CA NO. GE (AF)/SGR-34/2024-25 REPAIR / MAINTENANCE OF BRICK WORK, STONE MASONARY WORK, PCC, DRAIN, PATCH, TILE WORK ETC AT WSA AREA UNDER GE (AF) SRINAGAR.

Amount

Demolition RCC roofs, floors (other than ground floors), columns, beams, staircases, landing, chajjas and similar suspended work (reinforcement cut as required to facilitate demolition), complete all as specified and directed.

M&L for reinforced cement concrete1:2:4, nominal mix, type B-1 (using 20 mm graded crushed stone aggregates) as columns, pillars,piers,posts and struts, complete all as specified and directed.

M&L for reinforced cement concrete1:2:4, nominal mix, type B-1 (using 20 mm graded crushed stone aggregates) as in slab supported on walls,beams and columns, in floors, roofs,chajja, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for coloumns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

All as per Ser item No. 4.00 here in above but 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc, also splays between floors and beam, etc, to rough finished surface of concrete, complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions in square, rectangular shape etc,complete all as specified and directed.

Demolition of stone/boulders or brick masonary built in cment mortor including all quoins, arches, pillars, etc but excluding ashlar facings, dresses stone work and precast concrete articles etc, complete all as specified and directed.

M&L for brick work with sub class 'B' Bricks (using old size bricks) straight or curved on plan exc 6m mean radius, built in CM 1:6, complete all as specified and directed.

M&L for stone walling of random rubble masonry brought up to course, well bonded, bedded and solidly hearted built in CM 1:6, complete all as specified and directed.

M&L for stone walling (except stone) of random rubble masonry brought up to course, well bonded, bedded and solidly hearted built in CM 1:6, complete all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water, etc., complete all as specified and directed.

M&L for 15mm thick rendering on fair faces to brickwork or concrete in CM 1:6 finished the surface even and smooth (without using extra cement , complete all as specified and directed.

M&L for 15mm thick rendering on fair faces to brickwork/other than fair surface surface in CM 1:4 finished the surface even and smooth (without using extra cement , complete all as specified and directed.

Preparation of newly plastered surfaces and applying two coats cement base paint, complete all as specified and directed.

Preparing of new plastered wall surfaces and applying two coats oil bound distemper, complete all as specified and directed.

M&L for PCC 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) as in copings including weathering slightly or chamfered angles etc, complete all as specified and directed.

S&F for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe-290 (Gde E-165) including dismantling of old existing, complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof coverins, complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating manglore pattern GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, complete all as specified and directed.

Preparation of newly steel surfaces of any description, not exc 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Dismantling of unserviceable floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and directed. (Note: Any damage of electric wiring/fittings fitures during execution shall be make good by contractor on his own with out any cost to govt)

M&L for vitrified parking tiles 10mm thick heavy duty exterior grade texured finished of size 300X300 mm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:4, complete all as specified and directed.

M&L for Non skid, ceramic tiles, area of each tile of size 400x400 x7 mm thick, as in floors, set and jointed in neat cement slurry and pointed in white cement with pigment to match the colour of tiles bedded over and including 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

M&L for Non skid, ceramic tiles, area of each tile of size 600x600 x8 mm thick, as in floors, set and jointed in neat cement slurry and pointed in white cement with pigment to match the colour of tiles bedded over and including 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 sqm, on vertical surface such as skirting, dados and risers to steps etc set and jointed in neat cement slurry and pointed in colour cement to match over and including 10 mm thick backing coat in CM 1:4, complete all as specified and directed.

M&L for Glazed ceramic tile 450 x 300 x 7mm thick (coloured) on vertical surfaces such as wall, dados etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 10 mm thick screed bed in CM 1:4, complete all as specified and directed.

M&L for 25mm thick cement concrete, 1:2:4, type B-0 (using 12.5 mm graded crushed stone aggregate) as in sub base of floor finish even and rough to receive further floor finishes (tile/kota stone/ marble), complete all as specified and directed.

Demolition of old PQC / concrete of any description and in any position not other wise specifically provided for and demolished material thrown out of runway premises, complete all as specified and directed.

M&L for hard core of broken stone or boulders of gauge not exc. 63mm deposited, spread and levelled in layers not exc. 15cm thick, watered and rammed to a true surface, complete all as specified and directed.

M&L for 100 mm thick plain cement concrete 1:4:8, Type D-2 (using 40mm graded crushrd stone aggregate) as in sub base filling including all necessary formwork, complete all as specified and directed.

M&L for HDPE Polythene film, 50 micron thick, laid on a coat of bitumen primer @ 0.30 to 0.50 kg per sqm, complete all as specified and directed.

M&L for pavement quality concrete (PQC) work in pavement/ hard standing of flexural strength 40 kg/ per Sqcm in field using 400 kg of cement per cum or as per design mix whichever is higher using non circular synthetic polyster triangular fibre @ 0.25% by weight of cement, thickness of concrete 20 cms, complete all as specified and directed. Note:- (i) Unit rate quoted shall be inclussive steel formwork required. (ii) Polyster triangular fibre shall be measured and paid as "Supply only" under respective Items of BOQ.

Add/ deduct to Serial Item No 34.00 if extra/ less Kg of cement is used for cubic metre, complete all as specified and directed.

Supply only polyster triangular fibres, complete all as specified and directed.

M&L for forming 12mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’, thickness of slab 15 cms, complete all as specified and directed.

M&L for forming contraction (Dummy) joint 65mm deep x 10mm wide as the work proceeds in alternative ways and filled with sealing compound grade 'A' after priming with primer for grade 'A' sealing compound , complete all as specified and directed.

Deduction to be made from BOQ for Schedule 'A' Part-II (Credit Schedule from dismentling/taking down items) worth Rs 1,01,800.00 during AOC. Note :- Tenderers shall not quote for this Schedule.

M/S FAROOQ AND SONS (BID ID -3076380)

M/S GHULAM MOHAMMAD AND CO. (BID ID -3076998)

M/S SA INFRATECH (BID ID -3077244)

M/S Abdul Ahad Rather (BID ID -3075601)

M/S HAJI ZAHOOR HUSSAIN GANIE (BID ID -3076673)

M/S LUCKY BUILDERS (BID ID -3077549)