GE/PNH-13/2024-25

Amount

B/R PORTION: M&L for preparation of old plastered/ un-plastered wall surfaces including brooming down or steel wire brushing, scraping down, smoke soot, mould, moss, efflorescent salts, trading oil and greasy spots, and applying one coat of white wash on walls including cornices, pilasters etc, complete all as specified and directed.

M&L for complete removal of existing treatement and applying two coats of white wash on wall, complete all as specified and directed.

M&L for complete removal of existing treatement and applying one coat of colour wash on wall, complete all as specified and directed.

M&L for complete removal of existing treatement from wall plaster and applying one coat of oil bound distemper white or any tint, complete all as specified and directed.

M&L for complete removal of existing treatement from wall plaster and applying two coats of oil bound distemper white or any tint, complete all as specified and directed.

M&L for complete removal of existing treatement from wall plaster and applying one coat of cement base paint on wall or AC roof sheets complete all as specified and directed.

M&L for complete removal of existing treatement from wall plaster and applying two coats of cement base paint, complete all as specified and directed.

M&L for preparation of old painted wooden or wood based surfaces of any description not otherwise described, over 10cm width or girth including knotting and stopping as required and applying one coat of synthetic enamel paint, complete all as specified and directed.

M&L for preparation of old painted steel surfaces/CGI/PGI sheets of any description not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint in camouflage pattern, complete all as specified and directed.

M&L for applying wall care putty of approved make 3mm thick on walls as per manufacturer's instructions with and including rubbing by means of sand paper to have smooth finishing to receive primer / paint, complete all as specified and directed.

M&L for complete removal of existing treatement from wall plaster and applying one coat of weather proof water based exterior paint on walls, complete all as specified and directed.

M&L for writing letters or figures (Block, Roman, Italic or Indian) n. exc 30cm high with synthetic enamel paint including oblitering old writing of any description to match existing work, complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden / steel frames or stone/ concrete, glazed with putty or fixed with beads, complete all as specified and directed.

Taking up or down steel tubing of 15mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed.

Taking up or down steel tubing of 20mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed.

Dismantling PVC water tanks and removing to store of capacity not exceeding 500 ltr complete all as specified and directed.

Dismantling PVC water tanks and removing to store of capacity exceeding 500 ltr and not exceeding 1000 ltr complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

Dismantling of timber scantling 40sqcm and over in section, as in any position, complete all as specified and directed.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, complete all as specified and directed.

Taking down cement plaster of any description on stone or brick walls etc including racking out joints, hacking for key scrubbing down with water etc. complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and directed.

Dismantling floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) any thickness including cover fillets complete all as specified and directed.

Dismantling of timber scantling under 40sqcm in section unframed work as in fillets, rails, posts, rafters, purlins etc, complete all as specified and directed.

S&F 4 mm thick E-board (Classic) including fixing of frame work made up of special MS section, galvanized sheet with zinc coating cellular intro painting and consisting of angle cleats of size 25 mm wide, 1.6 mm thick with flag fixing to the ceiling with dash fastener 12.5 mm x 40 mm long or with 2 mm dia GI wire or fixed with bolts in GI channel main of size 35x25x0.5 mm thick and cross runner of size 25x25x0.5mm for fixing E-board of size 600x600mm x4 mm thick including fixing of E-board with ceiling section and perimeter of channel 25x25x1mm thick, 27mm high flange of 20mm to 30mm long extra including application of two coats of oil emulsion distemper, complete all as specified and directed.

All as per Srl item No. 27 Above but except ceiling frame and boarding, complete all as specified and directed.

S&F in repair 12mm thick both sides prelaminated particle board, medium density fixed with screw to frame work in cup board shutters, partitions, shelves etc acomplete all as specified and directed.

S&F 0.63mm thick galvanised corrugated mild steel sheeting with grade of Zinc coating of 275 gms/Sqm with two corrugation side lap and at least 150 mm end lap , fixed with L or J type or cranked hook bolts, in roof, walls etc, complete all as specified and directed.

All as per item No. 30 above, but except sheets, complete all as specified and directed.

S&F 0.80mm thick plain galvanised mild steel sheeting with 275 gm/sqm Zinc coating as in ridge , hips, valley gutters, drip and straight flashingfixed with L or J type or cranked hook bolts, in roof etc., complete all as specified and directed.

M&L for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F rolled mild steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connected plate confirming to Fe 410W(Gde E-250), quality 'A' complete all as specified and directed.

S&F mild steel work as in wind ties for roof including securing bolts, including all necessary drilling, bolting or riveting etc. and similar work conforming to Fe-250 Gde E-165 complete all as specified and directed.

S&F 2nd class soft wood (Kail) as in scantling, clean sawn timber fixed, complete all as specified and directed.

M&L for 50mm thick PCC 1:3:6 Type C-1 (using 20mm graded crushed stone aggregates) laid in alternate bays (not exceeding 2 sqm each) as in plinth protection, finished the surfaces even & fair, including filled the joints with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 (using 12.50mm graded crushed stone aggregate) as in sub base floor finishing surface even and fair, complete all as specified and directed.

M&L for cement concrete (1:2:4) type-B-1 (using 20mm graded stone crushed aggregate) as in lintels upto 1.5 metre clear span, cills, steps, siesmic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm height, copings, bed block, kneelers, apex stones, bed plates, roof kerbs round or chamfered on edges, water troughs and the like including weathering, slightly rounded or chamfered angles and throatings etc.including necessary form work complete all as specified and directed by Engineer-in-Charge.

M&L for Chequered cement concrete tiles 300x300x 25mm thick, set & jointed in neat cement slurry in floors and pointed with grey cement mixed with pigments, laid over and including 20mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for vitrified ceramic tiles, light shade, 10 mm thick (square/rectangular) area of each tile not exceeding 0.36sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shed of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

All as per ser item No.42 above but as in vertical surfaces of wall such as in dado/skirting etc. fixed over & including 10mm thick plaster in CM 1:4, complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shed of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

All as per ser item No.44 above but as in vertical surfaces of wall such as in dado/skirting etc. fixed over & including 10mm thick plaster in CM 1:4, complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exc 0.18 Sqm but n exc. 0.38 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

M&L for glazed ceramic coloured tiles (300x200mm) x 7mm thick, as in vertical surfaces such as in skirting and dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick back coat layer in cement mortar 1:4, complete all as specified and directed by Engr-In-Charge.

M&L for glazed ceramic coloured tiles (350x250mm) x 7mm thick / (450x350mm) x 7mm thickas in vertical surfaces such as in skirting and dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick back coat layer in cement mortar 1:4, complete all as specified and directed by Engr-In-Charge.

M&L for brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius, built in cement mortar (1:6), complete all as specified and directed.

M&L for walling of random rubble stone masonry brought upto course, well bonded, bedded and solidly hearted, built in cement mortar (1:6), complete all as specified and directed.

All as per item No. 50 above, but except stone complete all as specified and directed

Extra over stone walling of random rubble walling, uncoursed or brought for hammer dressing with maximum depression on face from straight edge held against the dressed surface not exceeding 20mm to face stones (lime and sand stone) and dressing of face beds and joints, complete all as specified and directed.

M&L for 15mm thick cement plaster rendering in CM 1:4 on fair faces of bricks or concrete surfaces, chajja and suspended work, or stone surfaces finishing the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:6 on other than fair faces of brick or stone masonry wall surfaces & finishing the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for preparation of newly plastered or unplastered surfaces of wall and applying two coats of cement base paint, complete all as specified and directed.

M&L for preparation of newly plastered surface of wall including cornices pilaster etc, and applying two coats of oil emulsion distemper over and including 1 mm thick wall care putty, complete all as specified and directed.

Taking down shutters of any description exc 1 sqm but not exceeding 2sqm each, complete all as specified and directed.

Taking down shutters of any description not exceeding 1sqm each, complete all as specified and directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.5 Sqm each, complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5 Sqm and not exceeding 4Sqm each, complete all as specified and directed.

S&F 2nd class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

S&F 35mm thick 2nd class hard wood plain, framed, panelled door shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of 12mm thick veneered particle board medium density, wood particle board with commercial face veneers, complete all as specified and directed.

S&F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc divided into square (with sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) supplied and fitted to chowkats complete all as specified and directed.

S&F 30mm thick 2nd classhard wood glazed and skeleton shutters, for window/ventilators, open rebated and prepared to receive glass, gauge etc divided into square (with sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (b) supplied and fitted to chowkats complete all as specified and directed.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm prelam PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with prelam sheet, reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed.

S&F factory made solid PVC moulded door shutter with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam (Nut brown colour) PVC Sheet on the front face & 2mm prelam (Nut brown colour) PVC Sheet on back face, supplying & fixing in frame at site complete all as specified and directed. Note:- Cadmium screws to be used for fixing and fixtures of fittings.

S&F in repair door closer hydraulically regulated, designation No.3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

S&F in repair Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified.

S&F in repair anodised aluminium window/ventilator shutter fixed type shutters, with or without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc., complete all as specified and directed.

S&F in repair Anodised aluminium partition door, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified.

S & F for pressed steel frames 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed.

S & F for pressed steel frames 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed.

S&F mild steel butt hinges, medium weight, cold rolled,100mm long, complete all as specified and directed.

S&F mild steel butt hinges, medium weight, cold rolled,75mm long, complete all as specified and directed.

S&F aluminium anodised, barrel tower bolts of extruded section of size 150mm and fixed, complete all as specified and directed.

S&F aluminium anodised, barrel tower bolts of extruded section of size 100mm and fixed, complete all as specified and directed.

S&F aluminium alloy handles, cast type, anodised of size 150mm and fixed, complete all as specified and directed.

S&F aluminium alloy handles, cast type, anodised of size 100mm and fixed, complete all as specified and directed.

S&F 250mm long aluminium alloy anodized sliding door with haps, staple (bolt type) and fixing clips of sheets, cast or extrusted sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beading, complete all as specified and directed.

S&F 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint of Ist quality over a coat of pink primer, complete all as specified and directed.

S&F sheet glass ordinary quality, 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane, complete all as specified and directed.

S&F figured glass pin headed type, 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint of Ist quality over a coat of red oxide primer to new or previously untreated steel surfaces over 10cm width or girth including preparation of surfaces, complete all as specified and as directed.

S&F in repair MS powder coated tubular curtain rod fancy type of 25mm dia complete all as specified and directed.

S&F in repair MS powder coated decorative type bracket, end ball, rounded block, bracket (coated with brown/cherry/golden colour) suitable for 25mm dia curtain rod of approved pattern and shade fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screw complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type-C1 (using 20mm graded crushed stone aggregate) as in copings, hold fasts plinth band, bed blocks and like slightly rounded or chamfered angles as directed including necessary form work, complete all as specified and directed.

S&F steel water tubing of 15 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified and directed.

S&F steel water tubing of 20 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified and directed.

S&F in repair bib tap 15 mm bore with flange, Brass CP, fancy type. with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair angular stop valves cast copper alloy 15 mm dia, chromium plated with wall flange screwed down, high pressure, with capstan handle screwed both ends for iron pipes or for unions complete all as specified and directed.

S&F in repair vitreous china squatting pan (Orissa pattern) size 580 x 440 mm, snow white, with 'P' or 's' trap, front or back inlet and integral foot rests, complete connection to drain (outgoing pipe) and to flushing pipe and syphonage pipe etc. including lime concrete

S&F in repair PVC valve less syphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC. flush pipe for low level cistern including all joints, complete all as specified and directed.

S&F in repair vitreous china wash hand basin, white, flat back, size 550x400 mm excluding taps, waste, chain & plug and porcelain stopper but including brass chromium plated waste coupling, and waste pipe PVC 32mm dia including cutting for and pinning in ends of brackets or erecting stand etc complete all as specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts on both ends of length 450mm complete all as specified and directed.

S&F in repair 15mm bore pillar tap cast copper alloy with capstan head, fancy type, chromium plated, screwed down, high pressure, with or without lettered 'Hot or Cold' with long screwed for iron pipe complete all as specified and directed.

S&F in repair 32mm dia PVC corrugated waste pipe with union 800mm long complete all as specified and directed.

S&F in repair PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint to walls as soil pipe with & including clamps, complete all as specified and directed.

S&F in repair PVC (SWR) pipes 75mm dia any length single socketed with rubber ring joint to walls as soil pipe with & including clamps, complete all as specified and directed.

S&F in repair vitreous china urinals, bowl type of size 465x355x265 mm (minimum) white with grating and union for discharge pipe (excluding flushing cistern and waste pipe),complete including poviding and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing with automatic flushing cistern with brackets, flush pipe, waste pipe grating and union for discharge pipe complete all as specified and directed.

S&F in repair grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms), suitable for floor taps, complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I, of capacity 500 Ltrs incl with 20mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I, of capacity 1000 Ltrs incl with 20mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F in repair chromium plated hand shower (Health faucet) with 1.5m long flexible tube of stainless steel in chrome finish and wall hook complete all as specified and directed.

S&F in repair CP jet spray with holder including 1.5m long PVC/Chromium plated flexible PVC pipe, necessary nut bolts and PVC washers fixed with PVC seat cover for pedestal pattern water closet, complete all as specified and directed.

S&F in repair plastic water closet seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised or PVC hinging device complete all as specified and directed.

S&F in repair PVC water tank cover suitable for 500ltrs/1000ltrs water tank, complete all as specified and directed.

Cleaning / disinfecting of PVC / RCC water storage tank of any capacity with disinfecting chemicals (Chlorine) properly with water thoroughly flushed out, complete all as specified and directed.

Taking down existing roof treatment of any description in any condition including removing of cement plaster of concrete of any description from the roof surfaces and removing all the debris to a distance n.exc 100m and roughening surfaces by sweeping clean and washing down with water to remove dust etc and applying evenly cement slurry at the rate of 3 Kg/Sqm over cleaned surfaces and providing 10 mm thick cement screed in CM 1:4 , finished surface even and smooth, after that cleaning the entire roof surface thoroughly to remove all loose particles, dust/dirt particles and applying with one coat of industrial bituminious primer at the rate of 0.40 lit/Sqm over the plastered surfaces of roof and applying a course of a coat of binding material with blown type bitumen of grade 85/25 heating to working temperature of 180 0 C @ 1.2 kg/sqm then applying APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3 mm thick reinforced with polyster non wove fabric (wt not less than 150 gms/sqm) laid with 75 mm side overlap and 150 mm overlap primed surfaces by forced (tourch) application as per manufactures instructions and applying two coats of aluminium paint over APP membrane, complete all as specified and directed.

Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight), complete all as specified and directed.

Welded steel wire fabric supplied and fixed complete to wood or steel members, complete all as specified and directed.

S&F Vitreous china wash down water closet pan (pedestal pattern) white, (excluding fixing bolts, fluhing cistern and flush pipe), complete connection to drain (outgoing pipe) and to flushing pipe and anti syphonage pipe etc with & including fixing bolts fixed in repair, complete all as specified and directed.

S&Fin repair insulated PVC wall lining/panelling, complete all as specified and directed.

E&M PORTION:- Excavation in trenches n. exc. 1.5 mtr in wide and n. exc. 1.5 mtr in depth for laying of underground cable and getting out in any type of soil complete all as specified and directed.

Excavation in trenches not exc. 1.5 m wide and exc. 1.5m but not exc 3.0 m in depth for foundation of poles, stay assembly etc and getting out in hard/ dense soil complete all as specified and directed.

Returning, filling in surplus spoil including spreading, leveling, watering and well ramming in layers n. exc. 25 cm thick complete all as specified and directed.

Removing of excavted soil to a distance n. exc. 50 mtr and deposited where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

M&L for Sand cushioning to under ground cable providing with a layer of Sand 08 cm thick before laying of cable and 15 cm after laying of cable in trenches, hand punning complete all as specified and directed by Engr-in-charge (Note : Punning thickness of 18 cm will be measured for payment purpose)

M&L for Burnt bricks locally available, sub class 'B', laid flat for protection of under ground cable complete all as specified and directed at site.

Supply, laying , jointing and testing in repair of cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminum conductor of size 120 sqmm 3.5 core, laid in trenches/ducts or fixed to poles/walls or laid under roads/paths/drains/culverts including cable gland of suitable sizes and aluminium lugs for connection, complete all as specified and directed. Make: Finolex / KEI Industries Pvt Ltd / Polycab / Gloster / Universal Cables. Note: Excavation, earthwork, sand cushioning, brick protection shall be measured & paid for separately.

All as per Item No 123 above but size 3.5 core 95 sqmm complete all as specified and directed.

All as per Item No 123 above but size 3.5 core 70 sqmm complete all as specified and directed.

All as per Item No 123 above but size 3.5 core 50 sqmm complete all as specified and directed.

All as per Item No 123 above but size 3.5 core 35 sqmm complete all as specified and directed.

All as per Item No 123 above but size 3.5 core 25 sqmm complete all as specified and directed.

All as per Item No 123 above but size 4 core 16 Sqmm complete all as specified and directed.

All as per Item No 123 above but size 2 core 10 sqmm complete all as specified and directed.

All as per Item No 123 above but size 2 core 6 sqmm complete all as specified and directed.

Supply and fix aluminium thimbles suitable for 95 sqmm XLPE cable complete all as specified and directed.

Supply and fix aluminium thimbles suitable for 120 sqmm XLPE cable complete all as specified and directed.

Supplying, installation and erection in true vertical position steel tubular swaged welded pole, 9.0 metre long, conforming to IS-2713 part-II, type 410 SP-31, complete with cast iron/MS base plate 6mm thick and of size 300x300mm, finial taper, pole cap, bolts, nuts, washers & screws etc., pole made out of ERW Mild steel tubing tubing including holes of required Nos and size for fixing of cross arms, painting with one coat of red oxide primer and two coats of aluminium paint on exposed surfaces and two coats of black bituminous paint for portion embedded in concrete, painting three signal red colour bands at lower portion of exposed pole starting from plinth block , each band of 300mm height at 300mm spacing, painting pole No with black paint by stenciled letters/figures of 8cm height, including taking down old pole any type complete all as specified and directed. Note: Excavation, earth work and PCC in foundation of poles, coping etc shall be measured and paid separately in respected items.

Supply, stringing, stretching and binding in replacement with insulator, ACSR conductor of adequate size (Weasel /ferret/Mink) on LT Poles including providing of necessary jumpers, connecting all existing incoming and out going connections, trimming of trees approximately 2 mtr around conductor etc complete all as specified and directed.

Stringing only, ACSR conductor including providing of suitable binding wire for connecting the existing OH lines and providing of necessary jumpers, connecting all existing incoming and outgoing connections, trimming of trees, trimming of trees approximately 2 mtr around conductor etc complete all as specified and directed.

S&F in replacement Cradle hexagonal , rectangular fabricated with GI wire 4 mm dia on existing OH line, complete all as specified and directed.

Supply, stretching and binding in repair GI earth wire 4 mm dia on existing OH line complete all as specified and directed.

M&L for replacement of Cross arms, bracings, supports,clamps and back plates fabricated from structural steel sections including bolts,washers, welding , bending cold or hot, drilling holes for bolts,in any shape or sizes as indicated or directed and inclusive of one primer coat and two coats of alluminium paint complete all as specified and directed.

S&F in repair Pin type insulator Porcelain, vitreous white/ brown/ green insulator including one galvanized mild steel spindle, two galvanized iron washers and one galvanized iron nut, 100 mm height, 65 mm dia for 1100 volt grade, complete all as specified and directed.

S&F in repair disc type insulator Porcelain, vitreous white/ brown/ green insulator including one galvanized mild steel spindle, two galvanized iron washers and one galvanized iron nut, 100 mm height, 65 mm dia for 1100 volt grade, complete all as specified and directed.

S&F in replacement Shackle type porcelain , vitreous white, brown or green insulator including galvanised mild steel straps, wahsers, insulator bolts, wahsers and nuts, as working pressure 1100 volts height in 100 mm maximum dia 115 mm section of straps in 31 x 5 mm dia of bolts 14 mm complete all as specified and directed.

S&F in repair Stay assembly comprising of MS stay plate of size 30cmx30cmx6mm thick, stay rod with nuts 215cm long, 20mm dia, MS/GI stay bow 40 cm length with 2 Nos GI thimbles, galvanized stay wire standard size 7/4mm, loop insulation size 90mmx65mm clearance of hole 16 mm & other accessories all as per SSR Part-1, Plate No.1 including necessary MS clamps, excavation earth work & PCC work complete all as specified and directed.

S&F in repair Tubing 'light grade' galvanised iron with all fittings and fixed to poles, walls etc. with flat iron clamps/bolts/nuts/washers or laid in floors/under roads complete of size 80 mm bore, complete all as specified and directed.

Cutting through existing bituminous road /PCC/floor/approx size width 15cm X 60cm depth along cross section of the road for laying of GI tubing/RCC pipe for encasing of cable and repairing the road to match with the original finish complete all as specified and directed.

M&L for Plain cement concrete (1:4:8) Type D-2 (using 40mm graded crushed stone aggregates) as in foundation for steel tubular poles including necessary form work and finishing the exposed surface even and smooth with out using extra cement complete all as specified and directed.

M&L for Plain cement concrete (1:2:4) Type B-1 using 20 mm graded crushed stone aggregates, as in coping of steel tubular poles foundation for steel tubular poles including necessary form work and finishing the exposed surface even and smooth with out using extra cement complete all as specified and directed.

Supply and fixing line separator with high quality PVC suitable for LT 1100 volts 4 lane OH aluminium conductor complete all as specified and directed.

Supply and fixing line separator with high quality PVC suitable for LT 1100 volts 2 lane OH aluminium conductor complete all as specified and directed.

M&L for Painting of LT panel including preparation of old surfaces by scrapping old paint completely and applying two coats of super enameled paint over a coat of red oxide primer complete all as specified and directed.

M&L for Painting to steel poles including cross arms, 'V' brackets, 'D' clamps, nuts, bolts, complete including painting with five strips of 30cm each with black and white paint in alternate strips from the base of pole upto 1.5mtr height complete, spray painting with two coat of synthetic enamel paint of first quality silver paint over a coat of red oxide primer after and including complete removal of old paint by scratching, rubbing complete all as specified and directed.

All as per Srl item No. 151 Above but two pole structure steel/RCC with cross arms, clamps, structure etc 1.1 KV complete all as specified and directed.

All as per Srl item No. 151 Above but four pole structure steel/RCC with cross arms, clamps, structure etc 1.1/11 KV, HT/LT complete all as specified and directed. Note for Srl item No. 35 to 38: Each job included scraping out, worn out old paint and making surface smooth suitable for application of paint

M&L for spreading evenly stone aggregate of size 40 mm in the sub station area complete all as specified and directed.

S&F in repair MCCB, 4 pole, 100 Amps, 415 volts, adjustable type with breaking capacity 16 KA Ics=75% Icu, complete all as specified and directed.

S&F in repair MCCB, 4 pole, 160 Amps, 415 volts, adjustable type with breaking capacity 36 KA Ics=100% Icu, complete all as specified and directed.

S&F in repair MCCB, 4 pole, 200 Amps, 415 volts, adjustable type with breaking capacity 36 KA Ics=100% Icu, complete all as specified and directed.

S&F in repair MCCB, 4 pole, 250 Amps, 415 volts, adjustable type with breaking capacity 36 KA Ics=100% Icu, complete all as specified and directed.

S&F in repair MCCB, 4 pole, 400 Amps, 415 volts, adjustable type with breaking capacity 36 KA Ics=100% Icu, complete all as specified and directed.

Supply, fixing, testing & commissioning of LT bus bar chamber box, platform mounted, suitable for 3 phase, 4 wire, 415 volts, 50 Hz AC supply and having 400 amps MCCB 36 KA, 4 pole for incoming and four Nos stepped type aluminium bus bar 200A for looping & branch connection system, the chamber shall be painted with powder coated paint , bus bar chamber shall be provided with suitable neoprene rubber gasket to make it completely dust and vermin proof and degree of protection not less than IP-55, bus bar chamber shall be made out of 3.15 mm thick CRCA mild steel sheet, front door (01 layer) and rear door (01 layer) opening facility and side slanting canopy type roof on top and angle iron padestal frame including PCC work, 0.6 Mtr above ground level, grouting etc including provision of suitable size of cable glands, cable lugs,nut, bolts,washers etc. (The bottom portion of enclosure shall be minimum 60 cm above ground level of legs of angle iron), including taking down old bus bar chamber box, complete all as specified and directed.

S&F in repair 1100 Volts grade heavy duty cable PVC insulated aluminum solid conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4 mm suspension wire, one twin core cable flat or circular, size of aluminum conductor 6 sq mm, complete all as specified and directed. Make : Finolex / KEI Industries Pvt Ltd / Polycab / Gloster / Universal Cables.

All as per Srl item No. 163 Above but of size 10 Sqmm complete all as specified and directed.

S&F in repair Earthing complete with galvanized steel plate electrode 600 mm x 600 mm x 6.0 mm thick, burried directly in ground vertically in pit of depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below normal ground level surrounded from all sides with mixture of charcoal and common salt in alternate layers and electrode connected to galvanized iron strip 32 x 6 mm size by means of GI bolts, nuts, check nuts and washers, earth strip protected by galvanized steel pipe 40 mm bore (light grade) connected to main switch board or any other electrical equipment all as shown in electrical plate No. 3 of SSR-2009 Part I and including necessary excavation and earth work in any type of soil, 20 mm bore medium grade GI pipe for watering, funnel with wire mesh, PCC (1:3:6), type C-1 chamber, RCC (1:2:4), type B-1, reinforced with 8 mm dia TMT bars @ 15 cm c/c both way for cover and MS frame etc., complete all as specified and directed. NOTE: The unit rate includes earth strip and protection pipe upto (maximum 7.5 metre from earth plate) earth point/test point.

S&F in repair Earthing complete with galvanized steel plate electrode 600 mm x 600 mm x 6.0 mm thick, burried directly in ground vertically in pit of depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below normal ground level surrounded from all sides with mixture of charcoal and common salt in alternate layers and electrode connected to galvanized iron wire 4 mm dia by means of GI bolts, nuts, check nuts and washers, earth wire protected by galvanized iron pipe 15 mm bore (light grade) connected to main switch board or any other electrical equipment all as shown in electrical plate No. 3 of SSR-2009 Part I and including necessary excavation and earth work in any type of soil, 20 mm bore medium grade GI pipe for watering, funnel with wire mesh, PCC (1:3:6), type C-1 chamber, RCC (1:2:4), type B-1, reinforced with 8 mm dia TMT bars @ 15 cm c/c both way for cover and MS frame etc., complete all as specified and directed. NOTE: The unit rate includes earth wire and protection pipe upto (maximum 7.5 metre from earth plate) earth point/test point.

S&F in repair Single pointed air termination Aluminium rod 12mm dia, 300 mm long complete all as specified and directed.

S&F in repair Test point terminal block made of gun metal or phosphorous bronze of size 75x75 x 25mm drilled and screwed including 3 Nos 8mm dia 25mm long hexagonal head brass screws including box of size 90 x 90 x 90mm made of 1.6mm plain sheet and screwed to GI pipe/ wall for protection of test point complete all as specified and directed.

S&F in repair earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 32 x 6 mm galvanised iron strip, complete all as specified and directed.

S&F in repair aluminium strip 25 x 3.15mm with saddles and fixing screws, insulators rawl plugs etc for conductor for roof and fixed on wall upto test point, complete all as specified and directed.

S&F in repair rubber insulating mat of size 2mx1mx12mm thick, ISI marked, complete all as specified and directed.

Supply and fix aluminium thimbles suitable for 50 sqmm XLPE cable complete all as specified and directed.

Supply and fix aluminium thimbles suitable for 35 sqmm XLPE cable complete all as specified and directed.

Supply and fix aluminium thimbles suitable for 25 sqmm XLPE cable complete all as specified and directed.

Supply only tape insulation 20mm x 25 mtrs, complete all as specified and directed.

M/S MANHAS ENTERPRISES

narayan construction

M/S KHAN ENTERPRISES

JAMWAL CONSTRUCTION CO

VIKAS ENTERPRISES