SPECIAL REPAIRS TO ROOF FLOORING, JOINERY, DOORS, WINDOWS, MOSQUITO WIRE MESH, INITERNAL WIRING, TOILET AND BATHROOM OF BLOCK NO P-74 AND P-75 AT MEANEE LINE, MEG AND CENTRE UNDER GE (NORTH) BANGALORE

Amount

Dismantling of Single Layer Mangalore pattern roofing tiling including ridges bedded in cement mortar etc complete all as specified and as directed.

Dismantling of Battern for tiles, shingles etc of any size including tilting fillets spaced exc 15 cm thick etc complete all as specified and as directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position as in Framed work etc complete all as specified and as directed.

Demolition of cement concrete and paving not exc 15 cm thick (below or above ground level) complete all as specified and as directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description & in any position not specifically provided for complete all as specified and as directed

Dismantling of stone slabs and tiles of any description or thickness in floors, appron, dado/Partitions laid bedded and pointed in any mortar etc complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises etc complete all as specified and as directed

Demolition of brick work /stone masonry/PCC block masonry built in cement mortar of any description all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from frames) not exc. 1.5 sqm each, including cutting holes for removing the hold fast etc (Distrubed surface of wall shall be make good by the contractor) complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutter from frames) exc. 1.5 Sqm but n exc 4 Sqm each, including cutting holes for removing the hold fast etc (Distrubed surface of wall shall be make good by the contractor)complete all as specified and as directed.

Taking down of 15 mm dia bore of steel tubing & connections including removal complete all as specified and as directed.

All as per item No 11 above but 20 mm dia bore and -ditto-

All as per item No 11 above but 25 mm dia bore and -ditto-

Taking down cement plaster of any description, hacking for key or raking out joint on old brick work/stone/concrete surface etc complete all as specified and as directed.

Dismantling of cast iron or reinforced concrete drain pipe up to 150 mm dia including fittings, jointed in cement mortar and taking out from trenches if required etc complete all as specified and directed.

Dismantling water tanks exc 500 litre but not exc 1000 litre and removing to store etc complete all as specified and as directed.

M&L for Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates confirming to Fe 410 -W (Gde- E- 250) quality-A etc including box section etc complete all as specified and as directed.

S&F Hollow /Solid steel section for structural use in beams, column, rafter purlins or other connecting plates including necessary welding, riveting, nut bolts as per IS-4923 etc complete all as specified and as directed

S&F Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick 150 AZ of any colour having tensile strength of 550 MPA as in roof covering/ cladding to wall, fixed with self tapping screws etc complete all as specified and as directed

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick 150 AZ of any colour having tensile strength of 550 MPA as in roof covering/cladding ridges under valley to wall, fixed with self tapping screws etc complete all as specified and as directed

M&L for 75 mm thick cement concrete type D- 2, (1:4:8) (40mm graded crushed stone aggregate) as in sub base of flooing etc complete all as specified and as directed.

M&L for cement concrete (1:2:4) type B-0 using 12.5 mm graded crushed stone aggregates) 25 mm thick as in sub base of flooring etc complete all as specified and as directed.

M&L for screed bed or bedding layer of mortar 15mm thick in CM (1:6) for laying floor finishes complete all as specified and as directed.

M & L for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and as directed.

M & L for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm,, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and as directed.

M&L for rendering 10 mm thick in cement mortar (1:3) on fair faces of brick work or concrete surface as backing coat coat of dado/skirting etc complete all as specified and as directed.

All as per item no 24 above but in skriting and -ditto-

M&L for Glazed ceramic coloured tiles 350X250X7mm / 450X350X7mm thick as in skirting / dado, set and jointed in neat cement slurry and pointed in white or colour cement to match etc complete all as specified and and as directed.

M&L for 18 to 20 mm thick Granite stone slab (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.including grinding the edges half round and polishing including etc complete all as specified and directed.

M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips etc complete all as specified and as directed.

All as per item No 31 above but 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders etc complete all as specified and as directed.

M&L for Pre-cast Cement concrete (1:3:6) type C1, using (20 mm graded crushed stone aggregates) with solid blocks, exc 10 cm in width and setting in CM (1:6) complete all as specified and directed.

M&L for Providing precast cement concrete (1:2:4) Type B-1 ( using 20 mm graded crushed stone aggregates) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in CM (1:6) etc complete all as specified and as directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for flat rough finished surfaces of concrete complete all as specified and directed.

M&L for RCC (Nominal mix) (1:1.5:3) type A-1,( using 20mm graded crushed stone aggregates) as in Beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and directed.

S&F Factory made 1.25 mm thick pressed steel frame of size 125 X 60 mm for door with one ore more rebate includings necessary fixing lugs, hinges, locks strike plate etc complete all as specified and as directed.

S&F Factory made 1.25 mm thick pressed steel frame of size 105 X 60 mm for door with one ore more rebate includings necessary fixing lugs, hinges, locks strike plate etc complete all as specified and as directed.

M&L for cement concrete (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) as in hold fast and filling of pressed steel chowkat etc complete all as specified and as directed.

M&L for Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290-0 or Fe -E-165 etc complete all as specified and as directed

S&F 35mm thick flush shutter solid core construction with decorative choice lamination both sides of shutter, kiln seasoned and chemically pressure treated complete all as specified and as directed

S&F factory made 2nd class 35 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges offraming plain, chamfered or rounded. fitted with cut and mitered beads for securing glass,\etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) etc complete all as specified and as directed.

S&F in repairs 18/19mm thick Block boards, grade 1 quality, exterior grade, commercial type, Water proof, termite proof, fixed with screws to timber frame-work as in cub board shutter, shelves etc complete all as specified and as directed.

M&L for 0.90 mm thick Decorative laminate type 1, of surface finish, colour and pattern as approved, fixed with approved adhesive as per maker's instructions, fixed to door/cub board shutter including teak wood beading 3mm thick and 18 mm wide including painting to match the existing colour etc complete all as specified and as directed.

S & F Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete as sepecified and directed (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life) complete all as specified and as directed.

S&F factory made solid PVC moulded door shutter with wood free EPS, 28 to 30mm thick (Stiles) with 2, 4 or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face and 2mm plain colour PVC sheet on back face etc. complete all as specified and as directed.

S&F Powder Coating (minimum thickness of powder coating 50 micron) aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete shall as specified and as directed.

S&F Powder Coating (minimum thickness of powder coating 50 micron) aluminium window and ventilator shutters, fixed / Sliding type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified complete all as specified etc. complete shall as specified and as directed.

S&F 4mm thick sheet glass of ordinary quality and glazing with oil putty or wooden beading to wooden frame or steel frame in squares n exc 0.50 sqm in each pane complete all as specified and as directed .

S&F 4mm thick sheet Figured glass, pin head type and glazing with oil putty in squares in exc 0.5 sq.m in each pane etcc omplete all as specified and as directed .

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainles steel wire stapel etc complete all as secified and as directed.

S&F Aluminium anodised tower bolt 200 mm long of extruded section etc complete all as specified and as directed.

S&F 100 mm thick butt hinges, heavy weight, stainless steel and fixed etc complete all as specified and as directed.

S&F 150 mm long aluminium handle, cast type, anodised etc complete all as specified and as directed.

S&F 150 mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor etc complete all as specified and as directed

S&F in repairs stainless steel decorative curtain rod of 25 mm bore with wood finishes (weight not less 400 gms per running meter) including fancy finale caps cap etc complete all as specified and as directed

S&F in repairs stainless steel Bracket for curtain rod of dia 25 mm dia made out of SS Flat not less than 20 mm wide 1.50 mm thick and overall length not less than 160 mm fixed with screws min 2 Nos with Rawl Plug of size not less than 50 mm long etc complete all as specified and as directed

S&F aluminium alloy, anodised sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy etc complete all as specified and as directed

S&F in repairs sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mmetc complete all as specified and as directed

S&F in repairs EWC (Ivory white) with normal closing seat cover of size 540X375X415mm with S Trap including connection to out going pipe, & seat cover and flushing pipe complete all as specified and as directed.

S&F in repairs white vitreous china wash basin Ivory white white flat back size 550x400 excluding taps but including 32 mm dia chromium plated aste fitting, PVC waste pipe 610 mm long and PVC connection 450 mm long complete all as specified and as directed.

S&F in repairs PVC deo flushing cisrern valveless with flushing out valve flushing cistern low level of 10 Ltr capacity white with inlet ball valve, float, flushing bend & handle including brackets & connection to pipe etc including PVC connection 450 mm long complete all as specified and as directed.

S&F in repairs bib cock long body with flange fancy type cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule or fixed for 15 mm dia bore pipe complete all as specified and as directed.

S&F in repairs 15mm bore Brass CP wall mixer with L Bend (with provision of hand shower) for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and directed.

S & F in repairs 15 mm bore central holes mixer w/o pop up waste system (9" spout) complete all as specified and as directed.

S&F in repairs angle cock with flange fancy type chromium plated brass cast copper alloy screwed down high pressure with crutch fixed for 15 mm dia bore pipe complete all as specified and as directed.

S & F PVC connection 15 mm size with PTMT nuts of length 450 mm, all as specified and as directed.

S&F in repairs full corner Glass Shelf (with brass brackets) etc complete all as specified and as directed.

S&F in repairs soap dish holder with glass etc complete all as specified and as directed .

S&F in repairs overhead round rain shower 8" Iwith out armns) of 15 mm bore dia etc complete all as specified and as directed.

S&F in repairs Hand shower (Health faucet) (ABS Body) with 8 mm dia, 1.20 mtr long flexible tube & wall hook etc complete all as specified and as directed.

S&F in repairs Jet spray suitable for EWC / Ango Indian EWC including fitting etc complete all as specified and as directed. .

S&F in repairs Stainless steel plate rack of size 990.60mm x 914.40mm including fixing to wall as directed etc complete all as specified and as directed

S&F in repairs SS Grab bar Towel rail 450 mm long incl fixing arrangement etc complete all as specified and as directed.

S & F 16mm dia CPVC pipes SDR 11 & Plain CI'VC SDR 11 fittings on walls/ ceiling or laying in floors incl cutting holes for concealing the pipes in stone / brick masonry complete all as specified.

All as per item No 75 above but 20 mm dia of bore pipe and -ditto-

All as per item No 75 above, but 25 mm dia of bore pipe and -ditto-

S&F rotational moulded PVC water storage tank 1000ltrs capacity conforming to IS-12701(1989) cylindrical vertical type double-layered with closed top including inlet,outlet and wash out holes of approved make hoisted and fixed in position etc complete all as specified and as directed.

S & F 25 mm dia of bore ball float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe complete all as specified and as directed [Minimum weight for 20 mm – 210 gms] .

S & F in repairs 25 mm gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and including taking down old gate valve all as specified and as directed.

S&F 110mm PVC, SWR pipes, single socketed in any length with rubber ring joint leaid in trenches or in floor complete all as specified and directed

Ditto- all as per item no.81 above but 75mm bore pipe complete all as specified and directed

S&F 110mm PVC, SWR pipes, single socketed in any length with rubber rings joint fixed with wall complete all as specified and directed

S&F PVC bends (any radius) of 110mm dia complete all as specified and directed

S&F PVC bends (any radius) of 75mm dia complete all as specified and directed

S&F PVC vent cowls of 110mm dia complete all as specified and directed

S&F in repairs 75 mm dia bore PVC (SWR) multi floor trap with grating including jointing with solvent cement etc complete all as specified and as directed

S&F in repairs for Grating doom 100 mm dia of PTMT (Minimum weight 25 gms) complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:6) on fair faces of brick work or concrete surface finsihed even and smooth (without using extra cement) etc complete all as specified and as directed.

M&L for rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surface finsihed even and smooth (without using extra cement) mixed with water proofing compound as per manufacture instruction etc complete all as specified and as directed.(Notes :WPC shall be measured and paid seperately)

M&L for cement concrete (1:2:4) type B1 using 20 mm graded crushed stone aggregates as in copings, Chajja kerbs, roof padding/staging of water tank etc including necessary formwork, weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.

Supply only water proofing compound (Liquid) complete all as specified and as directed.

M&L for 1mm thick wall care putty on wall including preparation of surface with sand paper etc to obtain smooth surface etc complete all as specified and as directed .

M&L for Preparing new plastered suface of walls and applying two coats Acrylic distemper, white or tinted over a coat of primer etc complete all as specified and as directed.

M&L for preparing newely plastered surface of wall and applying two coats of cement base paint etc complete all as specified and as directed

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed.

M&L for preparation of old painted surfaces of steel surface of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

S&F False ceiling with grid suspended system of size 600X600mm standard section consisting of main runner 29X24.70X0.80mm, cross Tee 29X24.70X0.80mm and wall angle 22.2 X22.2X0.65 mm, ceiling suspended with 3 mm dia GI wire hanger fixed with steel dash fastener, butter fly clips, hold down clips etc (Main corner, cross tee& wall angle of MS galvanized with PPPCGS) including 4 mm thick HPSC self textured design pre primered non asbestons fibre cement building boards fixed to false ceiling etc complete all as specified and as directed.

M&L for exterior grade, coloured glossy finish rubber pressed, cement concrete designer chequered tiles of size 30cm x 30cm x 25mm thick set, jointed and pointed in neat cement slurry with grey cement and pigment to match the shade / colour / matrix of tiles as in floor etc. complete all as specifed and as directed.

Taking down carefully aluminium/ copper wiring/power point wiring (light, fan, socket or power) complete including fittings such as switches ceiling roses, regulators, sockets light fittings, fans etc and making good the disturbed surface of walls, ceiling etc incl painting with same colour of the back ground complete all as specified and as directed by Engineer-in-Charge.

M & L Point Wiring (concealed) with 1.5 Sqmm single core PVC insulated unsheathed cable 1100 volts grade multi stranded with FRLS copper conductor conforming to IS 694 drawn through and including non-metalic rigid PVC conduit medium grade ISI marked incl accessories concelaed type wiring including GI branded sunken boxes suitable for modular concealed / surface type on walls including plastic/hylam laminated sheet top cover 3 mm thick/modular frame and cover of suitable module fixed with cadmium plated iron screws for housing modular/normal type switches, switch socket outlets, fan regulators etc., including provision of 1.5 Sqmm PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly, all as specified and as directed.for the following of :-

One light / fan/ Exhaust Fan point controlled by one switch

One light controlled by two way switch

One 3 pin socket out let 5 Amps on independent board

one 3 pin socket out let 5 A on same board

one Bell / Buzzer Point controlled by bell push

M & L Point Wiring (concealed) with 2.5 Sqmm single core PVC insulated unsheathed cable 1100 volts grade multi stranded with FRLS copper conductor conforming to IS 694 drawn through and incl non-metalic rigid PVC conduit medium grade ISI marked incl accessories concelaed type wiring incl GI branded sunken boxes suitable for modular concealed / surface type on walls including plastic/heylam laminated sheet top cover 3 mm thick/modular frame and cover of suitable module fixed with cadmium plated iron screws for housing modular/normal type switches, switch socket outlets, fan regulators etc., incl provision of 2.5 Sqmm PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly complete all as specified and as directed

Notes for Item No 101.1 to 101.5 & 102; Quoted rate is deemed to be included for the following:- (i) The earth wire for the points in the same circuit can be looped from point to point. (ii) Earth wire shall be taken inside the conduit. (iii) Cost of terminal box is deemed to be included in the item rate quoted for point wiring. (iv) Cost of a circuit of any length of cable from DB to any switch/ socket board to be included in point wiring. (v) Cost of cutting chases for conduits and making good to walls, in case of recessed or concealed conduit wiring will be included in point wiring.

S&F in replacement LED batten suitable for indoor applications 20 Watts, 4 feet with extruded aluminium housing & integrated LED channel complete with all accessories including taking out old fittings complete all as specified and directed. (Make: Bajaj, Cat No. BCLAB 20 W LED P S or equivalent Makes & model in Havells/Phillips/CG as per approved list and as approved by GE)

S&F in replacement LED batten suitable for indoor applications 10 Watts, 2 feet with extruded aluminium housing & integrated LED channel complete with all accessories including taking out old fittings complete all as specified and directed. (Make: Bajaj, Cat No. BCLSB 10 W WH or equivalent Makes & model in Havells/Phillips/CG as per approved list and as approved by GE)

S&F switch piano flush type single pole one way 5 Amps complete all as specified and as directed.

S&F switch socket combination 2 in 1, 3 pin 6 and 16 Amps flush type universal complete all as specified and as directed .

S&F switch piano flush type single pole two way 5 Amps complete all as specified and as directed.

S&F switch socket combination 5 pin 2 in 1, 5 A Flush type complete all as specified and as directed .

S&F stepped type electronic fan regulator flush switch type complete all as specified and as directed.

S&F Decorative, wall mounting ,champagne gold finish fixture with plastic body suitable for 9 watt LED lamp B22 base all as specified and directed .

S&F in repairs of bell push flush type 5A complete all as specified and as directed .

S&F in repairs of Ding Dong bell AC 230 volts single pole complete all as specified and as directed.

S&F in replacement of MCB SPN 240 volts 40 Amps complete all as specified and as directed.

S&F in replacement of MCB single pole 240 volts 10/16/20/32 Amps complete all as specified and as directed.

S&F in replacement of MCB DB SPN 12 way double door type 240 volts with 200 Amps rated busbar complete as specified and as directed.

S&F in replacement of MCB DB TPN 4 way double door type 240 volts with 200 Amps rated busbar complete all as specified and as directed.

S&F in replacement of MCB TPN 415 volts 10 KA 'C' 63 Amps complete all as specified and as directed.

S&F in replacement of ceiling rose, surface bakelite type 65 x 50 mm, 2 to 3 terminals complete all as specified and as directed.

Removing of old existing and M& L provision of new sub main wiring 1100 volts grade multistranded FRLS copper conductors, two runs of single core 2.5Sqmm along with 2.5 Sqm PVC insulated single core multistranded copper conductor cable as earth continuity conductor run along with suitable size of PVC conduit concealed type complete all as specified and as directed.

Removing of old existing and M& L for provision of new sub main wiring 1100 volts grade multistranded FRLS copper conductors, two runs of single core 6 Sqmm along with 6 Sqm PVC insulated single core multistranded copper conductor cable as earth continuity conductor run along with suitable size of PVC conduit concealed type all as specified and as directed.

Note for Item No 119 & 120 :-Quoted rate is deemed to be included for the following:- (i) 2 Runs of 2.5 Sqmm & 6 Sqmm cable and 1 run of 2.5 Sqmm & 6 Sqmm cable for earth continuity conductor along with PVC conduit will be measured as unit length. (ii) Cost of cutting chases for conduits and making good to walls, in case of recessed or concealed conduit wiring will be included in rate quoted in point wiring.

M&L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of earth plate at a depth not less than 1.5 mtr connected to galvanized earth lead wire 4 mm dia as earth lead up to 7.5 mtr long by means of nuts, bolts, thimbles,check nuts and washers etc made of galvanized iron connected to earthing test point all as shown in electrical plate No 3 of SSR Part-I 2010 and as specified or indicated and testing on completion incl earth work and excavation in any type of soil PCC (1:3:6) type C1 chamber, pre cost slab 40mm thick in cement concrete (1:2:4) type B1 with 8 mm dia MS bars reinforced at 10 cm centre to centre both ways incl funnel with watering pipe wire mesh and lugs, incl test point complete all as specified and as directed.

Supply and fixing 35 W LED bldg security light fitting with pressure die cast housing along with prismatic polycarbonate difuser with IP 66 protection including taking out old fittings.( Make:- Bajaj, Cat No.:- ENXT P 35L WH PO PC SD MT or Equivalent Makes & model as per approved list and as approved by GE)

S&F Storage type water heater 25 Ltrs BEE 5 star rated complete incl steel wired pipe for hot/cold water connection for inlet and out let water etc complete all as specified and directed.

S&F ceiling fans complete with complete accessories, 230V, SP 1200 mm Sweep with BEE 3 Star rating complete with all accessories and fixing the fan from ceiling rose with 3 core flexible copper wire 24/0.20 sqmm, etc all as specified and as directed .(Make Bajaj, SABSE TEZZ EE 03. Model No 251120 and equivalent on Havells/CG/ USHA as per approved list and as approved by GE)

S&F in replacement GI Bracket made out of GI tubing medium grade 25 mm bore , approx length 1.5 m long including MS clamps made out of MS flat iron 25 x 6 mm , nuts, bolts, washers etc and including before fixing applying two coats of aluminum paint over a coat of red oxide primer including removing the old existing GI bracket from bldg complete all as specified and directed.

Supply and fix in replacement exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete including necessary arrangement for installation complete all as specified and directed.

S&F in replacement LED lamp suitable to fit in angle holder of capacity 09 watt.( Make: Bajaj or eqv in Philips/Havells/CG as per approved list and as approved by GE).

M&L for core cutting in wall for fixing of exhaust fan and making good of distrubed wall/floor, painting of existing colour all as specified and directed .

Taking down ceiling fan, cable end, dismantling blades and removing fan and blades complete all as directed.

M&L for painting of celing fans complete, in situ with synthetic enamel pain by spraying incl filling cavities with filler,one coat after cleaning all dust etc. complete all as specified and directed.

S&F in replacement PVC Fresh air fan of 200 mm sweep 1200/1400 RPM with louver complete all as specified and as directed.

S&F Sheet metal enclosure single pole and neutral with a two pin and earth plug and socket with one single pole MCB 32 Amps, 230 Volts AC complete all as specifeid and directed.

ABHISHEK CONSTRUCTIONS (BID ID -3380689)

Sreyas Enterprises (BID ID -3379934)

MAA ENGINEERING SERVICERS (BID ID -3369203)