Providing, installation, testing and commissioning of 20000 GPH x 200 meter head raw water HC pump set alongwith LT control panel at pumping station Thill Roun stage-1st (New).

Amount

Providing, installation, testing and commissioning of 20000 GPH x 200 meter head raw water HC pump alongwith LT control panel at pumping station Thill Roun stage-1st (new) by way of loading with crane and shifting of pump motor set from Jammu upto road side near pumping station Thill Roun by mechanical transport, unloading the same from vehicle with the help of crane and manual labour and then dragging / manual carriage up to the pumping station Thill Roun on channels/pipes using pick axes, crowbars, ropes, tripod stand etc. and stacking inside pump-room. The job includes earthwork in bulk excavation around the foundation block on each of the four sides of the block up to the depth of about two meters so as to form a size of approximately 6’x3’x4’.Dumping of excavated material outside the pump room at a distance of about 50 meters. Providing and Fabrication of 6 no. foundation bolts of suitable dia. one meter long by threading them at one end and making of anchor to other end. Laying of bed concrete of 1:4:8 mix using 20 percent aggregate and subsequently laying of RCC of 1:1.5:3 mix including supply/fixing of farm work / shuttering, aggregates, sand and cement, reinforcement steel of 12mm for mesh and all RCC work, angle iron, cleats for supporting/alignment of base-frame including cutting, bending, placing in position and binding, welding, placing of foundation bolts with base frame and making proper alignment of base frame horizontally as well as longitudinally, deployment of vibrator, mixer, tools and tackles etc. and curing complete. Job further includes dragging of pump motor set from the stacked place and then placing them on the base frame by manual labour and other tools and tackles, Leveling and alignment of pump motor set on the base frame by using laminated sheet, strips and coupling there-of. Laying of 150mm dia MS suction and 150mm dia MS delivery pipe lines to the pump set by fabrication and fitting of 150mm dia pipes as per site requirement in the convenient lengths with the help of oxy- acetylene gas cutting and welding. The cut edges shall be grinded with grinder to give them a smooth and even surface and then laying, aligning, welding of suction/delivery pipes in continuous fillet weld using superior quality welding electrodes conforming to ISI specification. The weld should be free from porosity, cracks etc. to create leak proof water tight joints. Providing, fabrication and fitting of 150mm dia MS bends, MS flanges 150mm dia, expanders/reducers, pipe extension pieces to suction and delivery pipe lines, gaskets as per requirement. Providing and fitting of 150mm dia sluice valve CI-1no. to the suction pipe line and NRV 150mm dia and sluice valve 150 mm dia CS-1no. each alongwith bypass system including nuts, bolts, gasket, flanges ,bends to the delivery pipes of pump set. Job further includes cutting of manifold and then welding delivery pipe end with manifold. Job includes greasing work, P/F of graphited gland packing and thereafter testing on no load and then on full load and commissioning thereof. Providing and fitting of electrical components i.e. 120mm2 copper cable approximately 60 meters in length from panel to motors in six leads and from MCCB to panel in three leads with proper laying, thimbling and insulation material. Job further includes providing and fitting of 300mm2 aluminum cable 3.5 core armoured from pole to voltage stabilizer as per site condition approximately 35 meters in length conforming to ISI standards. Providing and fitting of 400 ampere MCCB-1no. of Havel , L&T or other equivalent make on the main board of pump room. Job further includes design, fabrication, installation, testing and commissioning of 225 ampere rating LT control panel cum protection panel for 20000 GPH x 200 meter head pump set. Complete job includes cost of material, machinery, hiring / shifting / carriage charges of material, machinery, tools and tackles, crane, gas cutting appliances, welding set, shuttering, vibrator, mixer, skilled and unskilled labour charges etc. NOTE: - The firm should quote separately for rebate, if any, on old parts / wornout parts / unserviceable items.

GANPATI ELECTRICAL AND MECHANICAL WORKS

N B Engineering and Electric Works