Construction of Main Block of Degree College at Verinag

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Earth work in bulk excavation in hard and dense soil including dressing of sides and ramming of bottoms, lift up to 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed. Extra for every additional lift of 1.5m and disposal Lead upto 50 m. {Septic Tank & Sokage pit)

Porviding and laying of stone soiling below raft foundation, with stone size of 100-250 mm to be hand packed with interstices (if any) to be filled with sand duly to be consolidated and compacted.(Rate on LMR Basis)

Providing and laying in position cement concrete of 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) grade excludingthe cost of centering and shuttering - All work up to plinth level.

Reinforced cement concrete (M20) work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement .

1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supply, filling with river sand /nallah muck in 20cm layers including watering, compacting and dressing under flooring in ground floor.(Rate on LMR Basis)

Form work of steel plates not less than 3.0mm thick M.S. sheets of specified size stiffened with suitable structral frame work true to plane or kit ply plates of not less than 12mm thickness of specifed sizes stiffened with suitable timber frame work prop height upto desired height in pile caps ,plinth beams,all types of suspended floors ,sofits of slabs,sloping areas, sides and soffits of beams ribs ,columns posts, pedestals, ornamental projections upto desired height and thickness complete including its removal for all RCC works from plinth to roof level.(Rate on LMR Basis) .

Steel reinforcement of high strength deformed steel bars of Fe 415 grade (conforming to IS 1786-1985) for R.C.C. work including straightening, cutting, bending,placing in position and binding all complete, from foundation to roof.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 75A in 1:6 cement mortar (1 cement: 6 coarse sand) up to desired height in each floor from plinth to roof level including any recession or arches as per architectural drawings.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately) of first class deodar wood.

Providing and fixing 35mm thick panelled or panelled and glazed shutters for doors, ,of first class kail wood including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors of first class kail wood (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters of 35mm thick.

Providing and fixing 35mm glazed shutters for, windows and clerestory windows of ,first class kail wood using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.

Providing and fixing 35mm thick wire gauge shutters of first class kail wood using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws.

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Supplying and erecting welded built-up/rolled section of M.S/S.S grill of required pattern for ground floor windows as per design including priming coat.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels ,plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Kota stone slab 25 mm thick flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab,including rubbing and polishing complete with base of cement mortar 1 : 4 (1cement : 4 coarse sand) :

Cement concrete flooring of 50 mm thick in 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement complete, with 20 mm nominal size stone aggregate.

Extra for providing and fixing of glass strips in joints of cement concrete flooring: 40mm wide & 4mm thick.

Inner surfaces: i):15 mm thick cement plaster in 1:6 cement mortar , in walls using coarse sand..

ii):12 mm thick cement plaster in 1:4 cement mortar using coarse sand, in ceiling with curing.

External surfaces:15 mm thick cement plaster in 1:6 cement mortar using coarse sand,on exterior wall surfaces with curing.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Distempering with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade.

Applying external plasterd wall surfaces with one coat of water thinnable cement primer of approved brand and manufacture on wall surface :

Finishing External walls with water proofing cement paint of required shade :New work (Two or more coats applied @ 3.84 kg/10 sqm)

providing and applying of primer coat over new wood and wood based surfaces with white primer of specified brand, including cost of sand papering and cleaning the surface.

Painting new wood / wood based surfaces with two or more coats of synthetic Enamel of specified shade and brand to an even shade excluding priming and preparation of surfaces but including cost of sand papering and cleaning.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth..

P/F of Hardweare fitting of ISI Mark of approved brand & Make.

Aluminum Tower Bolts 6"

Stainless steel Handles 8"

Door Stoppers

Linklock L Drops with locking arrangement & necessaries.

Aluminum Tower Bolts 4"

Aluminum Handles 4"

Wind Hooks

Providing & fixing water closet squatting pan (Indian Type W.C pan) with 100mm P or S trap, 10 litre low level P.V.C flushing cistern including flush pipe ( hindware) manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: Orissa pattern white vitereous china W.C. Pan of size 580 X 440 mm with integral type foot rests.

Providing & fixing Ivory White Vitreous China pedestal type water closet (European type W.C. Pan) with seat and lid, 10 litre low level white P.V.C flushing cistern including flush pipe with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures, complete including cutting and making good the walls and floors wherever required (hindware): W.C. Pan with ISI marked white solid plastic seat and lid

Providing & fixing WC including PVC flash cistern with all fittings & fixtures including washbasin stainlesssteel grabs etc completed job for handycaped persons {Hindware Cat No:- 7002}

Providing and fixing wash basin with C.I/M.S brackets, 15mm C.P. Brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required: Ivory White Vitreous China Wash Basin (hindware) size 630x450

Providing fixing of Vitreous china Pedestal (Hindware) of standard pattern for wash basins completely recessed at the back for the reception of pipes and fittings.

Providing & fixing Salem Stainless Steel A ISI 304(18/8) Kitchen Sink as per IS:13983 with C.I. Brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required: 610 X 510 mm bowl depth 200 mm.

Providing & fixing PVC Flexible waste Pipe, of 40mm dia. for sink or wash basin coupling etc. complete.

Providing & fixing Stainless Steel Jali (Grating) with or without hole for waste pipe for N. Trap. Weight not less than 70 gms.

Providing & fixing Mirror of size 600 mm x 400 mm of superior size with bevelled edge with 6mm thick hard board back fixed to wall with wooden cleats and C.P. brass screws & washers complete.

Providing and fixing 600 X 120 X 5 mm glass shelf with edges round of supported on anodised alumunium angle frame with C.P. Brass fittings guard rail complete fixed with 40 mm long screw, rawl plug, etc. Complete.

Providing & fixing C.P. brass Toilet paper holder of complete.

Providing & fixing C.P. Brass Towel rail with C.P. Brass brackets fixed to wooden cleats with C.P. brass screws.

Providing & fixing White Vitreous China flat back or wall corner type lipped front Urinal basin of 430 mm x 260 mm x350 mm & 340mmX410mmX 265 mm Size respectively with automatic flushing Cistern ,of approved make with fittings ,C.I/M.S brackets,standard size of C.P brass flush pipe ,Spreaders with unions and clamps complete.(All in C.P.Brass) with waste fittings as per IS: 2556, C.I trap with out let grating and other couplings in C.P Brass including painting of fittings and brackets,Cuttings and making good the walls and Floors wherever required

Providing & fixing PVC pipe heavy duty (Finolex or equivalent), Water or Vent pipe 75 mm internal diameter with cowl. And necessary bends , junctions, inclusive of rubber washers , adhesives , complete job.

Providing & fixing PVC pipe heavy duty (Finolex or equivalent), Water or Vent pipe 110 mm internal diameter with cowl. And necessary bends , junctions, inclusive of rubber washers , adhesives , complete job.

Providing & fixing of health faucet lever type to control the discharge Including all fixtures complete job

Providing & fixing of gysers of standard 50lts make like Havells or Racold including all fixtures and fittings

Providing and fixing soap cases of C.P. Brass of standard quality

Water Supply

Providing and fixing G.I. Pipes complete with G.I fittings and clamps, including cutting and making good the walls etc.: 15 mm dia. Nominal bore (Medium) jindal/tata make.

Providing and fixing G.I. Pipes complete with G.I fittings and clamps, including cutting and 20 mm dia. Nominal bore (Medium) jindal/tata make.

Providing and fixing G.I. Pipes complete with G.I fittings and clamps, including cutting and making good the walls etc.: 25 mm dia. Nominal bore (Medium) jindal/tata make.

Providing and fixing G.I. Pipes complete with G.I fittings and clamps, including cutting and making good the walls etc.: 40 mm dia. Nominal bore (Medium) jindal/tata make.

Providing and fixing gun metal Gate Valve with C.I. wheel of approved quality (screwed end): 25 mm nominal bore

Providing and fixing ball valve (brass of approved quality complete: 20 mm nominal bore

Providing and fixing15mm dia. Nominal bore Plasticized P.V.C. connection pipe with brass union 45 cms Length.

Providing and fixing brass bib cock ( jaquar/marc) conforming to IS:8931 15mm nominal bore

Providing and fixing 15mm dia. Nominal bore C.P. Brass Angle Valve(Jaquar/marc). Conforming to IS :8391

Providing and fixing 15mm dia. Nominal bore C.P. Brass close whole Basin Mixer (jaquar/marc).

Providing and fixing 15mm dia. Nominal bore C.P. Brass wall Mixer of (jaquar/marc)

Providing and fixing 15mm dia. Nominal bore C.P. Brass Mixer for Kitchen Sink with swinging spout complete (jaquar/marc).

Providing & fixing of C.P brass Nipples 15 mm dia & 25 mm long including all charges complete Job.

Providing & fixing of PVC floor trap including all charges complete job.

Providing & fixing of 75 mm dia vent pipe with cowel complete job.

Providing & fixing of water pump of 2.50 H.P including starter including all accessories & cost involved of Crompton Graves or Kirloskar make.

Providing and placing on terrace 1000 ltrs. Capacity high density polyethylene water storage tank of approved brand and manufacturer e.g. Sintex , Star, Electroplastor equivalent with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes and the base support for tanks and including heavy duty float ball valve of standard quality.

Insulation of G.I Pipes (All Dia) exposed directly to environment by using suitable foam to prevent it from bursting.

Supply & laying of 2nd class sand / dust from approved source free from dirt or other unwanted material including cost & carriage of materials complete.

Providing & laying water proofing treatment in basement / walls of WC’s bathrooms etc by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) 1st layer of slurry of cement @ 0.488 Kg /Sqm mixed with water proofing cement compound @ 0.253 Kg / Sqm. (b) laying 2nd layer of fiber glass cloth when the 1st layer is still green. Overlaps of joints of fiber cloth should not be less than 10 Cm’s. © 3rd layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 Kg/Sqm mixed with water proofing cement compound @ 0.67 Kg/Sqm, mixed with water proofing of cement compound @ 0.67 Kg / Sqm / Coarse sand @ 1.289 Kg/Sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The entire treatment will be taken up to 30 CM on parapet & levied into groove all round. The water proofing compound used be Sica-Reintite. The rate includes preparation of surface, treatment & sealing of all joints, corners, junctions of pipes & masonry with polymer mixed slurry.

Edge (D) moulding 6" wide in corners WC's / Bathrooms etc of cement concrete for sealing of joints to make it water proof including cost & carriage of materials complete job.

Making of brick plateform for Orrisa patteren water closets of size up to 3'-00"X3'-00"X1'-02" all complete.

Cast in situ Design mix of M20 grade and high workability , nominal max size of stone aggregate 20mm, including curing but excluding formwork costs for all RCC works from foundation to roof level i.e floor slabs/floor beams, roof slab and roof beams.

Providing & fixing PVC pipe heavy duty, Water or Vent pipe 160 mm internal diameter with cowl. And necessary bends , junctions, inclusive of rubber washers , adhesives , complete job.

Construction of concrete manhole with C.I cover including cost of all materials. Size (600X600X450 mm)

Providing and Laying of Random rubble stone masonary using nallah stones with bond stones in foundation & plinth dry

Providing and Laying of Random rubble stone masonary using nallah stones with bond stones in foundation & plinth including levelling up with cement concrete 1:6:12 (1 cement:6 coarse sand :12 graded stone aggregate 20mm N/S) with 1:6 mix.

P/F of 16mm dia holding down anchor bolts 500 mm long along with nuts for holding of steel trusses /frames in roof of the building. (Rate on LMR Basis)

Providing and fixing of ist class ceramic glazed wall tiles conforming to IS:13753 of minimum thickness 5mm of approved make like KAJARIA/SOMANY/RAKS or equivalent make in all color, shades except begundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12mm thick bed of cement Mortar 1:3 (1 Cement : 3 coarse sand) and joining with grey cement slurry @3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Internal Electrification Work

SUB HEAD-1 WIRING

Wiring for switch controlled primary light points with 1.5 sq mm FRLS PVC insulated stranded copper conductor 1100 volt grade wires in PVC surface/concealed conduit including cost of providing saddles etc for surface conduiting and/or cost of cutting and filling chases for recessed conduiting and including the cost of providing and fixing a 6 Amp 240 volt grid plate mounted modular switch with modular cover plate in zinc chromate passivated MS box and including the cost of running 1.5 sqmm PVC insulated stranded copper conductor wire for loop earthing complete as per specifications( Group C)

Wiring for switch controlled emergency light points with 1.5 sq mm FRLS PVC insulated stranded copper conductor 1100 volt grade wires in PVC surface / concealed conduit including cost of providing saddles etc for surface conduiting and/or cost of cutting and filling chases for recessed conduiting and including the cost of providing and fixing a 6 Amp 240 volt grid plate mounted modular switch with modular cover plate in zinc chromate passivated MS box and including the cost of running 1.5 sqmm PVC insulated stranded copper conductor wire for loop earthing complete as per specifications and as required

Wiring for ceiling fan points with 1.5 sq mm FRLS PVC insulated stranded copper conductor 1100 volt grade wires in PVC surface / concealed conduit including cost of providing saddles etc for surface conduiting and/or cost of cutting and filling chases for recessed conduiting and including the cost of providing and fixing a 6 Amp 240 volt grid plate mounted modular switch with modular cover plate in zinc chromate passivated MS box with space for mounting an electronic fan regulator and including the cost of running 1.5 sqmm PVC insulated stranded copper conductor wire for loop earthing complete as per specifications.

Wiring for exhaust fan points with 1.5 sq mm FRLS PVC insulated stranded copper conductor 1100 volt grade wires in PVC surface / concealed conduit including cost of providing saddles etc for surface conduiting and/or cost of cutting and filling chases for recessed conduiting and including the cost of providing and fixing a 3 pin 6 Amp shuttered socket outlet and 6 amp 240 volt grid plate mounted modular switch with modular cover plate in zinc chromate passivated MS box and including the cost of running 1.5 sqmm PVC insulated stranded copper conductor wire for loop earthing complete as per specifications.Conduit carrying non-essential wiring shall not have essential or UPS wiring. Wiring for essential and UPS Providing,transportation will have thier own conduit system. No mixing of wiring is allowed.

Providing,transportation & fixing following suitable size modular GI box on surface or in recessas, painting etc.required.

2 Module

4 Module

6 Module

Providing and fixing of following size modular cover plate on existing modular metal boxes etc. as required.

1 or 2 Module

4 Module

6 Module

Providing,transportation and fixing of 6 Amp 3/5 pin modular socket-on the existing modular plate & switch box excluding modular plate as required.

Providing,transportation and fixing of 16 Amp modular switch on the existing modular plate & switch box excluding modular plate as required.

Providing,transportation and fixing of 16 Amp modular socket on the existing modular plate & switch box excluding modular plate as required.

Providing and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Providing and fixing stepped type 2M-electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Providing,transportation and fixing ISI marked medium class PVC conduit on surface/recessed along with accessories including the cost of providing saddles etc for surface conduiting and/or cost of cutting and filling chases for recessed conduiting complete as per specifications as below and as required for sub circuits/ voice/ data/ TV system.

25 mm dia

40 mm dia

Providing,transportation and fixing of RJ-11 modular socket on the existing modular plate & switch box excluding modular plate as required for telephone system

Providing and drawing 2Pair 0.5 sq mm FR PVC insulated annealed copper conductor, unarmored telephone cable in the existing recessed PVC conduit as required.

Providing,transportation and fixing of the following sheet steel clad wall / recess mounting 10 Pair telephone tag block of IDC type constructed from 16 SWG sheet steel, finished with red oxide coating & two coats of paint, with hinged gasketted door and complete with adequately rated and sized telephone terminal block to receive incoming and outgoing wires.

Providing,transportation and fixing of RJ-45 modular socket on the existing modular plate & switch box excluding modular plate as required for networking system

Providing,transportation fixing, laying, testing and commissioning of 4-pair Cat 6e LAN cable in existing concealed / surface conduits in partition wall, complete as requiredTelephone system and computer network will have separate conduit. No mixing of telephone and power wiring is allowed.

SUB HEAD III-SUB MAINS AND CABLES

Wiring for circuits/submains with FRLS PVC insulated stranded copper conductor 1100 volt grade wires in surface/concealed conduit and including FR PVC insulated copper wire for earthing and making suitable end connections complete as required and as below.

2 X 2.5 sq.mm + 1 X 2.5 sq.mm earth wire.

2 X 4 sq. mm + 1 X 4 sq. mm earth wire.

2 X 6 sq. mm + 1 X 6 sq. mm earth wire.

2 X 10 sq. mm + 1 X 10 sq. mm earth wire.

2 X 16 sq. mm + 1 X 16 sq. mm earth wire.

SUB HEAD IV-DISTRIBUTION SYSTEM

Providing,transportation, Providing and fixing following way,horizontal type three pole/single pole and neutral,sheet steel, MCB distribution board, 415/240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator).Non-essential, Emergency and Power will have separate sub main boards. No mixing of wiring is allowed.

6 way TPN double door

8 way TPN double door

12 way SPN double door

16 way SPN double door

Providing and fixing 5 amps to 32 amps rating, 240 volts SP MCB 10kA, "C" curve, miniature circuit breaker suitable in the existing MCB DB complete with connections, testing and commissioning etc.

Providing and fixing following rating, double/four pole, 240/415 volts, DP/TPN MCB 10kA "C" curve in the existing MCB DB complete with connections, testing and commissioning etc. as required.

100 amps TPN

Providing and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Providing and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Providing,transportation , providing and commissioning of following size cable in pipe/ Tray/ clamped to wall with suitable clamps saddles and fixing bolts.

3.5 core 240 Sq mm AL XLPE

3.5 core 120 Sq mm AL XLPE

Laying in ground including the cost digging and back filling with sand and brick protection as required The costs shall include for all cables to be provided with a 1D gap and shall be properly clamped with cable clamps and ties. Identification tags shall be provided for all cables and route markers for cables in ground.

3.5 core 240 Sq mm AL XLPE

3.5 core 120 Sq mm AL XLPE

Providing,transportation and making end termination of the following size XLPE insulated cables 1100 Volt grade including cost of crimping tinned copper heavy duty lugs, brass compression glands, insulation tape and all requisite material for completion of joints.

3.5 core 240 Sq mm AL XLPE

3.5 core 150 Sq mm AL XLPE

Providing,transportation and fixing of 6in dia heavy PVC pipe complete as required.

Providing,transportation ,providing and fixing of 4in dia heavy PVC pipe complete as required .

Providing,transportation and fixing of 50W LED slim flood light.

Providing,transportation,providing and fixing of fan box

Providing,transportation,providing and fixing of fan plates big size

SUB HEAD V-FIXTURES AND FITTING

Supply, transportation and fixing of 1x1 18W surface downlighter with a nominal system lumen output of 2050 lumens and a minimum system efficacy of min100 lm/W complete as required The luminaire shall have a rated system lifetime of 50,000 burning hours at L70 with LG7 The luminaire shall meet IP20 rating with THD<10%. The luminaire housing should made of aluminium and the luminaire optics shall have a high efficiency diffuser with more than 85% transmittance.

Supply, transportation and fixing of 2x2 36W surface downlighter with a nominal system lumen output of 2050 lumens and a minimum system efficacy of 115 lm/W complete as required The luminaire shall have a rated system lifetime of 50,000 burning hours at L70 with LG7 The luminaire shall meet IP20 rating with THD<10%. The luminaire housing should made of aluminium and the luminaire optics shall have a high efficiency diffuser with more than 85% transmittance.

SITC of ISI marked 5star energy saving 1200 mm sweep ceiling fan including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable etc. as required.

SITC of exhaust fan 450 mm sweep in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

Sample of all type of light fixtures / fans / exhaust fans / other fittings shall be approved from architect / site engineer & the sample of each approved fixture / fitting shall be kept & maintained at site.

SUB HEAD VI-Cable Tray

Providing,transportation fixing and installing 150 mm width X 50 mm depth X 1.6 mm thickness size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, inconvenient sections, including bolts & nuts, painting suspenders etc as required.

SUB HEAD VI-EARTHING

Providing,transportation & Installation of earth pit comprising of 75 mm Cu pipe filled with crystalline conductive mixture with copper strip of size 40mm x 6mm of length 2 mtrs with eco friendly backfill compound 50 Kgs etc as required conforming to BIS standards having brick masonary chamber with hinged cover. (General Earthing for Each Panel)

(25 x4) mm GI Strip through PVC sleeve (Electrical Earthing) (From Electrical Earthing Pit to Electrical Earthing Busbar)

Providing and fixing of lightning arrestor finial, made of 25 mm dia 300 mm long, copper tube, having single prong at top, with 85mm dia 3 mm thick copper base plate including holes etc. complete job as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For Horizontal & Vertical run)

Providing,transportation ing and fixing 20 amps, 240 volts, SPN industrial type, socket outlet.

Design, manufacture, supplying fixing in position, testing and commissioning of the following front operated cubicle type, front access, dead back, steel enclosed free standing, dust and vermin proof, switchboard with with hinged and lockable doors complete with interconnections

630 Amps TPN MCCB

250 Amps TPN MCCB

100 Amp DP MCB

125 Amp TPN MCB

63 Amp FP Change over Switch

Cast resin current transformers

Amp & Volt Meter

White phase indicating lamps

Supply and fixing of iron stands for panels

Supply & Installation of earth pit as required

Supply and fixing of GI strip

supply and fixing of spreaders for solid connections of cables with 630Amp MCCB's

supply and fixing of spreaders for solid connections of cables with 250 Amp MCCB's

External Sub-Station & allied works

Supply, installation, testing and commissioning of 250 KVA Sub Station (11/0.433) 3 phase copper wound outdoor type transformer oil immersed ONAN cooled/dry cooled complete with all fittings Make:AE/Electric Field/ABB Complete SITC of Sub station as per JKPDD Standards (Complete job)

Supply, installation, testing and commissioningof 11 kV line on 9 Mt. ST poles with ACSR Rabbit conductor with 52 Mt. span as per JKPDD standards ( Complete job)

A B ENTERPRISES