C/o Panchkarma and Kasharutra Building on Ist floor of Ayurvedic Hospital at Nalagarh Distt. Solan HP

Amount

Providing form work with steel plates 3.15 (Three point One Five ) millmetress thick welded with angle iron in frame 30x30x5 (Thirty in to Thirty in to Five ) millmetress, so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies in all heights of propping and centering below supporting floor to ceiling and removal of the same in-situ-reinforced concrete and plain concrete work as per HP.PWD specification 1990 volume-I, including carriage of all labour equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Foundation footing and basis of columns, etc. and mass concrete.

Columns, Pillars, Piers, Abutments, Posts and Struts

Suspended floors, roofs, landings, balconies and access platform

Stairs, (excluding landings) except spiral staircases

Edges of slabs and breaks in floors and walls under 20 cm wide.

Providing and laying in position cement concrete 1:1.5:3 [ One cement: One and half sand: Three graded crushed hard stone aggregate 20 (Twenty) millmetress nominal size] machine batched and machine mixed design mix M-25 ( Twenty five) grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing with 1:2:4 [ One cement: two sand: four graded crushed hard stone aggregate 40 (Forty) millmetress nominal size] including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges

10 cm( Ten centimeters) thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm ( twenty five only)thick mud mortar mixed with bhusa @ 35 kg ( Thirty five kilogram) per cubic meter of earth and gobri leaping with mix 1:1 (one clay : one cow dung) and covered with flat tile bricks, grouted with cement mortar 1:3 (one cement : three fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat:.With common burnt clay F.P.S.(non modular) brick tile of class designation 10 (Ten)including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level, Mild steel and Medium Tensile steel barsincluding carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4 (one cement : four coarse sand) including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Half brick masonry with common burnt clay F.P.S. (modular) bricks of class designation 12.5 ( Twelve point five) in superstructure above plinth level up to floor V level in Cement mortar 1:4 (one cement :four coarse sand) including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built upnstandard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in charge. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portion, Powder coated aluminium (minimum thickness of powder coating 50 ( Fifty) micron) including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm ( Twelve millimeters)thick Pre-laminated particle board with decorative lamination on both sides flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer- in-charge.

Providing and fixing glazing in aluminium door, window,ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm( Twelve ponit five kilogram per square meter) including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing 18 mm ( Eighteen millimeters) thick, 150 mm ( One hundred fifty millimeters) wide pelmet of flat pressed 3 layer or graded wood particle board medium density grade I, IS : 3087 marked, including top cover of 6 mm commercial ply wood conforming to IS: 303 BWR grade, nickel plated M.S. pipe 20 mm dia ( Twenty millimeters diameters) ( heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm M.S. flat 10 cm ( Ten centimeters) long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm ( Hundred millimeters into forty millimeters i nto forty millimeters) on both inner side of pelmet and rawl plugs 75 mm ( Seventy five millimeters) long etc. all complete.

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15 ( Fifteen) ) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm ( two hundred millimeters) centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge. (Only weight of grill to be measured for payment)including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing wire gauge laminated veneer lumber shutters conforming to IS : 14616, and as per TADS 15 :2001 (Part B) using galvanised wire gauge with average width of aperture 1.4 mm ( One point four millimeters) in both directionswith wire of dia 0.63 ( Diameter zero pint sixty three millimeters) mm as per IS :1568, for doors,windows and clerestory windows fixing with butt hinges of required size with necessary screws, as per directions of Engineer-in-charge: (Note:- Butt hinges and necessary screws shall be paid separately)

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

300 X 16 mm (three hundred in to sixteen millmetres)

250 X 16 mm (two hundred fifty in to sixteen millmetres)

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

250 x10 mm. (two hundred fifty in to ten millmetres)

150x10 mm(one hundred fifty in to ten millmetres)

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

125 mm (one hundred twenty five millmetres)

100 mm(one hundred millmetres)

Providing and fixing ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

125x65x2.12 mm( One hundred twenty five into sixty five into two point twelve millimeters)

75x47x1.70 mm( Seventy five into forty seven into one point seventy millimeters)

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg ( Thirty six kilogram to eighty kilogram) and door width from 701 mm to 1000 mm (Seven hundred one millimeters to one thousand millimeters) ), with double speed adjustment with necessary accessories and screws etc.including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm ( Three hundred by three hundred millmetres)(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar1:4 (one Cement : four Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm (Three point three kilogram per square meters) including pointing the jointswith white cement and matching pigment etc.including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm (Twelve millimeters) thick bed of cement Mortar 1:3 (one cement: three coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm ( Three point three kilogram per square meters) including pointing in white cement mixed with pigment of matching shade complete including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% ( Zero point zero eight percent) and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm ( Three point three kilogram per square meters) including grouting the joints with white cement and matching pigments etc., complete including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.(600X600 mm)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% ( Zero point zero eight percent) and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm ( Three point three kilogram per square meters) including grouting the joints with white cement and matching pigments etc., complete including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.(500X500 mm)

25 mm (Twenty five millimeters) Kota stone slab flooring over 20 mm (Twenty millimeters) (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (one cement : four coarse sand) including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Kota stone slabs 20 mm (Twenty millimeter) thick in risers of steps, skirting, dado and pillars laid on 12 mm (Tweleve millimeter) (average) thick cement mortar 1:3 (one cement: three coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab including rubbing and polishing complete including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing on wall face unplasticised Rigid 110 mm ( One hundred ten millimeters) diameter PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm ( Ten millimeters) gap for thermal expansion, (i) Single socketed pipes including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm ( Ten millimeters) gap for thermal expansion. Bend 87.5° ( Eighty seven degree ) , 110 mm ( One hundred ten millimeters) diameter bend including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing unplasticised 110 mm ( One hundred ten millimeters) diameter PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm (fifty by fifty by fifty millmetres) hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (one cement : four coarse sand) and making good the wall etc. complete including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required in gratings, framed, guards, bars ladders and railing, brackets and similar works including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade over New work (two or more coats) over and including water thinnable priming coat with cement primer including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Finishing walls with textured exterior paint of required shade over new work (Two or more coats applied @ for external plaster are for height upto 3.28 ltr/10 sqm) ( Three point twenty eight liter per ten square meter) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm ( two point twenty kilogram per ten square meters) including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

6 mm ( Six millimeters) cement plaster 1:3 (one cement : three fine sand) finished with a floating coat of neat cement and thick coat of Lime wash on top including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

15 mm ( fifteen millimeters) cement plaster 1:6 (one cement: six fine sand) on the rough side of single or half brick wall of mix including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

12 mm ( Twelve millimeters) cement plaster 1:4 (one cement: four fine sand) of mix on the fair side of single or half brick wall of mix including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Excavation in earth work in drains and channels in all heights & depth in all kinds of soils, including struated soil comprising of pick work, jumper work and blasting work ( both soft & hard rock ) & wedging out of rock,( where blasting is prohibited ) and their interemediate classification of soil including dewatering wherever required, setting out to required lines, grades, side slopes, trimming bottoms and levels as shown on the drawing and as directed by the Engineer-in-Charge at site, according to the HP.PWD., specification of and sorting out useful unuseful materials and stacking the same in all leads and lifts and levelling and disposing of surplus excavated earth in acquired width of road or on approved dumping sites which will be arrange by the contractor at his own level and dumping charges if levied will be born by the contractor through all modes of transportation and used/ removed as direction of the Engineer-in-Charge including head load,animal load or mechanical means along with its levelling fine dressing & all labour,machineries,materials tools equipments and safety measures and incidentals necessary to complete the work by mechanized means & labour ( if any required ).All useful materials, such as stones, shingles, aggregate and slates shall be sorted out and stacked along road side to the maximum possible extent in all leads and lifts through all modes of transportation and used/ removed as per direction of Engineer-in-Charge. Any loss to the public and private properly during the course of execution and dispoal of serviceable and un-serviceable materials shall be the aboulute responsibility of the contractor and shall have to be duly compensated by him in all respects including all incidental charges.

Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer-incharge.

1216 ( one thousand two hundreded sixteen)16 mm ( Sixteen millimeters) OD pipe

2025 ( Two thousands twenty five) 25 mm ( Twenty five millimeters) OD pipe

Providing and fixing 25 mm ( Twenty five millimeters) G.I. pipes complete with G.I. fittings including trenching and refilling etc.for external workThis includes testing of joints complete as per direction of the Engineer- incharge.

Making connection of galvanised steel distribution branch with galvanised mild steel main 20mm to 40mm ( Twenty millimeters to forty millimeters) nominal bore by providing and fixing tee iincludingcutting and threading the pipes complete including carriage of materials within all leads and lifts s directed by Engineer-in- Charge.

Fixing of water meter stop cock including fittings such as mild steel galvanized jam nut, sockets etc. cutting and making long secrews complete as per HP.PWD specification 1990 volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges .

Constructing masonry Chamber 60x60x75 cm ( sixty into sixty into seventy five centimeter) inside, in brick work in cement mortar 1:4 (one cement : four coarse sand) for sluice valve, with C.I. surface box 100mm ( One hundred millimeter) top diameter, 160 mm ( One hundred sixty millimeters) bottom diameter and 180 mm ( One hundred eighty millimeters) deep ( inside) with chained lid and RCC top slab 1:2:4 mix ( one cement: two sand: four graded stone aggregate 20mm ( twenty millimeter)(nominal size), i/c necessary excavation, foundation concrete 1:5:10 (one cement : five sand: ten graded stone aggregate 40 mm ( Forty millimeter) nominal size) and inside plastering with cement mortar 1:3 (One cement : three coarse sand) 12 mm (Twelve millimeters) thick, finished with a floating coat of neat cement complete as per standard design with common burnt clay F.P.S.(non modular) bricks of class designation 7.5 including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges .

Providing and fixing 1216 ( one thousand two hundreded sixteen)16 mm ( Sixteen millimeters) OD pipePolyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges ..

Providing and fixing Sand cast iron S&S as per IS: 3989 trap 100 mm ( Hundred millimeters) inlet and 100 mm ( Hundred millimeters) outletof self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floorsincluding carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges .

Providing and fixing PVC waste and ventlating pipes including filling the joints with approved adhesive complete as per HP.PWD.specification 1990 volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges .

75 mm (Seventy five millimeter)nominal bore

110 mm (One hundred ten millimeter)nominal bore

Providing and fixing PVC door Bends of required degree(any radius)ISI marked with oval access door insertion rubber washer 3 (three) millmetres thick, bolts and nuts complete supreme fittings and accessories complete as per direction of the Engineer-in-Charge and HP.PWD. Specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads and lifts including all incidental charges.

75 mm (Seventy five millimeter)nominal bore

110 mm (One hundred ten millimeter)nominal bore

Providing and fixing PVC plain Bend supreme fittings and accessories complete as per direction of the Engineer-in-Charge and HP.PWD. Specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads and lifts including all incidental charges.

75 mm (Seventy five millimeter)nominal bore

110 mm (One hundred ten millimeter)nominal bore

Providing and fixing PVC single equal branch with oval access door insertion rubber washer 3 (three) millmetress thick, bolts and nuts complete supreme fittings and accessories complete as per direction of the Engineer- in-Charge and HP.PWD. Specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads and lifts including all incidental charges.

75 mm (Seventy five millimeter)nominal bore

110 mm (One hundred ten millimeter)nominal bore

Providing and fixing PVC plain double equal branch complete supreme fittings and accessories complete as per direction of the Engineer-in-Charge and HP.PWD. Specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads and lifts including all incidental charges.

75 mm (Seventy five millimeter)nominal bore

110 mm (One hundred ten millimeter)nominal bore

Providing and fixing PVC collar complete supreme fittings and accessories complete as per direction of the Engineer-in-Charge and HP.PWD. Specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads and lifts including all incidental charges.

75 mm (Seventy five millimeter)nominal bore

110 mm (One hundred ten millimeter)nominal bore

Providing and fixing PVC cowl I.S.I marked including cutting holes in walls and making good the same, as per HP.PWD specification, including carriage of all labour equipment and material to various location through all modes of transportation in all leads ifts and all incidental charges .

75 mm (Seventy five millimeter)nominal bore

110 mm (One hundred ten millimeter)nominal bore

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 ( Ten) litre low level white P.V.C. flushing cistern, W.C. pan with ISI marked white solid plastic seat and lidincluding flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required including carriage of all labour equipment and material to various location through all modes of transportation in all leads ifts and all incidental charges .

Providing and fixing White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require including carriage of all labour equipment and material to various location through all modes of transportation in all leads ifts and all incidental charges .

Providing and fixing 32 mm diameter ( Thirty two millimeters) C.P. brass chain and rubber plug complete for sink or wash basin including carriage of all labour equipment and material to various location through all modes of transportation in all leads ifts and all incidental charges .

Providing and fixing 32 mm diameter ( Thirty two millimeters) G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required including carriage of all labour equipment and material to various location through all modes of transportation in all leads ifts and all incidental charges .

Providing and fixing CP Brass 32 mm diameter ( Thirty two millimeters) size Bottle Trap of approved quality & make and as per the direction of Engineer- in-charge

Providing and fixing 100 mm ( One hundred millimeters) sand cast Iron grating for gully trap including carriage of all labour equipment and material to various location through all modes of transportation in all leads ifts and all incidental charges

Providing and fixing 600 x 450mm (six hundred into four hundred fifty mm) beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete as directed by the Engineer-in- Charge including carriage of materials within all leads and lifts and other incidentals and as per the entire satisfaction of Engineer-in-charge.

Providing and fixing PTMT towel rail 600 mm ( Six hundred millimeters) long towel rail with total length of 645 mm ( Six hundred forty five millimeters), width 78 mm (seventy eight millimeters) and effective height of 88 mm, weighing not less than 190 gms ( one hundred grams) complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour as directed by the Engineer-in- Charge including carriage of materials within all leads and lifts and other incidentals and as per the entire satisfaction of Engineer-in- charge.

Providing and fixing 600x120x5 mm ( Six hundred into one hundred twenty into five millimeters) glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm ( Forty millimeters) long screws, rawl plugs etc.,complete as directed by the Engineer-in- Charge including carriage of materials within all leads and lifts and other incidentals and as per the entire satisfaction of Engineer-in-charge.

Providing and fixing C P brass toilet paper holder as directed by the Engineer-in- Charge including carriage of materials within all leads and lifts and other incidentals and as per the entire satisfaction of Engineer-in- charge.

Providing and fixing PTMT soap Dish Holder having length of 138mm ( One hundred thirty eight millimeters) , breadth 102mm ( one hundred two millimeters) , height of 75mm ( Seventy five millimeters) with concealed fitting arrangements, weighing not less than 106 gms( one hundred six grams)as directed by the Engineer-in- Charge including carriage of materials within all leads and lifts and other incidentals and as per the entire satisfaction of Engineer-in-charge.

Providing and fixing 15 mm ( Fifteen millimeters) nominal bore C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms( Eight hundred ten grams)as directed by the Engineer-in- Charge including carriage of materials within all leads and lifts and other incidentals and as per the entire satisfaction of Engineer-in- charge.

Providing and fixing PTMT 15 mm ( Fifteen millimeters) nominal bore, 107 mm ( One hundred seven millimeters) long, weighing not less than 110 gms ( One hundred ten grams) pillar cock of approved quality and colour as directed by the Engineer-in- Charge including carriage of materials within all leads and lifts and other incidentals and as per the entire satisfaction of Engineer-in-charge.

Providing and fixing PTMT angle stop cock 15 mm ( Fifteen millimeters) nominal bore, weighing not less than 85 gms as directed by the Engineer-in- Charge including carriage of materials within all leads and lifts and other incidentals and as per the entire satisfaction of Engineer-in-charge.

Providing and fixing PTMT 15 mm ( Fifteen millimeters) nominal bore, 86 mm ( Eighty six millimeters) long, weighing not less than 88 gms ( Eighty eight grams) stop cock of approved quality and colour as directed by the Engineer-in- Charge including carriage of materials within all leads and lifts and other incidentals and as per the entire satisfaction of Engineer-in- charge.

Providing and fixing uplasticised 15 mm ( Fifteen millimetrs) nominal bore 45 cm ( Forty five centimeters) length PVC connection pipe with brass unions as directed by the Engineer-in- Charge including carriage of materials within all leads and lifts and other incidentals and as per the entire satisfaction of Engineer-in-charge.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 20 mm nominal bore

mustak

RAM PAL CHANDEL

ranjit singh

BALRAJ SINGH GOVT CONTRACTOR