Proposed Construction of Vocational Training Centere Building G Plus 1 at Mandal Kara Simdega in District Jail, Simdega.

Amount

Earth work in excavation in foundation trenches in ordinary soil (vide classification of soil item - A) and disposal of excavated earth to a distance up to 50m. Including all lifts with levelling ramming the foundation trenches removing roots of trees shurbs all complete as per approved design & building specification and direction of E / I

Extra for earth work in hard soil as per specification and direction of E/I (vide classification of soil item - B) Quantity same as per above item no. 1

Earth fillng in foundation trenches and plinth in layers not exceeding 150mm. thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenches wtith a lead of 50M. And lift of 1.5M. All complete as per building specification and direction of E/I (Mode of measurement - compected volume) Quantity same as per item no. 1 i.e.

Providing coarse clean sand filling in foundation trenches and plinth including ramming and watering in layers not exceeding 150mm thick with all leads & lifts including the cost of all materials, labour, royality, & taxes all complete as per building specification and direction of E/I (Mode of measurement - compected volume).

Providing designation 75B one brick flat soling joints filled with local sand including the cost of watering taxes royality all complete as per building specification and direction of E/I.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work up to plinth level:1:2:4(1Cement :2 coarse sand (zone-III):graded stone aggregate 20 mm nominal size).

Providing and laying in position specified grade of reinforced cement concrete,excluding the cost of centering ,shuttering , finishing and reinforcement -All work up to plinth level.

1:1.5:3(1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20mm nominal size)

Providing designation 75 B brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size).

Providing designation 75 B brick work in C.M.(1 :6) in superstructure with approved quality of clean coarse sand of F.M. 2 to2.5 including providing 10 mm thick mortar joints cost of screening materials , scafolding , raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/l.

Extra for brick work for each consecutive floor above first floor including watering and scafolding, all complete as per direction of E/l.

Reinforced cement concrete work in walls (any thickness) includ beams,suspended floors ,roofs having slope upto 15" landing, balcony,shelves,chajjas,lintel,band, plan window,sills staircase and sprial staircase above plinth level upto floor five level excluding cost of ,shuttering finishing and reinforcement with 1:1.5:3 (1 cement :1.5 corse sand (zone-III):3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness) including attached pillasters,buttresses,plinth and string courses fillets ,columns pillars,piers abutments ,post and struts etc.above plinth level ,excluding cost of ,shuttering finishing and reinforcement with 1:1.5:3 (1 cement :1.5 corse sand (zone-III):3 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting,proppingetc.and removal of form for foundation,footing ,bases of colunmns ,etc for mass concrete.

Foundations, footings, bases of columns, etc. for mass concrete

Colums Above Tie C Upto RL

Tie Beam Horiz.

Roof Slab GF+FF

Stairs, (excluding landings) except spiral-staircases

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Water proofrng for Old and New Roof Slab :- Providing and laying water prooflng treatment on roof slab by applying two Component, factory a designed ready to use, acrylic modified flexible,\fbrush, roller or spray eppled wate r proof i n g coati n g as per man ufactl rer specificatio r-(With following steps :- (a)surface preparation :-Provrding and cleaning of concrete surface to remove dLrst, oil, grease including removal of existing loose paint / coating, and cement laitance by cleaning with compressed air & water jet including all materials, labour, tools complete. Ponding test to be done after plugging all outlets and to be checked from sofftt to identify seepage, leakage. On identiiication of seepage, cement grouting to be done with non shrink expanding admixture of Sika lndia Pvt.Ltd. / MYK Schomberg / Dr Fixit/Fosroc or equrivallent. Providing and reparing of all corners and joinis such as those betr,veen the parapet wall and the roof slab etc shall

Covering of treated surface wrth PCC :- Providing 25 mm thick Cement Concrete M20(1:'1.5:3) r'naintaining slope in alternate 2 mIx 2 mt panels with aaproved quality of stone chips of 20 mm to 6 mm size graded and clcaned sand of F M 2 5 io 3 including screening,shuttering,and mixing cerite nt c0ncrete in mixer with admixture of integral water proofing and placing rn position,strikirrg cLrring,t-a]glgnd royality all complete as per buildirrg specifictionJand direction of E/l.Panels that has been left should be casteci nextday.-lhere should be 6 mm gap between Panels.Brand- Sika *Plastocrate plus,MYK proof WP10, Fosroc- Conplast X421ic , Dr Frx,t Prdiproof LWr

Providing and laylng Doublecharge vitrrfied floor tiles in different sizes (thickness to be specified by the manufactre } with water absorption less than 0.08% and confcrming to lS: 15622/ISO 13006 of approved make, in all colours and shadds, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointrng with grey cement slurry @ 3 3 kg/ sqm includin grouling the loints with white cement and matching pigments etc ,complete step tiles & have bullnose,anti and self embossed line size of tiles 600x600 mm

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 1 8 mm thick stone slab over 20 mm (average) thick base of cement mortar 1 : 4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab of colour Black, Cherry/Ruby Red or equivalent

Providing edge moulding to 1 8 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Granite work

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointed with white cement including rubbing, polishing and cost of curing, taxes and royalty all complete as per building specification and direciton of E/l.

Providing TMT steel reinforcement 8mm dia. rod 12mm dia as per approved design & drawing excluding the carriage of M.S. rods (straight or in coils) to work site, cutting, bending, and binding with anneled wire with the cost of wire removel of rust placing the rods in position all complete as per building specification and direction of E/I.

Total Weight (8 mm)Dia steel in M.T

Total Weight (10mm)Dia steel in M.T

Total Weight (12 mm to 20)Dia steel in M.T

Providing and fixing fan hook of 16mm dia M.S. bar 1 metre long bent to required size and shape, placed in position and fixed in R.C.C. slab/beam at the time of casting all complete as per building specification and direction of E/l. (where material is not supplied by deptt.)

Providing 12mm thick cement plaster (1:6) with clean sand of F.M. 1.5 including screening , curing with all leads & lifts of water scaffolding taxes and royality all complete as per building specification and direction of E/I.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding, washing of floors and taxes all complete as per building specification and direction of E/l.

Providing & Applying high quality acrylic modified resin based texture of Dholpur/Red sand stone Pattern with anti algae and UV resistance properties to be applied as intermediate finish in desired pattern @ 43.04 kgs/10 sqm to form film of 1- 1.5 mm thickness after scrapping and properly cleaning the surface to remove loose particles from the plaster surface, followed by top coating with Premium Acrylic Smooth exterior paint with Silicone additives of required shade by two or more coats @ 1.43 litres/10 sqm, complete as the direction of Engineer -in-Charge.

Supplying, fitting and fixing 20mm. dia M.S.grating(inclusive) of one 30x8mm. M.S. flat for height exceeding 1 M with necessary holes to windows making holes in chowkhats, cutting bars to size, fitting and fixing the same in position, including straightening the bars all complete as per building specification and direction of E/l.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:

Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush shutters in doors and windows with black board core blended with high quality phenol formal dehyde synthetic resin both side commercial veneered of standard make with oxidised iron fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Suppling, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows, skylight, fanlights and celetial windows openings, including wedge over clamps all complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all complete as per building specification and direction of E/l

Supplying , fitting and fixing 32 mm thick good quality well dressed and well seasoned sal wood battened shutters, ledged and braced in doors and windows with oxidised iron fittings such as hinges, sliding door, bolts, tower bolts, handles or rings, hooks and eyes, cleats, sand blocks as per schedule taxes and royalty all complete as per building specification and direction of E/l.

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineerin- Charge.

Providing and fixing to existing door frames. 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides.The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter).

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.

80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete.

Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides

Supplying, fitting and fixing callapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2 mm at 100mm. centres and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40x40x6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles, including applying a priming coat of red lead paint, carriage , hoisting and taxes all complete as per building specification and direction of E/l.

Providing two coats of synthetic enamel paint over a coat of primer of approved shade and make over new wooden surface after cleaning, removing dirt, scales, smokes, grease and sand papering, including cost of scaffolding and taxes all complete as per building specfication and direction of E/l.

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing rust , dirt, , scales , smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/l. ( Mode of measurement Area shall be multiplied by the co-efficient as indicated in building specification)

Providing two coats of painting with ready mixed paint of approved shade and make over steel surface including cleaning the surface thoroughly cost of scaffolding and taxes all comple as per building specification and direction of E/I.

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 1.5mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/l.

Providing 250mm. wide brick drain in cement mortar (1:6) with av. 250mm. clear depth and 250mm. apron including cost of earthwork involved with 75 mm. ~ cement concrete (1:4:8) over one brick designation 75A flat soling in proper grade and slope at the base, the drain duly plastered in C.M.(1:3) with punning over exposed surface all complete as per building specification and direction of E/l.

Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS :13592 type A including jointing with seal ring conforming to IS : 4382, leaving 10mm gap for thermal expension, (i) single socketed pipes

110 mm. Dia. PVC pipe,Rate=377.40/1.2254

Providing and fixing on wall face unplasticised PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expension.

Bend 110 mm. dia...,,Rate=150.35/1.2254

Shoe 110 mm dia,.,,Rate=131.85/1.2254

Providing and fixing to the intel mouth of rain water pipe cast iron greetings 15 cm diameter and weighing 440 grams.

Providing and fixing unplasticised PVC pipe cleaps of approved design to unplasticised PVC rain water …. … E/I

110 mm. Dia. PVC pipe

Carriage of materials by diesel truck including loading at source, unloading at works site and stacking properly, labour, P.O.L. etc. all complete as per direction of E/I.

(i) Brick with avg.lead 8 KM (1k+7p)

(ii) Sand with avg.lead10 KM

(iii)Stone chips with avg.lead 22 KM

Providing and fixing Chlorinated polyvinyl Chloride(CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings this includes jointing of pipes & fittings with one step CPVC solvent cement, trenching,refilling & testing of joints complete as per direction of Engineer in Carge.

15 mm nominal outer dia pipes,,Rate=244.70/1.2254

20 mm nominal outer dia Pipes,Rate=274.30/1.2254

32 mm nominal outer dia Pipes,Rate=438.60/1.2254

Making hole in wall for G.I. pipe and restoring the same after pipe laying as per specification and direction of E/I.

(b) 250mm thick wall

Providing and fixing Gun metal full way valve of approved qualtiy, all complete as per specification and direction of E/l

(d) 32 mm dia.wt not less than 700 gms

polythinene water storage tank of mark with covei and-sulta6iE locking system in double layer confirming to lS: 12701-1996 with Latest revision.

Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour

Flush pipe with union spreaders and clamps all in C.P. brass for single stall

Supplying, fitting and fixing viterous white glazed earthen ware wash hand basin of Parry or Hindustan or any other I.S.S. approved make supported on pointed c.l. or R.S. brackets 32m C.I. brass waste 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grms., 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/l.

Supplying, fitting and fixing vitreous white glazed earthen ware indian squating type 600x350mm urinal plate of parry, Hindustan or any other l.S.S. approved make with internal flushing rim, 100mm white glazed earthen ware channelabout 1m. long 5litre capacity C.l. automatic flushing cistern of reliance or any other approved make with fittings R.S. or C.l. brackets 1Smm and 45 cm long PVC / Alkathene pipe standard G.l: flush pipe for backand front with spreader fittings and brass coupling etc. 15 mm C.l. Body'brass spindle stop cock weight not less than 450 grams. all complete including painting of exposed parts with 2 coats of approved paint over a coat of red oxide primer and cutting the wall and floor and making good the same as oer soecification and direction of E/|.(a) 600 mm x 350 mm size (large)

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.,,Rate=111.45/1.2254

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore,Rate=506.80/1.2254

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.15 mm nominal bore,Rate=594.75/1.1512

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931,15mm nominal bore,Rate=500.35/1.1512

Supplying, fitting and fixing viterous white glazed earthen ware I.W.C. of Parry Hindustan or any other I.S.S. approved make with 100 mm H.C.I., "p" trap 15 litres C.I.. or C. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32 mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware where footrest to be fixed in floor 15 mm C.I. body brass spindle stop cock of weight not less than 50 grms. 15 mm P.V.C. connection pipe 450 mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.

Suppling, fitting and fixiilS40mm high-vitreous white glaz-dd earthen E.W.C. with 'p' trap of parry hindustan or any other approved l.S.S. make including supplying and fixing l5litres C.l. mosquito proof low down flushing cistern of approved make with complote fittings with C.l.handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450grams 1Smm P.V.C. alkathene pipe 45cm. long with brass coupling at both ends and white/black plastic solid state seal and lead of commander/cuckoo or other LS.S. make with hinges or screws etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide priming, all complete as per specification and dlrection of E/|.

(b)12.5 lit. low level P.V.C. cistern

Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS :13592 type A including jointing with seal ring conforming to IS : 4382, leaving 10mm gap for thermal expension, (i) single socketed pipes

75 mm. Dia. PVC pipe,Rate=248.80/1.2254

Providing and fixing on wall face unplasticised PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expension.

Single push fit coupler 100 mm. dia. ,,Rate=127.60/1.2254

Providing and fixing unplasticised PVC pipe cleaps of approved design to unplasticised PVC rain water …. … E/I

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit with modular type, Group B

Wiring for light/power plug with 2x4sq.mm FR PVC insulated copper conductor single core cable

Wiring for circuit/submain wiring alongwith earth wire -do-

2x1.5 sq.mm + 1x1.5 sq.mm earth wire

2x2.5 sq.mm + 1x2.5 sq.mm earth wire

2 x 4.0 sq.mm + I x 4.0 sq.mm earth wire

Supplying and fixing following modular type switch/ socket on the existing switch box/cover

5/6 amps, one way switch

5/6 amps, 3 pin socket outlet

15/16 amps, 6 pin socket outlet

S/F light plug point with modular type accessories :- Supplying and fixing suitable GI box with modular plac and cover in front on surface of in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch. corutection, painting etc. as required (For light plugs to be used in non residential buildings)

S/F Modular boxes, base & cover plate :- Supplying and fixing following size / modules , GI box along with modular base & cover plate for modular switches in recess etc as required.I or 2 module (78mmx 78mmx 45mm)

.1or 2 module (78mmx 78mmx 45mm)

6 module (78mm x 205mm x 50mm)

S/F power plug point with modular type accessories :- Supplying and fixing suitable GI box with modular plac and cover in front on surface of in recess, including providing and fxing 6 pin 15/16 amps modular socket outlet and l5/16 amps modular switch. connection, painting letc. as required (For light plugs to be used in non residential buildings)

S/F batten holder

Supplying and fixing batten holder including connection etc. as required.

S/F ceiling rose

Supplying and fixing 2 pin, 5 amps ceiling rose on existing junction box/ wooden block including connection etc. as required.

S/F MCCB in cubical panel board :- Providing and fixing following rating and breaking capacity MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.

125 amps, 16 KA, fxed thermal setting

S/F S.P. MCB DB S/F following way single pole neutral, sheet, MCB distribution board, 240 volts on surface/recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator)

8 way, Double door

S/F following way single pole neutral, sheet, MCB distribution board, 240 volts on surface/recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator)

8 way (8 + 24), Double door, Vertical type

B'series, S.P. MCB :- and fixing 6 amps b 32 amps rating; 240 volts, 10 KA, "8" cutve, circuit breaker suitable for furductive load of following poles in extsttng MCB DB complete with corurecdoru, esting and commissioning as required.

6y'32 amps, single Pole, "8" series

B'series, S.P. MCB :- and fixing 6 amps b 32 amps rating; 240 volts, 10 KA, "8" cutve, circuit breaker suitable for furductive load of following poles in extsttng MCB DB complete with corurecdoru, esting and commissioning as required.

6/32 amps, Single pole

40 amps, SPN

50/63 amps, DP

40 amps, TPN

P/F M.V. danger notice plate :- Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on bottr sides, and with inscription in single red colour on front side as required. lDetails of cost for one each

S/F 15/16 watt LED Bulb

Supply of 9" (230mm) metal exaust fan Fan Bajaj/Crompton or any other approved make etc

S.I.T.C of floowing rating reccess/surface mounted LED round/square shape Down light luminarie with pressure die cast housing for single phase supply voltage. Luminarie shall be confirm to IS:10322 part-5/section-2 or IEC:62722with all neccssary acc$sories as required

18/20W LED Round Down light

Supply Installation, testing and commissioning of follwing size ceiling fan 3 Blades confirming to13:374,.2019 including wiring the down rods of ndard length (upto 30cm) with l.Ssq.mm. FR PVC insulated, copper wire uitable for 230V 50H2, single phase supply etc. complete as required.l200mm (48") Ceiling Fan

S/F Modular type electronic fan regulator :- Supplying and fixing stepped type electronic fan regulator on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

75/ 80W LED Flood light

S.I.T.C of floowing rating surface mounted LED tube light fitting suitable for 230V 50H2, single phase supply etc. complete as required.

20122W LED Tube light

P/p G.I. lightning condutor finial :- Providing and fixing of lighting conductor finial , made of 25mm dia 300mm long , G.I. tube, having single prong at top, with 85mm dia 6mm thick G.I. base plate including holes etc. complete as required.

Pff G.I. lightning conductor tape in horizontal mn :- Providing and fixing G.I. tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete as required.( for Horizontal run ).

PIF G.I. lightning conductor tape in vertical run :- Providing and fxing G.I. tape 20mm x 3rrm thick on parapet or surface of wall for lightning conductor complete as required.( for Vertical run ).

Fixing lightring conductor tape in horizontal run :- Fixing of copper/G.L tape 20mrn x 3mm thick on parapet or surface of wall for lightning conductor complete as required.( for horizontal n n ).

Fixing lightning conductor tape in vertical run :- Fixing of copper/G.I. tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete as required.( for vertical run ).

Earthing with copper earth plate 600mm x 600mm x 3mm thick Including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. as required (but without charcoal or coke and salt)

Salt/ charcoal for plate earth electrode -

Extra for using salt and charcoal for GI or copper plate earth electrode as required.

Laying of one number PVC insulated and PVC sheathed/ XLPE power cable of l.l KV grade of size not exceeding 35 sq mm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Suplying and making cable route marker with cement concrete l:2:4 (l Cement : 2 Coarse sand : 4 graded stone aggregate 20 mm nominal size) of size 60 cm x 60 cm at the bottom and 50 cm x 50 cm at the top with a thickness of l0 cm including inscription duly engraved as required.

PVC/XLPE insulated PVC sheathed heavy duty, armoured electrical cable with aluminiumconductor forworking voltage up to and including L100 volts. (Conformsto IS:1554,part-1)35 sq. mm,3.5 core

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work up to plinth level:1:2:4(1Cement :2 coarse sand (zone-III):graded stone aggregate 20 mm nominal size).1:2:4(1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 40mm nominal size)

Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge 100 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range5 cm to 20 cm, in recharge pit, in the required thickness, for allleads & lifts, all complete as per direction of Engineer-in-charge

Supplying, filling, spreading & leveling gravels of size range 5 mm to10 mm, in the recharge pit, over the existing layer of boulders, inrequired thickness, for all leads & lifts, all complete as per directionof Engineer-in-charge

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mmto 2 mm in recharge pit, in required thickness over gravel layer, for all leads& lifts, all complete as per direction of Engineer -in-charge

DT : Basic rates for 1251115 mm dia Drilled Tube-well for drilling in all kinds of soil and rock for installation of hand pump with DTH rig Machine all complete including supplying all materials, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 1251115 mm dia boring etc. and cost of transporting rig machine and other vehicle up to site of work as per specification and dinection of Engineer lncharge (Basic rates)

Drillig upto 30 mtr Depth below G. L. in Rural Area

Cost of Driling 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.

(a) From 0.00 M to 50.00 M below G.L.

(b) From 51.0 M to 150.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 2HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 1.5 HP

Supplying Full automatic star selta starter to operate induction motor working on 415v 3phase 50hz with no coil. Over load element , On _OFF push buttom with necessary materials and connection to Supply etc complete starter with original sheel steel encloser as per 3914. F.A.S.D starter upto 5 H.P

FR PVC Insulated 3 Core 4 Sqmm copper wire

GI Pipes ( Tata Mark or Equivalent ) as per IS -1239 ( Part -01) 2004 ISI Marked / Medium Quality 40 mm dia

Centering and shuttering including strutting, propping etc. and removal of form for

Lintel

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Add 18 % GST (in Basic Rate must fill 12)

Add 1% Labour Cess (in Basic Rate must fill 1)

Pradeep kumar (BID ID -672036)

SAMSUL HODA (BID ID -672487)