84865 SPECIAL REPAIRS TO BLDG NO. 10 FGH (MAIN OFFICE, PROJECT OFFICE AND CIPHER OFFICE) OF SIGNAL BRANCH, HQ SOUTHERN COMD UNDER GE (NORTH) PUNE

Amount

B/R PORTION M&L for dismantling Single layer Mangalore Pattern or similar tiles in roofing and rubbish off the premises complete all as directed.

M&L for roof tiles Mangalore pattern interlocking at side joints, laid dry in roofing complete all as specified and as directed.

All as per Serial item No 2.00 above but using existing Mangalore pattern roof tiles obtained from dismantling in Ser. Item No. 1.00 above complete all as specified and directed.

M&L for ridge or hip tiles to suit Manglore pattern of roofing tiles, bedded and jointed in cement mortar (1:4) etc complete all as specified and as directed.

Dismantling tile battens, spaced at spacing exc 15cm centres to centres fixed with nails complete all as specified and as directed.

Dismantling wooden scantling of section 40 sqcm and over at any position complete all as specified and directed..

M&L for 2nd class hard wood, clean sawn, in scantling as in timber work all as specified and as directed.

M&L for 2nd class hard wood, Wrought finish, in scantling as in timber framed and fixed in position work all as specified and as directed.

All as per Serial item No. 08.00 above but except timber complete all as specified and directed.

S & F of mild steel work as in Roof battens, rafters etc and similar work complete using ERW or induction butt welded tubes conforming to IS1161-1998 grade ST.-240, fixed independently with self tapping screw and in iron cleats etc complete all as specified and directed.

M&L for preparation of New steel surfaces of any description over 10cm girth or width and applying Two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting , any gauge or any thickness, as in roof coverings complete all as specified and directed.

S&F of 0.63mm thick galvanised, corrugated/plain mild steel sheeting with two corrugations side lap, fixed with 'J' Bolts and washers, in roofs, walls etc with grade of zinc coating 120gms/ Sqm complete all as specified and as directed.

S&F in repairs 0.56mm thick plain, Aluminium sheeting, alloy 31000H4 in ridges, hips, valley gutter, crumple joint, drip and straight flashing (length and girth as fixed) complete all as specified and as directed.

M&L for PCC (1:2:4) type B1 (using 20mm graded stone aggregates) as in roof kerbs or mud stops rounded or chamfered on edges and as in Coping and similar work complete all as specified and directed.

M&L for Fibre board Eves/Weather Boarding 18 to 20mm thick or Feather Edged 15mm to 20mm thick and fixed with 30mm Lap, complete approved arch pattern any size and shape, including taking down of old existing board any thickness all as specified and as directed.

M&L for Brick work with fly ash bricks, conforming to IS- 12894:2002, Non modular, class designation 75, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 etc all as specifed and directed.

Demolition of brickwork built in cement mortar and rubbish off the premises complete all as specified and directed.

M&L for taking down chowkats or frames with shutters (without taking off shutters from frame) area exc. 1.5 sqm and not exc. 4 sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from frame) area not exc. 1.5 sqm each complete all as specified and directed.

S&F for aluminium powder coated louvered ventilator with provision of exhaust fan using ‘Jindal” aluminium section or equivalent make as specified including glass 3mm thick ordinary quality, frosted glass and stainless steel wire mesh 0.36mm dia wire and 1.40mm aperture etc complete all as specified and directed. (a) SP 20048 (b) Glazing clips 19352

S&F aluminium anodised powder coated three track sliding window with two glazed shutters, one shutter with and including 4mm thick ordinary quality float glass and one shutter with and including stainless steel wire mesh 0.36 mm dia wire and 1.40mm aperture including good quality of bearing, handle, locks, PVC rubber lining of transparent colour etc, complete all as specified and as directed. Catalouge numbers of Jindal company or equivalent make sections : Three track bottom – 20957, Three track top/vertical – 20958, Handle – 20606, Shutter Interlocking – 20605, Shutter Top and bottom – 20604. Glazing Clip 19352

S&F for 5mm thick coloured Aluminium Composite Panel (Sheet) fixed with screws, cover joints filled with silicon and tape as in semi circular/ rectangular sunshade of windows, doors, gate etc or in wall cladding, fixed over frame to shape semi circular/ rectangular complete including taking down existing panel all as specified and as directed. (Note : (i) Frame work shall be measured and paid separately as S&F. (ii) Make / Sample of Aluminium Composite Panel to be approved by contractor from GE prior procurement & execution of Work)

S&F for aluminium anodised framing of square hollow pipe complete all as specified and as directed.

M&L for 15mm thick cement plaster in CM 1:6 on brick or concrete surfaces finished even and smooth as specified and directed.

Taking down cement plaster on brick/ stone walling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for false ceiling of size 1800mm x 1200mm x 12.5mm thick, tapered edge gypsum board (Gypboard) Plain (conforming to IS 2095-Part 1:2011, Certified board) is then screw fixed to ceiling section with 25mm drywall screws {Material-Carbon steel EN-ISO 7049/50, Finish-Case hardened Grey Phosphating} at 230mm centres on ceiling section & 150mm at periphery of ceiling. Finally square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with Gyproc Pro-Fill Jointing compound (Conforms to ASTM C475), Gyproc Joint Paper tape fixed on metal grid of hot dipped galvanized steel sections and suspended as per manufacturer's specifications and instructions including dismantling of ceiling board of any description and any thickness including cover fillets/ grid etc. Including dismantling existing complete all as specified and as directed. Note : Sample / make shall to be approved by GE before placing bulk order.

M&L for plaster of paris decorative cornices/ moulding to the pattern as approved, cross sectional area exceeding 13 Sq.cm and not exceeding 25 Sq.cm and fixed in decorative pattern including preparation of surfaces and applying two coats of oil bound distemper over a coat of primer matching with the colour of ceiling including dismantling existing false ceiling/POP of any size/description complete all as specified and as directed.

M&L for 12 to 12.50mm thick PVC laminated mineral board false ceiling board of size 600 mm x 600 mm on and including GI powder coated grid work with using 32mm x 23.5mm x 1.5 mm thick main tee, 23.5 mm x 23.5 mm x 1.28 mm cross tee and 23.5mm x 23.5mm x 1.5mm angle fixed to wall for false ceiling including necessary supporting hanger with 3.0mm dia GI wire and 'J' bolts washer nuts for securing frame work to ceiling, suspended @ 120 cm C/C both ways, size of grid shall be 605 mm x 605 mm including dismantling of existing ceiling board of any description and any thickness including cover fillets/ grid etc. including dismantling existing old complete all as specified and as directed. Note : (i) Height of ceiling is above 5 metres. (ii) Sample / make of false ceiling shall be got approved by GE before placing bulk order.

S&F in repair Vitreous china Urinal, full stall type, white with waste pipe and CP brass spreader complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plug with and including 60mm long brass screws, pointing around urinal back in cement; flush pipe, grating and union for discharge pipe including CP Urinal spreader for fixing with 15 mm dia pipe complete all as specified and directed.

M&L for 18mm thick plywood, grade BWR, type BB, number of ply 9 Nos, fixed with fevicol and nails for working table/ storage almirah to the size and pattern including taking down existing plywood complete all as specified and directed.

M&L for 12mm thick plywood, grade BWR, type BB, number of ply 7 Nos, fixed with fevicol and nails for working table/ storage almirah to the size and pattern including taking down existing plywood complete all as specified and directed.

M&L for 6mm thick plywood, grade BWR, type BB, number of ply 5 Nos, fixed with fevicol and nails for working table/ storage almirah to the size and pattern including taking down existing plywood complete all as specified and directed.

M&L for 2nd Class soft wood plain fillets, square, rectangular or triangular in section, bull-nosed, splayed, chamfered or rounded on one edge or face, wrought, secured with fevicol and nails or brads, sectional area exc 13 and not exc. 25 Sqcm complete all as specified and as directed.

M&L for 4mm thick one side decorative groove match veneer complete all as specified and as directed.

M&L for two coats of melamine polish with spray guns, compressor etc complete till fine glossy surface is obtained over wooden & wall panelling surface complete all as specified and as directed.

Taking down wall panelling including veneer, plywood & Batten complete all as specified and as directed.

S&F 1st class hardwood (teak wood) Plain, solid, straight, chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints including taking down chowkats/frames and two coats of synthetic enamel paint over a coat of pink primer o two sides of chowkats and one coat of black bituminous paint on one side of chowkats complete all as specified and directed.

S&F for 30mm thick flush shutters solid core construction, with block board core and plywood face panels, commercial type on both sides including second class hard wood plain cover fillets 35mm X 6mm all around the shutters complete all as specified and as directed.

M&L for 0.90mm thick decorative laminate type 1 of surface finish, colour, pattern and size as approved, fixed with approved adhesive as per manufacturer’s instructions on horizontal and vertical surfaces etc. complete all as specified and as directed.

M&L for 0.90mm thick white laminate, type-I of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer’s instruction complete all as specified and as directed.

Taking down shutters of any description of area exc. 1 sqm & not exc 2 sqm each complete all as specified and as directed.

S&F butt hinges 75mm long, 20mm flap width size, of extruded brass with mild steel hinge pin, bright polished and fixed type D-11 complete all as specified and as directed.

S&F brass handles 150mm size decorative type, extruded, fabricated type, polished complete all as specified and as directed.

S&F sliding channel 450mm size, fabricated type, polished complete all as specified and as directed.

S&F sliding channel 600mm size, fabricated type, polished complete all as specified and as directed.

S&F Auto hinges, stainless steel, bright finish or electrogalvanised 30mm width of flaps complete all as specified and directed.

S&F Magnetic catches of brass body and striking plate in complete all as specified and as directed.

M&L for preparation of old treated plastered or unplastered surfaces of wall by removing all loose paints etc removing nails, applying 2mm thick wall care putty whereever required, smoothen the surface with sand paper and finally applying one coat of acrylic distemper complete all as specified and as directed.

M&L for preparation of New plastered or unplastered surfaces of walls, applying 1 to 1.5mm thick wall care putty whereever required, smoothen the surface with sand paper and finally applying two coats of acrylic distemper complete all as specified and as directed.

M&L for applying wall care putty 1 to 1.5 mm thick on walls surfaces complete all as specified and directed.

M&L for applying one coat of alkali resistant priming paint on wall complete all as specified and directed.

M&L for preparation of new wall surfaces and applying two coats of weather proof exterior emulsion paint over one coat of primer to mangalore tiles, roof, parapet, wall, floor etc, on heritage buildings complete all as specified and as directed. (NOTE: (i) This item of work is to be operated upto 15m Building Height. (ii) Rate quoted is deemed to included in the quoted rate. Rate quoted is deemed to be inclusive of necessary scaffolding / security measures as the work is to be carried out. Sample / Make shall be got appoved by the contractor from GE prior procurement and execution of work.)

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as directed.

M&L for 10mm thick wall cladding tiles not exc 0.18 sqm in site over 15mm thick plastering in CM 1:6 all as specified and as directed. NOTE : Colour of the tiles to be approved by GE in consultation with User's.

M&L for double charged vitrified ceremic tiles 8-10 mm thick (square/rectangular) polished, area of each tile exc. 0.42 sqm not exceeding 1 sqm, in flooring etc , laid over and including screed bed of 15 mm thick cement mortar (1:4) and jointed in neat cement slurry and pointed in white or coloured cement to match dark shade complete all as specified and directed. NOTE : Colour of the tiles to be approved by GE in consultation with User's.

All as per Ser. item No. 56.00 above but in skirting/dado and including 10mm thick backing coat in cement mortar 1:3 complete all as specified & directed. NOTE : Colour of the tiles to be approved by GE in consultation with User's

M&L for coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tile exceeding 0.06sq.m but not exceeding 0.11 sqm as in floor etc., colour and pattern, set and jointed in neat cement slurry using grey cement and pointed in white or coloured cement to match the colour of tiles, laid over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and as directed. NOTE : Colour of the tiles to be approved by GE in consultation with User's

M&L for coloured glazed ceramic tiles of size 600mm x 300mm x 7 to 8mm thick highlighter tiles of colour and pattern, as in vertical surface, set and jointed in neat cement slurry using grey cement and pointed in coloured cement to match the colour of tiles over and including 10mm thick backing coat in cement mortar 1:3 including dismantling existing tiling, cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified & directed. NOTE : Colour of the tiles to be approved by GE in consultation with User's

M&L for coloured glazed ceramic tiles of size 600mm x 300mm x 7 to 8mm thick of colour and pattern, as in vertical surface, set and jointed in neat cement slurry using grey cement and pointed in coloured cement to match the colour of tiles over and including 10mm thick backing coat in cement mortar 1:3 including dismantling existing tiling, cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified & directed. NOTE : Colour of the tiles to be approved by GE in consultation with User's.

M&L for 25mm thick coloured glossy rubber moulded chequered cement concrete tiles of area exc. 0.08 Sqm and n.exc 0.16sqm each, set, jointed and pointed in net cement slurry mixed with grey cement and pigment in floors including 15 mm thick screed bed or bedding layer of cement mortar (1:6) for laying floor finishes complete all as specified and as directed.

S&F for 300mm long aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, ISI marked, complete all as specified and as directed.

S&F for 300mm long brass sliding door bolts with sand or die cast brass hasp, staple (bolt type) and fixing bolt with roller or drawn brass bolts, ISI marked, complete all as specified and as directed.

S&F for 200mm long aluminium anodised, barrel tower bolts of extruded section, complete all as specified and as directed.

S&F for 150 mm long aluminium anodised, barrel tower bolts of extruded section, complete all as specified and as directed.

S&F for butt hinges, 100mm size, mild steel cold rolled, medium weight complete all as specified and as directed.

S&F for floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, overall length of cover plate 150mm all as specified and as directed.

S&F for 100mm size brass handles, extruded, fabricated type, polished complete all as specified and as directed.

S&F for 150mm size extruded aluminium alloy handles fabricated type anodised complete all as specified and as directed.

S&F in repairs for aluminium (extruded section) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and as directed.

S&F in repairs for vitreous china coloured wash down water closet (pedestal pattern) cascade type ‘P’ trap or 'S' trap, in built seat cover and flushing cistern, low level, valveless, symphonic action type complete with inlet ball valve, float and handle complete all as specified and as directed.

S&F in repairs Chromium plated single lever extended basin mixer (height 150 mm) without popup waste system with 450mm long braided hoses complete all as specified and as directed.

Taking up or down 15 mm bore steel tubing with all fittings and connections including cleaning for refixing or removal to store complete all as directed.

Taking up or down 20 mm bore steel tubing with all fittings and connections including cleaning for refixing or removal to store complete all as directed.

S&F for 15 mm bore GI tubing 'medium grade' galvanised, with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and as directed.

S&F for 20 mm bore GI tubing 'medium grade' galvanised, with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and as directed.

S&F in repairs brass chromium plated quarter turn two way bib cock with wall flange 15mm dia complete all as specified and as directed.

S&F in repairs chromium plated toilet paper holder complete all as specified and as directed.

S&F in repairs chromium plated soap dish complete all as specified and as directed.

S&F in repair white table top Basin of size 450mm x 300mm x 105 mm fixed in position including fixing of tap, waste pipe etc complete all as specified and directed.

S&F stainless steel health faucet with 1 Mtr tube and hook arrangement complete all as specified and directed.

S&F in repairs chrome plated towel ring square with round flange, complete all as specified and as directed.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid on wall fixed complete all as specified and directed

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid on wall complete all as specified and directed

S&F PVC (SWR) bends, 75 mm bore, any radius with access door complete all as specified and directed.

S&F PVC (SWR) bends, 110 mm bore, any radius with access door complete all as specified and directed.

S&F PVC (SWR) Junction, single, (single T) equal or unequal, 110 mm bore, with access door complete all as specified and directed.

M&L for PVC (SWR) vent cowl, 110 mm bore complete all as specified and directed.

S&F in repair 75 mm bore PVC (SWR) floor trap plain with grating incl jointing with solvent cement complete all as specified and directed.

M&L for 18 to 20mm thick granite (of any type) work ( table rubbed and polished) in steps , jambs. pillars, window cills, cooking platforms and any other platform like in cement mortar (1:4) over and including 10mm thick backing coat in cement mortar (1:3), pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including cutting, edge moulding, full curving the edges complete all as specified and as directed. NOTE : Colour of the granite to be approved by GE in consultation with User's

E/M PORTION Taking down carefully aluminium point wiring (light, fan, socket or power), complete (fitting such as switches,ceiling rose, pendent, regulators etc) removing material to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately and making dood disturbed surfaces of wall by plastering disturbed surface smooth by applying two coats of same colour paint as existing, floor etc. complete all as specified and as directed.

Taking down the existing unserviceable main switch / cut out / DBs of any type / capacity / description as existing at site including MCBs any type and capacity making good the disturbed surfaces by plastering disturbed surface smooth by applying two coats of same colour paint as existing to match with the existing finishes all as specified.

Taking down the existing unservicable sub main wiring of any type / description as existing at site including making good the disturbed surfaces by plastering disturbed surface smooth by applying two coats of same colour paint as existing to match with the existing finishes all as specified.

M&L for point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sqmm (nominal area), two single core, PVC insulated and unsheathed FRLSH cable 1100 Volts grade ISI-694 marked drawn through in and including heavy duty PVC concealed conduit including all accessories, Metal flush box of suitable module, with earth dolly, covered with twin colour (specified by Engr-in- Charge) modular white cover plate & frame after chasing in stone masonry walls etc for accomodating modular switches, sockets, regulators etc including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLSH cable as earth continuity conductor along with wiring and connecting to earth dolly, providing Copper cable sockets plate/ bottle type of adequate size at termination end of cable point wiring in DBs, switch boards, fittings fixtures all as specified and as directed for the following :- (NOTE :- The rates of cutting and chasing will be measured and paid seperately)

One light / wall / exhaust fan point controlled by one, one way switch 6 Amps complete all as specified and as directed.

One ceiling fan point controlled by one, one way switch 6 Amps and regulator (Note : PVC Casing caping / Pipe of size as required at site on surface of ceiling (only for fan point) in lieu of concealed is permitted and is deemed to be included in the unit rate quoated.)

One bell point controlled by one, one way switch 6 Amps complete all as specified and as directed.

One 5 pin socket outlet plug point, 6 Amps, controlled by one, switch on same board complete all as specified and as directed.

One 5 pin socket outlet plug point, 6 Amps, controlled by one, switch on independent board complete all as specified and as directed.

All as per Ser. Item No. 95.00 above but using 2.5 Sqmm single core copper conductor FRLS cable of multistranded PVC insulated unsheathed 1100 Volts grade for one 6 pin socket outlet plug point,16 Amps independent including necessary running of 2.5 Sqmm PVC insulated multistranded copper conductor single core FRLS cable as earth continuity conductor along with wiring and connecting to earth dolly providing Copper cable sockets plate/ bottle type of adequate size at termination end of cable point wiring in DBs, switch boards, fittings fixtures complete all as specified and as directed.

S&F Modular Switch - 6 Amps, Single pole one way, one module complete all as specified and as directed.

S&F Modular Bell push - 6 Amps, Single pole one way, one module complete all as specified and as directed.

S&F Modular Switch - 16 Amps, Single pole one way, one module complete all as specified and as directed.

S & F Modular socket outlet multipurpose 6 Amps, 5 pin, 2 module, complete all as specified and as directed.

S & F Modular socket outlet multipurpose 16 Amps, 6 pin-shuttered type, 2 module, complete all as specified and as directed.

S&F, Ding Dong bell suitable for operation on AC. 230 volts, single pole complete all as specified and as directed.

S&F modular fan step regulator, 120W, 230V AC supply complete all as specified and as directed.

S & F Ceiling rose, 3 phase / PVC / polycarbonate, complete all as specified and as directed.

S&F 20/22 Watt LED Batten aluminium body with Opal Diffuser, IP20, Battery back-up & Functioning as per Product TDS with intregrated electronic driver, connector block, holder, decorative end caps, LED tube light etc complete with all accessories prewired and mounting PVC rectangular block, including provision of flexible copper conductor cable of suitable size from ceiling rose to connector and taking down old unserviceable fitting from existing postion for carrying to store, making good disturbed surfaces complete all as specified and as directed.

S & F for recess mounted 2' x 2' square LED panel 36 watts, 596mm x 596mm x 9mm size, sleek design aluminium housing, polycarbonate diffuser white powder coated finish operating voltage 140 volts - 270 volts, AC, 50 Hz complete all as specified and as directed.

S & F round shape 15 watt LED hanging light for table adjustable type with efficiency of 100 lumens per watt, sleek design metal housing finish operating voltage 150 V - 270 V AC, 50 Hz including all hanging arrangement all as specified and directed.

S & F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting with peanut lenses luminaire with high power LEDs as light source and electronic driver of capacity 25 watts or above with pre wired and necessary mounting arrangements and provision of 2.5 sqmm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade bracket 0.6 to 0.9 mtr long bend to required shape with clamps, nut, bolts complete all as directed.

S & F for wall/ceiling mounted 10 watts, box type light fitting white/ warm white as per site requirement, 230 volts with extruded aluminium heat sink provided for efficient heat dissipation and intregrated electronic driver connector block etc complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED tube 2' x 10 watts complete all as specified and as directed.

M & L for cutting chases in stone masonary wall for concealed conduit wiring, submain etc and making goods, where cutting not exceeding 10 cm in girth all as specified and directed.

S & F for LED down light recess mounted luminare, round/ Square type 15 watts as per site requirement with efficiency of 1500 lumens per watt, Series of downlighters with low depth round & larger dia, powder coated white finish with drop down PC diffuser to deliver low glare illumination with optimized heat sink for efficient heat dissipation and separate replaceable electronic driver suitable for office spaces sleek design white finish operating voltage 150 V-270 V AC, 50 Hz complete all as specified and directed.

Taking down Split/ Window type air conditioner indoor and outdoor unit complete with copper tubing of any size and make and shifting at other place after making necessary opening size, cutting of wall any type/ thickness and re-install / fixing of AC after necessary servicing and making suitable arrangement for fixing of AC complete all as specified and directed by Engr-in-Charge. Note :- Necessary Transportation for shifting of ACs and copper pipe & insulation pipe will be provided by contractor and rate for same shall deemed to be included in quoted rate.

S&F of BLDC ceiling fans complete with blades, down rods and accessories etc. 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated, ISI marked including removal of old unsv fan and deposting to MES store yard of AGE E/M (North) complete all as specified and directed. (Note : (a) Quoted Rate is deemed to inclusive of Stickering/Marking/writing of MES numbers in bottom of ceiling Fan as directed by Engr-in-Charge. (b) Make / Sample of BLDC Ceiling fans will be got approved by contractor from GE prior procurement & execution of Work)

S & F of exhaust fans AC single phase 415 V of size 300 mm sweep with louver complete all as specified and directed.

S & F sheet metal enclosure MCB DB SPN 8 way with 100 Amps rated bus bar 240 Volts double door with magnetic locking system including necessary provision for inserting the DBs in wall by cutting the brick/ stone masonary etc and making good of disturbed surface to match the existing colour of wall complete all as specified and as directed.

S & F of Vertical TPN Distribution Board in sheet metal enclosure double door 4 Way, 415 volts, 50 Hz, suitable for Flush Mounting and surface Mounting & provision for FP MCCB as incomer up to 125 Amps as I/C ( Frame1) and SP/TP MCB's as outgoing (Modules Optium F1+12) , With -100 Amps Copper insulated Busbar assembly for each phase, isolated Neutral bar, 2 Earthbar and Cable ties for cable management, IP 43 - #IK 09 with metal door including necessary cement work and electrical connections complete all as specified and as directed.

S&F of Four pole MCCB, Thermal Release Range 63-100 Amps, Breaking Capacity 10KA, Icu at 415V AC 50Hz, 30 KA complete all as specified and as directed

S & F of SP 5 to 32 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) fixing with the MCB DB complete with connection testing and commissioning complete all as specified and directed.

S & F of 32 Amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of single pole and neutral fixing with the MCB DB complete with connection testing and commissioning complete all as directed and specified.

S & F submain wiring with 2 single core (FRLSH) PVC insulated unsheathed multistranded flexible copper conductor cable, of 6.0 Sqmm and one single core 6.0 Sqmm flame retardent low smoke (FRLSH) PVC insulated, unsheathed, multistranded, flexible copper cable as earthing lead, all as per IS 694/1990 drawn through including concealed in stone masonary PVC conduit and conduit accessories heavy duty ISI marked, providing Copper cable sockets plate/ bottle type of adequate size at termination end of cable point wiring in DBs, switch boards, fittings fixtures all as specified and as directed all as specified and as directed complete all as specified and as directed. (Note :- Two runs of 6sqmm copper wire and one run of earth wire cable of 6 sqmm & PVC conduit shall be measured together as one length).

S & F submain wiring with 2 single core (FRLSH) PVC insulated unsheathed multistranded flexible copper conductor cable of 4.0 Sqmm and one single core 4.0 Sqmm flame retardent low smoke (FRLSH) PVC insulated, unsheathed, multistranded, flexible copper cable as earthing lead, all as per IS 694/1990 drawn through including concealed in stone masonary PVC conduit and conduit accessories heavy duty ISI marked, providing Copper cable sockets plate/ bottle type of adequate size at termination end of cable point wiring in DBs, switch boards, fittings fixtures all as specified and as directed all as specified and as directed complete all as specified and as directed. (Note :- Two runs of 4 Sqmm copper wire and one run of earth wire cable 4 Sqmm & PVC conduit shall be measured together as one length).

S & F sub main wiring with approved colour coding as per IS with four single core PVC insulated FR-LSH cable with stranded copper conductor of size 10 Sqmm nominal area and drawing into PVC non metallic rigid heavy duty PVC conduit and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc two runs of PVC insulated with 10 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire, all as per IS 694/1990 drawn through including concealed in stone masonary PVC conduit and conduit accessories heavy duty ISI marked, providing Copper cable sockets plate/ bottle type of adequate size at termination end of cable point wiring in DBs, switch boards, fittings fixtures all as specified and as directed all as specified and as directed complete all as specified and as directed. (Note :- Four runs of 10 Sqmm copper wire and two runs of earth wire cable of 10 Sqmm & PVC conduit shall be measured together as one length).

S & F sub main wiring with approved colour coding as per IS with four single core PVC insulated FR-LSH cable with stranded copper conductor of size 16 Sqmm nominal area and drawing into PVC non metallic rigid heavy duty PVC conduit and its accessories ISI marked heavy duty of suitable size including concealed in wall in stone masonary etc two runs of PVC insulated with 16 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire, all as per IS 694/1990 drawn through including concealed PVC conduit and conduit accessories heavy duty ISI marked complete all as specified and directed. (Note :- Four runs of 16 Sqmm copper wire and two runs of earth wire cable of 16 Sqmm & PVC conduit shall be measured together as one length).

S&F ISI Marked PVC rigid non-metallic flexible conduit of 25 mm dia inclusive of all tees, bends, elbows reducers, junction box etc and fixing accessories such as couplers, lock nuts, saddles, etc for telephone cable, TV cable and public address system including where required complete all as specified and as directed.

S & F ISI Marked PVC rigid non-metallic flexible conduit of 20 mm dia inclusive of all tees, bends, elbows reducers, junction box etc and fixing accessories such as couplers, lock nuts, saddles, etc for telephone cable, TV cable and public address system including where required complete all as specified and as directed.

S&F in replacement cable tray following size of Wire Mesh Electrozinc finish cable trays with a 50 mm x 100 mm mesh configuration along with all necessary accessories. Electro zinc plated after manufacture in accordance with the EN standard 12 329: at least 155 h of SST. The electrical resistance of the joints must not exceed 50 mΩ and must be tested in accordance with the procedure described in the standard IEC 61537. Assemblies with specific fire-resistant properties must have an E30-E90 certificate issued by an approved laboratory in accordance with the tests described in the standard DIN 4102-12. The wire cable tray short-circuit resistance must be tested by an independent laboratory. For the purpose of assembling the various wire cable tray, only fast coupling systems or screw-based (CE25/CE30) systems must be used. These must be designed, mechanically tested and supplied by the wire cable tray manufacturer. The electrical resistance of the joints must not exceed 50 mΩ and must be tested in accordance with the procedure described in the standard IEC 61537. Rod dia must be from 3.9mm to 5.9mm for different sizes. The loading capacities of the brackets and the hanger torques must be tested in accordance with the standard IEC 61537. The tray along with the accessories should not contain any metallic burrs to avoid damaging of cable insulation. (Note : Make / Sample will be got approved by contractor from GE prior procurement & execution of Work) (Test Certificate : - Two Copies of routine test certificates & Third party SWL certificate have to be submitted along with the Cable Tray as per IEC 61537.)

Cable tray of size 54mm x 50mm x 200mm complete with all accessories.

Cable tray of size 54mm x 50mm x 300mm complete with all accessories.

Supply, installation, testing and commissioning of ceiling mount auto light occupancy, dual technology sensor, adjustable of delay timer, infra red and ultrasonic detection, Dia 8meters IP 20, 3 wire with neutral optimum distance between 2 sensors should be 6 Mtr, stand by consumption 0.8W, fixed directly to a false ceiling with mounting claws (included) or installed in a battibox depth 50 mm complete all as specified and directed. (Note :- All necessary FRLSH copper wires to connect complete lights of office bldg etc are deemed to be included in the rates quoted above for motion sensors)

S&F earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6.3mm thick buried directly in ground vertically (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.50 mtr deep below normal ground level, connecting to GI earth wire 4mm dia by means of bolts, nuts, check nuts, and washers of galvanized iron or steel including 15 mm dia. medium grade protection pipe for earth lead complete with charcoal and common salt including watering arrangement with galvanized iron pipe light grade 20 mm dia, PCC Chamber, CI frame and cover, MS funnel with wire mesh all as shown in electrical plate No. 3 of SSR part I including excavation and earthwork in any type of soil/strata and testing on completion. Note :- GI earth wire 4 mm dia and 15 mm dia protection pipe upto 7.5 mtr from earth plate is deemed to be included in rate quoted.

Taking down ceiling fan of any size/ sweep for repair or taken to work shop for rewinding and refixing the fan after rewinding, cleaning dust, oiling, greasing, servicing, etc as per existing & connecting flexible 3 core cable from ceiling rose to connector of fan complete all as specified and directed. Note - Ball bearing, gun metal bush, rubber reel with clamp, nut-bolts, blade assy, outer body, canopy, rotor, stator etc shall be measured and paid separetaly as 'Supply Only' and rewinding item paid seperately under relevant item.

Supply only for brass GM bush suitable for fan any size complete all as specified and as directed.

Supply only fan clamp with rubber reel insulator/ rubber bush, nuts, check nuts with bolts, washer and lock pin all as specified and as directed.

Supply only bearing No 6201/6202/6203 suitable for ceiling fans complete all as spcified and directed.

Supply only blade assembly for 1200mm sweep ceiling fan made of galvanised Iron sheet with suitable gauge heavy duty, duly welded with connecting brackets complete set of three numbers of make suitable to existing as per sample white in colour complete all as specified & directed.

Supply only Outer body of ceiling fan of make suitable to existing (as per sample) complete top and bottom with nut & bolt, made of aluminium alloy, heavy duty suitable to accomodate thev stator and rotor under item 7 and 8 above for ceiling fan 1200 mm sweep including cleaning all dust etc complete all as specified & directed.

M&L for rewinding of ceiling fan of any size with super enameled copper wire of existing gauge including varnishing and drying complete reassembling and testing of size 1200/1400 mm sweep complete all as specified and as directed.

M&L for electronic PCB Card suitable for Bajaj energos BLDC ceiling fan 1200 mm sweep complete all as specified and as directed.

S&F in replacement for ceiling fan down rods of 15mm bore GI pipe medium grade of 1Mtr/1.5Mtr/2Mtr length including welding and fixing with clamps and nut bolts etc at any height complete all as specified and as directed.

M & L for painting the ceiling fan of 1200mm sweep with one coat with white colour synthetic enamel paint by spraying and filling cavaties with filler, after cleaning all dust etc all as specified and directed.

Sky Vision Construction (BID ID -3480256)