Construction of Rajkiya High School Khakora Block Mauranipur Jhansi

High School building

Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap).

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Cement concrete in 1:4:8 with cement, sand and 4cm .(1.5") gauge Approved granite stone ballast (crusher broken) in foundation including supply of all materials, labours and T&P etc. required for proper completion of work.

M 150 brick work in 1:6 cement and Coarse fine sand mortor in foundation and plinth i/c all complete as chapter 6 as S.I. No 303

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources) pile cap

Providing and injecting chemical for pre-constructional anti-termite treatment and chemical barrier under and around the coloumn pits wall trenches basement excavation top surfaces if plinth filling junction of wall and floor, along the external per meter of binding expansion joints surrounding of pipes and conduit etc, complete .

R.C.C work in 1:1½:3 cement approved coarse sand and 20 mm gauge granite stone gritt for Plinth Beam excluding supply of reinforcement and its bending but including its fixing and binding the same with 24 B.W.G.G.I. binding wire and including necessary centering and shuttering etc. also including supply of all materials,labour and T&P etc. required for proper completion of the work .Binding wire cost being included in the item.

Providing and laying damp proof course 2.5 cm thick with cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 10 mm ) and curing complete

Providing & applying a coat of residual petoleum bitumen of grade of vg-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a plece of cloth lightly soaked in kerosene oil.

Reinforced cement concrete work in beams suspended floors, roofs having slope up to15 landings balconies shelves chajjaa lintels bands plain windows sills staircases and spiral stair cases above plinth level up to floor five level excluding the cost of centering shuttering and reinforcemnet with 1:1.5:2(1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size Lintel Band

Reinforced cement concrete work in beams suspended floors, roofs having slope up to15 landings balconies shelves chajjaa lintels bands plain windows sills staircases and spiral stair cases above plinth level up to floor five level excluding the cost of centering shuttering and reinforcemnet with 1:1.5:2(1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size R.C.C Work in Slab

Reinforced cement concrete work in beams suspended floors, roofs having slope up to15 landings balconies shelves chajjaa lintels bands plain windows sills staircases and spiral stair cases above plinth level up to floor five level excluding the cost of centering shuttering and reinforcemnet with 1:1.5:2(1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size R.C.C work in beam

Reinforced cement concrete work in beams suspended floors, roofs having slope up to15 landings balconies shelves chajjaa lintels bands plain windows sills staircases and spiral stair cases above plinth level up to floor five level excluding the cost of centering shuttering and reinforcemnet with 1:1.5:2(1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size R.C.C Columm

M 150 brick work in 1:6 cement and Coarse sand of mortor in s/s in one brick thick wall including supply of all materials , labours and T&P etc. required for proper completion of the work.

115 mm brick work in 1:4 cement and Coarse sand of mortor in s/s in one brick thick wall including supply of all materials , labours and T&P etc. required for proper completion of the work.

Mild steel or iron in plain work such as reinforced concrete wrought to required same as necessary including bending for proper completion of the work.

15mm thick plaster in 1:6cement mortar over brick work minimum thickness not to be less than 3/6”(12mm) thick including supply of all materials labour and T&P etc. required for proper completion of the work for proper completion of the work but with cement and approved coarse sand in 1:6 cement & fine sand of 1.25 F.M. mortar.in external

12mm thick plaster in 1:6cement mortar over brick work minimum thickness not to be less than 3/6”(12mm) thick including supply of all materials labour and T&P etc. required for proper completion of the work for proper completion of the work but with cement and approved coarse sand in 1:6 cement & fine sand of 1.25 F.M. mortar.in wall.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand),jointing with grey cement slurry @ 3.3 kg/ sqm including grouting thejoints with white cement and matching pigments etc., complete

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand),jointing with grey cement slurry @ 3.3 kg/ sqm including grouting thejoints with white cement and matching pigments etc., complete

Provinding and laying caremic glazed floor tiles of the 300x300 mm (thickness to be specified by the manufacture) of 1st quality conforming to IS: 15622 of approved make in colour such as white, ivory, grey, fume red brown, laid on 20mm thick cement mortar 1:4(1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching plehment etc

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Kota stone flooring over 20mm (average) thick base laid over kounted with grey cement slurry mixed with pigment to math the shede of the slab, including rubbing and plishing complete with vase of cement mortar 1:4(1cement :4 coarse sand) 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab

Providing and fixing 18 mm thick gang saw cut, mirror polished,premoulded and prepolished, machine cut for kitchen platforms, vanitycounters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cementmortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement,mixed with matching pigment, epoxy touch ups, including rubbing, curing,moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm (Granite of any shade)

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: (a) single leaf- (35mm thick)

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: (b) Double leaf- (35mm thick)

Mild steel or iron work of small sizes and section such as holding down bolts, hold fast tie rods, gratings etc. (when not included in an over all rates) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing, Providing & fixing of doors / windows grill

Mild steel or iron work of small sizes and section such as holding down bolts, hold fast tie rods, gratings etc. (when not included in an over all rates) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing, Z- Section Steel windows

Mild steel or iron work of small sizes and section such as holding down bolts, hold fast tie rods, gratings etc. (when not included in an over all rates) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing, Angle iron door Chaukhats

Distempering ( two coat) with oil bound distemper of approved beand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer or approved brand & manufacture such as berger, j&N, Shalimar, asian paints after thoroughly brushing the suface from mortar droppongs & other foreign matters & also including preparing the surface material & sand papered smooth including cost of all material

Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Providing and laying "brick coba" 120 mm thick laid with M-150 class brick bat coba 7.50cm thick with gap of 15mm to each other, over 20 mm thick base of cement mortar 1:4 cement and coarse sand mixed with water proofing compound spreading cement slurry mixed with acrelic cement concrete water proofing compound filled gaps of coba & top of coba mortar mixed with water proofing compound in 1:4 cement and coarse sand finised smooth & top mashed false square 30 cm x 30 cm and side wall parapet shall be mono tythic plaster wall up to 30 cm higher and junction and corner shall be rounded by brick ballast cement and coarse sand masonany Coba with top finised plaster mixed with acetic water proofing compound @ 2% by weight & including s/o all material, labour, T& P etc complete for proper completion of work.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows all complete. With 4.0 mm thick glass panes

Providing and fixing in posltion collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail ofl T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handies, including applying a priming coat of

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand)

Centering & shuttering including strutting, propping etc. and removal of form for all heights: Suspended floors, roofs, landings, balconies and access platform.

Centering & shuttering including strutting, propping etc. and removal of form for all heights: Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Centering & shuttering including strutting, propping etc. and removal of form for all heights: Columns,Pillars, Piers, Abutments, Posts and Struts.

Providing and fixing U. p.v.c rain water pipe 110mm dia with shoe,door bend etc.

Providing and fixing of wall face unplastiside PVC mold fitting accessories for unplastiside rigid PVC rain water pipe coforming including joint with seal ring conforming to leaving 10 mm gap to thermal expension Cuppler (110 mm)

Appron Work

Supply and filling of Moorum soil in plinth protection /appron

Brick work in 1:6 cement:sand moratr in Appron

Lean concrete in 1:4;8 in appron

25 mm p.c.c.flooring in 1:2;4

Providing & fixing Glass sttirups in flooring

Door Fitting

Providing and fixing I.S.I. mark oxidised M.S. tower bolt finish (Barrel type) with necessary screw etc complete (150 x 100 mm)

Providing and fixing I.S.I. mark oxidised M.S. Sliding door bolt with nut and screw etc complete (250 x 16 mm)

Providing and fixing I.S.I. mark oxidised M.S. Handles conforming to with nut and screw etc complete (100 mm)

Appron Drain

Earth work in exacavation in trenches for foundations land for pipes cables etc. in ordinary soil (loan clay or sand) including lift upto 1.5 m and dressing of sides and ramming of bottom sand disposal of surplus excavated earth as directed by the Engineer i/c with in a lead of 50m.

Providing and laying in cement concrete 1:4:8(1 cement :4coarse sand :8 graded stone aggregate 40 mm nominal size) and curing complete, including cost of form-work, in foundation and floors.

Class 150 Brick Work in 1:4 cement and coarse sand of 2.20 fineness modulus mortar in foundation and plinth including supply of all materials, labour and tools and plants etc. required for proper completion of the work.

12 MM Th. Cement plaster 1:3 (cement & C.sand) with Neat Cement Finish

Toilet Block Ground Floor

Site clearing cutting jungle uprooting roots grass vegetation etc.

Boring with hydraulic piling rigs with power unit ,providing and ininstalling cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete ,to carry of safe working load not less than specified .excluding the cost of steel reinforcement bul including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete (length of pile for payment shall be measured upto to the bottom of pile cap)

Filling of carted earth

Cement concrete in 1:4:8 with cement, sand and 4cm .(1.5") gauge Approved granite stone ballast (crusher broken) in foundation including supply of all materials, labours and T&P etc. required for proper completion of work.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and injecting chemical for pre-constructional anti-termite treatment and chemical barrier under and around the coloumn pits wall trenches basement excavation top surfaces if plinth filling junction of wall and floor, along the external per meter of binding expansion joints surrounding of pipes and conduit etc, complete .

Reinforced cement concrete work in beams suspended floors, roofs having slope up to15 landings balconies shelves chajjaa lintels bands plain windows sills staircases and spiral stair cases above plinth level up to floor five level excluding the cost of centering shuttering and reinforcemnet with 1:1.5:2(1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size

Lintel Band

R.C.C Work in Slab

R.C.C work in beam

M 150 brick work in 1:6 cement and fine sand of 1.25 F.M. mortar in foundation and plinth including supply of all materials, labours and T&P etc. required for proper completion of the work .(Edging)

M 150 brick work in 1:6 cement and Coarse sand of mortor in s/s in one brick thick wall including supply of all materials , labours and T&P etc. required for proper completion of the work.

115 mm brick work in 1:4 cement and Coarse sand of mortor in s/s in one brick thick wall including supply of all materials , labours and T&P etc. required for proper completion of the work.

Providing and laying damp proof course 2.5 cm thick with cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 10 mm ) and curing complete

Providing & applying a coat of residual petoleum bitumen of grade of vg-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a plece of cloth lightly soaked in kerosene oil.

Mild steel or iron in plain work such as reinforced concrete wrought to required same as necessary including bending for proper completion of the work.

15mm thick plaster in 1:6cement mortar over brick work minimum thickness not to be less than 3/6”(12mm) thick including supply of all materials labour and T&P etc. required for proper completion of the work for proper completion of the work but with cement and approved coarse sand in 1:6 cement & fine sand of 1.25 F.M. mortar.in external

12mm thick plaster in 1:6cement mortar over brick work minimum thickness not to be less than 3/6”(12mm) thick including supply of all materials labour and T&P etc. required for proper completion of the work for proper completion of the work but with cement and approved coarse sand in 1:6 cement & fine sand of 1.25 F.M. mortar.in wall.

Cement concrete flooring 1:2:4 ( 1cement :2 coare sand : 4 graded stone aggregate) finished with a floting coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. Complete. (40 mm thick floor

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand),jointing with grey cement slurry @ 3.3 kg/ sqm including grouting thejoints with white cement and matching pigments etc., complete

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand),jointing with grey cement slurry @ 3.3 kg/ sqm including grouting thejoints with white cement and matching pigments etc., complete

Provinding and laying caremic glazed floor tiles of the 300x300 mm (thickness to be specified by the manufacture) of 1st quality conforming to IS: 15622 of approved make in colour such as white, ivory, grey, fume red brown, laid on 20mm thick cement mortar 1:4(1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching plehment etc

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: (a) single leaf- (35mm thick)

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: (b) Double leaf- (35mm thick)

Mild steel or iron work of small sizes and section such as holding down bolts, hold fast tie rods, gratings etc. (when not included in an over all rates) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing, Providing & fixing of hold fast for chaukhats of doors and windows.

Mild steel or iron work of small sizes and section such as holding down bolts, hold fast tie rods, gratings etc. (when not included in an over all rates) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing, Providing & fixing of doors / windows grill

Mild steel or iron work of small sizes and section such as holding down bolts, hold fast tie rods, gratings etc. (when not included in an over all rates) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing, Z- Section Steel windows

Mild steel or iron work of small sizes and section such as holding down bolts, hold fast tie rods, gratings etc. (when not included in an over all rates) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing, Angle iron door Chaukhats

Distempering ( two coat) with oil bound distemper of approved beand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer or approved brand & manufacture such as berger, j&N, Shalimar, asian paints after thoroughly brushing the suface from mortar droppongs & other foreign matters & also including preparing the surface material & sand papered smooth including cost of all material

Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Providing and laying "brick coba" 120 mm thick laid with M-150 class brick bat coba 7.50cm thick with gap of 15mm to each other, over 20 mm thick base of cement mortar 1:4 cement and coarse sand mixed with water proofing compound spreading cement slurry mixed with acrelic cement concrete water proofing compound filled gaps of coba & top of coba mortar mixed with water proofing compound in 1:4 cement and coarse sand finised smooth & top mashed false square 30 cm x 30 cm and side wall parapet shall be mono tythic plaster wall up to 30 cm higher and junction and corner shall be rounded by brick ballast cement and coarse sand masonany Coba with top finised plaster mixed with acetic water proofing compound @ 2% by weight & including s/o all material, labour, T& P etc complete for proper completion of work.

Painting two coat over priming coat (but including cost of priming coat) on steel and other metal surfaces up to 10 cm. width or girth or small articles not exceeding 0.10sqm in area white superior synthetic enamel such as LUXOL3, Hi-gloss apcolite superlac, DULUX specified brushing to give an even shade and including cleaning the surface of all dirt, dust and other foreign matter sand papering and stopping including.

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows all complete. With 4.0 mm thick glass panes

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand)

Making grooves 12 to 12mm widex 8mm deep in plaster of the wallor in celling vertically or horizontally as required.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

Centering & shuttering including strutting, propping etc. and removal of form for all heights: Suspended floors, roofs, landings, balconies and access platform.

Centering & shuttering including strutting, propping etc. and removal of form for all heights: Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Door Fitting

Providing and fixing I.S. 12817 maked stainless steel but hinges with stainless steel screw etc. complete (100 x 58 x 1.9 mm)

Providing and fixing I.S.I. mark oxidised M.S. tower bolt finish (Barrel type) with necessary screw etc complete (150 x 100 mm)

Providing and fixing I.S.I. mark oxidised M.S. Sliding door bolt with nut and screw etc complete (250 x 16 mm)

Providing and fixing I.S.I. mark oxidised M.S. Handles conforming to with nut and screw etc complete (100 mm)

Aluminium Sliding Door

Appron Drain Work

Earth work in exacavation in trenches for foundations land for pipes cables etc. in ordinary soil (loan clay or sand) including lift upto 1.5 m and dressing of sides and ramming of bottom sand disposal of surplus excavated earth as directed by the Engineer i/c with in a lead of 50m.

Providing and laying in cement concrete 1:4:8(1 cement :4coarse sand :8 graded stone aggregate 40 mm nominal size) and curing complete, including cost of form-work, in foundation and floors.

Class 150 Brick Work in 1:4 cement and coarse sand of 2.20 fineness modulus mortar in foundation and plinth including supply of all materials, labour and tools and plants etc. required for proper completion of the work.

12 MM Th. Cement plaster 1:3 (cement & C.sand) with Neat Cement Finish

Sanitary & Water Supply

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level whiteP.V.C. flushing cistern, including flush pipe, with manually controlleddevice (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required :

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing P.V. C. Pipe 6kg.Pis including all Material, Labour T.&P. Complete of work. 110 mm dia.

Providing and fixing P.V. C. Bend including all Material, Labour T.&P. Complete of work. For 110 mm dia.

Providing and fixing P.V. C. N Trape including all Material, Labour T.&P. Complete of work. 100*100mm.

Providing and fixing of P.V.C. Copler For 110 mm dia.

Providing and fixing of P.V.C. Tee For 110 mm dia.

Providing and fixing of P.V.C. Door Bend For 110 mm dia.

Providing and fixing of P.V.C. Clamp For 110 mm dia.

Providing and fixing of P.V.C. Covel 90mm. Ddia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge Concealed work, including cutting chases and making good the walls etc. 15 mm dia. nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge Concealed work, including cutting chases and making good the walls etc. 20 mm dia. nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge Concealed work, including cutting chases and making good the walls etc. 25 mm dia. nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions : 15 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) 20 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) 25 mm nominal bore

Cutting holes upto 30x30 cm in walls including making good the same : With F.P.S. bricks.

Providing and fixing C.P. brass long body /shortbody bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 as Such Hindwair 15 mm nominal bore

Providing and fixing of C.P. towel rod 24"heavy.

Handicap kit

Sanitary and Water Supply (External)

Providing & Laying of 160mm. Dia P.V.C. pipe 6kgcm Sewer Line including excavation of Tranch Providing 1:4:8 cement Concrete P.C.C. Base & Pipe covered with P.C.C. 1:2:4 including all Labour, T.&P. complete of work

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 60x60 cm and 75 cm deep

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc32mm.dia

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Construction of Septick tank 50 USER Size as per ISI Standered 5.00x1.60x1.40

Earth work in excavation in foundation/tank

Base concrete in 1:4:8 cement:sand:stone ballast

Brick work in 1:4 cement:sand mortar in septick

Brick work in 115mm wall in 1:4 cement : sand mortar

R.c.c. work in 1:1.5:3 cement:sand:stone grit in Slab and beam

Providing cutting beding MS bar Reinforcement in slab

20mm plaster in 1:3 cement:sand mortar with neat cement finish

P.c.c. in 1:2:4 cement:sand :stone grit in base to making slope

Providding and fixing C.I. man hole chembar 600x600mm size in slab

Providing and fixing C.I. vent pipe 100mm dia

Providing and fixing c.i. cowel guard 100mm dia

Providind and fixing 150mm dia inlet and out let pipe

SUBMERSIBLE PUMP

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart bore log, including hire & running charges of all equipments, toois, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level. 300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 100 mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 100 mm nominal size dia

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Development of tube well in accordance with IS: 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit) with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, ic disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 100 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 100 mm clamp.

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubeweli as per IS:2800 (part 1). 100 mm dia.

Supply of submersible pump of make KSB 1.0 HP with control panel, support wire etc. complete.

Providing 2 core PVC insulated submersible cable from pump panel to submersible pump

Providing and foxing GI pipes complete with G.I. fittings including trenching and refilling etc. 32 mm dia nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approvedquality (screwed end)

Internal Electrification work

Wiring for light point/fan point /exhaust fan point /call bell/Sodium point with 1.50 Sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable G I box and earthing the point with 1.50 sq. mm FRLS PVC insulated copper conductor single core etc. as required. Group C

Wiring for Circuit/Submain wiring along with earth wire with the Following size FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit as required. 2 x 1.5 sq. mm + 1 x 1.5 sq. mm earth wire

Wiring for Circuit/Submain wiring along with earth wire with the Following size FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit as required. 2 x 4 sq. mm + 1 x 4 sq. mm earth wire

Wiring for Circuit/Submain wiring along with earth wire with the Following size FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit as required. 2 x 6 sq. mm + 1 x 6 sq. mm earth wire

Wiring for Circuit/Submain wiring along with earth wire with the Following size FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit as required. 4 x 10 sq. mm + 2 x 6 sq. mm earth wire

Supplying and Drawing following sizes of FRLS PVC insulated copper conductor single core cable in the existing surface / recessed medium class PVC conduit as required. 3 x 1.5 Sq.mm

Supplying and Drawing following sizes of FRLS PVC insulated copper conductor single core cable in the existing surface / recessed medium class PVC conduit as required. 3 x 4 Sq.m

Supplying and fixing suitable size G I box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing of following modular switch / socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required. modular base and cover plate for modular switches in recess etc. as required. 5 / 6 A Switch

Supplying and fixing of following modular switch / socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required. modular base and cover plate for modular switches in recess etc. as required. 3 pin 5 / 6 A socket outlet

Supplying and fixing 5 A to 32 A rating, 250 / 415 V, 10 Ka, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. required. Single pole

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. required. 40 Amp.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface / recess, complete with tinned copper bes bar, neutral bus bar, earth bar, din bar,interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way, double door

Supply and fixing of Following way , surafce / recess,Vertical type ,415 v TPN MCB distribution board of sheet steel , dust protected duly powder painted , including of 200 a tinned copper bus bar , comman neutal link , earth bar , din bar for mounting MCBs etc. as required 6 way(4+12) Double door

Supply and fixing of Following way , surafce / recess,Vertical type ,415 v TPN MCB distribution board of sheet steel , dust protected duly powder painted , including of 200 a tinned copper bus bar , comman neutal link , earth bar , din bar for mounting MCBs etc. as required 63 amp FP isolator

Installation, testing and commissioning of ceiling fan, including wiring of the down rods of standard length (upto 30 cm) with 1.50 sq. mm, FRLS PVC insulated, copper conductor, single core cable including providing and fixing phenolic laminated sheet cover on the fan box etc.. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc.. as required. Upto 450 mm sweep.

Supplying and fixing suitable size G I box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junctior pox/ wooden block including connections etc. as required. Each

Supplying and fixing brass batten/ angle holder including connection etc. as required

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but modular plate etc. as required.

Supply & Laying of Aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. Including excavation and refiling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 25 sq.mm x 3½ core.

Supply and fixing of recess / surface mounting round 15 to 18 Watt cut out min 150 mm, Height Min 40 mm, LED Down lighter having with heat sink, diffuser die cast aluminium housing with heat sink, diffuser/Reflector and driver set, suitable for 24 Hr. Continuous Operation, complete in all respect. CAT: AAA, 1980 - 2200 system lumens, 110 lm/W, PF>0.95, THD<10%, at full load, CRI>80, with 5 year warranty.

Supply & fixing of 2' x 2' , 36 Watt to 46 Watt, indoor recess / surface mounting LED Square fitting for Armstrong ceiling having Powder coated CRCA housing body diffuser of special polycorbonate meterial and driver set,complete in all respects.CAT: AAA, 3960 - 5060, 70 mm height with fully covered diffuser type, system lumens, 110 lm/W, PF>0.95, THD<10%, at full load, CRI>80, with 5 year warranty.

Supply and fixing of LED Tube Light with Metal heavy duty box type batten Light fitting 1 x 22 watt suitable for upto 1 x 22 watt LED Polycarbonate tube light complete including tube suitable for both surface & suspended complete in all respect. 2420 system lumens, 110 Lm/watt, PF > 0.95, THD<10%, at full load CRI>80, Tube with aluminium sink hit with 3 year warrantee Cat AA

Supply and fixing of water tight oblong 10 watt LED bulkhead luminaire having die cost housing with driver set confirming to IP 65 and above protection. complete in all respect. 1100 system lumens, 110 Lm/watt, PF > 0.95, THD<10%, at full load CRI>80, with 3 year warrantee Cat AA

Supply and fixing of LED Street light fitting having die cast aluminium body and diffuser with driver set suitable for 60 to 72 watt. Confirming to IP 66 and above Protection complete in all respect. 7200-8640 system lumens, High power LED with lenses, 120 Lm/watt, PF> 0.95, THD<10%, at full load, CRI>70, > 440 V & >300 V autocut & restarts feature with 5 year warrantee Cat AAA

S/F of 50 Amp. to 63 Amp. SPMCB (10 KA) Cat-B

S/F of surface/Flush mounting 4 ways V TPN distribution board with additional door without DPX3 160 MCCB complete in all respect, as directed at site by Engineer in charge. Cat.-B

S/F of 80 Amp. To 100 Amp. 4 pole MCCB (16 KA) Thermal Magnetic release. Cat-B

Supply & Laying of 25 mm x 3 mm G.I. Strip from earth electrode directly in the ground as required complete in all respect.

Supply and burring of Safe Earthing Electrode T-19, (Hot Dip Galvanized), Length up to 3000 mm, Outer Dia 50 mm, inner Dia 25, terminal Dia 12 mm, outer G.I. pipe of 16 swg and inner G.I. pipe of 12 swg with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity and one earthing lead of 25 mm x 3mm G.I. strip upto switch board (from apron to switch board, the cost of G.I. strip will be extra) along with 30 cm square C.I. frame with hinged cover & masonry housing.

Supply and fixing of 16 gauge M S drum with louvers duly painted including making hole in the wall for exhaust fan and finishing properly complete in all respects .

Supply and fixing of crimping, solderless, copper tin electroplated lugs of Dowells/Ismail make suitable for 1.5 sq.mm to 25 sq.mm cables, including tapping with insulating tape, complete in all respect.

S&F of Fire extinguisher, ABC Type 6.00 Kg. capacity (ISI marked IS: 15683 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.

S&F of Co2 type Fire extinguisher, 4.5 Kg. capacity (ISI marked IS: 2878 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.

Supply and fixing of fire bucket, round bottom made of G.I. sheet 9-11 litres capacity duly painted as per fire brigade design, supported on hanging bracket chained and locked, initially filled with fine river sand, water as per directions of Engineer-in-Charge.

S&L of 1800 mm x 900 mm x 12 mm thick chequered rubber matting of tested quality.

S&F of shock treatment chart (Prescribed under I.E Rule) duly framed with glass and supported from back with hard board or soft board with supply of all material labour T&P for proper completion of work.

63 amp TPMCB CAT-B

Supply and fixing of hexagonal / round G P fan box of approved make made up 1.0 mm thick ISI Marked G.P. sheet spot welded four to Eight holes of 25.40 mm for pipe entry of the box. Holes should be semi-shuttered type with 0.50 mm G P sheet made upper & lower cover duly screwed fitted with 300 mm round zink coted M.S. bar x 12 mm & brand name should be embossed. Fixing with wiring conduit laid in the R.C.C. roof before concreting along with supply of all material, labour, T&P etc. required for proper completion of work.

Supply and fixing of 100 Amp. Four pole Change over switch on 50 mm x 50 mm x 6 mm angle iron frame , including the cost of labour, T&P, painting and other material required for proper completion of the work as per direction and satisfaction of Engineer in charge.

Supply & Fixing of Fan Sheet of Backelite

S/F of LED Bulb 9 watt ISI

Supply & Fixing of light duties exhaust fan 12”dia ISI double ball bearing metalic Usha / Crompton/Bajaj make

Supply & Fixing of exhaust fan luvers 12”dia

S/f of ceiling fan 1200 mm sweep. Single star rated Usha / Crompton/Bajaj mak

S/F of Kit-Kat fuse 200 Amp with neutrail link ,wooden ply board ,Hole fasner with connection

S/F Required Lugs, Gland ect.

Please Enable Macros to View BoQ information