CERTAIN SANCTIONED SPECIAL REPAIR WORKS AT RANJIT LINES IN MIRAN SAHIB UNDER GE JAMMU

B/R Portion: - Demolition of cement concrete of any description and in any position and removing the rubbish from work site complete all as specified and as directed.

Demolition of brickwork/ stone masonry built in cement mortar including all quoins, arches, pillars, but excluding pre-cast concrete articles complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Demolition/ breaking of drain pipes (salt glazed ware, AC or reinforced concrete) set in cement mortar and taking out off trenches and removing the debris from the site all as specified of 150mm/ 200 mm dia pipe including demolition of cement concrete haunching etc complete all as specified and as directed.

Dismantling AC corrugated, semi corrugated sheets in roof covering complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc), or insulation boards/ slabs/ blankets, any thickness any type including cover fillets complete all as specified and as directed.

Dismantling timber scantling 40 Sqcm and over in section in any position as in unframed work complete all as specified and as directed.

Dismantling timber scantling in fillets, posts, rafters, purlins etc under 40 Sq.cm in section complete all as specified and as directed.

Dismantling Stone slabs laid dry and tiles of any description or thickness in floors, aprons etc. and rubbish off the premises complete all as specified and as directed.

Dismantling wrought iron or mild steel work as in wind tie, grill grating, cooler stand etc complete all as specified and as directed.

Taking down roof trusses above 4 mtr and upto 8 mtr clear span, coupled rafters or trussed beam complete all as specified and as directed.

Taking down chowkhats or frames not exceeding 1.5 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and as directed.

Taking down chowkhats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and as directed.

Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

Taking up or down 15 mm bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down 20 mm bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down 25 mm bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and as directed.

Taking down eaves, gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed.

Brick work with sub class 'B' old size brick straight or curved on plan exceeding 6 mtr mean radius built in cement mortar (1:6) complete all as specified and as directed.

PCC (1:2:4) type B-0 (using 12.5 mm graded crushed stone aggregate) as in back filling, bed block for hold fast, coping, benching on corner of joints etc complete all as specified and as directed.

25 mm thick PCC (1:2:4) type B-0 (using 12.5 mm graded crushed stone aggregate), as in sub base/ floor complete all as specified and as directed.

RCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) nominal mix as in lintal bend including necessery formwork to lintel band etc complete all as specified and as directed.

Providing 75 mm thick plain cement concrete (1:4:8) mix, type D-2 (using 40mm graded crushed stone aggregate) as sub-base floor complete all as specified and as directed.

Providing cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and as directed.

75mm thick cement concrete (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) as in floor/ plinth protection laid in suitable panels finished even and fair all as specified. 6mm joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 85/25 or 80/100 gde and three parts of sand (all by weight) complete all as specified and as directed.

Formwork to sides and soffits of roof beams, tie beams, etc. also splays between floors and beams, etc complete all as specified and as directed.

Structural steel section work as in roof trusses (framed), post, trussed, purlins, Rafter, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections or MS tube pipe) and rolled steel section work as in main and cross beam, purlin, rafter, tubular poles, including distance pieces, cleats etc Fe-410W (Gde E-250) quality including shop coat of primer complete all as specified and as directed.

Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment as in gusset plate, base plate etc complete all as specified and as directed.

Mild steel bolts for diameter of neck not exceeding 12mm with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut exceeding 30cm long complete all as specified and as directed.

Mild steel framed works such as grills, framed guard bars, etc and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and as directed.

TMT bars 10 mm dia and over cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire annealed not less than 0.9 mm dia conforming TMT bars complete all as specified and as directed.

Description all as per Ser item No 31.00 here-in-before but 5 mm dia and over upto and including 10 mm dia in stirrups dia complete all as specified and as directed.

10 mm thick rendering in cement mortar (1:6) on other than fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

15 mm thick rendering in cement mortar (1:4) on fair faces of brick work or concrete surfaces with WPC finished even and smooth without using extra cement complete all as specified and as directed.

Pre-painted galvalume aluminium zinc coating 275 gm/sqm GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPs as in roof covering fixed with self tapping screws or L-type or J-type or cranked hook bolts complete all as specified and as directed.

Pre-painted galvalume aluminium zinc coating gm/sqm GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPs as in ridge of roof fixed with self tapping screws or L-type or J-type or cranked hook bolts complete all as specified and as directed.

Providing and fixing in position suspended false ceiling system using 'E' grid suspended ceiling grid system. The size of grid shall be 600 x 600mm with GI frame work, main runner 39 x 24mm, cross tee 29 x 24mm and wall angle 22.2 x 22.2mm using 4mm thick High Pressure Stream cured non primered classic/ designer variant E-Board ISI Marked IS No 14862-2000. Fibre cement 'E' Board to be placed in the gird of 'E' Grid suspended ceiling grid system duly suspended by 4mm dia GI bar hangers from the purlins of the roof with butterfly clips. All electric fittings fixed with ceiling and refixing the same in position after replacing the ceiling complete all as specified and as directed.

Box type steel windows/ Ventilator (factory made) outer frame made out ERW tube 'P' section 65 x 45 x 25 mm and shutter of ERW tube 'P' section 50mm x 35mm x 20mm openable (double shutter) with glazed shutter on external side and gauzed shutter on internal side including steel pintel hinges steel handle 100 mm long mild steel tower bolt 02 no's on each shutter stopper of 'Z' section and its locking arrangement and mild steel hook and eyes suitable for fixing cooler/ AC window complete all as specified and shown on drawings No CEPZTD-324/07 Sh 1/3 to 3/3 and all as directed. Notes: - The quoted rates shall also include: - (i) One shop coat of zinc chromate primer on all exposed surface and one coat of tar on the ends of steel surface in contact with bricks/ concrete surface. (ii) 4 no's MS steel lugs made of 20 x 5 mm Iron flat 200 mm long. (iii) 10 mm Sq Bar grill/ guard bar design as per drawing. (iv) PCC block for embedding lugs. (v) Two coats of synthetic enamel paint. (vi) Galvanised mild steel wire cloth 0.56 mm nominal dia or wire and average width of aperture 1.0 mm and fixed with tinned tacks or galvanised wire staple complete all as specified and directed.

Aluminium powder coated aluminium door shutters with frame (frame sections not less than 3mm thick, shutter sections not less than 2mm thick. Bottom half panel filled with 8 mm thick prelaminated particle board and top half portion covered with 5.5mm thick frosted glass including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 nos in each door, hinges, anodised aluminium snap beading, screws, two way floor door spring, mortise lock with keys etc. complete all as specified and as directed.

Pressed steel frames (factory made) made out of 1.25 mm thick black mild steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete size of frame 125 x 60mm including bottom of each chowkhat to be welded with 2 No's 25 x 25 x 3mm thick flat iron projecting 10 cm on either side complete all as specified and as directed.

Description all as per Ser item No. 40.00 here-in-before but size of frame 105 x 60mm for fixing of two shutters complete all as specified and as directed.

Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm size comprising of virgin polymer of 'K' value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) and 900 N (Edge), minimum compressive strength 50 N/mm², modulus of elasticity 850 N/mm² and resistance to spread of flame of Class 'A' category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk stainless steel screws complete all as specified and all as per directions of Engineer-in-Charge.

35 mm thick second class hard wood factory made glazed and skeleton shutters, open rebated and prepared to receive glass gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part - I, section 8, clause 8.20 (a) complete all as specified and as directed.

8 mm thick hollow type PVC seamless ceiling panelling of approved make and colour, interlocking tongue and groove type, fixed on concealed GI framework comprising GI perimeter channel 25x25x0.50 mm, GI main runners 45x15x0.50 mm and GI secondary members 25x10x0.50 mm, all made of galvanized steel minimum 0.50 mm thick, suspended from RCC slab/ roof truss with GI hangers (GI flat 25x1.6 mm or 4 mm dia GI wire) at required spacing, including PVC beading, mouldings, cutting and making openings for light fittings, fans, AC diffusers, scaffolding, fasteners and all accessories complete all as specified and as directed by Engineer-in-Charge.

Powder coated aluminium three track sliding type glazed window, shutter with 5mm thick plain sheet glass fixed open track section 100 x 38 x 1.4 mm having three track (two of 5.50 mm thick glass and one of stainless steel wire cloth of 0.56 mm dia and 1.18 mm aperture) with members of window shutters of section 38 x 12mm including aluminium grill 75 mm x 5.50 mm thick pitch diamond shape, wire gauge and grill shall be fixed with the help of 40 mm aluminium flat and other standard Bombay sliding section including all necessary fiber wheel rollers suitable handle to facilitate sliding and all necessary jointing cleats glazing clips, rubber packing, Aluminium snap beading etc complete all as specified and as directed.

Providing and fixing frameless toughened glass door, made of 12mm thick clear float glass, machine cut and polished on all edges. The door shall be factory finished, heat soaked and tested as per IS:2553 (Part - I) for safety glazing. The door includes floor spring mechanism, patch fittings, handles and all accessories for complete installation complete all as specified and as directed.

Non skid ceramic colour tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm screed bed in cement mortar (1:6) complete all as specified and as directed.

Vitrified tiles any colour 10 mm thick (square/ rectangular) polished as in floor, area of each tile not exceeding 0.36 Sqm etc set and jointed over neat 5-6 mm thick approved polymer modified tile adhesive of appropriate grade as per manufacturer's instructions and laid with 3-4mm spacer, spacer gaps to be filled with approved epoxy grout and including screed bed or bedding layer of mortar 15 mm thick cement mortar (1:6) for laying floor finishes complete all as specified and as directed.

Description all as per Ser item No 48.00 here-in-before but in vertical surfaces fixed with 3-4 mm spacer set and jointed over neat 5-6 mm thick approved tile adhesive polymer modified tile adhesive of appropriate grade as per manufacturer instruction and provided with 3-4mm spacer, spacer gaps to be filled with approved epoxy grout complete all as specified and as directed.

Machine cut kota stone slab flooring 18-20mm thick as in floor to match the shade of the slab including 20mm screed bed in cement mortar (1:6) including rubbing polishing complete all as specified and as directed.

Machine cut kota stone slab flooring 18-20mm thick as in riser in step, skirting/ dado to match the shade of the slab including rubbing and polishing over and including 10mm rendering in cement mortar (1:4) complete all as specified and as directed.

Description all as per Ser item No 50.00 here-in-before but in vertical surfaces fixed with 3-4 mm spacer set and jointed over neat 5-6 mm thick approved tile adhesive polymer modified tile adhesive of appropriate grade as per manufacturer instruction and provided with 3-4mm spacer, spacer gaps to be filled with approved epoxy grout and including plastering 10 mm thick cement mortar (1:4) complete all as specified and as directed.

Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster (1:4) (1 cement : 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster (1 : ½ : 2) (1 cement : ½ coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing the top layer with brushes and water to expose the stone chippings complete all as specified and as directed.

16 to 18 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing into white cement (1:2) using marble dust with admixture of pigment to match shade of granite including taking down old complete all as specified and as directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design and pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness and size/ shape, made by table vibratory method using PU mould, laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

Green marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following types including taking down old complete all as specified and as directed.

Providing edge moulding to 16-18mm thick granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and as directed.

Providing edge moulding to 18-20mm thick marble stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and as directed.

Vitreous china water closet pedestal pattern cascade type with inbuilt flushing cistern and seat cover with complete fitting all as specified and as directed.

Vitreous chinaware wash hand basin white, flat back of size 550 x 400 mm excluding tap but including brackets fixing to wall and two no's 10mm dia 100mm long nut and bolt over brackets and chromium plated waste coupling complete all as specified and as directed.

PVC valveless, symphonic action type, flushing cistern, 10 litres capacity, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed.

Extruded aluminium alloy handles fabricated type anodised 150 mm long complete all as specified and as directed.

200 mm long aluminium anodised barrel tower bolt of extruded section ISI marked complete all as specified and as directed.

150 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and as directed.

Floor door stopper of aluminium alloy body and tongue 140 mm anodised with hard drawn steel spring fixed in floor complete all as specified and as directed.

300 mm long dia 16mm aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section complete all as specified and as directed.

Mild steel enamelled helical door spring 150 mm, (ISI Marked) size including roller and roller plate, fixed to wooden/ steel frames by any means as required complete all as specified and as directed by Engineer-in-Charge.

Fancy type brass chromium plated towel ring round with round flange including necessary fittings complete all as specified and as directed.

Stop cock, chromium plated fancy type screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe of size 15mm dia bore complete all as specified and as directed.

125 mm chromium plated stainless steel grating with or without waste hole complete all as specified and as directed.

Health faucet (hand shower) with 1 mtr flexible tube with hot and cold water supply wall hook, bracket etc complete set of superior quality complete all as specified and as directed.

15 mm bore bib taps long nose/ long body, cast copper alloy chromium plated fancy type with capstan head handle screwed down, screwed for brass, weight not less than 450 gms ferrule and fixed complete all as specified and as directed.

15 mm bore Angle valves, cast copper alloy chromium plated fancy type, half turn, screwed down, high pressure, with crutch or butterfly handle, weight not less than 450 gms screwed both ends for iron pipe or for unions complete all as specified and as directed.

15 mm bore sawn neck pillar cock cast copper alloy, chromium plated with angular knob fixed to 15mm dia mild steel pipe complete with all fittings complete all as specified and as directed.

Brass chromium plated towel rail 20 mm dia 'D' type 60 cm long between flanges complete all as specified and as directed.

Mild steel peg set of six power coated as approved by GE complete all as specified and as directed.

Chromium plated brass bib taps with wall flange 15mm fancy type chromium plated cast copper alloy with quarter turn handle and wall flange complete all as specified and as directed.

Chromium plated brass stop/ angle valves 15mm bore fancy type chromium plated with quarter turn handle and wall flange complete all as specified and as directed.

Two way cock/ two way angle cock with wall flange matt chrome finish complete all as specified and as directed.

Fancy type brass chromium plated toilet paper holder with flap including all fittings and fixed complete all as specified and as directed.

Chromium plated 125mm soap dish in postion complete all as specified and as directed by Engineer-in-Charge.

Bib taps, fancy type chromium plated (Short body) with crutch or butterfly handle, screwed down, screwed for iron pipe of 15mm dia bore including necessary fittings complete all as specified and as directed.

Galvanised mild steel wire cloth 0.56 mm nominal dia or wire and average width of aperture 1.0 mm and fixed with tinned tacks or galvanised wire staple complete all as specified and as directed.

3mm thick sheet glass, ordinary quality glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

Curtain rod of stainless steel 20mm dia and side capes fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screw complete all as specified and as directed by Engineer-in-Charge.

Glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket, guard and railing 60cm long complete all as specified and as directed.

500 Litre capacity rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) three layers hoisted and fixed in position and including dismantling of water tank complete all as specified and as directed.

PVC connection 15mm bore and for 600 mm long with brass or PVC nuts and PVC washer complete all as specified and as directed.

Supply and fixing in repair PVC waste pipe 32mm bore complete all as specified and as directed.

15 mm dia galvanized pipes medium grade with all fittings and fixed complete wall and ceiling or laid in floors complete all as specified and as directed.

20 mm dia galvanized pipes medium grade with all fittings and fixed complete wall and ceiling or laid in floors complete all as specified and as directed.

25 mm dia galvanized pipes medium grade with all fittings and fixed complete wall and ceiling or laid in floors complete all as specified and as directed.

20 mm dia Gun metal, globe or gate valve with iron wheel head, screwed both ends for iron pipe complete all as specifed and as directed.

Concrete bed to 150 mm bore pipe (1:4:8) in type D-2 (using 40mm graded crushed stone aggregate) including haunching against the sides of pipe complete all as specified and as directed.

150 mm thick reinforced concrete pipes class NP-2 laid and jointed complete with collars as in trenches complete all as specified and as directed.

Supply and fixing in repairs perforated precast 100 mm thick M-30 RCPC manhole cover, min 800 to 900 mm dia/side of clear opening circular/ rectanuglar and including collar frame set and including lifting hook (02 No's) complete fixed in position over existing manholes complete all as specified and as directed by Engineer-in-Charge.

75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, bends, Tees complete fixed to walls at any height complete all as specified and as directed.

75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, bends, Tees complete laid in trenches or in floors complete all as specified and as directed.

110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, bends, Tees complete fixed to walls at any height complete all as specified and as directed.

110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, bends, Tees complete laid in trenches or in floors complete all as specified and as directed.

PVC (SWR) bends 110 mm radius complete all as specified and as directed.

110 mm PVC (SWR) junction single (T) equal/ Unequal complete all as specified and as directed.

PVC (SWR) bends/ shoes any radius of 75 mm dia complete all as specified and as directed.

PVC (SWR) bends any radius provided with access door of 110mm dia complete all as specified and as directed.

Description all as per Ser item No 105.00 here-in-before but 75 mm dia complete all as specified and as directed.

PVC (SWR) vent cowl of radius of 75 mm dia complete all as specified and as directed.

75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concerete (1:2:4) type B-1 complete all as specified and as directed.

Stack clamps out of 50mm x 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stay to walls or roof for 75 mm bore pipe complete all as specified and as directed.

Stack clamps out of 50mm x 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stay to walls or roof for 100mm bore pipe complete all as specified and as directed.

Preparing surface of new wood and wood based material of any description and girth, not otherwise described and treated with two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Preparing surface of new steel material of any description and girth, not otherwise described and treated with two coats of synthetic enamel paint complete all as specified and as directed.

Preparation of new surface and applying two coats of oil bound distemper new plaster surface over 1 mm thick putty complete all as specified and as directed.

Preparation of new surface and applying two coats of exterior emulsion/ weather proof paint over a coat of primer over and including 1mm thick putty on plastered surface complete all as specified and as directed.

Complete removal of existing surface and preparation of old surface and applying two coats of exterior emulsion/ weather proof paint over a coat of primer over and including 1 mm thick putty on plastered surface complete all as specified and as directed.

Complete removal of existing surface and preparation of old surface and applying two coats of oil bound distemper over 1 mm thick putty complete all as specified and as directed.

Supply only liquid water proofing compound complete all as specified and as directed.

E/M Portion: - Taking down old unserviceable copper/ aluminium point wiring concealed/ batten (light, fan, socket or power) complete including fixtures and fittings such as switches, sockets, ceiling roses, bell push, bell electric, lamp holder, bulk head fitting, pendants, regulators, sockets, light fitting and any type of switch board wooden/ iron, round block etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surface of walls, floors etc complete all as specified and as directed.

Sub main wiring with proper colour coding, insulated, unsheathed, multistranded, copper conductor FRLS, cable of 3 run 6 Sqmm for phase and neutral and one run of 6 Sqmm for earth wire unsheathed, multistranded, copper conductor FRLS, drawn through rigid PVC concealed conduit fixed on wall after cutting chases. Two runs of cable for phase/ neutral and one run of cable for earth will be measured and paid as one unit length including taking down old wiring. Note: - Wiring shall be done in proper colour coding.

Sub main wiring with proper colour coding, insulated, unsheathed, multistranded, copper conductor FRLS, cable of 3 run 4 Sqmm for phase and neutral and one run of 4 Sqmm for earth wire unsheathed, multistranded, copper conductor FRLS, drawn through rigid PVC concealed conduit fixed on wall after cutting chases. Two runs of cable for phase/ neutral and one run of cable for earth will be measured and paid as one unit length including taking down old wiring. Note: - Wiring shall be done in proper colour coding.

Complete Point wiring with 1.5 Sqmm two single core multistranded copper conductor FRLS insulated and unsheathed heavy duty cable in colour code including continuous earth wire with cable of size 1.5 Sqmm copper conductor flexible FRLS insulated drawn in and including concealed PVC rigid conduit medium grade ISI marked after cutting chases in wall, plastering after concealing conduit, including modular grade ISI marked after cutting chases in wall, plastering after concealing conduit, including modular galvanised flush boxes of suitable size and white cover plate with frame as per relevant IS for mounting mdular switches, sockets, fan regulators etc and including making good the disturbed surface as per existing complete all as specified and as directed by Engineer-in-Charge for the following: -

Description all as per Ser item No 121.00 here-in-before but for multi 5 pin 5 amp socket outlet on same board complete all as specified and as directed.

Description all as per Ser item No 121.00 here-in-before but for multi 3 pin socket outlet 5 amp socket on independent board complete all as specified and as directed.

Description all as per Ser item No 121.00 here-in-before but for multi 3 pin 15 Amp socket outlet independent controlled by 15 Amp switch with 2.5 Sqmm copper conductor multistranded cable PVC insulated FRLS and unsheathed cable in and including PVC rigid concealed conduit 20/25mm dia and unsheathed copper conductor multistranded cable 2.5 Sqmm as earth wire FRLS PVC insulated in green colour complete all as specified and as directed by Engineer-in-Charge.

Modular socket, 6A - 5 pin combined 2 module, 240 Volts ISI marked complete all as specified and as directed.

Modular switch 1 way 6A, 1 module, 240 Volts ISI marked complete all as specified and as directed.

Ceiling rose, 3 Phase/ PVC / Polycarbonate isolated body complete all as specified and as directed.

Modular switch 1 way 16A, 1 module, 240 Volts ISI marked complete all as specified and as directed.

Modular socket 6A/16A - 6 pin combined 2 module, 240 Volts ISI marked complete all as specified and as directed.

Material and labour in replacement for Lamp holder, PVC/ polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

Material and labour in replacement self ballast LED retrofit lamp with PVC body and PC Diffuser 9 watt 230 Volt 6500K complete all as specified and as directed.

Supply and fixing in replacement LED light fittings 1 X 18W, 220V, AC decorative box type complete with LED tube rod 18 watts driver, holder and power factor >0.90, 100 Lumen/Watt, 6500K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete (4' ft long) with LED rod 18 watt, 230 Volts, 50 Hz complete all as specified and as directed.

LED luminaire 600mm x 600mm, 35/36 watt, 220V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders and LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed.

Distribution board (TP&N) 4 way double door suitable for MCB TPN 4 pole 63 Amp 16 KA four pole as incomer, it should be IP-43 protected with copper bus bars, neutral links, earthing bar complete all as specified and as directed including taking down old unserviceable DB/MCB any type. Note: - TPN will be measured and paid separately.

Material and labour in replacement for distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 12 way 240 volts double door complete all as specified and as directed. Note: - Distribution board and MCB's should be of same make.

Supply and fixing 415V, 10 KA 'B' curve miniature circuit breaker (MCB) TPN 4 pole, upto 63 Amps in the distribution board complete with connection, testing and commissioning complete all as specified and as directed.

Supply and fixing and fabrication security light bracket made out of 32mm light grade GI tubing suitable for 35 watt LED light grade upto 1.2 mtr length, bend to shape suitable with necessary mild steel clamps with one coat of red oxide and two coats of aluminium paint including nut, bolts, washers etc and including taking out unserviceable bracket and removing from site of work complete all as specified and as directed.

Supply and fixing in replacement LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP-65/66 protection complete all as specified and as directed.

Material and labour in replacement distribution board 4 way sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 240 volts double door complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing modular fan step regulator, 120W - 2 module complete all as specified and as directed.

Earthing complete with galvanised mild steel earth plate electrode of size 600 x 600 x 6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC (1:2:4) type B-1 pre-cast RCC cover slab using reinforcement with suitabe handle made of round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 5 m length for drawing earth lead wire protection, common salt, charcoal etc complete all as shown in electrical plate No 3 of SSR Part - I and testing on completion complete all as specified and as directed.

Taking down of ceiling fans, dismantling blades and depositing to MES store and refixing again after cleaning complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement SPN 63 Amp rating 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB distribution board complete with connection, testing and commissioning complete all as specified and as directed.

Supply and fixing in replacement SPN 32 Amp rating 240V, 10 KA, 'B' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB distribution board complete with connection, testing and commissioning complete all as specified and as directed.

Supply and fixing in replacement 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single pole and current carrying capacity 5 to 32 Amp complete with connection, testing and commissioning complete all as specified and as directed.

Supply, laying for replacement of unserviceable underground LT cable 1100 Volts grade heavy duty electrical cable XLPE insulated and PVC outer sheathing with aluminium stranded conductor, armoured cable 25 Sqmm 4 core cable conforming to IS-7098 Part - I (1988) complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m in width and not exceeding 1.5m in depth and getting out in any type of soil complete all as specified and as directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25cm complete all as specified and as directed.

Removal of excavated surplus material to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

Supply and laying dry river sand as cable cushioning 15cm thick layer before laying and 8cm thick over cable after laying the cable in trenches complete all as specified and as directed.

Supply and laying dry bricks over cable as mechanical protection laid flat with width equal to length of brick with sub class 'B' bricks complete all as specified and as directed.

Material and labour for GI pipe "light grade" for passing of cable through road/ on wall/ on pole with fixed clamps, nuts, bolts for cable protection of size 40mm dia complete all as specified and as directed.

Supply and fixing in repairs of Vertical Distribution Board (TP&N) 4 way double door suitable for and including MCCB 200 Amp 16 KA TP as incomer and outgoing MCB's and should be IP-43 protected with copper bus bars, neutral links, Earthing bar complete all as specified and as directed including taking down old unserviceable distribution board/ MCB's any type. Notes: - (i) Rate includes MCCB TP 200 Amp, 16 KA, 415 volts with adjustable thermal settings. (ii) MCB's shall be measured and paid separately.

Supply and fixing of Polycarbonate modular AC box with 15 amp socket and 32 amps SP MCB complete all as specified and as directed.

Supply and fixing in replacement SP 32 Amp rating 240V, 10 KA, 'B' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB distribution board complete with connection, testing and commissioning complete all as specified and as directed.

Supply and fixing in replacement 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single pole and current carrying capacity 32 Amp complete with connection, testing and commissioning complete all as specified and as directed.

Supply, laying for replacement of unserviceable underground LT cable 1100 Volts grade heavy duty electrical cable XLPE insulated and PVC outer sheathing with aluminium stranded conductor, armoured cable 150 Sqmm 3.5 core cable conforming to IS-7098 Part - I (1988) complete all as specified and as directed.

Material and labour for GI pipe "light grade" for passing of cable through road/ on wall/ on pole with fixed clamps, nuts, bolts for cable protection of size 80mm dia complete all as specified and as directed.