMANTLING ) Total of Sch-'A' Part-XIV B/F from Serial Page No. 46 ( R)

SCHEDULE "A" PART -XV (MISCELLANEOUS ITEMS)

EXCAVATION & EARTHWORK

Removing excavated material (any type) and depositing it outside Ministry of Defence Land. Notes (i) Before quoting the tender, the bidders are advised to ascertain the distance outside MD and, at which the excavated material/ debris are to be disposed off. No extra claim what-so-ever shall be entertained on this account. (ii) This item shall be considered as per the requirement at site. (iii) All excavation earthwork covered under Sch 'A' part III to part XV shall be measured and paid under this item.

TRAVERSE WALL

Material and labour for two coats of cement based paint over a coat of primer complete all as specified and directed.

Supply and lay sweet soil / good earth brought from outside of MOD land to a uniform thickness of 15 cm mixed with approved manure in a ratio of 2:1 including watering , spreading and levelling complete all as specified and directed.

Material and labour for development of lawn area and planting of carpet grass or any other approved grass as approved by GE including watering and uniform green surface complete including site levelling etc and watering for a period of 90 days and uniform cutting so as to give a uniform green surface complete all as specified and directed.

INTERNAL ELECTRIFICATION

S & F LED Security/Street light fittings 25 Watt wall mounting type extruded metal/aluminium body, and electronic LED driver, ect. with all accessories internal prewired & including connecting up with 2 core flexible cppper conductor cable with suitable size etc. including Fabricate,supply & fix GI pipe bracket 25mm dia- 0.9m long & 2 set of clamps made out of 30x5mm ms flat & fixed with anchor bolt suitable for 25w security light fitting all as specified & directed.

S & F LED light fittings 1X9 W / 1X10 W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size etc. with all accessories all as specified & directed.

S&F Heavy duty Exhaust fan of size 450 mm sweep metal body complete with and louvers connecting up including provision of three core flexible copper wire of size 23/0.0076 from ceiling rose to exhaust fan.

S&F Energy efficient BEE five star rated ceiling fan, 1200 mm sweep and connecting up including provision of three core flexible copper wire of size 23/0076 from ceiling rose to ceiling fan complete in all respect all as specified and directed.

S & F MCCB DB VERTICAL TYPE , suitable for 125 amps MCCB as incommer,made of sheet steel , powder painted with NUTRAL bus bar 200 A, neutral link, IP-43-IK09 protection grade , 415Volts TPN with 4 way Double door , L&T CAT NO-DBVTL004DD/ LEGRAND CAT NO-607913/ / schneider/ ABB ( incoming for VTPN DB lighting DB & Stabilizer DB)

M & L for Copper strip 32 x 6 mm as earth continuity conductor 600 mm long, duly drilled with 10 mm dia hole in every 50 mm on entire strip for taping earthing ,fixed on wall with PVC insulated back plate/FRP Insulator at 250 mm distance with copper nuts and bolts including anchor fastner pin type complete all as specified and directed. ( for ESD Flooring)

Earthing complete with galvanized steel earth plate electrode 600mm x600 mm x 6mm buried directly in ground vertically to a depth not less then 2.25 meter below normal ground level with top edge of the plate not less then 1.50 meter below normal ground level connected to galvanized earth wire 4.00mmdia by means of bolts ,nuts ,check nuts and washers complete up to and including test point made out of 40 x 6mm alum flat including earthing pit , charcoal common salt ,Earthing lead 4.00mm dia up to 7.5m, 20mm dia medium grade GI watering pipe ,G.I. protection pipe 15 mm dia up to 7.5m long,,PPC pit in PCC 1:2:4 type B-1 using 20 mm graded stone aggregate ,PCC pit cover including necessary excavation & earth work complete all as shown in electrical plate No-5 of SSR-2009 (part-I) [ Int Elect 02 +

Supply and fixing of Chemical earthing with copper earth plate 90 cm x 60cm x5mm buried directly in ground vertically to a depth not less then 2.25 meter below normal ground level with top edge of the plate not less then 1.50 meter below normal ground level connected to copper strip 32x 6mm by means of bolts ,nuts ,check nuts and washers complete up to and including test point made out of 40 x 6mm alum flat including earthing pit , charcoal -250kg,common salt-250 -kg and Magnesium sulphate -100 kg ,earth strip 32x 6mm up to 7.5m, 20mm dia medium grade GI watering pipe ,G.I. protection pipe 40 mm dia up to 7.5m long,,PPC pit in PCC 1:2:4 type B-1 using 20 mm graded stone aggregate ,PCC pit cover including earth work complete all as shown in electrical plate No-5 of SSR-2014 (part-I) [ Int Elect 04 + Ext Ele 14 + 06 LP + 06 DG set +

S & F fresh air exhaust fan 230 mm sweep PVC body complete with and louvers connecting up including provn of 3 core flexible copper wire of size 23/ 0.0076 from mceiling rose to exhaust fan as specified and directed by Engr-in-Charge

ROAD AND HARD STANDING

M&L for cement concrete type B-1 , M-20 design mix as in flooring/ hard standing with using dewatering complete all as specified and directed.

Extra for vacume dewatering of concrete for item No 17.10 above

EXTERNAL ELECTRIFICATION

Boring of holes under road, pavement, hard standing by trenchless technology using ultra sounding technique and necessary machine including HDPE pipe of 150 mm dia suitable for 0.4 mpa working pressure

Supply, install, testing and commisioning of dIstribution transformer ( Level- 3 ) mounted on floor stepdown , 11KV/0.433KV , Three Phase complying with IS: 1180/IEC-76(Part-1) 2014 with latest ammanmendts , indoor type double copper wound suitable for 50 Hz system of capacity 160 KVA, oil immersed naturally cooled delta connected on HT side and Star connected on LT side ,Vector Group Dyn11, provided with OFF load tap changer to vary secondary voltage from -7.5% to + 7.5 % in steP of 2.5 %. Losses should be confined to the limits specified as follows: :maximum allowable losses at full load (100 % ) & Half Load ( 50 % )shall not be exceeded 1.38 % & 0.96 % Respectivly as per GRlHA RATING, Percentage Impedance: 5%. Losses and Impedance are subjected to tolerance as specified in IS 1180. The transformers should be supplied with first filling of oil confirming to IS 335 .The transformer should have both side cable end box with neutral brought out complete all as directed by Engineer - in -Charge, and installation of transformer shall be carried out as per IS-10028 and comprising with the following standerd fittings/Technical specifications : -

(a) Lifting lug for transformer and tank.

(b) Earthing terminal rating and diagram plate.

(c ) Air release device.

(d) Oil filling inlet pipe with plug.

(e) Drain outlet pipe with brass gate valve.

(f) Conservator tank with oil level indicator

(g) Silica jel breather

(j) First fill of oil upto level including conservator tank with fresh new oil conforming to IS335.

(k) Type of connection Delta/Star

(l) Type of cooling: Oil and Natural Air.

(m) Vector group:DYN 11.

(n) Temperature rise over an ambient of 50 °C maximum.

(o) Cable end box on both side for HT/LT cables of suitable size.

(p) Provision of thermometer with pocket.

(q) Provision of oil and winding temperature gauge.

Taking down steel tubular/PCC pole of any size including insulater & cross arm & stay wire & refixing at new location as directed by engr-in -charge including necessary excavation/earth work & PCC.

Disconnecting LT panel outdoor type for shifting at other location including connection and restore of electric supply icluding foundation and all accessories as directed by engr-in -charge.

Disconnecting and relaying of under ground cable of any size any core including connection and any accessories ie ,jointing, lugs required at site to the connection for other location for connection and restore of supply and all accessories all as specifies and as directed by Engr in Charge

Supply, Installation, test and Commissioning, factory fabricated LT panel board, type tested by CPRI /Authorised Govt. Agencies , confirming to IEC 60349-1 & 2,up to 400 Amps incommer OR confirming to IEC 61349-1 & 2, above 400 Amps incommer, LT panel board made out of 2 mm thick GI Sheet multifold design, chemically treated surface with multi tank process powder coating, indoor modular type,dust free ,Vermin Proof , totally enclosed with Confirming to IP 43 for indoor panel & Confirming to IP 54 for outdoor panel ,single door with both side opening including Neoprene Rubber Gasket, suitable for 440 Volt 3 Phase 4 Wire System, including Danger Plate, Earthing Strip Point and Ventilation Louvers at Rear Side, Bottom detachable Gland Plate complete with suitable size Zinc Chromium Plated Nuts, Bolts and Washers, etc. and embedded with 50X50X6mm Galvanised iron Angle Frame and 750 mm above the Normal Ground Level complete with internal connection with suitable size of cable, cable lugs and cable glands PCC Foundation in Cement Concrete 1:3:6 (20 mm Graded Stone Aggregate) and Testing after Installation including complete all as specified and comprising of the following :– Make of panel board - L&T / ABB / Schneider/Seimens or by their authorised channel partners duly authenticated by th company. (main Panel )

(a) MCCB 250 Amps, 4 Pole, 415V,35 KA Thermal Magnetic Release Manual-01 No

(b) Aluminium Busbar TPN 400 amps - 01 set

OUTGOINGS:-

(a) MCCB 200 Amps, 3 Pole, 415V,35 KA Thermal Magnetic Release Manual-02 No (For DG AMF & Spare)

(b) MCCB 3 Pole, 100 A, 35KA, thermal magnitic Release Manual - 01 (APFC Panel)

(e) Phase indicating lamps RYB for incoming and each outgoing connection.

Supply, Installation, test and Commissioning, factory fabricated LT panel board, type tested by CPRI /Authorised Govt. Agencies , confirming to IEC 60349-1 & 2,up to 400 Amps incommer OR confirming to IEC 61349-1 & 2, above 400 Amps incommer, LT panel board made out of 2 mm thick GI Sheet multifold design, chemically treated surface with multi tank process powder coating, indoor modular type,dust free ,Vermin Proof , totally enclosed with Confirming to IP 43 for indoor panel & Confirming to IP 54 for outdoor panel ,single door with both side opening including Neoprene Rubber Gasket, suitable for 440 Volt 3 Phase 4 Wire System, including Danger Plate, Earthing Strip Point and Ventilation Louvers at Rear Side, Bottom detachable Gland Plate complete with suitable size Zinc Chromium Plated Nuts, Bolts and Washers, etc. and embedded with 50X50X6mm Galvanised iron Angle Frame and 750 mm above the Normal Ground Level complete with internal connection with suitable size of cable, cable lugs and cable glands PCC Foundation in Cement Concrete 1:3:6 (20 mm Graded Stone Aggregate) and Testing after Installation including complete all as specified and comprising of the following :– Make of panel board - L&T / ABB / Schneider/Seimens or by their authorised channel partners duly authenticated by th company. (DG Panel )

(a) MCCB 200 Amps, 4 Pole, 415V,35 KA Thermal Magnetic Release Manual-01 No

(b) Aluminium Busbar TPN 400 amps - 01 set

OUTGOINGS:-

(a) MCCB 100 Amps, 3 Pole, 415V,35 KA Thermal Magnetic Release Manual-01 No (AC Plant panel )

(b) MCCB 3 Pole, 63 A,35KA, thermal magnitic Release Manual - 04 (Bldg Panel VTPN, Voltage Stablizer,crane Panel & Spare)

(e) Phase indicating lamps RYB for incoming and each outgoing connection.

Supply, installation, commissioning and testing the following Vacume Circuit breaker 11 KV, 3 phase 50 cycle ( 50 HZ) totally enclosed metal clad switch gear panel factory made, powder coated board with indoor vacuum circuit breaker floor mounted with common copper tinned bus bar complete all as specified

VCB PANEL EACH CONSISTING OF THE FOLLOWING EQUIPMENT :-

(a) One No 400 Amps capacity triple pole metal clad HT control panel totally enclosed extendable pattern air insulated metal clad housing, floor mounting vertically isolated, vermin proof, fully interlocked horizontal draw out type having double isolation features & control device with grounded neutral system and equipped with the following equipment.

(i) One set of 3 phase 400 Amps air insulated, tinned copper bus bar with insulated colour coating.

(ii) One set of side frame for housing for circuit breaker carriage.

(iii) 6 Nos 630 amps isolators plugs.

(iv) One set of mechanical interlock and automatic shutter system,

(v) One 630 Amp triple pole 400 MVA rupturing capacity VCB with automatic drop out and manually charged and motor operated spring closed mechanism complete with auxiliary switches, truck mounted draw out, vacume circuit breaker, incorporating mechanical as well as electrical ON/OFF indication, mechanical indication "ON" push button for emergency trip & 30 Volts DC trip coil.

(vi) One cable box suitable for reception for 120/95 sqmm HT XLPE 3 core under ground cable 11000 volts pressure.

(vii) 03 Nos double wound current transformer dual ratio 150/100/ 5-5 amps for protection and metering having adequate VA burden and accuracy.

(viii) One set of 4 Nos LED lamp for indicate ON/OFF/Trip/charging.

(ix) One 3 phase horizontal draw out type voltage transformer 100 VA burden and accuracy mounted on the draw able housing for 11000 volts/ 110 volts with protection fuse.

(xii) One set of 3 pole micro process relay 3 phase over current , earth fault relay MC – 61 CNX Make L&T. suitable for incoming panel.

(xiv) One No volt coil to trip the VCB on failure of electric supply.

(xv) One set of mechanical interlock and automatic shutter gear.

(xvi) 230 volts AC single phase 80 watt rated strip heater with switch and thermostat space heating.

(xvii) Provision of 30 volts DC tripping system with suitable power pack including, siren/ horn alarm and accept switch and over voltage protecting relay.

(xviii) Provision of motor charging with AC motor.

(xvix) Inbuild Power pack 30 v dc to be provided with panel at least for 30 minuite Back Up.

Supply and fix cable route indicator made of round CI disc embossed LT Cable, of size 16cm dia 6mm thick duly revited with angle of size 50x50x4mm and 60cm long including PCC 1:2:4 B1 using 20mm aggregate 15cm x 15cm x 15cm for grouting the same complete all as specified.

Supply and fix cable route indicator made of round CI disc embossed HT Cable, of size 16cm dia 6mm thick duly revited with angle of size 50x50x4mm and 60cm long including PCC 1:2:4 B2 using 20mm aggregate 15cm x 15cm x 15cm for grouting the same complete all as specified.

Supply, Installation, test and Commissioning CPRI APPROVED factory fabricated, indoor type, APFC capacitor bank Panel Board of size as recommended by manufactrer 30KVAR with 6 steps ( 5+ 5+5+ 5+5+ 5) WITH MD-XL CAPACITOR AND MCCB AS INCOMER Automatic Power Factor Correction panel , made out of 2 mm thick CRCA Sheet Dust and Vermin Proof, single door with both side opening including Neoprene Rubber Gasket, suitable for 440 Volt 3 Phase 4 Wire System,The enclosure shall be pre-treated as per 11 tanks process and finished with powder coating of shade RAL 7032. , including Danger Plate, Earthing Strip Point and Ventilation Louvers at Rear Side, Bottom detachable Gland Plate complete with suitable size Zinc Chromium Plated Nuts, Bolts and Washers etc. and embedded with 50X50X6mm Mild Steel Angle Iron Frame and 750 mm above the Normal Ground Level complete with internal connection with suitable size of cable, cable lugs and cable glands PCC Foundation in Cement Concrete 1:3:6 (20mm Graded Stone Aggregate) and Testing after Installation complete all as specified .The panel shall be factory fabricated comprosing of following. Make of pannel L&T/ SCHNEIDER/ABB

Particulars

INCOMER

MCCB 100 A 35 KA,4 POLE ,thermal magnetic relese, Ics=100% Icu & L&T /Legrand /schneider - 1 no (Thermal Magnetic Release)

ROM+SPDR - 1 no

Auxiliary 1 c/o +TAC 1 c/o- 1 no

OUTGOING CAPACITOR FEEDERS : -

5 KVAr Capacitor feeder comprising of:- (6 Nos. )

16A, BUSSMANN FUSE 18 nos

Thyristor switching module 10kVAR, 440V,TSM,LTTSM -6

7% Detuned Aluminium Reactor 5 KVAr 440V,LTAL,CAT NO-0712B2-6 no

Ultra heavy duty capacior LTXL , BOX type oil Filled Capacitor bank 7.5 kVAr,sutable for 480V ,LTXL- 6nos

Push Button ON/OFF -12nos

Indicating lamps 12 NOS

Auxiliary Contactor {2NO+2NC} 24V DC Coil Voltage MXO- 6

6A DP MCB , C CURVE 6 NOS

Incomer Metering

APFC relay 6 stage {BLR CM – 06T MB } -1 NO ,[230/ 110 V, 1/5A, 50 Hz] [Transistor output + Single CT sensing + RS 485 MODBUS]

Digital Voltmeter (3Ph, Class 1) -1 NO

Digital Ameter (3Ph, Class 1, 5A) -1 NO

Metering CT --/5A, Class-1- 3 NOS

SMPS 5A, Input 230V AC Output 24V DC -1 NO

ON Delay Timer 0-10 Sec.,Coil 24V DC -1 NO

Auxiliary Contactor {4NO} with 24V DC}-3 NOS

Indicating Lamp(R,Y,B)-3 NOS

6A SP MCB-3 NOS

6A DP MCB

6A FP MCB -1 NO

8" {EBM NADI} Fan -1 NO

EXTERNAL WATER SUPPLY

Supply and lay spigot/flanged/ socketed DI fittings. Such as bends (any type radius and angle), tapers, tees, collars & tail piece socket/flanged/spigot etc of size up to 300mm dia.

Supply and laying pipe Ductile Iron, with spigot and socket ends centrifugally K-9 , of size 150 mm dia all as specified and directed by Enger in charge

Supply and laying pipe Ductile Iron, with spigot and socket ends centrifugally K-9 , of size 200 mm dia all as specified and directed by Enger in charge

Construction of brick masonry valve chamber of size 900 x 900 x 900 mm (internal dia) suitable for 150 mm dia valve with necessary earth work excavation, plain cement concrete (1:4:8 )using 40 mm graded stone aggregate, 75 mm thick in cement mortar ( 1:6 ), 15 mm thick plastering (1:6) internally including flooring and externally upto 15 mm below ground level, plain cement concrete 1:4:8 type B1 using 20 mm graded stone aggregate in coping, MS sheet cover made out of 3mm thick MS sheet' flat iron frame and bracing with locking arrangement, applying two coats of synthetic enamel paint including dismantling removing the existing damage chamber completely, removal of debris & depositing all as specified & directed by Engr-in-charge [EXT WS 01]

FIRE ALARM SYSTEM

M & L for Beam Master Detector, Transceiver Type including power supply unit & module

Read-M & L for Low smoke Zero helogen flame retardent fire alaram cable 2 core, 1.5 mm² copper conductor confirming to BS7629-I , BS6387 & rated for 500 v grade having plaine sraded copper coductutor with priming insulation of glass mica fire resistance tape & secondery insulation of high performance silicon rubber with electrostatic screen of aluminium fire barrierType LT53 outer sheathconfirming to BS 7655 , red in colourdrawn through & including concealed steel conduit including laying,fixing,connecting complete all as specified and directed.

Supply and Fixing ERW metallic conduit 25 mm dia inclusive of boxes (junction/ terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe

Supply and fix fire alarm control repeater panel complying with BS EN 54 2 loop panel of capacity from 99 detectors & 99 modules upto 200 detectors and modules.

AIR CONDITIONING

Supply, installation, testing & commissioning Split Air Conditioner 2 Ton, 5 star rating, inverter type technology, 230 V, 50 Hz, refrigerant -R32, single phase, indoor/ outdoor unit complete with cordless remote control unit and compressor- inverter rotary type, condenser-100% Copper type, noise level outdoor-60 dB and high cooling performance and desirable cooling mode for different types of climate. Make- Blue star/Voltas/LG

Supply and fixing of voltage stabilizer for automatic operation single phase naturally air cooled indoor type and designed for input variaiton between 170volt to 250volt with output voltage stabilised at 230Volt with accuracy of ± 2.5% and of capacity of 5.0 KVA.

INTERNAL ELECTRIFICATION ( FLAME PROOF )

Supply & fixing Flame Proof Wall mounting fan 610 mm sweep high speed, thermally protected motor, heavy duty gear box, 90 degree oscillation for wide coverage conforming to IS-2997-1964 all as specified and directed by Engineer-in-Charge. , Make-Sudhir /Havells/Crompton Greaves/Bajaj/Orient

EOT CRANE

Design ,supply, install, testing and commissioning of indoor type flame proof EOT (electrically operated travelling) double girder over head crane of 2 Ton capacity, class III, M7 as per IS:3177 of 2020 and IS : 807 of 2006 and other relevant Indian standards of latest versions having straight travel path, operating on 415 volts, 3 phase, 50Hz, AC and with control voltage not exceeding 110 volts, AC through low voltage transformer with independent movable pendent supported by chain/SS rope, double girder type , floor operated movable pendent control by means of push buttons independent of crab trolly position with protective panel with down shop lead, trailing cable complete with minimum IP-55 protection for cables, motors panels incl separate canopy for for motors alongwith all accessories/equipments duly epoxy painted complete all as stipulated in Annexure-'A' here in after , as shown on drawings and as directed. The span length ,cross travel length & hook height mentioned is tentetive exact span length ,cross travel length & hook height shall be measured at site before fabrication. ( for Test Cell)

EOT crane shall be provided with the following specifications and capable for electrically controlled movements: (i) Capacity of Crane : 2 Ton double box girder (ii) Clear span : 7.5 m (approx) (iii) Bay length : 9.5 m approx (iv) Hook height : 4 m approx (v) Hoisting speed : 3.0 mtr / min with creep control (vi) CT speed : 5.0 mtr/ min with creep control (vii) LT speed : 10.0 mtr/min with creep control (viii) Control; Pendent control, (A) MOTORS :- All the motors are Crane duty, squirrel cage type for Hoisting, LT & CT and will be 40% CDF with F Class insulation as per IS 325 latest edition. (i) One No. electric motor, Squirrel cage, 6 Pole crane duty IS:325 suitable capacity as per OEM of suitable HP (main Hoist) hoisting/lowering purpose.(ii) One No. electric motor, Squirrel cage, 6 Pole crane duty IS:325 suitable capacity as per OEM of suitable HP for cross travel motor.(iii) Two Nos. electric motor, Squirrel cage, 6 pole crane duty IS:325, of suitable capacity as per OEM of suitable HP for long travel motor. (B) Provision of “Down shop Lead” as per following specification:- Designing, manufacturing, supplying, Installation in position, testing and commissioning of 4 bar ‘U’ type galvanized iron conductor shrouded bus bar system of red, Yellow, Blue & Green complete with fully articulated sliding type ‘D’, metallic crane duty current collectors, duty fitted with sintered copper graphite cartridge with square bar, including designing suitable MS fabricated supports for mounting hanger clamps, splice covers, feed Kit, anchor clamp and covers all suitable for 2.0 Tonne EOT Crane.

(C) BRAKE:- AC Electromagnetic brake having suitable size, one No for cross travel and two Nos long travel, one No additional Electro Hydraulic thruster brake for the hoisting motion complete all as specified. (D) ROPE DRUM:- The rope drum is Mild steel fabricated and stress relived fabricated/seamless pipe with full length with specially designed flexible coupling between Hoist Gear box & rope drum. (E) Wiring and cables etc as required upto the Panel board.

NOTES

a) The crane is to be operated in indoor as well as outdoor fully exposed to weaether elements. Adequate IP protective covering over the electrical and mechanical components shall be provided

b) The crane shall be provided with additional storm brakes for anchoring it to cater to storm conditions

c) Automatic electrohydraulic or electromagnetic brakes shall be provided if the service brakes are not electromechanical type.

d) Unit rate quoted shall be deemed to include provision of electrical wiring of suitable size in rigid metallic conduits fixed on surfaces from main switch upto electrical control panels. All cables shall be armoured copper cables. Provision of ISMC channel welded along with ISMB (gantry girder) and longitudinal travelling rail welded alongwith ISMC.inclusive all supports ,MS insulators & other fittings & fixture as reqd.

e) Clear span and bay length specified and shown on drgs are only indicative. The tenderer shall visit the site and ascertain exact span and bay length before designing / execution.

f) Long traval main grantry girder will be provided by Building Contractor

g) Dimensions,capacities/sizes of equipments/ accessories mentoned on drawing are minimum to be provided. Prior approval of Accepting Officer shall be obtained for the detailed construction drg and electrical wiring diagram of EOT crane and contractor shall incorporate changes wherever required and the rates quoted above shall deemed to inclusive of such provisions and its accessories before designing / execution.

h) Longitudinal / cross travel shall be limited to 1.0 m away from the wall on both ends as far as possible.

j) The lowest bidder shall prepare Constructional drawing including specification as per the design of approved OEM. In case the lowest bidder is not OEM himself then lowest bidder shall submit an MOU with departmentally approved OEMfor construction and executing of the crane work. Drawings and specifications in both the cases will be subject to approval of accepting officer as per Para (g) above.

k) Any technical clarifications regarding size, capacity, rating and specification and drawings may please be clarified by the bidder from the E-4 section of this office before the Bid is submitted, he should also visit the site where the crane are being installed before submitting the Bid.

Note-2 The cranes shall be tested stage wise for 25%,50%, 75% 100% and 25% overload , The rates for all manpower and material and testing arrangement required will be deemed to be included in quoted rates and nothing extra will be admissible on this account.

Note 3-Gaurds will be provided with approch ladder on both sides of Long traval at a suitable level and ladders should have landing paltforms at both end with guards and side railing.

Note 4- If Any work not specified above, but considered necessary for efficient installation , working and performance of EOT Crane Shall be deemed to be included in quoted rate.

Design ,supply, install, testing and commissioning of indoor type flame proof EOT (electrically operated travelling) double girder over head crane of 2 Ton capacity, class III, M7 as per IS:3177 of 2020 and IS : 807 of 2006 and other relevant Indian standards of latest versions having straight travel path, operating on 415 volts, 3 phase, 50Hz, AC and with control voltage not exceeding 110 volts, AC through low voltage transformer with independent movable pendent supported by chain/SS rope, double girder type , floor operated movable pendent control by means of push buttons independent of crab trolly position with protective panel with down shop lead, trailing cable complete with minimum IP-55 protection for cables, motors panels incl separate canopy for for motors alongwith all accessories/equipments duly epoxy painted complete all as stipulated in Annexure-'A' here in after , as shown on drawings and as directed. The span length ,cross travel length & hook height mentioned is tentetive exact span length ,cross travel length & hook height shall be measured at site before fabrication. ( for Containing & Decontaining Room)

EOT crane shall be provided with the following specifications and capable for electrically controlled movements: (i) Capacity of Crane : 2 Ton double box girder (ii) Clear span : 3.5 m (approx) (iii) Bay length : 9.5 m approx (iv) Hook height : 4 m approx (v) Hoisting speed : 3.0 mtr / min with creep control (vi) CT speed : 5.0 mtr/ min with creep control (vii) LT speed : 10.0 mtr/min with creep control (viii) Control; Pendent control,

(A) MOTORS :- All the motors are Crane duty, squirrel cage type for Hoisting, LT & CT and will be 40% CDF with F Class insulation as per IS 325 latest edition. (i) One No. electric motor, Squirrel cage, 6 Pole crane duty IS:325 suitable capacity as per OEM of suitable HP (main Hoist) hoisting/lowering purpose.(ii) One No. electric motor, Squirrel cage, 6 Pole crane duty IS:325 suitable capacity as per OEM of suitable HP for cross travel motor.(iii) Two Nos. electric motor, Squirrel cage, 6 pole crane duty IS:325, of suitable capacity as per OEM of suitable HP for long travel motor.

(B) Provision of “Down shop Lead” as per following specification:-Designing, manufacturing, supplying, Installation in position, testing and commissioning of 4 bar ‘U’ type galvanized iron conductor shrouded bus bar system of red, Yellow, Blue & Green complete with fully articulated sliding type ‘D’, metallic crane duty current collectors, duty fitted with sintered copper graphite cartridge with square bar, including designing suitable MS fabricated supports for mounting hanger clamps, splice covers, feed Kit, anchor clamp and covers all suitable for 2.0 Tonne EOT Crane.

(C) BRAKE:- AC Electromagnetic brake having suitable size, one No for cross travel and two Nos long travel, one No additional Electro Hydraulic thruster brake for the hoisting motion complete all as specified.

(D) ROPE DRUM:- The rope drum is Mild steel fabricated and stress relived fabricated/seamless pipe with full length with specially designed flexible coupling between Hoist Gear box & rope drum.

(E) Wiring and cables etc as required upto the Panel board.

a) The crane is to be operated in indoor as well as outdoor fully exposed to weaether elements. Adequate IP protective covering over the electrical and mechanical components shall be provided

b) The crane shall be provided with additional storm brakes for anchoring it to cater to storm conditions

c) Automatic electrohydraulic or electromagnetic brakes shall be provided if the service brakes are not electromechanical type.

d) Unit rate quoted shall be deemed to include provision of electrical wiring of suitable size in rigid metallic conduits fixed on surfaces from main switch upto electrical control panels. All cables shall be armoured copper cables. Provision of ISMC channel welded along with ISMB (gantry girder) and longitudinal travelling rail welded alongwith ISMC.inclusive all supports ,MS insulators & other fittings & fixture as reqd.

e) Clear span and bay length specified and shown on drgs are only indicative. The tenderer shall visit the site and ascertain exact span and bay length before designing / execution.

f) Long traval main grantry girder will be provided by Building Contractor

g) Dimensions,capacities/sizes of equipments/ accessories mentoned on drawing are minimum to be provided. Prior approval of Accepting Officer shall be obtained for the detailed construction drg and electrical wiring diagram of EOT crane and contractor shall incorporate changes wherever required and the rates quoted above shall deemed to inclusive of such provisions and its accessories before designing / execution.

h) Longitudinal / cross travel shall be limited to 1.0 m away from the wall on both ends as far as possible.

j) The lowest bidder shall prepare Constructional drawing including specification as per the design of approved OEM. In case the lowest bidder is not OEM himself then lowest bidder shall submit an MOU with departmentally approved OEMfor construction and executing of the crane work. Drawings and specifications in both the cases will be subject to approval of accepting officer as per Para (g) above.

k) Any technical clarifications regarding size, capacity, rating and specification and drawings may please be clarified by the bidder from the E-4 section of this office before the Bid is submitted, he should also visit the site where the crane are being installed before submitting the Bid.

Note-2 The cranes shall be tested stage wise for 25%,50%, 75% 100% and 25% overload , The rates for all manpower and material and testing arrangement required will be deemed to be included in quoted rates and nothing extra will be admissible on this account.

Note 3-Gaurds will be provided with approch ladder on both sides of Long traval at a suitable level and ladders should have landing paltforms at both end with guards and side railing.

Note 4- If Any work not specified above, but considered necessary for efficient installation , working and performance of EOT Crane Shall be deemed to be included in quoted rate.

M & L Earthing complete with copper earth plate electrode 600mm x600 mm x 3.15mm buried directly in ground vertically to a depth not less then 2.25 meter below normal ground level with top edge of the plate not less then 1.50 meter below normal ground level connected to copper strip 20X3 mm lead by means of bolts ,nuts ,check nuts and washers complete up to and including test point made out of 40 x 6mm alum flat including earthing pit , charcoal common salt ,copper strip 20 X 3mm lead up to 7.5m, 20mm dia medium grade GI watering pipe ,G.I. protection pipe 15 mm dia up to 7.5m long, 40mm GI pipe from earth electrode to ground level and PPC pit in PCC 1:2:4 type B-1 using 20 mm graded stone aggregate ,PCC pit cover including earth work complete all as shown in electrical plate No-5 of SSR-2014 (part-I)

DG SET

(a) Supplying, installing, testing and commissioning, factory assembled silent Diesel Engine driven generator set, fully wired alternator AC to give an out put of 125 KVA continuously rating at a power factor 0.8 lagging, 3 phase 4 wire, 415 volts 50 Hz , 1500RPM, directly coupled with diesel engine liquid cooled mounted on common base frame complete with floor mounting fuel tank (service tank) of adequate capacity with fuel line & accessories, PCC foundation work as per manufacturer's instructions, vibration damper pads, control panel & other accessories etc and comprising of following.

(b) Diesel Engine: Liquid cooled turbo charged with after cooler to deliver suitable BHP at 1500RPM under NTP conditions of BS 5514 and conforming to IS 10002, DIN 6271 & ISO 9001:2008 with an overload capacity of 10% for one hour in any 12 hours continuous operation with the following accessories:. Diesel engine of rated speed at full load electric start developing with system with radiator and including electronic governor control of class A1, engine control panel, lub oil pump, water pump, fuel tank, exhaust pipe with silencer and suitable for electric start with batteries of adequate capacity and suitable for alternator of specified capacity complete with fly wheel direct/flexible coupling and coupling guard complete.

(a) Radiator with blower fan or heat exchanger with guard. (b) Pipe coupling for engine cooling system piping. (c ) Corrosion inhibitor coolant (d) Paper element filters (i) Fuel filter (ii) Lube oil filter (iii) By pass (e) Fly wheel housing and fly wheel to suit alternator. (f) Engine bearing mechanism in fly wheel housing. (g) Shut off coil with safeties for LLOP/HWT/over speed. (h) Dry type air cleaners and vacuum indicators. (j) Residential silencers. (k) Stainless steel exhaust flexible bellows. (l) Motor driven priming pump. (m) Battery charging alternator.

(n) Exhaust piping made out of STIC C class, MS pipe inclusive of all accessories and hardware, necessary supports scaffolding as per manufacturer's recommendations to sustain back pressure with rain cap. (o) Mineral wool insulation 2 inch thick suitable for 400 degree Celsius temperature cladded with aluminium sheet o 30 gauge for the entire length of exhaust pipe. (p) First fill of oil, coolant and diesel during commissioning and 12 hours testing. (q) Interconnecting copper cabling of adequate capacity batteries control. (r ) Fuel pipe class STIC 1" /1.5" /2" dia - 01 lot (s) Self starter 12 volts DC. (t) Electric operated electronic governor. (u) Fuel injection pump.

(v) Electronic instrument panel, complete with all accessories as per manufacturer's specifications displaying the following:- (i) 12 V Battery. (ii) Water temperature. (iii) lubricating oil pressure. (iv) Engine speed -1500 RPM (v) Engine hours (vi) Frequency. (vii) Voltage. (w) Safety control (Trip and indication). (i) High water temperature (ii) Low lube oil temperature (iii) Overspeed stop

(x) Base frame: Sturdy, fabricated welded construction, channel iron base frame (duly painted) for mounting engine and alternator as per manufacturer's design alonwith AVM pads. (y) Battery:-12 volts DC, 180AH, maintenance free battery conforming to IS:14257 with leads & terminals (Make- Excide/Amron). (z) Fuel tank: 10 hrs. full load diesel storage capacity fuel tank with mounting brackets factory made of 5 mm thick HR/MS sheet with level indicator fuel inlet, fuel outlet, air vent, drain plug, in let arrangement for diesel filling fro exterior canopy (without opening its panel) etc complete all as specified and directed.

(c) Alternator: Suitable rated 125 KVA, 0.8 pf , 415 volts, 3 phase, 4 wire, 50 Hz at 1500 RPM, self excited and self regulated with AVR brushles, screen protected, drip proof , insulation class-H, IP -23, voltage regulation grade - VG 3 self ventilated and conforming to BS: 5000 / IS: 4722 suitable for engine as mentioned here-in before, conformig to IS: 13364(part-1) Make: stampford/crompton/kirloskar (d) Acoustic Enclosure:- M & L for acoustic enclosure for the above 125 KVA DG set to reduce noise level to 75 dB measured at 1.0 meter distance for audible frequencies as per guide of Central Pollution Control Board with suitabl size manufacturer's specification and comprising of following from authorised GOEMs of Gen Set manufacturer's specified :- (i) Sound insulation : 100mm thick Rock wool (Density 64 Kg/Cum). (ii) Outer body : 1.6mm thick CRCA (iii) Door : 1.6mm thick CRCA (iv) Base frame : ISMC 300 (v) Inside illumination : 1 No.- 1 x 18 watt LED fitting of make Phillips/ Bajaj/ Crompton. (e) AMF Control panel:- Factory fabricated cubicle type, free standing, fixed on angle iron frame made out of 50x50x6 mm, Outdoor type, IP-52, AMF control panel, provided with removable rear panels & hinged front panel for easy accessibility, fabricated out of not less than 2.00 mm thick CRCA sheet including two coats of powder coated paint over a coat of red oxide primer etc and comprising of following:

(f) AMF control circuit with 4 pole MCCB 200 Amps - 2 nos, with ultimate breaking capacity Icu-36 KA at 415 volts and microprocessor release conforming to IEC 60947 Part-I with breaking capacity Ics=Icu at 415 volts , thermal overload setting 70% to 100%, short circuit setting 5 to 10 times-02 Nos. for main supply & DG set supply with HRC back up fuse complete with all DC control relays/ Line voltage monitor (LVM) as per OEM specifications incorporating motorised stored energy operating Engine start, stop, three attempt starting facility and failure to start etc. (g) Digital load manager : Three phase 4 wire indicating V,I,PF, KVA, KW, F of Enercon make with serial communication port model No.EM6400 with class 1.0 accuracy meter or equivalent make suitable rating of CT per phase- one No. (i) Indication lamp R, Y, B with 3 Nos. of HRC fuses-10 sets. (ii) Bottom gland plate for incoming and outgoing cables. (iii) Circuit diagram plate.

AIR CONDITIONING ( CENTRAL)

Design, Supply, install, testing and commissioning of 36 TR running capacity chilled water type central aircondtioning system of not less than 35 TR cooling capacity consisting of 2 x 35 TR scroll chillers (1W+1 S/By) for the Rampage Missile building being constructed under this project tender and consisting of minimum of following sub sytems and plants, machines, motors, pumps, AHUs, pipes, valves, ductings, cable, controllers, instrumentations, metering, logic controls, control panels, equipments and fittings etc all specified and as required. The air conditioning is required for all the rooms/halls/sheds under construction in the project (except toilets and bathrooms) as per the architectural plans, elevation and sections drgs of the building to maintain the desired inside weather conditions of Temperature and Humidity in accordance with the user datasheet given in the tender and as mentioned herein after including balancing, performance and energy optimization techniques and testing commissioning all complete:-

(a ) WATER-COOLED SCROLL TYPE CHILLER UNIT· 2 Nos (1W + 1S) Supply, installation, testing and commissioning of factory designed, pre-fabricated and floor-mounted ISEER 3 star rated inverter scroll type water-cooled chiller machine of nominal capacity 35 TR, complete with scroll compressors having single refrigerant circuits and automatic stepless capacity control, water-cooled S/T type condenser, ASME stamped S/T horizontal evaporator with carbon steel shell and seamless copper tubes with elastomeric insulation, squirrel cage induction motors of appropriate rating with dass 'B' insulation, along with necessary drive arrangement, lubrication system as per manufacturer's design required for smooth and trouble-free operation of the chiller package, common base-frame, interconnected copper refrigerant piping along with elastomeric insulation, fittings, valves, expansion valves and accessories to interconnect compressor, condenser, chiller and expansion valve, microprocessor based control panel comprising of controls including sensors and equipped with a keyboard, LCD touchscreen access input system, protection and monitoring devices to perform control functions, wiring, vibration isolators, gauge panel, automatic safety controls, flow switch at evaporator and condenser connection ends and ozone friendly, CFC-HCFC free refrigerant complete all as specified and directed by the engineer-in-charge. Make: Trane, York, Carrier, Blue star, Voltas, Hitachi The chiller shall conform to the following requirements/ specifications: [i] Chilled water inlet/outlet temperature: 12/7 degree celcius [ii] Evaporator fouling factor: 0.00010 0Fft2 hr/Btu [iii] Evaporator side pressure drop: 5 m of H20 (maximum) [iv] Condenser water inlet/outet temperature: 32/36 deg celcius [v] Condenser fouling factor: 0.00025 0Fft2 hr/Btu [vi] Condenser side pressure drop: 6 m of H20 (maximum) [vii] Minimum COP@ 100% load: 6.0 [viii] Minimum IPLV : 8

[x] Refrigerant (Ozone friendly type): R 134a/R407C/R41 Oa (xi] Test standard: ARI 550 / 590 NOTES: (i] The quoted rate shall be inclusive of Victaulic coupling and system integrator capable of giving industry standard (Modbus/BACnet) output to BMS for critical parameters. [ii] BMS capable Controls with touch screen backlit display providing user-friendly graphical and digital dispaly.Mapping shall be required for all critical points displyed on the chiller control panel. The chiller shall be BMS compatible and shall have RS485/ RS232 serial communication protocol. [iii] As per details mentioned herein after, to automate the start and stop of chillers and motor pumps with continuously monitoring of the set temperature and humidity conditions. [iv] The unit shall be suitable for 3- Phase, 415 V ± 10%, 50 Hz AC electric supply, with a built-in microprocessor based control panel. (v] lnitial / first charge of refrigerant gas & lubrication oil shall be deemed included in the quoted rate. [vi] Necessary civil work viz. foundation for placement Of Chillers, Vibration dampers and pads etc. Shall be deemed included in the scope of work.

(b) CHILLED WATER CIRCULATION PUMP- 2 Nos (1W + 1S) Supply, installation, testing and commissioning of Monoblock, self-priming, single-stage centrifugal pump, capable of 95 USGPM discharge at 16 MWC head, having cast iron casing, enclosed type dynamically balanced cast iron impeller, carbon steel pump shaft, gland packed sealing, deep groove ball bearings, etc. with TEFC squirrel cage induction motor having class 'B' insulation, IE3 efficiency, conforming to IS 12615: 2018 and suitable for operation on 3-Ph, 415 V± 10%, 50 Hz AC supply, base plate, mounting channel frame, accessories and fittings, viz. pressure gauges, thermometers, drains, coupling, coupling guard, vibration isolation arrangement by means of spring I rubber type mounting duly insulated with FM approved highly- flexible, closed· cell thermal insulation of elastomeric foam based on synthetic rubber (NBR) of appropriate thickness laminated with 12 micron aluminium foil facing with reinforced glass scrim along with adhesives and other necessary accessories complete all as specified and directed by the engineer-in-charge. Make: Kirloskar or Crompton, Mahindra, KSB NOTES: Necessary civil work viz. foundation for placement of pump and accessories shall be covered in the scope of work.

(c ) INDUCED DRAUGHT COUNTERFLOW TYPE FRP COOLING TOWER- 2 Nos (1 W+1S) Supply, installation, testing and commissioning of rectangular shape, vertical, induced draught counterflow type FRP cooling tower of 45 TR size with uniform water distribution and optimal heat transfer, having tough fiberglass reinforced plastic (FRP) casing of sufficient structural strength to withstand vibrations and wind velocity up to 60 mls, FRP basin, rigid honeycomb type PVC fill of suitable thickness, SS sprinklers and nonclogging sprinkler pipes, FRP drift eliminator, energy efficient induced draught axial type fans with factory set and dynamically balanced blades pitch, IE3 TEFC squirrel cage induction motor, suitable for operation on 3- Ph, 415 V, 50 Hz AC supply with IP 65 protection for enclosure, conforming to IS 12615: 2018, inlet, outlet, drain and over-flow nozzle connections, etc. complete with accessories along with suitable foundation as per manufacturer's recommendations as specified and directed by the engineer-in-charge. Make: Advance, Delta, Artech NOTES: ( i) Necessary civil work viz. foundation, supporting structure, etc. for placement of cooling tower shall be deemed to be included in quoted rate.

(d ) CONDENSER WATER PUMP· 2 Nos (1W + 1S) Supply, installation, testing and commissioning of Monoblock, self-priming, single-stage centrifugal pump, capable of 116 GPM discharge at 14 MWC head, having cast iron casing, enclosed type dynamically balanced cast iron impeller, carbon steel pump shaft, gland packed sealing, deep groove bail bearings, etc. with TEFC squirrel cage induction motor having class 'B' insulation, IE3 efficiency, conforming to IS 12615: 2018 and suitable for operation on 3-Ph, 415 V± 10%, 50 Hz AC supply, base plate, mounting channel frame, accessories and fittings, viz. pressure gauges, thermometers, drains, coupling, coupling guard, vibration isolation arrangement by means of spring / rubber type mounting complete ail as specified and directed by the engineerin-charge. Make: Kirloskar or Crompton, Mahindra, KSB NOTES: (i) Necessary civil work viz. foundation for placement of pump and accessories shall be covered in the scope of work.

(e ) HOT WATER WATER PUMP· 2 Nos (1W + 1S) Supply, installation, testing and commissioning of Monoblock, self-priming, single-stage centrifugal pump, capable of 50 GPM discharge at 16 MWC head, having cast iron casing, enclosed type dynamically balanced cast iron impeller, carbon steel pump shaft, gland packed sealing, deep groove ball bearings, etc. with TEFC squirrel cage induction motor having class 'B' insulation, IE3 efficiency, conforming to IS 12615: 2018 and suitable for operation on 3-Ph, 415 V±10%, 50 Hz AC supply, base plate, mounting channel frame, accessories and fittings, viz. pressure gauges, thermometers, drains, coupling, coupling guard, vibration isolation arrangement by means of spring I rubber type mounting complete ail as specified and directed by the engineerin-charge. Make: Kirloskar or Crompton, Mahindra, KSB NOTES: ( i) Necessary civil work viz. foundation for placement of pump and accessories shall be covered in the scope of work.

(f) STAINLESS STEEL EXPANSION TANK S & F SS- 304 closed expansion tank with pressure rating to suit the system pressure and sized adequately to compensate for water expansion due to operating temperature variations, conforming to IS: 2825- 1969 for 'nonfired pressure vessels' complete with inter-connection piping, non-return valve, safety relief valve and pressure gauge, insulated with 50 mm thick elastomeric insulation and cladded with 26 gauge aluminium complete with accessories as specified and directed by the engineer-in-charge. 1 00 litre (for chilled water circuit) (g) HDPE MAKE-UP WATER TANK S & F multi-layered HDPE make-up water tank of 10000 litre (2 x 5000 lit) capacity made up of 100% virgin material, having 100% UV stabilized white outer layer, threaded lid, extra insert lid for protection against algae formation complete with inter-connection piping and non-return valve etc. complete ali as specified and directed bv the enaineer-in-charae. (h) POWER CABLES M & L for lSI marked 1.1 kV grade aluminium conductor, XLPE insulated armoured cables, conforming to IS:7098 (Part 1 )- 1988 having stranded aluminium compact shaped conductor as per Cl. 2, IS: 8130- 1984, PVC inner sheath, single armouring of galvanized steel strip/wire and PVC Type ST- 2 outer sheath conforming to IS:5831-1984, including termination complete as specified and directed by the engineer-in-charge. Make: RR Kabel, Polycab, Havens 4 core, 16 mm2 [for AHU]

(g ) M & L for 1.1 kV grade copper conductor, XLPE insulated armoured cable conforming to IS 7098 (Part 1): 1988, having stranded copper compact shaped conductors as per Ct. 2 of IS 8130: 1984. PVC inner sheath, single armouring of galvanised steel strip/wire and PVC Type ST-2 outer sheath conforming to IS 5831: 1984, including necessary clamping/ dressing with cable ties and termination complete all as specified and directed by engineer-in-charge. Make: RR Kabel, Polycab, Havells 3.5 core, 25 mm2 [for chillers & hot water generator] 3 core, 6 mm2 [for cooling tower] 3 core, 6 mm2 [for pump starter to motor terminals except Hot Water Pump] 3 core, 4 mm2 [for Hot Water Pump starter to motor terminals)

Outgoing: [i) 100 A, 415 V, lcs = 100% lcu= 36 kA, 50 Hz FP MCCB, conforming to IEC 60947-2, having microprocessor based trip unit, adjustable overload setting (0.7- 1 X In), adjustable short-circuit setting (5- 10 X lr), adjustable neutral protection (N, N/2, OFF), front indication LCDs (Ready, Overload and pre-alarm & Overload), etc.- 02 Nos. lfor Chiller! [ii] 63 A, 415 V,lcs =leu= 36 kA, conforming to IEC 60947- 2,50 Hz, FP MCCB with adjustable thermal settings (0.70-1 X In) & fixed magnetic settings with compression lug connectors and thermal magnetic trip unit (TMD)- 01 Nos. [for AHU) [iii] 40 A, 415 V, lcs = lcu = 36 kA, conforming to IEC 60947- 2, 50 Hz, FP MCCB with adjustable thermal settings & fixed magnetic settings with compression lug connectors and thermal magnetic trip unit (TMD)- 02 Nos. [for Cooling Tower]

(j ) EARTHING M & L for earthing complete with copper earth plate electrode of 60 em x 60 em x 3.15 mm size, buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level, connected to copper strip of size 20 mm x 3 mm as earth lead, by means of bolts, nuts, check nuts and washers of galvanised iron or steel, galvanized iron pipe of 40 mm diameter, connected to · earthing test point, all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion and also including excavation, earthwork in any type of strata, PCC earth pit of dimensions 550 mm X 550 mm (outer) and 300 mm X 300 mm (inner) and 250 mm deep, with a 10 mm thick Cl cover, hinged to Cl frame on ground level, Gl watering pipe, funnel, etc. complete as specified and directed by the engineer-incharge. (for chiller)- 2 Nos

M & L for earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 20 mm X 3 mm copper strip complete all as specified and directed by the engineer-in-charge- as required (p) WATER PIPING & VALVES NOTES: Sizes and Quantities under this shall be as per standard design requirements to achieve optimum performance parametrs in accordance with Ashrae handbook and standard hydraulics & air conditioning practices and per approved design and drgs

(i) MS ERW CLASS. C PIPE Supply, laying/fixing, testing and commissioning of MS ERW Class -C pipes for condenser/chilled water/hot water, drain, instrumentation including necessary fittings viz. bends, tees, reducers, flanges, air purge valves, drain valves, structural support, necessary clamps, vibration isolators, etc. including painting and supporting / fixing the pipe in excavated trenches or on floor/ wall / ceiling with clamps, hangers, angles, channels (using anchor fasteners) with necessary accessories complete all as specified and directed by the engineer-in-charge. Make: Tata, Jindal, Surya [ij Chilled water and hot water piping, valves, strainers shall be duly & thermally insulated with FM approved highly- flexible, closed-cell thermal insulation of elastomeric foam based on synthetic rubber (NBR) of appropriate thickness laminated with 12 micron aluminium foil facing with reinforced glass scrim along with adhesives and other necessary accessories, insulation of make Armacell, K-Fiex, Aeroflex (iij The pipe size 150 mm NB & below shall be MS 'C' class as per IS 1239 (Part- 1 ): 2004 & IS 1239 (Part- 2): 2011. (iiij The pipe size above 150 mm NB shall be welded black steel pipe heavy class as per IS 3589: 2001 . (iv] Minimum thickness of MS sheet for pipe size above 150 mm NB and up to 350 mm NB shall be 6.35 mm

(ii) Y- STRAINERS Supply, installation, testing and commissioning of cast steel bolted cover Y -type strainers with CCS body conforming to ASTM A- 216 Gr. WCB, AISI 304 screen with 1.2 mm diameter perforation, 40 kg/cm2 body test pressure & 20 kg/cm2 maximum working pressure and standard flange end conforming to BS 10 Table F/ Class-150 with necessary accessories complete all as specified and directed by the engineer-in-charg Make: Advance, Sant, Hindustan (iii) BUTIERFL Y VALVES & BALL VALVES Supply, installation, testing and commissioning of wafer type PN 1.6 rated short pattern Cl butterfly valves having Gr. FG-200 Cl body conforming to IS 210: 2009, seat having EPDM rubber lining, CF 8 stainless steel disc, AISI- 410 stainless steel stem, 2.4 MPa body test pressure & 1.6 MPa seat test pressure and standard flange end conforming to BS 10 Table DIE & ANSI B 16.1 Cl- 125 with necessary accessories complete all as specified and directed by the engineer-in-charge.- quantities as required- Ball valves for sizes 50 mm and (iv) NON-RETURN VALVES :Supply, installation, testing and commissioning of wafer type PN 1.6 rated swing check type multidoor reflux valve (NRV), designed & tested as per IS 5312 (Part- 2): 1986, suitable to handle clear water having turbidity up to 5000 PPM, having Cl body, door and diaphram, leaded tin bronze seat rings and flange drilling standard end connection, etc. with other necessary accessories complete all as specified and directed by the engineer-incharge Make: Advance, Sant, Hindustan

(q ) MANUAL BALANCING VALVES Supply, installation, testing and commissioning of precise balancing, double regulation type cast iron balancing valve chilled water/condenser water and hot water systems having FG 200 cast iron body conforming to IS 210: 2009, copper alloy trim, stainless steel2 Cr. 13 stem, 2.4 MPa body test pressure & 1.6 MPa maximum working pressure and standard flange ends with necessary accessories complete all as specified and directed by the enaineer-in-charae. Note: Manual balancing valves shall be calibrated and commissioned using portable flow meter and/or other metering instruments to arrive at the prcise setting of the required flow rates. Make: Danfoss/Honeywell

(r) 3-WAY TEMPERATURE CONTROL VALVE Supply, installation, testing and commissioning of electronic, self-balancing dynamic balancing valve for chilled wale and hot water systems rated for minimum 25 bar working pressure with integrated 3-way modulating control valve of required size in a single body and actuator capable of accepting up to 10-24 V DC and up to 20 mA electric signal and provide similar transduced feedback output to control system duly insulated with FM approved highly- flexible, closed-cell thermal insulation of elastomeric foam based on synthetic rubber (NBR) of appropriate thickness laminated with 12 micron aluminium foil facing with reinforced glass scrim along with adhesives and other necessary accessories complete all as specified and directed by the engineer-in charge 02 nos Make: Honeywell, Danfoss, Advance for 3-Way Modulating Control valve & Armacell, K-Fiex, Aeroflex for insulation NOTES: [il Maximum close off pressure shall not be less than 6 bar for up to 50 mm valves. [ii] Maximum close off pressure shall not be less than 7 bar for 65 mm & above.

(s ) AUTO AIR-VENT Supply, installation, testing and commissioning of automatic air-vent valve with 20 mm end connections, brass OT 58 body and cover, polyacetal lever, high density expanded polyethylene float, EPDM rubber plug, stainless steel spring, polyamide cap etc. suitable for maximum operating pressure of 16 bar and maximum operating temperature 115 deg celcius respectively, installed on all high points in the water piping system to automatically remove the trapped air complete all as specified and directed by the engineer-in-charge. - 4 nos Make: Advance, Sant, Hindustan (t) TEMPERATURE GAUGE S & F of 6" dual scale (0 F/0 C), lower mount (radial), bimetal thermometer having 0.5 NPT process connection, Grade A accuracy class as per ASME B40.200, stem diameter 6.35 mm, laminated safety glass window, stainless steel 304 case, steam, process connection & joint, aluminium dial & pointer, IP67 protection, scale range 0- 60 deg celcius complete with accessories, etc.all as specified and directed by the engineer-in-charge. - quanity as per standard requirement Make: General, WIKA, TSI (u) PRESSURE GAUGE S & F of 4' bourdon tube pressure gauge conforming to EN 837-1 , having copper alloy process connection & pressure element, plastic black pointer & case, plastic crystal-clear window, snap-fitted in case, accuracy class 2.5, scale range 0- 25 bar complete with accessories, etc. as specified and directed by the engineer-in-charge. - quantity as per standard reauirement Make: General, WIKA, TSI

AIR DISTRIBUTION (v) DOUBLE SKIN AIR HANDLING UNIT Supply, installation, testing and commissioning of double-skin type horizontal, floor-mounted, top/ side discharge air handling unit capable of delivering 10000 CFM air at designed value of ESP W.G. static pressure and having thermal break profile complete with air-tight casing using gaskets and self-adhesive tapes and 0.6 mm thick pre-coated outer skin and 0.6 mm thick Gl inner skin, 45±2 mm thick double skin panel with pressure injected CFC & HCFC free PUF having 'k' value of 0.02 W/0 C/m & density 40 kg/m3 , AMCA certified energy efficient plug fans with backward curved impellers for high static pressure mounted on aluminium extruded siderail base frame, EU4 pre-filter and EU7 fine filter (shall be mounted on a common frame), combination of 6/8 rows deep chilled water coils with anti-corrosion aluminium fins, suitable high efficiency (IE3) TEFC flameproof squirrel cage induction motor, electric step heater, PVC/nylon hinges & handles, view port and marine lamp, limit switch, SS-304 drain pan, vibration isolators/rubber pads (minimum 1" thick) inspection windows / doors, mixing box and supply / return / fresh air openings fitted with aluminium volume control dampers complete all as specified and directed by the engineer-in-charge- 1 No Make: Trane, Carrier, Daikin, Flak group The AHU shall comprise of the following: [a] Suitable SISW backward curved plug fan, dynamically balanced, with AMCA certified blower [b) Foot mounted (83 construction) 3-Phase squirrel cage induction motor 415 V ± 10%, 50 Hz ± 5 %, combined variation ±10%, insulation class F, (for Blower of AHU) of 15 kW capacity, 35000 CFM with temperature rise limited to class 8, degree of protection IP 55, duty 51, ambient temperature 45 deg celcius, conforming to IS 12615: 2011, IS/IEC60079-1: 2007, IS3682: 1966 gas group II A, II B [c) Flexible connection made with airtight ASTM E84 (Class I) polyester fire retardant cloth riveted on periphery of cloth with extruded aluminium 'L' angle flannge as per fan size at discharge duct/plenum

[d) Washable type of 'EU4' filter (pre-filter, efficiency 90% down to 10 micron) and 'EU7' filters (Micro Vee filters, efficiency 99% down to 3 micron) (e) 6/8 rows deep chilled water cooling coil section with 0.15 mm thick aluminium fins and 0.36 mm diameter copper tubes tested on 21 kg/cni, with 55 sandwiched drain tray, etc. (a ) 350 mm service section between eliminator and heater is required) [ij Condensate drain pan fabricated from 18 gauge SS 304, powder coated and insulated with elastomenc insulation of suitable thickness (g] 214 row deep heating coil section with aluminium fins and copper tube tested on 21 kg/sqcm with SS sandwiched drain tray, etc. [h) AHU panel made out of 2.00 mm thick mild steel CRCA sheet, duly powder coated in compartmentalised construction with incomer and outgoing feeders for AHU motor, 3-way valve actuator motor, fire damper actuator motor, etc. complete with required variable frequency drive (VFD), relays, timers, contactors, PT, push buttons. switches. internal wirinG. etc. (i] AHU chilled and hot water flow system will be automated with Thermostat and humidistat of central aircondltioning grade & features to be integrated and calibrated in conjuction with the 3-way motorized control valve duly supplied, installed and connected and controlling the flow of water into the Chilled Water and Hot water coils based on adjustable setting requirements of temperature and humidity. Thermostat/Humidista shall be of Honeywell /Danfoss make. G) Three feedback PID controller having capability to simultaneously accept 3 feedback signals from temperature sensors or pressure sensors for process optimization and accordingly control the speed of the pumps.

NOTES: [k) Necessary civil work viz. foundation for placement of AHU, mounting of panel, construction of opening(s) for fresh/exhaust air etc. shall be covered in the scope of work

FIRE DAMPER Supply, installation, testing and commissioning of 16 gauge Gl fire damper, at least of 120 minutes fire-rating, spring activated on melting of fusible link having melting point 67.13" C complete with smoke detector /thermistor, fusible link etc. and actuator as required for operation, located in the SA/RA ducts, at all fire rated crossovers (shafts, walls, etc.). along with control panel (located in such a way that the reset can easily be done), interlocked with the building management system for the fire detection or HVAC to trip/ close in the event of fire/smoke in the respective zone and tested as per ULL- 555 and certified by CBRI complete all as specified and directed bv engineer-in-charge. Make: Ruskin Titus, Trox, Rola Star, Zeco The fire dampers shall meet the following criteria: [a) Bare fire dampers with 400 mm sleeve (b) Control panel actuator, including electrical spring type actuator, remote indication of the fire damper position. [c) interconnection wire for the fire detection & alarm system with the AHU and the smoke dampers (d) Sealing any openings around the sleeve of the fire dampers with approved fire sealant as per the specification & recommendations of the manufacturer. Motorized, spring return type, combination fire and smoke damper Control panel actuator, including electrical spring type actuator, remote indication of the fire damper position. - Qty as per approved design

(x ) GALVANIZED STEEL SHEET (GSS) DUCTING : Supply, installation, balancing and commissioning of factory fabricated galvanized steel sheet metal (G.S.S.) round I rectangular dueling of following sheet thickness having zinc coating of 120 g/m2 total on both sides and complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, volume control dampers, hangers, supports, etc. as per approved drawings and conforming to the latest edition of IS 655: 2006 & HVAC Duct Construction Standards - Metal and Flexible of SMACNA along with required scaffolding work to install the ducts at site complete all as specified and directed by engineer-in-charge.- Qty as reqd as per approved design and drgs Make: Ruskin Titus, Trox, Rola Star 26/24/22/20/18 Gauges per approved duct design with (MS angle flanges) NOTE: The supply and return ducts shall be installed across the VIFT (Vertical Inverse Face Traverse) in an inclined slope. The same shall be supported with robust iron frame structure and the insulation over the dueling in the outdoor shall be jacketed with aluminium sheet metal of 0.5 mm thickness duly covering and punched together with sufficient overlaps all as required and as specified .. (y) AIR TERMINALS S & F of supply/ return / exhaust air diffusers / grilles /louvers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core complete all as specified and directed by the engineer-in-charge. - Qty and size as per approved design. Make: Ruskin Titus, Zeco, Rola Star

(z )THERMAL INSULATION S & F of FM approved black flexible closed-cell elastomeric thermal insulation made of elastomeric foam based on synthetic rubber (NBR / PVC) with self pre-covered self-adhering, UV treated glass cloth of thickness 7 mm /200 GSM, tested for maximum service temperature 100 deg celcius as per ASTM C411 & minimum service temperature ·50 deg celcius as per ASTM C534, thermal conductivity ≤: 0.037 W/mK at mean temperature 0m = 24 deg celcius as per ASTM C518/ C177, ASTM C335, water absorption by volume :5:0.2% as per ASTM C1763, fire spread index (FSI) & smoke development index (SDI) 25/50 as per ASTM E84, flammability HB, V-0 as per UL 94, fungi resistance as per ASTM G21, mould growth resistance as per ASTM E2180-18/ UL 181 and ozone resistance as per ASTM D 1149-18 along with adhesives and other necessary accessories complete all as specified and directed by the engineer-in-charge. - Qty as per approved design Make: Armacell, K-Flex, Aeroflex 13 mm/19 mm thick thermal insulation (aa) S & F of FM approved fibre-free, super-silent, microbe resistant, easy to apply 10 mm thick acoustic duct lining insulation of open cell elastomeric foam based on synthetic rubber tested for acoustic performance as per ENISO 354, EN ISO 11654: 1997 & ASTM C 423, service temperature range -20-85 deg celcius as per EN 14706 & EN 14304, thermal conductivity A ≤0.047 W/mK at mean temperature 0 m = 20 deg celcius as per EN 12667, Class 1 surface spread of flame as per BS 476 7: 1997, flammability HB, V-0 as per UL- 94, anti-microbial behaviour (no fungal growth visible with the naked eye & no bacterial growth) as per EN ISO 846, air erosion resistance (no erosion, cracking or delamination at air velocity of 10000 FPM) as per ASTM C 1071- 05, density 140- 180 kg/m3 along with adhesives and other necessary accessories complete all as specified and directed by engineer-in-charge.- Qty as reqd

(ab) Blank (ac) Automatic Condenser Cleaning System Supply, Installation, Testing & Commissioning of Automatic Brush Ball Online tube cleaning system equipped with computer control panel, ball re-circulation device, ball entrapment module, ball diverter module, ball injection module requiring cleaning balls for cleaning condenser tube system for each chiller. The cleaning devices shall comprise different types of elastomeric balls of various sizes and different specific gravities to effect the tube cleaning process at predetermined time while the condenser is online. The automatic tube cleaning system shall be equipped with a master programmable logic controller with user definable features to adjust cleaning cycle frequency, injection timing, retrieval timing and rest cycle timing to suit operational parameters of condenser, ball injection module, ball retrieval module and related piping configuration comprising the master mechanical components control system to be installed for each chiller condenser. The automatic tube cleaning system shall utilize cleaning balls with spikes configured to reach and clean grooves of enhanced tubes. The automatic tube cleaning system shall utilize cleaning balls with diametre smaller than the diametre of the tubes. The automatic tube cleaning system shall utilize eccentrically weighled cleaning balls to enhance dynamic zig-zag impact cleaning mechanism capable of cleaning grooves of enhanced tubes. An Independent System to be provided for each Chiller. Quantity - 2 NOS (ad) AIR SEPARATOR: Supply, installation, testing & commissioning of Centrifugal Air Separator with 16" (PN10) (400mm) inlet outlet (tangential & flanged) (With Matching Flanges) (Non ASME) with Auto Super Air Vent o/."size. DN20 (PN10) with Ball Valve. insulation with nitrile rubber as per the specification.

Services for Manning & Operation of AC Plant

Outsourcing of services for manning and operation of chilled water type central AC Plant round the clock in Three shifts (0600 hrs to 1400 Hrs, 1400 Hrs to 2200 hrs and 2200 hrs to 0600 hrs ) for all the seven days in a week including operation of connected items such as main switch, starter, change over switch, MCCB, Voltmeter, Ammeter, panel board, Air handling unit, cooling tower, condenser water pump, valve system, controlling condenser, refrigerant line, adjusting expansion valve, refrigerant valve, bypass valve, daily checking leakage, checking noise, controlling temperature, humidity, water level in cooling tower, daily maintenance of plant, cleaning etc all as specified and directed by Engr-in-Charge.

1 st cycle after certified date of completion of work

2 nd cycle after certified date of completion of work

3 rd cycle after certified date of completion of work

4 th cycle after certified date of completion of work

5 th cycle after certified date of completion of work

6 th cycle after certified date of completion of work

COMPREHENSIVE MAINTENANCE OF AC PLANT

Comprehensive maintenance comprising of routine, preventive & breakdown maintenance of central air conditioning plant of capacity 22 TR installed running capacity with 3x 11 TR. Package type air cooling air conditioning unit ( 2 running & 1 standby ) installed comprising of all devices and accessories through out 12 months on all days including sundays & holidays for a period of 03 years after expiry of defects liability period (i.e. 24 months after completion of all Phase II tests) all as specified and directed and as shown below.

1st year after expiry of defect liability period.

2 nd year after expiry of defect liability period.

3 rd year after expiry of defect liability period.

NOTES FOR ITEM NOS 26 & 27 :- (a) The contractor shall be responsible for periodical/routine maintenance, as per maintenance schedule recommended by manufactur/OEM, including renewal / replacement of parts, fittings / fixtures filling of refrigerant gas etc required for smooth functioning of the plant as per manufacturers instructions.the cost of all parts/componant/Gas required for replacement are considered inclusive in quoted rate (b) The Contractor shall Employ Refrigeration mechanic having minimum ITI qualification from Govt Recognised institute with adequate knowledge & minimum 5 years experience in maint/operation of AC plants. The operator must competent to carry out the minor maint all as directed. (c) Contractor shall pay the wages to the employees through e-payment i.e Adhaar linked bank accounts (credit to their bank account). Engineer-in-charge shall ensure that e-payment made to employees and their wages shall not be less than minimum wages fixed by state Govt or Central Govt whichever is more. Monthly e-banking statement shall be furnished by the contractor to the Engr-in-charge and the same shall be kept in record duly verified.

(d) It is the responsibility of contractor to deposit the employees provident fund (EPF) to the concerned authority as per the prevailng scales as laid down by Ministry of labour for all operator/helper (as appliable) and necessary proof to this regard shall be submitted to the Engineer-in-charge for verification & record. The quoted rates shall be deemed to be included of above provisions. In case contractor fails to produce the proof of EPF, the same shall be recovered from his dues as per the prevailing scale plus 15 percent. (e) The contractor shall maintain all the registers under various labour law rules, 2017 and shall be produced to the Engineer-in-Charge as well as officers detailed by central labour department. (f) Each shift duration shall be 8 hours & duty timing will be decided by Engr-in-Charge.(g) The unit rate quoted shall deemed to be included for cost of labour for daily routine maintenance for trouble free functioning of installation. (h) In case of any abnormal noise/ complaint the plant should be put off and same should be brought to the notice of Engr-in-charge. (i) The operator employed by the contractor shall be capable of carrying out minor repair/ maintenance & should have well experience in AC plants as applicable. (j) The quoted rate is deemed to be inclusive of cotton waste, cleaning material etc & Contractor will ensure general area cleanliness and upkeep of the installation on daily basis. (k) The quoted rate is deemed to be inclusive of tools & testing instruments required for operation & maintenance of AC plants. (l) The rate quoted shall deemed to be inclusive of safety gear & required tools for minor maintenance. In case of failure to provide tools kit & safety kit (spanner sets, hand gloves), a penalty of Rs 3000/- will be recovered and levied

(m) The Contractor shall not employ same tradesman continuously for more than 11 months during the Contract period. (n) The contractor shall provide 02 uniforms to each operator and design of uniform shall be got approved. In case of failure, a penalty of Rs 2000/- per uniform will be levied and recovered from their dues. (o) In case of failure due to absence of operative staff, the contractor shall be liable to pay compensation at twice the cost of a day’s Manning & Operation derived from pro rate of Sch ‘A’ quoted rates. (p) The Contractor shall maintain proper records of all kinds of daily, weekly, monthly, quarterly, half yearly and yearly or whatsoever maintenance is carried out during contract period in a binded book / register and shall obtain the signature of Engineer-in-Charge every fortnightly. (q) The contractor shall provide board at proper location near each installations duly writting the name of operators and Mobile Numbers shifwise. (r ) In case of non function of AC Plant panel recovery @ 3000 per day shall be effected 24 hrs after the defect is noticed or notified either in writing or through a social media message by GE or his rep. (s) Any defect in to a motor , Pumps, compressure ,Control Panel ,AHU, Refrigarent Gas , Cooling Tower shall be considered as outstanding defect & Panel charge will be applicable as above in Note (u ) In case of non function of central type AC plant, penal recovery @ Rs 3000 per day shall be effected 24 Hrs after the defect is notified either in writing or through a electronic media message by GE or his Rep.

S.N. Constructions

M/s. R.S. LAWANDE