PROVN OF FALSE CEILING PROVN OF TWO BATH ROOMS AND EIGHT WC FOR MECHANICAL TRANSPORT PROVN OF SENTRY POST NEAR GATE AT BLDG NO. E-33 AT 16 DOGRA AND TOILETS IN REVENUE WORK AT ARTYCENTRE UNDER GE GOLCONDA

Amount

Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in hard/dense soil all as specified and directed.

Excavation over areas not exceeding 1.5 M deep and getting out in hard / dense soil all as specified and directed.

Excavation over areas exceeding 1.5 M and not exceeding 3 M deep and getting out inhard / dense soil all as specified and directed.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth and getting out in hard/dense soil all as specified and directed.

Returnng, filling in, soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm all as specified and directed.

Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point all as specified and directed.

M&L for hardcore using broken stone or boulders not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface all as specified and directed.

Earth filling under floors including spreading, levelling in layers not exceeding 25cm thick and well ramming including watering as required all as specified and directed. Note: Serviceable earth obtained from excavation shall used for filling.

M & L for Sand filling under floors or in foundations including watering and consolidation all as specified and directed.

M&L Plain cement concrete (1:4:8) type D2 (40mm graded stone aggregate) in foundations, filling and mass concrete all as specified and directed.

M&L for pre-cast Reinforced cement concrete (1:2:4) type B1 (20 mm graded stone aggregate) as in cover slabe for manholes etc., and set in cement mortor (1:4) all as specified and directed. Note: Reinforecement will be measured and paid separately.

M&L for Plain cement concrete (1:3:6) type C1 (20 mm graded stone aggregate) as in coping, benching, bed blocks, cills etc., including necessary form work , complete all as specefied and directed.

M & L for Reinforced Cement Concrete (1:1.5:3) type A1 (20 mm graded stone aggregate) in foundations including rafts, footings and mass concrete, foundation beams, plinth beams, bases for columns, basement slabs etc., complete all as specified and directed.

M & L for Reinforced Cement Concrete (1:1.5:3) type A1 (20 mm graded stone aggregate) in Columns, posts and struts, complete all as specified and directed.

M&L for Reinforced cement concrete (1:1.5:3) (20 mm graded stone aggregate) in lintel bands, roof beams and cantilevers etc., all as specified and directed.

M&L for reinforced Cement Concrete (1:1.5:3) type A1 (20 mm graded stone aggregate) Chajjas, all as specified and directed.

M&L for Reinforced Cement Concrete (1:1.5:3) type A1(20 mm graded stone aggregate) slabs supported on walls, beams and columns in floors, roofs, landings balconies canopies, desk slabs and in shelves etc., complete all as specified and directed.

M & L for pre-cast reinforced cement concrete (1:2:4) type B0 (12.5 mm graded stone aggregate) 40 mm thick Jallies or louvers including all mouldings and set in Cement Mortar (1:4), complete all as specified and directed.

Supply only integral water proofing compound

M&L Brick work with fly ash bricks built in cement mortar (1:6) straight or curved on plan exceeding 6 mtr mean radius all as specified and directed.

M & L Brick work with fly ash bricks, half brick thick wall, straight or curved on plan to any radius built in cement mortar (1:4) complete, all as specified and directed.

M&L for Walling of random rubble masonry, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar (1:6), complete all as specified and directed.

M&L for use & waste formwork to sides of concrete foundations, rafts, footing, base of columns, raft and raft beams, sides & soffits of foundation (if any) of foundation and plinth beams and similar work, flat, rough finished surfaces, complete all as specified and directed.

M&L for use and waste of form work to sides and soffits of floor or roof beams, lintles, cantlevers, shelves etc., flat rough finished surfaces, complete all as specified and directed.

M&L Use & waste of form work to columns, posts, struts and stanchions etc., Square, rectangular or polygonal, flat rough finished surfaces, complete all as specified and directed.

M&L for form work to chullah hoods,chajjas, troughs and similor items including edges, complete all as specified and directed.

M&L for formwork to sides and soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished surface, complete all as specified and directed.

M&L for formwork to edges of concrete flats, treads, breaks in floors,window cills, concrete railings ,openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exceeding 20cm wide rough finished surfaces, complete all as specified and directed.

S&F for solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling and fixing as per specification and drawing all as specified and directed.

S & F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing all as specified and directed.

S&F for 100 mm long extruded Aluminium alloy butt hinges fixed to PVC door shutter.

S&F for 150mm long aluminium anodized barrel tower bolts of extruded section and fixed.

S&F for 150 mm long alluminium alloy anodized handles fabricated type

S & F for tubular towel rail 20 mm dia ‘D’ type 60 cm long between flanges of brass chromium plated.

S & F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete.

S & F Mild steel framed work such as grills, gratings, framed guard bars, ladders etc., with ends of bars shouldered and/ or riveted, or forged into spikes, screen for septic tank and similar work confirming to Fe 290. Gde-E-165 all as specified and directed.

S&F Mild steel TMT bars 6 to 8mm dia and over, cut to length bent to shap required including cranking, bending spirally for hooping for columnshooking ends and binding with and including mild steel wire (annealed not less than 0.9 mm dia or securing with clips

S&F Mild steel TMT bars 10mm dia and over, cut to length bent to shap required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed not less than 0.9 mm dia or securing with clips, all as specified and directed.

All as per item No. 39 Hereinbefore but 5mm dia and over upto and including 10 mm dia in spacers, stirrups and binders

S&F Collapsible steel gates, sliding type, consisting of channel pickets, pivoted flat bars, top and bottom runners, MS handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified and directed.

S & F for rungs, bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates; hook and pintle hinges, large hasps and staples, hains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 all as specified and directed.

S & F true or horizontal level 600mmx600mm panels, false ceiling, hot dipped galavnised steel sections exposed suface with precoated capping, main tee and cross tee of size 24x32mm at every 1200mm c/c and wall angle of size 19x19mm fixed to perimetere wall, as per manufacturer's instructions, grid to be suspended at every 1200mm c/c in both directions by using 2mm dia pre-straightened GI wire at every 1200mm internal at the main tee, including 9mm thick gypsum board of size 600mm X 600mm with rear size aluminium foil and front side PVC lamination, complete all as specified and directed.

M&L Plain cement concrete (1:4:8) type D2 (40mm graded stone aggregate) 75mm thick as in sub base of flooring/hardstanding complete all as specified and directed.

M&L for chequred cement concrete tiles 30 cm x 30 cm x 25 mm thick with grey cement and pigment, machine pressed : set, jointed and pointed in neat cement slurry, laid over including 15 mm thick screed bedding layer in cement mortar (1:6) all as specified and directed.

M&L Plain cement concrete (1:2:4) type B0 (12.50mm graded stone aggregate) 25mm thick, as padding concrete on roof/sub base of flooring/damp proof course etc., complete all as specified and directed. Note: Damp proof course/roof padding will be mixed with water proofing compound. Supply only WPC will be measured and paid separately.

S&F for non skid coloured ceramic tiles 7 to 8mm thick (square or rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm, in floors laid over and including 15mm thick screed bed or bedding layer in cement mortar (1:6), tiles jointed in neat cement slurry and pointed with white cement mixed with pigment to match the colour of tiles all as specified and directed.

S&F for glazed ceramic coloured tiles of size 300x200x7mm thick for vertical surfaces as in dado/skirtings set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles laid over and including backing coat in cement mortar (1:4), 10mm thick all as specified and directed.

M & L Plain Cement concrete (1:3:6) type C2 (40 mm graded stone aggregate ) as in plinth protection finished even aned smooth without using extra cement, complete all as specified and directed.

M&L Plain cement concrete (1:2:4) type B1 (20mm graded stone aggregate), 75mm thick as in path/pavings/hard standing finished even and smooth surface without using extra cement complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 20 -25mm thick, laid over and including 15mm thick cement screed bed or bedding in cement mortar (1:6) and jointed and pointed with grey cement slurry mixed with pigment to match the shade of the slab as in platform, shelves and flooring including rubbing and polishing complete all as specified and directed.

M&L for Rendering 15mm thick in cement mortar (1:4) on fair faces of brick work / concrete surfaces finished even and smooth without using extra cement, mixed with water proofing compound, complete, all as specified and directed. Note: Supply only water proofing compound will measured and paid separately.

M&L Rendering 10mm thick on brick work or concrete surface in cement mortar (1 : 6) and finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 5 mm thick in ceilings with cement mortar (1:3) and finished even and smooth without using extra cement, complete all as specified and directed.

M & L for Preparation of new plastered wall surfaces and apply three coat of white wash, complete all as specified and directed.

M & L Preparation of new plastered ceiling surfaces and apply three coats of white wash, complete all as specified and directed.

M&L for preparation of new plastered wall surfaces and apply two coats of cement based paint over a coat of cement primer all as specified and directed.

M&L Figured, pin headed type, 3mm thick, glazing with oil putty in squares not exceeding 0.5 Sqm in each pane all as specified and directed.

M&L Preparation of new steel surfaces of area exceeding 10cm width & girth and apply two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer all as specified and directed.

M&L Preparation of new or previously untreated steel surfaces of any description, not exceeding 10 cm width or girth, not otherwise described and apply two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer all as specified and directed.

M&L for salt glazed stone ware drain pipes, 150mm internal diameter of the pipe, grade'A', laid in trenches and jointed as specified all as specified and directed.

M&L for salt glazed stone ware drain pipes, 100mm internal diameter of the pipe, grade'A', laid in trenches and jointed as specified all as specified and directed.

M&L Plain cement concrete(1:3:6) type C2(40mm graded stone aggregate) as bed to drain pipes, 150mm bore dia, including packing under,and haunching against the sides of pipes after they are laid and tested; complete all as specified and directed.

M&L Plain cement concrete(1:3:6) type C2(40mm graded stone aggregate) as bed to drain pipes, 100mm bore dia, including packing under,and haunching against the sides of pipes after they are laid and tested; complete all as specified and directed.

S & F for vitreous china squatting pan (Orissa pattern) size 580 X 440mm white with integral foot rest, P or S trap complete all as specified and directed.

S & F of PVC valveless, syphonic action type, flushing cistern, dual operated type, 10 ltr capacity, low level, white with inlet ball valve float and handle including brackets, with 32mm dia PVC pipe, complete all as specifeid and directed.

S&F for 15 mm dia PVC connections with PTMT nuts of length 450 mm, with check nuts complete all as specified and directed.

S&F for stop valve 15mm bore cast copper alloy but fancy type chromium plated with cup screwed down high pressure fixed to iron pipes or for unions.

S&F for stop valve(angle cock) 15mm bore cast copper alloy but fancy type chromium plated with cup screwed down high pressure fixed to iron pipes or for unions.

S&F for fancy CP bib tap15 mm bore, cast copper alloy with screwed down, screwed for iron pipe or for brass ferrule.

S&F Rotational moulded polyethylene water storage tanks, of capacity 1000 litres (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I, complete all as specified and as directed

S&F Rotational moulded polyethylene water storage tanks, of capacity 500 litres (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I, complete all as specified and as directed

S&F 20 mm dia Ball valves high pressure of PTMT with epoxy coated aluminum rod and high density plastic ball screwed for iron pipe, 20mm bore (Min wt 210 gms) complete all as specified and as directed.

S&F steel water tubing, ‘medium grade’ galvanised, 15mm bore including all fittings to walls and ceilings or laid in floors, complete all as specified and as directed.

S&F steel water tubing, ‘medium grade’ galvanised, 20mm bore including all fittings to walls and ceilings or laid in floors, complete all as specified and as directed.

S&F steel water tubing, ‘medium grade’ galvanised, 25mm bore including all fittings to walls and ceilings or laid in floors, complete all as specified and as directed.

S&F steel water tubing, ‘medium grade’ galvanised, 40mm bore including all fittings to walls and ceilings or laid in floors, complete all as specified and as directed.

S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20mm bore, complete all as specified and as directed by Engineer-in-charge.

S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe 25mm bore, complete all as specified and as directed by Engineer-in-charge.

S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe 40mm bore, complete all as specified and as directed by Engineer-in-charge.

S & F for 110 mm PVC (SWR) junction single (Single T) equal or unequal with access Door

S & F for 110 mm PVC (SWR) bends any radius all as specified and directed.

S & F for 110 x 75 mm PVC (SWR) reducer

S & F for 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors / walls

S & F for 110mm PVC (SWR) vent cowl

S&F 125mm dia brass chromium plated shower rose with or without swivel joints including fixing to steel pipe or union

PVC (SWR) floor trap 75mm dia, plain with gratings including jointing with solvent cement

S&F wash down water closet (pedestal pattern) complete white with plastic water closet seat black closed pattern with flat bottom anc cover and mild steel chromium plated or aluminised hinging device and flush pipe of polythelene of low or density or PVC 32mm dia for low level flushing cistern complete

S & F for Vitreous china Urinal bowl flat back , size of 465x355x265mm white (minimum) with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete as directed

S&F PVC waste pipe for urinal / WHB with complete fitting etc 38 mm dia.

S&F for vitreous china wash basin, white, flat back size 550 x 400mm including 01 Nos cast copper alloy 15mm fancy type, long body CP pillar tap, 01 Nos 32mm waste coupling and pipe, one pair of MS bracket, cutting for and pinning in ends of brackets or erecting stand complete.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/floor 110mm bore

S&F PVC (SWR) bends any radius with access doors 110mm bore

S&F PVC (SWR) bends any radius 75mm bore

S&F PVC (SWR) bends any radius with access doors 75mm bore

S&F PVC (SWR) junction single, (Single T) equal or unequal with access door 75 mm bore

S & F brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete

S & F in health faucet with spray jet (hand shower) cromium plated incl all fitting & fixtures complete all as specified

S&F in two way bib cock/tap 15 mm chromium plated complete fancy type of branded as specified and directed.'

S & F 32mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed

M&L salt glazed stone wave gully traps square or rounded mouthed type & fix 150 x 150 mm fixed in cement concrete complete

Cutting in to existing manholes for connecting new drains making good to pipe 100mm internal dia and rendering cutting out existing benching for and forming branch channel(1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching, complete all as specified and directed.

S & F for Asbestos cement pipes in any length with cement joints; fixed to walls / slab as vent pipe

S & F for AC Slotted vent cowl

M&L Point wiring for one light point/fan point/bell point controlled by one switch with 1.5 sqmm multistrand copper conductor cable PVC (FRLS) insulated unsheathed copper conductor single core multi stand flexible cable and 1.50 sqmm PVC (FRLS) insulated unsheathed copper conductor single core cable ( green colour) as earth lead in and including PVC rigid conduit with all fittings for concealed type on stone / brick ,masonary walls, roof etc including in new MS sunk box of required size and all as directed by Engineer-in-Charge & 2 mm thick plastic laminated sheet for housing switches sockets, regulators etc, including running chases, pinning in and making good the disturbed surfaces to match with the existing specification ,complete all as specified and directed at site.

All as per item No. 106 hereinbefore but for One 3 pin 15 / 16 Amps switch socket outlet point on independent board with 2.5 sqmm PVC (FRLS) insulated unsheathed copper conductor single core multi stand flexible cable and 2.5 sqmm PVC (FRLS) insulated unsheathed copper conductor single core cable (green colour) as earth lead complete all as specified and directed.

M&L switch piano flush type single pole one way 5 Amps complete all as specified and directed.

M&L lamp holder insulated body with back plate suitable for battern fittings complete all as specified and directed.

S&F Ceiling rose surface bakelite 65 x 50 mm 2/3 terminais complete all as specified and directed.

S&F LED tube light fittings 1 x 20 W, 230V, complete with all accessories internally prewired and including LED Tube rod connecting up with twisted flexible PVC copper conductor cable of 23/0.0076 from ceiling rose all as specified and directed. (Make Havells : Cat No: LHFYDBWPITBW020 (Batten) and LHEDDAXEUL82018 (Tube Rod) or equivelent in Philips / Crompton Greaves)

S&F Sheet metal enclosure MCB distribution board including 200 Amps bus-bar single pole and neutral 240V, 2 Ways, including existing sheet metal enclosure complete all as specifide and directed.

S & F Bulk head fitting 10W luminaires with all accessories including lamp holders etc complete with one No 10 watts LED bulb and connecting up with twin core twisted flexible PVC copper conductor cable of size 23/0.0076 from ceiling rose all as specified.

S&F LED lamp 5W, 240V all as specified and directed.

M&L Switch socket combination 2 in 1 flush type universal 3 pin 5 & 15 Amps complete all as specified and directed.

S&F MCB single pole and neutral 6 to 32 Amps 240 Volts complete all as specified and directed.

S&F MCB single pole 240 Volts 6 to 32 Amps complete all as specified and directed.

S&F LED Building security lights New generation energy saving & enviromental friendly long life versitile pressure die cast aluminum roadway luminarie with high power LEDS 20 watts as light source and electronic driver bracket made into required shape for fittings complete with MS clamp, nuts and bolts and washsers as required at site of minimum 1.5 mtr long Med grade GI pipe 40 mm dia including painting with one coat of primer and two coat of aluminium paint complete all as specified and directed. Make :Havells cat part no:LHEWEBP7PL6S020 are Eqivalent to PHILIPS / WIPRO / CROMPTON GRAVES / BAJAJ.

Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 mtr below ground level) with top edge o the plate not less1.5 mtrs below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts nuts, check nuts and washers of galvanized iron of steel all as shown in electrical plate No.3 connected to earthing test point incl necessary earth work, excavation PCC 1:3:6 type CI using 20mm graded stone aggregate for earth chamber provn of PCC cover 40 mm thick 1:2:4 mm type B1 funnel with water Pipe, GI pipe, 15mm dia medium grade protection pipe, GI earth lead complete all as specified and directed by the Engr-in-charge.

Supply, fixing and testing exhaust fan heavy duty type single pahse 230 volts 50 Hz of 300mm sweep SP Turbojet of 900 RPM with metal body and blade complete all as specified and directed

Supply and fixing geyser for new generation energy saving & environmental friendly long life versitile pressure die cast capacity 25 Liters BEE 5 Star rated including all fitting and fixtures complete all as specified and directed

M&L House service bracket (hook type complete with 3.0m long G.I pipe 40mm dia Medium grade, two Nos 90 degree bend M.S hook and stay or guy including taking down of old unserviceable one all complete all as specified and directed

S&F 1100 V grade heavy duty cable PVC insulated aluminium stranded conductor served with inner sheathing of PVC tape and over all PVC sheathed twin core cable flat or circular stranded conductor of size10 Sqmm in service connections suspended by insulated hangers not more than 1 mtr apart incl 4 mm GI suspension wire complete with all as specified and directed.

All as per item No. 123 here-in-before but size 6 Sqmm

STANDARD AGENCIES

Sri Lakshmi Enterprises