RENOVATION OF WASH ROOMS IN FACTORY AREA AND RENOVATION OF WASH ROOMS KITCHEN AND DINING HALL IN CISF AREA

Amount

CARRIAGE OF MATERIALS up to 01 km By Mechanical Transport including loading, unloading and stacking

Lime, moorum, building rubbish, demolishaed material etctc

Earth

Earth work in excavation by mechanical means (Hydraulic excavator) / manualmeans in foundation trenches or drains (not exceeding 1.5 m in width or 10sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5m, including dressing of sides and ramming of bottoms, lift upto 1.5 m,including getting out the excavated soil and disposal of surplus excavated soilas directed, within a lead of 50 m. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides offoundations etc. in layers not exceeding 20cm in depth, consolidating eachdeposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sand under floors, including watering,ramming, consolidating and dressing complete

Surface dressing of the ground including removing vegetation and inequalitiesnot exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade excludingthe cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20mm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofshaving slope up to 15° landings, balconies, shelves, chajjas, lintels,bands, plain window sills, staircases and spiral stair cases above plinthlevel up to floor five level, excluding the cost of centering, shuttering,finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for all heights :

Foundations, footings, bases of columns, etc. for mass concrete

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Reinforcement for RCC work ( Tor or Mild ) including bending, binding,straightening and placing in position complete (Tor / Mild steel will besuppliedby NFL free of cost).

Brick work with common burnt clay F.P.S. (non modular) bricks of classdesignation 7.5 in superstructure above plinth level up to floor V level in allshapes and sizes in : cement mortar 1:4 (1 cement : 4 course sand)

12 mm cement plaster of mix : in 1:4 (1 cement: 4 fine sand)

Demolishing cement concrete manually/ by mechanical means includingdisposal of material within 50 metres lead as per direction of Engineer - in -charge. Nominal concrete 1:3:6 or richer mix

Demolishing R.C.C. work manually/ by mechanical means including stackingof steel bars and disposal of unserviceable material with in 50 metres lead asper direction of Engineer - in- charge.

Extra for cutting reinforcement bars mannually / by Mechanical means inR.C.C. or R.B. work(Payment shall be made on the cross sectional area ofR.C.C. or R.B. work).As per Direction of Engineer in Charge

Demolishing brick work manually/ by mechanical means including stacking ofserviceable material and disposal of unserviceable material within 50 metreslead as per direction of Engineer-in-charge.

Dismantling doors, windows and clerestory windows (steel or wood) shutterincluding chowkhats, architrave, holdfasts etc. complete and stacking within50 metres lead

Dismantling tile work in floors, walls and roofs laid in cement mortarincluding stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm

Dismantling C.I. or asbestos or PVC rain water pipe with fittings and clampsincluding stacking the material within 50 metres lead : 75 mm or more Dia(open Surface)

Dismantling G.I. pipes (external work) including excavation and refillingtrenches after taking out the pipes, manually/ by mechanical means includingstacking of pipes within 50 metres lead as per direction of Engineer-in-charge: 15 mm to 40 mm nominal bore

Dismantling C.I. / PVC / Asbestos Pipe including excavation and refillingtrenches after taking out the pipes, manually/ by mechanical means breakinglead caulked joints, melting of lead and making into blocks including stacking ofpipes & lead at site within 50 metre lead as per direction ofEngineer-in-charge: up to 150mm diameter (inside wall / floor)

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) includingstacking of useful materials near the site and disposal of unserviceablematerials within 50 metres lead.

Dismantling old plaster or skirting raking out joints and cleaning the surface forplaster including disposal of rubbish to the dumping ground within 50 metreslead.

Dismantling W.C. of all sizes including disposal of dismantled materials i/cmalba all complete as per directions of Engineer-in- Charge.

Hacking of CC flooring including cleaning for surface etc. complete as perdirection of the Engineer-in-Charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushingcistern, including flush pipe, with manually controlled device (handle lever),PVC Connection pipe with brass union conforming to IS : 7231, with all fittingsand fixtures complete, including cutting and making good the walls and floorswherever required: - White Vitreous china Orissa pattern W.C. pan of size580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet (Europeantype W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern,including flush pipe, with manually controlled device (handle lever), CIbrackets, Brass union PVC pipe, conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floorswherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing 8 mm dia Stainless Steel Jet with flexible tube upto 1metre long with S.S. triangular plate to Eureopean type W.C. of quality andmake as approved by Engineer - in - charge.

Providing and fixing white vitreous china extended wall mounting water closetof size 780x370x690 mm of approved shape including providing & fixing whitevitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre(adjustable to 4 litre/ 8 litres), both Jet & Hand Faucet, cistern fittings, nuts, ragbolts, fixing of joints and required fittings including seat cover, and gasket etcwhatever required complete as per direction of Engineer-in- charge.

Providing and fixing white vitreous china flat back half stall urinal of size580x380x350 mm with fittings, standard size C.P. brass flush pipe, spreaderswith unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556,C.I. trap, PTMT urinal cock with outlet grating and other couplings in C.P.brass, including painting of fittings and cutting and making good the walls andfloors wherever required :Single half stall urinal

Providing and fixing wash basin with C.I. brackets, 15 mm PTMT pillar cock, 32mm PTMT waste coupling of standard pattern, including painting of fittings andbrackets, cutting and making good the walls wherever required. White VitreousChina Flat back wash basin size 550x400 mm or more.

Providing and fixing/placing wash basin with C.I. brackets, 15 mm dia CPBrass single hole basin mixer of approved quality and make, PVC Connectionsincluding painting of fittings and brackets, cutting and making good the wallswherever required:- White Vitreous China Wash basin size 550x400 mm with a CP Brasswaste Coupling,15 mm CP Brass basin mixer of required shape and Size(Table Top wash basin of required Size with necessary fixing arrangements )

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality &make and as per the direction of Engineerin- charge.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C.waste fittings complete.-: Semi rigid pipe 32 mm dia

Providing and fixing 600x450 mm beveled edge mirror of superior glass (ofapproved quality) complete with 6 mm thick hard board ground fixed to woodencleats with C.P. brass screws and washers complete

Providing and fixing mirror of superior glass (of approved quality) and ofrequired shape and size with Bevelled Edged of approved make and shadewith 6 mm thick hard board backing fixed with SS brackets :Rectangular shape 1500x450 mm

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm highand 112 mm distance from wall of standard shape with bracket of the samematerials with snap fittings of approved quality and colour, weighing not lessthan 105 gms.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mmwide with minimum distances of 37 mm from wall face with concealed fittingsarrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing gun metal gate valve with C.I. wheel of approvedquality (screwed end) : 25 mm nominal bore.

Providing and fixing ball valve (brass) of approved quality, High or lowpressure, with plastic floats complete :

15 mm nominal bore

25 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality(screwed end) : 25 mm nominal bore

Horizontal

Vertical

Providing and placing on terrace (at all floor levels) polyethylene water storagetank, IS : 12701 marked, with cover and suitable locking arrangement andmaking necessary holes for inlet, outlet and overflow pipes but without fittingsand the base support for tank.: Circular Tank

Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour.

15 mm nominal bore, weighing not less than 32 gms

25mm nominal bore, weighing not less than 62 gms

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth102mm, height of 75mm with concealed fitting arrangements, weighing not lessthan 106 gms.

Providing and fixing PTMT bib cock of approved quality and colour. 15 mmnominal bore, 165 mm long, weighing not less than 110 gms

Providing and fixing PTMT stop cock of approved quality and colour:Concealed stop cock 15 mm nominal bore, 108 mm long, weighing not lessthan 108 gms

Providing and fixing PTMT angle stop cock 15 mm nominal bore, weighing notless than 85 gms

Providing and fixing PTMT grating of approved quality and colour-

125 mmnominal dia with 25 mm waste hole

Rectangular type with openable circular lid -150 mm nominal size square 100mm diameter of the inner hinged round grating

Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighingnot less than 40 gms

Providing & fixing uplasticised PVC connection pipe with brass unions :15 mmnominal bore with 45 cm length

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, havingthermal stability for hot & cold water supply, including all CPVC plain & brassthreaded fittings (Socket, Reducer(of required dia at site), nipple, Cap, plug,Reducer -Tee, Elbow(bend), Tee, Union, Cross Tee, Coupler) i/c fixing thepipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittingswith one step CPVC solvent cement and the cost of cutting chases and makinggood the same including testing of joints complete as per direction of Engineerin Charge.Concealed work, including cutting chases and making good the walls etc.

20 mm nominal bore.

25 mm nominal bore.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, havingthermal stability for hot & cold water supply, including all CPVC plain & brassthreaded fittings (Socket, Reducer(of required dia at site), nipple, Cap, plug,Reducer -Tee, Elbow(bend), Tee, Union, Cross Tee, Coupler) i/c fixing thepipe with clamps at required spacing. This includes jointing of pipes & fittingswith one step CPVC solvent cement including testing of joints complete as perdirection of Engineer in Charge. (exposed on wall at all locations)

20 mm noninal outer dia pipe

25 mm noninal outer dia pipe

Providing and fixing C.P. brass long body bib cock of approved qualityconforming to IS standards and weighing not less than 690 gms.15 mm nominal bore-

Providing and fixing required Stainless Steel Fitting of press fit design ofgrade AISI 304 conforming to JWWA G116 standard with V-profile orM-profile and with O-ring sealing gasket of EPDM material of required diaas per direction of Engineer-in-charge. - Coupling/ SocketFor 15.88 mm outer dia

Providing and fixing C.P. brass stop cock (concealed) of standard designand of approved make conforming to IS:8931. :-15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser pointsof approved quality conforming to IS:8931. :- 15mm nominal bore

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand :4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix(1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size),inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarsesand) finished with floating coat of neat cement and making channels incement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate20 mm nominal size) finished with a floating coat of neat cement complete asper standard design :Inside size 90x80cm and 45cm deep including C.I. cover with frame (mediumduty) 455 x 610 mm mm internal diamensions total weight of cover and frameto be not less than 38kg (weight of cover 23 kg and weight of frame 15 kg.With common burnt clay FPS(non modular) bricks of class designation 7.5

Providing & fixing square mouth S.W. gully trap class SP -1 complete with C.I.Grating brick masonry chamber with water tight CI cover with frameof 300X300mm size (inside) the weight of cover to be not less than 4.50kg and frame to benot less than 2.70 kg as per standard design180x 150 mm size P Type with Common burnt clay FPS( Non Modular ) bricksof class designation 7.5

Cleaning and desilting of gully trap chamber, including removal of rubbishmixed with earth etc. and disposal of same, all as per the direction ofEngineer-in-charge.

Providing and fixing 18 mm thick gang saw cut, mirror polished, pre-mouldedand prepolished, machine cut for kitchen platforms, vanity counters,doors/window sills, steps, skirtings, floor, facias and similar locations ofrequired size, approved shade, colour and texture laid over 20 mm or morethick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated withwhite cement, mixed with matching pigment, epoxy , including rubbing, curing,Moulding and Polishing of edges (visible faces) to give high gloss finish etc.complete at all levels.Granite of any colour and shade decided by NFL Engineer - Area of slab0.50 sqm or any area

Extra for Fixing, Moulding and Polishing of edges (front and side faces) togive high gloss to marble /granite stone, over and above correspondingbasic item, in facia, nosing and drops of width upto 150 mm with epoxyresin based adhesive, including cleaning etc. complete.

Providing and fixing Ist quality ceramic glazed wall tiles (Rectified) conformingto IS: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades including highlighter tile(s) as required of any sizeas approved by Engineer-in-Charge, in skirting, risers of steps and dados,over 12 mm or more thick bed of cement mortar 1:3 (1 cement : 3 coarsesand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointingin white cement mixed with pigment of matching shade complete. Size : 300x600 mm

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved make, in all colours, design, pattern, finish and shades laid over floor, steps, skirting etc. laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete (Anti-Skid, Anti-Static Doubly Charged Vitrified Tile of Any Colour and Size decided by NFL Engineer) Size of Tile: 400x400 or 500x500 or 600x300 or 300x300 mm

Providing and fixing on wall face unplasticised - Rigid PVC rain waterpipesconforming to IS:13592 Type A including jointing with sealring andChemical solvent , fixing the pipe with clamps conforming to IS : 5382leaving 10mm gap for thermal expansion.

Single socketed pipes- 75 mm diameter

Single socketed pipes- 110 mm diameter

Providing and fixing on wall face unplasticised PVC moulded fittings/accessoriess for unplasticised Rigid PVC rain water pipes conforming toIS: 13592 Type- A including jointing with seal ring conforming to IS:5382leaving 10 mm gap for thermal expansion.

Coupler 110mm

Bend 87.5 degree 110mm bend

Shoe(Plain) 110mm shoe

Single Tee / Y-Bend with Door 110 x 110 x 110 mm

Single Tee / Y-Bend without Door 110 x 110 x 110 mm

Coupler 75 mm

Single Tee / Y-Bend without door 75 x 75 x 75 mm

Single Tee / Y-Bend with door 75 x 75 x 75 mm

Bend 87.5 degreee 75 mm bend

Shoe(Plain) 75 mm shoe

Execution of any job non-susceptible to measurement which includes all minor consumable material, tools and tackles and the payment shall be onbasis of working hours (Major consumable / material shallbe supplied by NFLand the decision of the Engineer-in-Incharge in this regard shall be final.) (PerDay means 8 hours/day)

Skilled ( Mason / Carpenter / Plumber / Technician etc.)

Unskilled.

Providing and fixing factory made uPVC door frame made of uPVC extrudedsections having an overall dimension as below (tolerance ±1mm), with wallthickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed withgalvanized brackets and stainless steel screws, joints mitred and Plasticwelded. The hinge side vertical of the frames reinforced by galvanized M.S.tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos.stainless steel hinges fixed to the frame complete as per manufacturer’sspecification and direction of Engineerin- charge.(Brand, Colour, Shade, Texture, Finish to be finalized by NFL Engineer) Extruded section profile size 48x40 mm

30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of stylesand rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm(± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles andrails mitred and joint at the corners by means of M.S. galvanised/ plasticbrackets of size 75x220 mm having wall thickness 1.0 mm and stainless steelscrews. The styles of the shutter reinforced by inserting galvanised M.S. tube ofsize 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of'H' section, a uPVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm)wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S.'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel ofsize not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1mm) wall thickness . The panels filled vertically and tie bar at two places byinserting horizontally 6 mm galvanised M.S. rod and fastened with nuts andwashers, complete as per manufacturer's specification and direction ofEngineer-in-charge.(Brand, Colour, Shade, Finish, Texture to be finalized by NFL Engineer)

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodiccoating not less than grade AC 10 as per IS : 1868 ) transparent or dyed torequired colour or shade, with necessary screws etc. complete :200x10 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coatingnot less than grade AC 10 as per IS : 1868) transparent or dyed to requiredcolour or shade, with necessary screws etc. complete :125 mm

Providing and fixing aluminium work for doors, windows, ventilators andpartitions with extruded built up standard tubular sections/ appropriate Zsections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessaryfilling up the gaps at junctions, i.e. at top, bottom and sides with requiredEPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rustfree, straight, mitred and jointed mechanically wherever required includingcleat angle, Aluminium snap beading for glazing / paneling, C.P. brass /stainless steel screws, all complete as per architectural drawings and thedirections of Engineer-in-charge. (Glazing, paneling and to be paid for separately)

For Fixed Portion:- Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixinghinges/ pivots and making provision for fixing of fittings wherever requiredincluding the cost of EPDM rubber / neoprene gasket required (Fittings shallbe paid for separately) :- Powder coated aluminium (minimum thickness ofpowder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressedthree layer or graded wood particle board conforming to IS: 12823 Grade lType ll, in panelling fixed in aluminum doors, windows shutters and partitionframes with C.P. brass / stainless steel screws etc. complete as perarchitectural drawings and directions of Engineer-in-charge.Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters andpartitions etc. with EPDM rubber / neoprene gasket etc. complete as per thearchitectural drawings and the directions of Engineer-in-charge . (Cost ofaluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness

Providing and fixing white viterous china pedestal for wash basin completewith recessed at the back for reception of pipes and fittings.

Providing and fixing white vitreous china battery based infrared sensoroperated urinal of approx. size 610 x 390 x 370 mm having pre & post flushingwith water (250 ml & 500 ml consumption), having water inlet from back side,including fixing to wall with suitable brackets all as per manufacturersspecification and direction of Engineer-in-charge.

Note: (i) GST shall be paid extra as per NIT. (ii) Bidders may take care the Clause No.1.6.0 (a) of GTC & 1.8.0 of STC while quoting the Rates. (iii) bidders must read all the Clauses of STC and Scope of Work before quoting the rates.

M/S R K GARG CONTRACTOR