ADDN/ALTN/IMP TO CERTAIN MD ACCN AT AF STN JALAHALLI (PHASE V) BANGALORE

Amount

Schedule 'A' Part - I (B/R ITEMS):- Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thick above or below ground level complete all as specified and as directed.

Dismantling floor hearth / wall tiling including cement mortar bedding, removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Demolition of reinforced cement concrete in floors, beams, chajjas, landing slab in any position or height and similar suspended works complete all as specified and as directed.

Demolition of brick work or stone masonry built in cement mortar or cement lime mortar including all quoins, arches etc complete all as specified and as directed.

Taking down cement plaster from old walls of any description and raking out joints, hacking for key, scrubbing down with water built in cement mortar complete all as specified and as directed.

Taking down cement plaster from ceiling surfaces built in cement mortar complete all as specified and as directed.

Taking down chowkhat or frames not exceeding 1.5 Sqm each with shutters (Without taking off shutters from the frames complete all as specified and as directed.

Taking down chowkhat or frames exceeding 1.5 Sqm but not exceeding 4 sqm each with shutters (without taking off shutters from the frames) complete all as specified and as directed.

Taking down shutters of any description exceeding 1Sqm and not exceeding 2 Sqm each complete all as specified and as directed.

Material and labour for providing plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and as directed.

Material and labour for providing 75mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in floors, paving finished fair and even complete all as specified and as directed.

Material and labour for providing 25mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in flooring finished fair and even without using extra cement complete all as specified and as directed.

Material and labour for providing 25mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as padding for roof surfaces, finished even and smooth complete all as specified and as directed.

Material and labour for providing cement concrete 1:2:4 type B1 using 20mm graded stone aggregate in coping, bed blocks and similar work, weathering, slightly rounded or chamfered angles and throating including necessary form work complete all as specified and as directed.

Material and labour for providing 75mm thick cement concrete 1:3:6 type C-2, using 40mm graded stone aggregates as in plinth protection finished fair and even complete all as specified and as directed.

Material and labour for providing reinforced cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in slabs and finishing exposed surfaces fair & even complete all as specified and as directed. Note: Reinforcement and formwork shall be measured and paid separately.

Material and labour for providing reinforced cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in chajjas and finishing exposed surfaces fair & even complete all as specified and as directed. Note: Reinforcement and formwork shall be measured and paid separately.

Material and labour for Pre-cast reinforced cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate set in cement mortar 1:4 as in cover slab including all necessary form work. Exposed surfaces of concrete shall be finished even and smooth without using extra cement complete all as specified and as directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips and all as specified and directed.

Mild steel TMT bars 8mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips and all as specified and directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

Use and waste of formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and as directed.

Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exceeding 10cm but not exceeding 20cm wide complete all as specified and as directed.

Material and labour for brick work with sub class 'B' bricks straight or curved on plan exceeding 6.00m mean radius built in cement mortar 1:6 and all as specified and as directed.

Material and labour for taking down of existing sunken slab treatment from the sunken portion and removing of existing filling of sunken, cleaning the surfaces washing down with water and rubbish off the premises, cleaning and filling cracks with sealing compound, brushing neat cement [email protected]/sqm and providing 25mm thick cement concrete type B-0 (1:2:4) (using 12.5mm graded stone aggregate) on sunken slab portion.. (b) Material and labour for two coat of acrylic cementitious water proofing coating (Dr FIXIT pidfin 2K manufactured by M/S Pidilite industries Ltd or equivalent approved) and followed by a overlay protective rendering 15mm thick CM (1:3) alongwith liquid water proofing compound approved make and including filling of brick bats and finishing the top surfaces even and smooth without using extra cement .(c) sunken slab after preparation as mentioned above method of application for acrylic cementitious water proofing coating is followed as per manufactures instruction complete all as specified and as directed.

BLANK

Material and labour for rendering 10mm thick in CM 1:4 on fair faces of brick work or concrete surfaces as in backing coat to receive wall tiles etc complete all as specified and as directed.

Material and labour for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished even and smooth using water proofing compound all as per manufactures instruction complete all as specified and as directed. Note: Water proofing compound shall be measured and paid separately.

Material and labour for rendering 10mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished fair and even using integral water proofing compound all as per manufactures instruction complete all as specified and as directed. Note: Water proofing compound shall be measured and paid separately.

Material and labour for rendering 10mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished fair and even complete all as specified and as directed.

Material and labour for rendering 5mm thick in CM 1:3 on ceiling on fair faces of concrete surface, even and smooth without using extra cement complete all as specified and as directed.

Material and labour for 15mm thick screed bed in CM 1:6 for laying floor finishes complete all as specified and as directed.

Material and labour for 20mm thick screed bed in CM 1:6 for laying floor finishes complete all as specified and as directed.

Material and labour for non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

Material and labour for laying Glazed ceramic tiles in vertical surface 350mmx 250mmx 7 mm/ 450mmX 350mmX 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and as directed.

Material and labour for laying Non skid joint free ceramic coloured tiles 7 to 8mm thick, area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

Material and labour for Non skid joint free ceramic coloured tiles 7 to 8mm thick , area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm in skirtings, dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

Material and labour for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including treating the surface with beeswax polish complete all as specified and as directed.

Material and labour for Kota stone slab 20-25mm thick in riser of steps, skirting, dado etc laid over cement screed and jointed with neat cement slurry and pointed in white or coloured cement to match including treating the surface with beeswax polish complete all as specified and as directed.

Material and labour for keyed pointed in CM 1:4 for squared rubble masonry complete all as specified and as directed.

Supply only integral water proofing compound ISI marked .

Material and labour for providing granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed.

Hacking out old broken glass of any thickness / size or description from metal frames fixed with glass putty complete all as specified and as directed.

Material and labour for providing 4mm thick sheet glass, ordinary quality and glazing with oil putty with spring clips in metal frames in square not exceeding 0.5 sqm each panes complete all as specified and as directed.

Material and labour for 2nd class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and as directed.

Supply and fix 35 mm thick 2nd class hardwood plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated board medium density, wood particle board with commercial face veneers complete all as specified and as directed.

Supply and fix 2nd class hardwood 35mm thick glazed and skeleton shutters open rebated and prepared to receive glass gauze etc divided into squares, with plain, chamfered or rounded mitred and rebated sash bars any number edges of framing plain, chamfered or rounded, fitted with cut and metered beads for securing glass etc size of members of shutters as specified in SSR Part I Sec 8 clause 8.24 (a) complete all as specified and as directed.

Supply and fix PVC hollow door frame of size 50mm x 47mm with a wall thickness of 5mm made out of extruded 5mm thick rigid PVC foam sheet, mitre cut at two corners and joined with two nos of 150mm long brackets of 15mm x 15mm MS square tube. The two vertical door profiles are to be reinforced with 19mm x 19mm MS square tube of 19 gauge, EPDM rubber gasket, weather seal to be provided through out the frame. The doorframe shall be fixed to the wall using 65/100mm long MS screws through the frame using PVC fasteners. A minimum of four nos of screws to be provided for each vertical member and minimum of two nos of screws for each horizontal member complete as per Manufacturer’s specification complete all as specified and as directed.

Supply and fix factory made solid PVC moulded door shutter 28 to 30 mm thick(stiles), with 2,4 or 6 raised panel board core design with 5mm thick moulded PVC sheet on front face & 5mm thick plain coloured PVC sheet on back face complete all as specified and as directed.

Taking down steel window/ventilators area not exceeding 1.5 sqm each including all fittings complete all as specified and as directed.

Supply and fix steel Window/ ventilators with top hung shutter including hinges, steel peg stay etc complete all as specified and as directed.

Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed.

Dismantling of boarding, any description, fixed in any position with nails (in floor etc) complete all as specified and as directed.

Supply and fix 18/19 mm thick Block boards, grade 2 quality interior grade commercial type, fixed with screws to timber frame work complete all as specified and as directed.

Supply and fix 30 mm width of flap Continuous (Piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and as directed.

Supply and fix 40mm dia, mild steel cupboard knobs fixed with nut, screw and washer complete all as specified and as directed.

Supply and fix mild steel hasp and staple, 125mm safety type with mild steel hinge pin including bolt type complete all as specified and as directed.

Supply and fix 140mm ball catches with 8 mm dia steel ball, and brass body and striking plate including letting in complete all as specified and as directed.

Supply and fix mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

Material and labour for mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and as directed.

Supply and fix Stainless Steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with stainless steel wire staples complete all as specified and as directed.

Supply and fix 2nd class hardwood small fitting such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like including all necessary labours, articles of size not exceeding 200Cucm each complete all as specified and as directed.

Supply and fix 150 mm Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

Supply and fix 200 mm Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

Supply and fix 300 mm mild steel sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy and fixed complete all as specified and as directed.

Supply and fix in repair mild steel 300 mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

Supply and fix 150 mm Aluminium handles, cast type, anodised complete all as specified and as directed.

Supply and fix 100 mm Aluminium handles, cast type, anodised complete all as specified and as directed.

Supply and fix 125 size Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and as directed.

Supply and fix 100 mm size Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and as directed.

Supply and fix 50mm size Butt hinges, medium weight, cold rolled mild steel and fixed complete all as specified and as directed.

Material and labour for mild steel powder coated pelmet rods 25mm outer dia including 2 Nos of brackets 2 Nos of pintals or side brackets as per site requirement including 10 Nos of curtain rings in each curtain rod complete all as specified and directed.

Supply and fix 150mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and as directed.

Taking down cement plaster including water proofing treatment any type from roof top complete all as specified and as directed.

Material and labour for screed bed of mortar 15 mm thick in cement mortar 1:4 with WPC over cleaned concrete surfaces complete all as specified and as directed. Note: WPC shall be measured and paid separately.

Material and labour for water proofing treatment on horizontal and vertical surface with polymeric water proofing membrane at the rate of 4Kg/Sqm reinforced with min160 gram/Sqm non woven polyster mat over a coat of bitumen primer @0.20 Ltr/Sqm and a coat of hot blown bitumen of 85/25 or 95/15 @ 1.20 Kg/Sqm applied on the top of Polymeric membrane and finally finished with a coat of bituminous aluminium paint @ of 100 grams/Sqm all specified and directed and testing complete all as specified and as directed.

Taking up or down steel tubing 15mm bore and connection including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down steel tubing 20mm bore and connection including cleaning for refixing or removal to store complete all as specified and as directed.

Supply and fix 15mm dia steel tubes medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor including making hole in RCC slabs for vertical pipes & making good the same with cement concrete 1:2:4 complete all as specified and as directed.

Supply and fix 20mm dia steel tubes medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor including making hole in RCC slabs for vertical pipes & making good the same with Cement Concrete 1:2:4 complete all as specified and as directed.

Refixing 15mm dia old steel tubing and connection in new or old position (wall ceiling floor etc including cutting altering the size or changing the new fittings etc complete all as specified and as directed.

Refixing 20mm dia old steel tubing and connection in new or old position (wall ceiling floor etc including cutting altering the size or changing the new fittings etc complete all as specified and as directed.

Dismantling of cast iron / RCC/ PVC drain pipes jointed in cement mortar and taking out from trenches or walls of any bore including fittings complete all as specified and as directed.

Supply and fix in repairs PVC (SWR) floor trap 75mm dia of outlet, plain with grating including jointing with solvent cement fixed complete all as specified and as directed.

Supply and fix PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls bore of pipe 110 mm with PVC clamps.

Supply and fix 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in under floors complete all as specified and as directed.

Supply and fix 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with PVC clamps complete all as specified and as directed.

Supply and fix 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints in under floors complete all as specified and as directed.

Supply and fix 110 mm bore PVC (SWR) bends of any radius with access door complete all as specified and as directed.

Supply and fix 75mm bore PVC (SWR) bends of any radius with access door complete all as specified and as directed.

Supply and fix 110 mm bore PVC (SWR) reducers complete all as specified and as directed.

Supply and fix 110 mm bore PVC (SWR) couplers complete all as specified and as directed.

Supply and fix 75 mm bore PVC (SWR) couplers complete all as specified and as directed.

Supply and fix 110mm bore PVC (SWR) junction single(single T) equal or unequal with access door complete all as specified and as directed.

Supply and fix 75mm bore PVC (SWR) junction single(single T) equal or unequal with access door complete all as specified and as directed.

Supply and fix 110mm bore PVC (SWR) vent cowl complete all as specified and as directed.

Supply and fix 125/110 mm size PVC (SWR) gully trap setting and jointing with solvent, cement complete all as specified and as directed.

Supply and fix 125/110mm dia PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and as directed.

Supply and fix in repairs sink with drainage board made of stainless steel 1mm thick with plugs, washer and wastes including fixing in cement mortar 1:3 to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size 915x460mm, bowl size 410 mix 330 mix 160 mm including CP waste coupling 40mm complete all as specified and as directed.

Supply and fix Stainless steel Plate rack 900mm x 600 mm x 200mm deep with plate racks, spoon holders, shelves etc complete all as specified and as directed.

Supply and fix in repair Vitreous china squatting pan "Orissa pattern" size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) complete including provn of lime concrete bedding and making good to floor complete all as specified and as directed.

Supply and fix in repair vitreous china white wash hand basin flat back size 550x400mm 'including CI/MS brackets including cutting for and pinning in brackets but excluding waste pipe complete all as specified and as directed.

Supply and fix in repairs 10 ltrs capacity PVC valve less syphonic action type flushing cistern low level with inlet ball valve float and handle complete all as specified and as directed.

Supply and fix in repairs for 15mm dia of pipe bib taps cast copper alloy, fancy type, chromium plated with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

Supply and fix in repairs for 15mm dia of pipe stop valve, fancy type and chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for Unions and fixed complete all as specified and as directed.

Supply and fix in repairs for 15mm dia of pipe angle valve, fancy type and chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for Unions and fixed complete all as specified and as directed.

Supply and fix 25 mm dia gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

Supply and fix PTMT shelf with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 300 gms) complete all as specified and as directed.

Supply and fix 15 mm dia brass chromium plated pillar taps with capstan heads, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipes complete all as specified and as directed.

Supply and fix in repairs PVC connection 15mm dia and 45cm long with two nos of brass check nuts and washers complete all as specified and as directed.

Supply and fix in repairs brass Chromium plated shower rose with or without swivel joints 125mm size including fixing to steel pipe or union complete all as specified and as directed.

Supply and fix grating doom 125mm dia with waste hole of PTMT (Min wt 40 gms) complete all as specified and as directed.

Supply and fix 32 mm dia waste coupling of PTMT (half or full threaded) complete all as specified and as directed.

Supply and fix PVC waste pipe 32 mm dia flexible with cup & pressure rating 6 kgf/cm2 to fit wash hand basin waste coupling complete all as specified and directed by Engr-in-Charge.

Supply and fix soap-dish PTMT with multiple boxes all as specified and directed by Engr-in-charge

Supply and fix in repairs 600mm long tubular tower rail brass chromium plated 20mm dia, D type 60cm long fixed with two plugs (Gutties) of 2nd class hard wood embedded in cement mortar 1:3 with MS screws complete all as specified.

Supply and fix in repair Rotational moulded Polyethylene water storage tank - 500 liters capacity (cylindrical vertical with closed top) hoisted and fixed in position including PTMT float valve 25mm dia complete all as specified and as directed.

Material and labour for preparation of new surfaces of wall including scrapping down, smoke soot, efflorescentg salts trading oil and greasy spots etc by applying three coats of white wash on walls complete all as specified and as directed.

Material and labour for preparation of old surfaces of ceiling including scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc (Plastered or unplastered surfaces) and applying a coat of white (lime) wash complete all as specified and as directed.

Material and labour for preparation of new plastered surfaces of ceiling including scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc and applying three coats of white (lime) wash complete all as specified and as directed.

Material and labour for preparation of old painted wood and wood based surfaces of any description not otherwise described over 10 cm width or girth and applying a coat of synthetic enamel paint in any tint complete all as specified and as directed.

Material and labour for preparation of new wood and wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink wood primer complete all as specified and as directed.

Material and labour for distempering walls with two coats of washable distemper oil emulsion on new plastered wall surfaces (white or tinted) as directed after washing/rubbing down and stopping of distempered and painted surfaces as in preparatory work to give uniform and smooth finish all as specified and as directed. Note: First coat of distempering on new surfaces of walls with washable distemper emulsion shall be carried out as specified in SSR part I and final coat of distempering walls with washable distemper oil emulsion shall be carried out through mechanical tools.

Material and labour for distempering walls with a coat of washable distemper oil emulsion on old plastered wall surfaces (white or tinted) as directed after washing/rubbing down and stopping of distempered and painted surfaces as in preparatory work to give uniform and smooth finish all as specified and as directed. Note: Distempering with washable distemper oil emulsion on old wall surfaces shall be carried out through mechanical tools

Material and labour for preparation of new steel surface and iron work of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Material and labour for preparation of old steel surface and iron work of any description over 10cm width or girth not otherwise described and applying a coat of synthetic enamel paint complete all as specified and as directed.

Material and labour for preparation of new plastered surface of walls including cornices, pilasters etc and applying two coats of cement base paint complete all as specified and as directed. Note: First coat of cement base paint on new surfaces of wall shall be carried out as specified in SSR Part I and final coat of cement base paint on walls shall be carried out through mechanical tools.

Material and labour for preparation of old decorated surfaces of walls including cornices, pilasters etc (Plastered or un plastered surfaces) and applying one coat of cement base paint complete all as specified and as directed. Note: One coat of cement base paint on old wall surface shall be carried through mechanical tools.

Resecuring or easing and adjusting wooden shutters of any description exceeding 1Sqm and not exceeding 2Sqm each with taking out and re-fixing in same opening complete all as specified and directed by Engr-in-charge.

Supply and fix in repair stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed.

Material and labour for forming Construction joint 30mm deep x 10mm wide filled with sealing compound, Grade'A' all as directed.

Supply and fix 8 feet 4 pipes pulley operated cloths drying system consisting of aluminium pipe of outer dia 22mm, inner dia 19.80mm, made up of detrin with rope guide mounted on channel pair of length 24 feet (distance between two pipes is adjustable) locking system to hide rope knot, channel to be mounted or fixed with self taping screws provided in kit. Rope will be HDPE double core of 4mm dia fixing to ceiling as specified and directed by Engr-in-Charge and minimum weight of one pipe shall not be less than 0.20kg/, minimum weight of rope shall not be less than 7700Gms/unit complete all as directed.

Removing building materials etc to a distance of 500m or under, beyond the lead included in the rates, including loading, unloading and stacking at the destination complete all as directed by Engineer in charge.

Supply and fix 4mm thick frosted glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane and all as specified and as directed.

Material and labour for injecting chemical emulsion using chlorpyriphos 20 percent EC with 1 percent concentration for post constructional Anti-termite treatment along external wall below concrete or masonry apron using chemical emulsion at the rate of 2.25 liters per linear metre including drilling and plugging holes etc in apron complete all as specified and as directed.

Material and labour for injecting chemical emulsion using chlorpyriphos 20 percent EC with 1 percent concentration for post constructional Anti-termite treatment for treatment of soil under existing floors using emulsion at the rate of one liter per hole, 300mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor complete all as specified and as directed.

Material and labour for injecting chemical emulsion using chlorpyriphos 20 percent EC with 1 percent concentration for post constructional Anti-termite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) at the rate of 0.50 liter per hole by drilling 6mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same complete all as specified and as directed.

Making arrangement of scaffolding in buildings, cutting of small trees/plants at the stem, removal of the roots of the plants by using acids, cutting around the spot for removing the roots any size and making good with cement mortar 1:3 or with PCC 1:2:4 including finishing with existing complete all as directed by Engineer-in-charge.

Racking out joints / points in cement mortar to squared rubber masonry coursed or uncoursed complete all as specified and as directed.

Writing letter or figures (Block, Roman, Italian or Indian) not exceeding 30cm high including preparation of base surface any colour as approved complete all as specified and as directed.

Schedule 'A' Part - I (E/M ITEMS):- Point wiring complete with 1. 5 Sq mm single Core PVC insulated FRLS cable, 1100 volts grade unsheathed with multi stranded copper conductor drawn through and including PVC rigid non metallic conduit with all fittings such as bend, end caps etc fixed on the surface of wall, ceiling, roof, steel structure etc. by means of suitable fixing accessories including provision of 1.5 Sq mm single core PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor for earth continuity conductor, including provision of metal flush box duly sunkened with modular white cover plate with frame of suitable size for mounting and housing the modular switches, sockets, regulators etc. all as specified and as directed complete for One light point controlled by one way switch. Note:- (i) The rates are deemed to be included cutting chasing of any description of wall and making good the disturbed surface. (ii) Modular white cover plate and frame shall be measured and paid seperately

All as per item No. 143 here- in - before but for one ceiling fan point controlled by one way switch.

All as per item No. 143 here- in - before but for one exhaust fan point controlled by one way switch.

All as per item No. 143 here -in - before but for One 2/3 pin switch socket point controlled by 5 Amps switch on Independent board

All as per item No. 143 here -in - before but for One 3 pin switch socket outlet combination, 15 Amps, independent, with cables 2.5 sq mm

Taking down carefully copper/aluminum point wiring (light, fan, Power) complete fittings such as switches, ceiling roses pendants, regulators sockets light fittings etc removing to store for keeping in safe custody or for taking credit and making good disturbed surface of wall, floors, roof etc all as specified.

Material and labour for point wiring with two runs of FRLS PVC insulated unsheathed, 1100 V grade cable multi stranded copper conductor of size 1.5 sqmm drawing through in and including PVC conduit size of not less than 20mm on surface including provn of metal flush box duly sunkened with modular white cover plate with frame of suitable size for mounting modular switch, socket and regulator along with earth wire of PVC insulated, unsheathed, 1100 V grade cable multi stranded copper conductor of size 1.5 sqmm all as specified and directed for One light point controlled by one switch one way 6 Amps all as specified and directed. Note : (i) Cost of cutting chasing, sunken in the wall for box and making good to disturbed surface all as to match with existing surface are deemed to be included in quoted rate. (ii) Modular white cover plate and frame shall be measured and paid seperately

All as per item No 149 but for One ceiling fan point controlled by one switch one way 5 Amps

All as per item No. 149 here -in - before but for One 2/3 pin switch socket point controlled by 5 Amps switch on Independent board.

All as per item No 149 but for One socket out let 5 Amps 3 pin on same board.

All as per item No. 149 here -in - before but for One light point controlled by two, two way switches.

All as per item No. 149 here -in - before but for One 3 pin switch socket outlet combination, 15 Amps, independent with cables 4 sq mm

All as per item No 149 but for One bell point controlled by one switch one way 5 Amps bell push

Supply and fix modular switch single pole one way 6 Amps 1 module complete all as specified and directed

Supply and fix modular switch single pole two way 6 Amps 1 module complete all as specified and directed.

Supply and fix modular bell push switch single pole one way 6 Amps 1 module complete all as specified and directed.

Supply and fix modular socket outlet, multipurpose 2 in 1 , 3 pin 5 Amps, flush type universal all as specified and as directed.

Supply and fix modular socket outlet, multipurpose 2 in 1 , 3 pin 5 Amps / 16Amps flush type universal all as specified and as directed.

Supply and fix ceiling fan Modular type regulator step type 120 watt 2 module complete all as specified and directed.

Supply and fix Buzzer, Ding Dong AC. 230 volts, single pole complete all as specified and directed.

Supply and fix Lamp holder, PVC / Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

Supply and fix ceiling rose, surface Bakelite type, PVC, 65 x 50 mm isolated body with three terminals all as specified and as directed.

Supply and fix in repairs 4 ft LED batten, wattage 18 w, having minimum lumen out put 1880 to 2000 with a system efficiency 100 lumen/watt short circuit and voltage cut of protection and wide operating voltage range - 140V to 270 V 6500 K colour temps, 50000 hrs life, IP 20 with all accessories internally Pre wired and including connecting up with 3 core flexible copper conductor cable 0.75 sq mm from ceiling rose to fitting, mounted on roof/wall etc. on PVC round bush of suitable approved size all as specified and as directed. MAKE: BAJAJ Item Code 830192 LED Batten 18 W CDL or equivalent approved make listed in PS.

Supply and fix in repairs 2 ft LED batten, wattage <10 w, having minimum lumen out put >900lm with specially designed extructed thermal polycarbonate housing with high optically efficient serrated diffuse, isolated multistage CCCV driver with operating voltage range-140V to 270V temp range 0 to 50 deg C, driver efficiency >85%, power factor >0.95, THD<10% colour temp 6500 K, surge protection- 3KV in CM, safety extra low voltage safe level<60V DC as per IEC strandard, IP 20 protection, life of 50000 hrs with luminaries efficiency > 100lm/W including connecting up with flexible copper conductor cable 1.5 sq mm size from ceiling rose to connector fitting, mounted on roof/wall etc. on PVC round bush of suitable approved size all as specified and directed. MAKE: BAJAJ Item Code 830206 LED Batten 10 w CDL Plastic or equivalent approved make listed in PS.

Supply and fix LED Bulb 9W Item code 830213, product LEDZ bulb 9W CDL B22 of Make Bajaj or equivalent approved make listed in PS

Provision of LED building security/street light fitting 20 watts made up of pressure die cast housing with toughened glass diffuser, with high power LEDs with option of secondary optic with IP66 protection, 110 LM/ watt and wired with accessories alongwith suitable bracket & clamps with bolts & nuts including taking down old light fitting complete all as specified and directed. Make: Crompton, ASTRA NEO Product Description LSTS-20-CDL-M or equivalent approved make listed in PS.

Remove and refix existing serviceable ceiling fans 1200/1400 mm sweep servicing, painting and writing MES No. of ceiling fan with one coat of synthetic enamel paint by spraying including greasing/oiling, filling cavities with filler after cleaning all dust etc. complete all as specified and as directed by Engineer-in-Charge.

Supply and fix ceiling fan, complete with three blade, down rod, accessories 230V, 1200mm sweep, with Squirrel cage induction motor complete all as specified and as directed by Engineer-in-Charge.

Supply and fix Exhaust fan 300 mm sweep metal body, 230/240 volt AC single phase 410W, 1400 RPM, including core cutting hole on stone masonry (Machine cutting) suitable for fixing exhaust fan with suitable nuts bolts and louvers and make good the surface to match with existing surface complete all as specified and directed by Engr-In-Charge.

Supply and fix Exhaust fan 250 mm sweep PVC body, 230/240 volt AC single phase 410W, 1400 RPM, including core cutting hole on stone masonry (Machine cutting) suitable for fixing exhaust fan with suitable nuts bolts and louvers and make good the surface to match with existing surface complete all as specified and directed by Engr-In-Charge..

Supply installation, testing and commissioning of Water heater storage type, capacity 25 litre BEE 5 star rated, electrically operated, single phase, 230V, 50Hz with vent pipe, fusible plug, thermostat, safety valve, proper earth connector, SS tank complete with all accessories required for plumbing work, grouting bolts and nuts etc, including inlet & outlet pipe connection(CP), one NRV, one bib tap and one stop cock complete all as specified and as directed by Engineer-in-Charge.

Material and labour for sub main wiring with 2 single core stranded copper conductor unsheathed PVC insulated cable 1100V grade, 10 Sqmm drawn through suitable size of non-metallic PVC rigid conduit with 1x10 sqmm copper conductor cable as earth conductor and conduit accessories fixed up in surface/recessed as required, connection up and taking down old wiring complete all as specified and directed.

Supply and fix in repairs MCB DB SPN 8 way, horizontal, double door, 240 V, AC, 50 Hz, for MCB DP as incomer and SP MCBs as out going, IP- 43 protection confirming to IS-13032, universal mounting with copper bus bar, neutral link, earth link, earthing shuds detachable gland plates with knockouts on both sides complete all as per specified.

Supply and fix in repairs MCB single pole and neutral 240 volts 40 Amps, 10 KA rupturing capacity, C series complete all as specified and as directed.

Supply and fix in repairs MCB single pole 240 volts 5 to 30 Amps, 10 KA rupturing capacity, C series complete all as specified and as directed.

Dismantling of unserviceable existing panel board and making good surface as per existing complete all as specified and directed by Engr-In-Charge.

Dismantling the existing electric meter carefully, from power supply of incoming and out going PVC cable and keeping in safe custody including recording down the Sl No, meter reading, and Qtr No/ circuit No to the meter and refixing the same complete all as specified and directed.

Supply, installation, testing and commissioning of factory made meter panel board wall mounted made out of CRCA sheet of 2mm thick indoor type totally enclosed weather proof, dust vermin proof with front openable, hinged door locking arrangement mounted on MS clamp welded to panel body duly grouted in wall including provn of Acriylic sheet for meter reading, space for refixing of single phase KWH meter 5-60 Amps -05 Nos AC 230Volts including lugs, spacer mounting channels, rubber gasket, locking knobs, PVC shrinkable sleeves, nut bolts, washers etc, suitable compartment of every meter and control MCB circuit and epoxy powder coated spray paint with primer, CPRI type tested complete all as directed including the following accessories:- Incoming (a) MCCB 63amps 04 pole, 415 Volts, 16 KA - 01 No (b) R-Y-B phase LED indicating lamp-03 Nos (c) Copper wiring in panel of suitable size (d) 200 Amps TPN copper busbar Out going (a) MCB 32 - 40 amps SPN, 230 Volts, 10 KA -06Nos (b) MCB SPN 10Amps, 230Volts, 10KA-01 No (c) Re-fixing existing electric meter - 07Nos (Note: To be ensured properly matching the qtr Nos before fixing the electric meter)

Material and labour for Earthing complete with galvanised iron earth plate electrode 60cm×60cm×6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion including excavation/ earth work in any type of strata, removal of surplus excavated material, GI pipe for watering and funnel, PCC 1:3:6 type C1 chamber with RCC 1:2:4 type B1 including 6mm dia TMT bars as reinforcement in cover slab with GI protection pipe complete all as specified including testing on completion and taking down old earthing material.

Supply and fix modular switch 01 way 16A, 01 module complete all as specified and as directed.

Supply and fix white cover plate with frame, 01 module complete all as specified and as directed.

Supply and fix white cover plate with frame, 03 module complete all as specified and as directed.

Supply and fix white cover plate with frame, 06 module complete all as specified and as directed.

Phoenix Infra

UNITED TECHNO PROJECTS PVT LTD

SIGNATURE INFRASTRUCTURES(E DHARANI KUMAR REDDY)

K. VENKATESH NAIDU